Dielectrophoresis (dep) and electrowetting (ewod) as an anti-fouling process for antibacterial surfaces

Nowadays the medical field is struggling to decrease bacteria biofilm formation which leads to infection. Biomedical devices sterilization has not changed over a long period of time. This results in high costs for hospitals healthcare managements. The objective of this project is to investigate electric field effects and surface energy manipulation as solutions for preventing bacteria biofilm for future devices. Based on electrokinectic environments 2 different methods were tested: feasibility of electric gradient through mediums (DEP) reinforced by numerical simulations; and EWOD by the fabrication of golden interdigitated electrodes on silicon glass substrates, standard ~480 nm Teflon (PTFE) layer and polymeric gasket to contain the bacteria medium. In the first experiment quantitative analysis was carried out to achieve forces required to reject bacteria without considering dielectric environment limitations as bacteria and medium frequency dependence. In the second experiment applied voltages was characterized by droplets contact angle measurements and put to the live bacteria tests. The project resulted on promising results for DEP application due to its wide range of frequency that can be used to make a “general” bacteria rejecting; but in terms of practicality, EWOD probably have higher potential for success but more experiments are needed to verify if can prevent biofilm adhesion besides the Teflon non-adhesive properties (including limitations as Teflon breakthrough, layer sensitivity) at incubation times larger than 24 hours.

Computer aided design and finite element modeling to predict bulk mechanical properties of bone scaffolds using triply periodic minimal surfaces (progettazione assistita al calcolatore ed analisi con il metodo degli elementi finiti per predire il comportamento meccanico di scaffolds ossei creati con l'uso di superfici minime periodiche in tre direzioni)

The aim of Tissue Engineering is to develop biological substitutes that will restore lost morphological and functional features of diseased or damaged portions of organs. Recently computer-aided technology has received considerable attention in the area of tissue engineering and the advance of additive manufacture (AM) techniques has significantly improved control over the pore network architecture of tissue engineering scaffolds. To regenerate tissues more efficiently, an ideal scaffold should have appropriate porosity and pore structure. More sophisticated porous configurations with higher architectures of the pore network and scaffolding structures that mimic the intricate architecture and complexity of native organs and tissues are then required. This study adopts a macro-structural shape design approach to the production of open porous materials (Titanium foams), which utilizes spatial periodicity as a simple way to generate the models. From among various pore architectures which have been studied, this work simulated pore structure by triply-periodic minimal surfaces (TPMS) for the construction of tissue engineering scaffolds. TPMS are shown to be a versatile source of biomorphic scaffold design. A set of tissue scaffolds using the TPMS-based unit cell libraries was designed. TPMS-based Titanium foams were meant to be printed three dimensional with the relative predicted geometry, microstructure and consequently mechanical properties. Trough a finite element analysis (FEA) the mechanical properties of the designed scaffolds were determined in compression and analyzed in terms of their porosity and assemblies of unit cells. The purpose of this work was to investigate the mechanical performance of TPMS models trying to understand the best compromise between mechanical and geometrical requirements of the scaffolds. The intention was to predict the structural modulus in open porous materials via structural design of interconnected three-dimensional lattices, hence optimising geometrical properties. With the aid of FEA results, it is expected that the effective mechanical properties for the TPMS-based scaffold units can be used to design optimized scaffolds for tissue engineering applications. Regardless of the influence of fabrication method, it is desirable to calculate scaffold properties so that the effect of these properties on tissue regeneration may be better understood.

The role of paved surfaces in the Urban Heat Island phenomenon: Assessment of fundamental thermal parameters and finite element analysis for UHI mitigation

