Corrosione atmosferica in area urbana-costiera di un acciaio Cor-Ten: studio del rilascio in ambiente dei metalli di lega

Cor-Ten is a particular kind of steel, belonging to low-alloyed steel; thanks to his aesthetic features and resistance to atmospheric corrosion, this material is largely used in architectural, artistic and infrastructural applications. After environmental exposure, Cor-Ten steel exhibits the characteristic ability to self-protect from corrosion, by the development of a stable and adherent protective layer. However, some environmental factors can influence the formation and stability of the patina. In particular, exposure of Cor-Ten to polluted atmosphere (NOx, SOx, O3) or coastal areas (marine spray) may cause problems to the protective layer and, as a consequence, a release of alloying metals, which can accumulate near the structures. Some of these metals, such as Cr and Ni, could be very dangerous for soils and water because of their large toxicity. The aim of this work was to study the corrosion behavior of Cor-Ten exposed to an urban-coastal site (Rimini, Italy). Three different kinds of commercial surface finish (bare and pre-patinated, with or without a beeswax covering) were examined, both in sheltered and unsheltered exposure conditions. Wet deposition brushing the specimens surface (leaching solutions) are monthly collected and analyzed to evaluate the extent of metal release and the form in which they leave the surface, for example, as water-soluble compounds or non-adherent corrosion products. Five alloying metals (Fe, Cu, Cr, Mn and Ni) and nine ions (Cl-, NO3-, NO2-, SO42-, Na+, Ca2+, K+, Mg2+, NH4+) are determined through Atomic Absorption Spectroscopy and Ion Chromatography, respectively. Furthermore, the evolution and the behaviour of the patina are periodically followed by surface investigations (SEM-EDS and Raman Spectroscopy). After two years of exposure, the results show that Bare Cor-Ten, cheaper than the other analyzed specimens, even though undergoes the greater mass variation, his metal release is comparable to the release of the pre-patinated samples. The behavior of pre-patinated steel, with or without beeswax covering, do not show particular difference. This exposure environment doesn’t allow a completely stabilization of the patina; nevertheless an estimate of metal release after 10 years of exposure points out that the environmental impact of Cor-Ten is very low: for example, the release of chromium in the soluble fraction is less than 10 mg if we consider an exposed wall of 10 m2.

Deposizione elettrochimica di esacianoferrato di rame tramite un metodo "a due step"; caratterizzazione e valutazione delle prestazioni

In this thesis we have identified two electrochemical procedures for preparing two compounds of copper hexacyanoferrate (CuHCF) films with different compositions and structures. The deposition were carried out using a “two steps” method consisting in electrochemical oxidation of previously deposited metallic copper on carbon substrates (glassy carbon and graphite foil electrodes) in K3[Fe(CN)6] solution. Both films, CuHCF-methodA and CuHCF-methodB, were characterized by cyclic voltammetry (GC) and their study using XANES spectroscopy revealed evidence of different structures. Additionally, insertion and extraction of different cations (Na+, K+, Mg2+, Al3+ and Cs+) were performed and the results indicate that CuHCF-methodA has slightly better performances and operational stability than CuHCF-methodB. Data from galvanostatic charge-discharge tests confirme the latter observation. An application for amperometric detection of H2O2 and SEM micrographs are also reported for both films (method A and B). Comparing these results with a previous work of our research group, seems that the deposition of two different compounds using methodA and methodB is due to the different stoichiometry of ions Cu2+ e [Fe(CN)6]3– created near electrode surface during the dissolution step.

Analisi idrogeologica dell'area carsica dei Monti Alburni (Salerno, Campania)

The Alburni Massif is the most important karstic area in southern Italy and It contains about 250 caves. Most of these caves are located on the plateau, between 1500 m a.s.l. and 700 m a.s.l., and only a few reach the underground streams that feed the springs and the deep aquifer. The main springs are Grotta di Pertosa-Auletta (CP1) and Auso spring (CP31), both located at 280 m a.s.l., the first on the south-eastern margin whereas the second on south-west margin, and the springs present in Castelcivita area, the Castelcivita-Ausino system (CP2) and Mulino di Castelcivita spring (CP865), located at 60 m a.s.l.. Some other secondary springs are present too. We have monitored Pertosa-Auletta’s spring with a multiparameter logger. This logger has registered data from November 2014 to December 2015 regarding water level, electric conductivity and temperature. The hydrodynamic monitoring has been supported by a sampling campaign in order to obtain chemical water analyses. The work was done from August 2014 to December 2015, not only at Pertosa but also at all the other main springs, and in some caves. It was possible to clarify the behavior of Pertosa-Auletta’s spring, almost exclusively fed by full charge conduits, only marginally affected by seasonal rains. Pertosa-Auletta showed a characteristic Mg/Ca ratio and Mg2+ enrichment, as demonstrated by its saturation index that always showed a dolomite saturation. All other spring have characteristic waters from a chemical point of view. In particular, it highlights the great balance between the components dissolved in the waters of Mulino’ spring opposed to the variability of the nearby Castelcivita-Ausino spring. Regarding the Auso spring the variable behavior in terms of discharge and chemistry is confirmed, greatly influenced by rainfall and, during drought periods, by full charge conduits. Rare element concentrations were also analyzed and allowed to characterize further the different waters. Based on all these data an updated hydrogeological map of the Alburni massif has been drawn, that defines in greater detail the hydrogeological complexes on the basis of lithologies, and therefore of their chemical characteristics.