Investigation of gold-based catalysts for liquid phase oxidation of glucose to glucaric acid

Glucaric acid (GA) is one of the building block chemicals derived from sugar biomass with higher added value. Nowadays, GA is produced by oxidation of glucose (Glu) with either stoichiometric oxidants (HNO3), or by means of electrochemical or biochemical synthesis. However, these processes show drawbacks from either the environmental or economic viewpoint. For this reason, gold nanoparticles (Au NPs) supported on activated carbon (AC) have been studied as catalysts for the oxidation of Glu, using O2 as oxidant in the presence of a base. Using sol immobilization technique, Au NPs have been supported on AC following different experimental procedures. UV-Vis spectroscopy, XRD, TEM and TG analysis were utilized in the characterization of the catalysts. The operational conditions were optimized obtaining 24% of yield of GA, 37% to GO and 27% to byproducts in 1 h, 1000 rpm, 10 bar of O2 and Glu:Au:NaOH molar ratio of 1000:1:3000. Under such conditions, catalysts show relatively high Glu conversion (≥82%) with different GA yields. GO+GA yield is around 58-61%. Therefore, the oxidation reaction was performed at 15 min where Au/AC PVA0 reached the highest yield of GA (16%) and Au/AC PVA2.4 gave the lowest (8%). It is evident that the presence of PVA influences to a higher degree the reaction rate than the Au NPs size. Hence, the effect of different heat treatments where applied for the removal of PVA: washing with water at 60℃ or heat treatment (120-250℃) with Air/H2. Washing treatment and heat treatment at 120℃ with Air/H2 may have resulted in the mildest treatments for the removal of PVA. Finally, two different supports have been used in order to study the effect of metal-support interaction in the immobilization of Au NPs: ZrO2 and AC. Au/AC catalyst demonstrated a higher conversion of GO to GA at short reaction times (15.1% yield GA) compared to Au/ZrO2 (2.4% yield GA).

Theoretical and experimental studies of gold catalysts for glucose oxidation

The glucaric acid (GLA) has been identified as a “top value-added chemical from biomass” that can be employed for many uses; for instance, it could be a precursor of adipic acid, a monomer of Nylon-6,6. GLA can be synthetized by the oxidation of glucose (GLU), passing through the intermediate gluconic acid (GLO). In recent years, a new process has been sought to obtain GLA in an economic and environmental sustainable way, in order to replace the current use of HNO3 as a stoichiometric oxidant, or electrocatalysis and biochemical synthesis, which show several disadvantages. Thereby, this work is focused on the study of catalysts based on gold nanoparticles supported on activated carbon for the oxidation reaction of GLU to GLA using O2 as an oxidant agent and NaOH as base. The sol-immobilization method leads us to obtain small and well dispersed nanoparticles, characterized by UV-Vis, XRD and TEM techniques. Repeating the reaction on different batches of catalyst, both the synthesis and the reaction were confirmed to be reproducible. The effect of the reaction time feeding GLO as reagent was studied: the results show that the conversion of GLO increases as the reaction time increases; however, the yields of GLA and others increase up to 1 hour, and then they remain constant. In order to obtain information on the catalytic mechanism at the atomistic level, a computational study based on density functional theory and atomistic modeling of the gold nano-catalyst were performed. Highly symmetric (icosahedral and cubo-octahedral) and distorted Au55 nanoparticles have been optimized along with Au(111) and Au(100) surfaces. Distorted structures were found to be more stable than symmetrical ones due to relativistic effects. On these various models the adsorptions of various species involved in the catalysis have been studied, including OH- species, GLU and GLO. The study carried out aims to provide a method for approaching to the study of nanoparticellary catalytic systems.

Synthesis and characterisation of electrospun gold on ceria catalysts

Cerium oxide in catalysis can be used both as support and as a catalyst itself. Ceria catalyses many oxidations reactions, its excellent catalytic properties are due to its store oxygen storage capacity (OSC) and the reticular defects present on its surface. Different morphologies expose different reticular planes, and different reticular planes can expose different amounts of defects. The preparation method of cerium oxide can influence the surface area, morphology, and the number of defects in the sample. This work is focused on different preparation methods for gold nanoparticles supported on 1D nanostructures of cerium oxide prepared via electrospinning, their XRD, DRUV-Vis and Raman characterizations, and their catalytic performance on the oxidation reaction of HMF to FDCA.