Nowadays the environmental issues and the climatic change play fundamental roles in the design of urban spaces. Our cities are growing in size, many times only following immediate needs without a long-term vision. Consequently, the sustainable development has become not only an ethical but also a strategic need: we can no longer afford an uncontrolled urban expansion. One serious effect of the territory industrialisation process is the increase of urban air and surfaces temperatures compared to the outlying rural surroundings. This difference in temperature is what constitutes an urban heat island (UHI). The purpose of this study is to provide a clarification on the role of urban surfacing materials in the thermal dynamics of an urban space, resulting in useful indications and advices in mitigating UHI. With this aim, 4 coloured concrete bricks were tested, measuring their emissivity and building up their heat release curves using infrared thermography. Two emissivity evaluation procedures were carried out and subsequently put in comparison. Samples performances were assessed, and the influence of the colour on the thermal behaviour was investigated. In addition, some external pavements were analysed. Albedo and emissivity parameters were evaluated in order to understand their thermal behaviour in different conditions. Surfaces temperatures were recorded in a one-day measurements campaign. ENVI-met software was used to simulate how the tested materials would behave in two typical urban scenarios: a urban canyon and a urban heat basin. Improvements they can carry to the urban microclimate were investigated. Emissivities obtained for the bricks ranged between 0.92 and 0.97, suggesting a limited influence of the colour on this parameter. Nonetheless, white concrete brick showed the best thermal performance, whilst the black one the worst; red and yellow ones performed pretty identical intermediate trends. De facto, colours affected the overall thermal behaviour. Emissivity parameter was measured in the outdoor work, getting (as expected) high values for the asphalts. Albedo measurements, conducted with a sunshine pyranometer, proved the improving effect given by the yellow paint in terms of solar reflection, and the bad influence of haze on the measurement accuracy. ENVI-met simulations gave a demonstration on the effectiveness in thermal improving of some tested materials. In particular, results showed good performances for white bricks and granite in the heat basin scenario, and painted concrete and macadam in the urban canyon scenario. These materials can be considered valuable solutions in UHI mitigation.

The wind profile in the atmospheric stable boundary layer over complex terrain and heterogeneous surfaces: limitations of local similarity theory

L'indagine ha riguardato il profilo del vento nei primi 30 metri dello strato limite atmosferico stabile nell'ambito della teoria di similarità locale. Ad oggi, diversi esperimenti hanno confermato la validità della teoria per strati-limite su terreni livellati e superfici omogenee. Tali condizioni ideali sono però infrequenti nella realtà ed è perciò importante capire quali siano i limiti della similarità locale per strati-limite su terreni complessi e superfici disomogenee. Entrambe le condizioni sono presenti a Ny-Alesund (Svalbard, Norvegia) dove il Consiglio Nazionale delle Ricerche (CNR), nel 2009, ha installato una torre di 30 m, la Amudsen-Nobile Climate Change Tower (CCT), per lo studio dello strato-limite artico. Il lavoro di tesi ha riguardato misure di vento e turbolenza acquisite sulla CCT da maggio 2012 a maggio 2014. Il confronto tra le velocità del vento misurate dagli anemometri installati sulla CCT, ha rivelato criticità nel dato sonico manifestatesi con sovrastime sistematiche e maggiore erraticità rispetto alle misure provenienti dagli anemometri a elica. Un test condotto fra diversi metodi per il calcolo dei gradienti verticali della velocità del vento ha rivelato scarsa sensibilità dei risultati ottenuti al particolare metodo utilizzato. Lo studio ha riguardato i gradienti verticali adimensionali della velocità del vento nei primi 30-m dello strato limite stabile. Deviazioni significative tra i tra le osservazioni e i valori predetti dalla similarità locale sono state osservate in particolare per i livelli più distanti dal suolo e per valori crescenti del parametro di stabilità z/L (L, lunghezza di Obukhov locale). In particolare, si sono osservati gradienti adimensionali inferiori a quelli predetti dalle più usate relazioni di flusso-gradiente. Tali deviazioni, presenti perlopiù per z/L>0.1, sono state associate ad un effetto di accentuazione della turbolenza da parte delle irregolarità del terreno. Per condizioni meno stabili, z/L<0.1, scarti positivi tra i gradienti osservati e quelli attesi sono stati attribuiti alla formazione di strati limite interni in condizioni di vento dal mare verso la costa. Sono stati proposti diversi metodi per la stima dell'effetto della self-correlazione nella derivazione delle relazioni di flusso-gradiente, dovuta alla condivisione della variabile u*. La formula per il coefficiente lineare di self correlazione e le sue distribuzioni di probabilità empiriche sono state derivate e hanno permesso di stimare il livello di self-correlazione presente nel dataset considerato.

Geometric properties of 2-dimensional minimal surfaces in a sub-Riemannian manifold which models the Visual Cortex

In this paper we study the notion of degree forsubmanifolds embedded in an equiregular sub-Riemannian manifold and we provide the definition of their associated area functional. In this setting we prove that the Hausdorff dimension of a submanifold coincides with its degree, as stated by Gromov. Using these general definitions we compute the first variation for surfaces embedded in low dimensional manifolds and we obtain the partial differential equation associated to minimal surfaces. These minimal surfaces have several applications in the neurogeometry of the visual cortex.

