Recycling of end of life concrete fines (0 - 4 mm) into silica and cement

The purpose of this work is to find a methodology in order to make possible the recycling of fines (0 - 4 mm) in the Construction and Demolition Waste (CDW) process. At the moment this fraction is a not desired by-product: it has high contaminant content, it has to be separated from the coarse fraction, because of its high water absorption which can affect the properties of the concrete. In fact, in some countries the use of fines recycled aggregates is highly restricted or even banned. This work is placed inside the European project C2CA (from Concrete to Cement and Clean Aggregates) and it has been held in the Faculty of Civil Engineering and Geosciences of the Technical University of Delft, in particular, in the laboratory of Resources And Recycling. This research proposes some procedures in order to close the loop of the entire recycling process. After the classification done by ADR (Advanced Dry Recovery) the two fractions "airknife" and "rotor" (that together constitute the fraction 0 - 4 mm) are inserted in a new machine that works at high temperatures. The temperatures analysed in this research are 600 °C and 750 °C, cause at that temperature it is supposed that the cement bounds become very weak. The final goal is "to clean" the coarse fraction (0,250 - 4 mm) from the cement still attached to the sand and try to concentrate the cement paste in the fraction 0 - 0,250 mm. This new set-up is able to dry the material in very few seconds, divide it into two fractions (the coarse one and the fine one) thanks to the air and increase the amount of fines (0 - 0,250 mm) promoting the attrition between the particles through a vibration device. The coarse fraction is then processed in a ball mill in order to improve the result and reach the final goal. Thanks to the high temperature it is possible to markedly reduce the milling time. The sand 0 - 2 mm, after being heated and milled is used to replace 100% of norm sand in mortar production. The results are very promising: the mortar made with recycled sand reaches an early strength, in fact the increment with respect to the mortar made with norm sand is 20% after three days and 7% after seven days. With this research it has been demonstrated that once the temperature is increased it is possible to obtain a clean coarse fraction (0,250 - 4 mm), free from cement paste that is concentrated in the fine fraction 0 - 0,250 mm. The milling time and the drying time can be largely reduced. The recycled sand shows better performance in terms of mechanical properties with respect to the natural one.

Chemical composition modification of casting aluminium alloys for engine applications

The research activities were focused on evaluating the effect of Mo addition to mechanical properties and microstructure of A354 aluminium casting alloy. Samples, with increasing amount of Mo, were produced and heat treated. After heat treatment and exposition to high temperatures samples underwent microstructural and chemical analyses, hardness and tensile tests. The collected data led to the optimization of both casting parameters, for obtaining a homogeneous Mo distribution in the alloy, and heat treatment parameters, allowing the formation of Mo based strengthening precipitates stable at high temperature. Microstructural and chemical analyses highlighted how Mo addition in percentage superior to 0.1% wt. can modify the silicon eutectic morphology and hinder the formation of iron based β intermetallics. High temperature exposure curves, instead, showed that after long exposition hardness is slightly influenced by heat treatment while the effect of Mo addition superior to 0,3% is negligible. Tensile tests confirmed that the addition of 0.3%wt Mo induces an increase of about 10% of ultimate tensile strength after high temperature exposition (250°C for 100h) while heat treatments have slight influence on mechanical behaviour. These results could be exploited for developing innovative heat treatment sequence able to reduce residual stresses in castings produced with A354 modified with Mo.

Effects of acute temperature increase on performance and survival of Caribbean echinoids

Climate change is occurring at a faster rate than in the past, with an expected increase of mean sea surface temperatures up to 4.8°C by the end of this century. The actual capabilities of marine invertebrates to adapt to these rapid changes has still to be understood. Adult echinoids play a crucial role in the tropical ecosystems where they live. Despite their role, few studies about the effect of temperature increase on their viability have been reported in literature. This thesis work reports a first systematic study on several Caribbean echinoids about their tolerance to temperature rise in the context of global warming. The research - carried out at the Bocas del Toro Station of the Smithsonian Tropical Research Institute, in Panama - focalized on the 6 sea urchins Lytechinus variegatus, L. williamsi, Echinometra lucunter, E. viridis, Tripneustes ventricosus and Eucidaris tribuloides, and the 2 sand dollars Clypeaster rosaceus and C. subdepressus. Mortality and neuromuscular well-being indicators - such as righting response, covering behaviour, adhesion to the substrate, spine and tube feet movements - have been analysed in the temperature range 28-38°C. The righting time RT (i.e., the time necessary for the animal to right itself completely after inversion) measured in the 6 sea urchin species, demonstrated a clearly dependence on the water temperature. The experiments allowed to determine the “thermal safety margin” (TSM) of each species. Echinometra lucunter and E. viridis resulted the most tolerant species to high temperatures with a TSM of 5.5°C, while T. ventricosus was the most vulnerable with a TSM of only 3°C. The study assessed that all the species already live at temperatures close to their upper thermal limit. Their TSMs are comparable to the predicted temperature increase by 2100. In absence of acclimatization to such temperature change, these species could experience severe die-offs, with important consequences for tropical marine ecosystems.

Effetti della defogliazione tardiva sulla composizione della bacca di Sangiovese (Vitis vinifera L.) in un vigneto biologico

In a context of climatic change, where high temperatures are frequent in the first phases of ripening, protecting bunches from solar radiation is essential to preserve berry colors. This thesis reports data collected in 2015 within a 3-year experiment conducted in Tebano (Faenza, Italy) in an organically-managed vineyard. Vines of cv Sangiovese submitted to post-veraison (15 Brix), pre-harvest late defoliation and post-veraison shoot positioning were compared with untreated controls. Treatments did not modify berry skin anthocyanins and flavonols, berry weight, soluble solids, pH, titratable acidity. Data are discussed in terms of the relevance of preserving berry skin anthocyanins and increasing berry skin flavonols through sustainable agronomic approaches for improving the color of young (co-pigmentation) and older (formation of polymeric pigments) wines. The benefits of late defoliations as an effective tool against Botrytis cluster rot are also discussed.

Studio della reattività del glicerol carbonato nella sintesi di derivati fenolici

Supported by the increasing sustainable awareness, glycerol carbonate has gained much interest over the last 20 years because of its versatile reactivity and as a way to valorize waste glycerol. Numerous synthesis pathways for this molecule were identified, some of them very promising and on the verge of being applied at an industrial scale. Here, we report a study aimed at valorizing glycerol carbonate as chemical intermediate, in order to synthesize 2-hydroxymethyl-1,4-benzodioxane (HMB). This molecule finds important applications as key intermediate for the synthesis of a broad class of pharmaceuticals and therapeutic agents. Concerning the presence of a stereogenic center on the hydroxymethyl group, due to the pharmaceutical importance to obtain and isolate one single enantiomer, , nowadays HMB is obtained through batch scale process, using a multi-reaction approach and starting from reagents of the chiral pool. We carried out the reaction from a solution of glycerol carbonate and catechol 2:1. In the presence of a simple basic catalyst, at high temperatures, it was possible obtain total reactants conversion and high yield to HMB in few hours reaction time. Also, in the aim of developing a process which might adhere the principles of Green Chemistry, we avoided the use of solvents. Similar results were obtained using a 1:1 feed ratio of reactants, even if selectivity to HMB decrease, due to the presence of side reactions. A complete study of the reaction mechanism is proposed in this thesis.