Recycling of end of life concrete fines (0 - 4 mm) into silica and cement

The purpose of this work is to find a methodology in order to make possible the recycling of fines (0 - 4 mm) in the Construction and Demolition Waste (CDW) process. At the moment this fraction is a not desired by-product: it has high contaminant content, it has to be separated from the coarse fraction, because of its high water absorption which can affect the properties of the concrete. In fact, in some countries the use of fines recycled aggregates is highly restricted or even banned. This work is placed inside the European project C2CA (from Concrete to Cement and Clean Aggregates) and it has been held in the Faculty of Civil Engineering and Geosciences of the Technical University of Delft, in particular, in the laboratory of Resources And Recycling. This research proposes some procedures in order to close the loop of the entire recycling process. After the classification done by ADR (Advanced Dry Recovery) the two fractions "airknife" and "rotor" (that together constitute the fraction 0 - 4 mm) are inserted in a new machine that works at high temperatures. The temperatures analysed in this research are 600 °C and 750 °C, cause at that temperature it is supposed that the cement bounds become very weak. The final goal is "to clean" the coarse fraction (0,250 - 4 mm) from the cement still attached to the sand and try to concentrate the cement paste in the fraction 0 - 0,250 mm. This new set-up is able to dry the material in very few seconds, divide it into two fractions (the coarse one and the fine one) thanks to the air and increase the amount of fines (0 - 0,250 mm) promoting the attrition between the particles through a vibration device. The coarse fraction is then processed in a ball mill in order to improve the result and reach the final goal. Thanks to the high temperature it is possible to markedly reduce the milling time. The sand 0 - 2 mm, after being heated and milled is used to replace 100% of norm sand in mortar production. The results are very promising: the mortar made with recycled sand reaches an early strength, in fact the increment with respect to the mortar made with norm sand is 20% after three days and 7% after seven days. With this research it has been demonstrated that once the temperature is increased it is possible to obtain a clean coarse fraction (0,250 - 4 mm), free from cement paste that is concentrated in the fine fraction 0 - 0,250 mm. The milling time and the drying time can be largely reduced. The recycled sand shows better performance in terms of mechanical properties with respect to the natural one.

Recycling the city: a sustainable planning framework to reduce, reuse and recycle urban residual spaces

Cities are key locations where Sustainability needs to be addressed at all levels, as land is a finite resource. However, not all urban spaces are exploited at best, and land developers often evaluate unused, misused, or poorly-designed urban portions as impracticable constraints. Further, public authorities lose the challenge to enable and turn these urban spaces into valuable opportunities where Sustainable Urban Development may flourish. Arguing that these spatial elements are at the centre of SUD, the paper elaborates a prototype in the form of a conceptual strategic planning framework, committed to an effective recycling of the city spaces using a flexible and multidisciplinary approach. Firstly, the research focuses upon a broad review of Sustainability literature, highlighting established principles and guidelines, building a sound theoretical base for the new concept. Hence, it investigates origins, identifies and congruently suggests a definition, characterisation and classification for urban “R-Spaces”. Secondly, formal, informal and temporary fitting functions are analysed and inserted into a portfolio meant to enhance adaptability and enlarge the choices for the on-site interventions. Thirdly, the study outlines ideal quality requirements for a sustainable planning process. Then, findings are condensed in the proposal, which is articulated in the individuation of tools, actors, plans, processes and strategies. Afterwards, the prototype is tested upon case studies: Solar Community (Casalecchio di Reno, Bologna) and Hyllie Sustainable City Project, the latter developed via an international workshop (ACSI-Camp, Malmö, Sweden). Besides, the qualitative results suggest, inter alia, the need to right-size spatial interventions, separate structural and operative actors, involve synergies’ multipliers and intermediaries (e.g. entrepreneurial HUBs, innovation agencies, cluster organisations…), maintain stakeholders’ diversity and create a circular process open for new participants. Finally, the paper speculates upon a transfer of the Swedish case study to Italy, and then indicates desirable future researches to favour the prototype implementation.

Analysis of Lead-Acid batteries with a third-order dynamical model

Electrical energy storage is a really important issue nowadays. As electricity is not easy to be directly stored, it can be stored in other forms and converted back to electricity when needed. As a consequence, storage technologies for electricity can be classified by the form of storage, and in particular we focus on electrochemical energy storage systems, better known as electrochemical batteries. Largely the more widespread batteries are the Lead-Acid ones, in the two main types known as flooded and valve-regulated. Batteries need to be present in many important applications such as in renewable energy systems and in motor vehicles. Consequently, in order to simulate these complex electrical systems, reliable battery models are needed. Although there exist some models developed by experts of chemistry, they are too complex and not expressed in terms of electrical networks. Thus, they are not convenient for a practical use by electrical engineers, who need to interface these models with other electrical systems models, usually described by means of electrical circuits. There are many techniques available in literature by which a battery can be modeled. Starting from the Thevenin based electrical model, it can be adapted to be more reliable for Lead-Acid battery type, with the addition of a parasitic reaction branch and a parallel network. The third-order formulation of this model can be chosen, being a trustworthy general-purpose model, characterized by a good ratio between accuracy and complexity. Considering the equivalent circuit network, all the useful equations describing the battery model are discussed, and then implemented one by one in Matlab/Simulink. The model has been finally validated, and then used to simulate the battery behaviour in different typical conditions.