PM and material decay: analysis of dry depositions on horizontal and vertical surrogate surfaces through a Deposition Box system

Airborne Particulate Matter (PM), can get removed from the atmosphere through wet and dry mechanisms, and physically/chemically interact with materials and induce premature decay. The effect of dry depositions is a complex issue, especially for outdoor materials, because of the difficulties to collect atmospheric deposits repeatable in terms of mass and homogeneously distributed on the entire investigated substrate. In this work, to overcome these problems by eliminating the variability induced by outdoor removal mechanisms (e.g. winds and rainfalls), a new sampling system called ‘Deposition Box’, was used for PM sampling. Four surrogate materials (Cellulose Acetate, Regenerated Cellulose, Cellulose Nitrate and Aluminum) with different surfaces features were exposed in the urban-marine site of Rimini (Italy), in vertical and horizontal orientations. Homogeneous and reproducible PM deposits were obtained and different analytical techniques (IC, AAS, TOC, VP-SEM-EDX, Vis-Spectrophotometry) were employed to characterize their mass, dimension and composition. Results allowed to discriminate the mechanisms responsible of the dry deposition of atmospheric particles on surfaces with different nature and orientation and to determine which chemical species, and in which amount, tend to preferentially deposit on them. This work demonstrated that “Deposition Box” can represent an affordable tool to study dry deposition fluxes on materials and results obtained will be fundamental in order to extend this kind of exposure to actual building and heritage materials, to investigate the PM contribution in their decay.

Excited state energy surfaces of flexible emitters for thermally activated delayed fluorescence

Organic Light-Emitting Diodes (OLEDs) technology has matured over recent years, reaching the commercialization level and being used in various applications. The required efficiency can be achieved by transforming triplet excitons into singlet states via Reverse InterSystem Crossing (RISC), which a general mechanism called thermally activated delayed fluorescence (TADF). Two prototypical molecules in the field, 2CzBN and 4CzBN, Carbazole Benzonitrile (donor-acceptor) derivatives, possess similar energy gap between singlet and triplet (∆EST, a key parameter in the RISC rate), but different TADF performance. In this sense, other parameter must be considered to explain these different behaviors. In this work, we theoretically investigate 2CzBN and 4CzBN and address the problem of how flexible donor-acceptor (D-A) or donor-acceptor-donor (D-A-D) molecular architectures affect the nature of excited state, and the oscillator strength. Furthermore, we analyze the RISC rates as a function of the conformation of the carbazole side groups, considering the S0, S1, T1 and T2 states. The oscillator strength of 4CzBN is higher than of 2CzBN, which, in turn, is almost vanishing, resulting in only 4CzBN being a TADF active molecule. We also note the presence of a second triplet state T2 lower in energy than S1, and that the reorganization energies, associated to the RISC processes involving T1 and T2, are both important factor in differentiating the rates in 2CzBN and 4CzBN. However, the 4CzBN RISC rate from T2 to S1 is surprisingly high with respect to the one from T1 to S1, although, according to EL-Sayed rules, since T2 (CT/LE) is more similar to S1 (CT) than in 2CzBN (LE, CT), this transition should be less favored. These insights are important to understand the photophysics of the TADF process and to design novel TADF emitters based on the benzo-carbazole architecture.

Mitigating non-Lambertian surfaces issues in Stereo Matching with Neural Radiance Fields

Depth estimation from images has long been regarded as a preferable alternative compared to expensive and intrusive active sensors, such as LiDAR and ToF. The topic has attracted the attention of an increasingly wide audience thanks to the great amount of application domains, such as autonomous driving, robotic navigation and 3D reconstruction. Among the various techniques employed for depth estimation, stereo matching is one of the most widespread, owing to its robustness, speed and simplicity in setup. Recent developments has been aided by the abundance of annotated stereo images, which granted to deep learning the opportunity to thrive in a research area where deep networks can reach state-of-the-art sub-pixel precision in most cases. Despite the recent findings, stereo matching still begets many open challenges, two among them being finding pixel correspondences in presence of objects that exhibits a non-Lambertian behaviour and processing high-resolution images. Recently, a novel dataset named Booster, which contains high-resolution stereo pairs featuring a large collection of labeled non-Lambertian objects, has been released. The work shown that training state-of-the-art deep neural network on such data improves the generalization capabilities of these networks also in presence of non-Lambertian surfaces. Regardless being a further step to tackle the aforementioned challenge, Booster includes a rather small number of annotated images, and thus cannot satisfy the intensive training requirements of deep learning. This thesis work aims to investigate novel view synthesis techniques to augment the Booster dataset, with ultimate goal of improving stereo matching reliability in presence of high-resolution images that displays non-Lambertian surfaces.