N-Heterocyclic carbene complexes of silver, rhodium and iron: structures, dynamics and catalysis

The research performed in the framework of this Master Thesis has been directly inspired by the recent work of an organometallic research group led by Professor Maria Cristina Cassani on a topic related to the structures, dynamics and catalytic activity of N-heterocyclic carbene-amide rhodium(I) complexes1. A series of [BocNHCH2CH2ImR]X (R = Me, X = I, 1a’; R = Bz, X = Br, 1b’; R = trityl, X = Cl, 1c’) amide-functionalized imidazolium salts bearing increasingly bulky N-alkyl substituents were synthetized and characterized. Subsequently, these organic precursors were employed in the synthesis of silver(I) complexes as intermediate compounds on a way to rhodium(I) complexes [Rh(NBD)X(NHC)] (NHC = 1-(2-NHBoc-ethyl)-3-R-imidazolin-2-ylidene; X = Cl, R = Me (3a’), R = Bz (3b’), R = trityl (3c’); X = I, R = Me (4a’)). VT NMR studies of these complexes revealed a restricted rotation barriers about the metal-carbene bond. However, while the rotation barriers calculated for the complexes in which R = Me, Bz (3a’,b’ and 4a) matched the experimental values, this was not true in the trityl case 3c’, where the experimental value was very similar to that obtained for compound 3b’ and much smaller with respect to the calculated one. In addition, the energy barrier derived for 3c’ from line shape simulation showed a strong dependence on the temperature, while the barriers measured for 3a’,b’ did not show this effect. In view of these results and in order to establish the reasons for the previously found inconsistency between calculated and experimental thermodynamic data, the first objective of this master thesis was the preparation of a series of rhodium(I) complexes [Rh(NBD)X(NHC)] (NHC = 1-benzyl-3-R-imidazolin-2-ylidene; X = Cl, R = Me, Bz, trityl, tBu), containing the benzyl substituent as a chiral probe, followed by full characterization. The second objective of this work was to investigate the catalytic activity of the new rhodium compounds in the hydrosilylation of terminal alkynes for comparison purposes with the reported complexes. Another purpose of this work was to employ the prepared N-heterocyclic ligands in the synthesis of iron(II)-NHC complexes.

Studio di nuovi processi catalitici per la sintesi di acido adipico

L’acido adipico (AA) è un importante intermedio chimico prodotto in quantità pari a circa tre milioni di tonnellate annue, i cui usi riguardano principalmente la produzione di Nylon-6,6. Tutti i processi industriali odierni per la produzione dell’AA hanno in comune lo stadio finale di ossidazione con acido nitrico dell’ultimo intermedio di sintesi, che in genere è una miscela di cicloesanolo e cicloesanone (KA Oil). Esistono diversi problemi riguardanti questo processo, come la pericolosità che deriva dall’uso di acido nitrico concentrato. Dal punto di vista ambientale, il problema principale riguarda la produzione di protossido di azoto e di altri ossidi di azoto durante l’ultima fase di ossidazione con HNO3, per questo motivo, tutte le aziende che producono AA devono essere munite per legge di sistemi di abbattimento quantitativi o di recupero degli ossidi di azoto, che però risultano essere molto incisivi sul costo del processo. A livello industriale, quindi, il problema riguarda principalmente la sostenibilità economica, ma poiché queste procedure hanno un prezzo in termini di materiali ed energia, si ha anche un forte legame con la sostenibilità ambientale. Gli studi riguardanti nuovi processi per la produzione di AA sono numerosi; alcuni hanno portato a vie più “green”, ma solo pochi esempi sono veramente sostenibili dal punto di vista sia ambientale che economico. Il presente lavoro di tesi è diviso in due parti, entrambe riguardanti vie di sintesi alternative per la produzione di AA. La prima parte riguarda lo studio del secondo passaggio di una via di sintesi in due step che parte da cicloesene e che ha come intermedio l’1,2-cicloesandiolo.Sono stati provati catalizzatori eterogenei a base di nanoparticelle di Au supportate su MgO per il cleavage ossidativo in fase liquida del diolo con O2 in ambiente basico. La seconda parte invece riguarda il processo di sintesi dell’AA a partire da cicloesanone mediante l’ossidazione con perossido di idrogeno a e- caprolattone e la successiva ossidazione ad AA. Nello specifico, è stato studiato il meccanismo di reazione del primo passaggio in quanto evidenze sperimentali ottenute nel corso di lavori precedenti avevano dimostrato la presenza di un cammino di reazione differente da quello tipico per un’ossidazione di Baeyer-Villiger. In questa parte, si è studiato l’effetto di alcuni catalizzatori eterogenei a base di acidi di Lewis sui prodotti ottenuti nel primo stadio ossidativo.

Organic/inorganic polyoxometalate-based hybrids for oxidation catalysis and energy conversion

This thesis work has been carried out during the Erasmus exchange period at the “Université Paris 6 – Pierre et Marie Curie”, in the “Edifices PolyMétalliques – EPOM” team, leaded by Prof. Anna Proust, belonging to the “Institut Parisien de Chimie Moléculaire”, under the supervision of Dr. Guillaume Izzet and Dr. Geoffroy Guillemot. The redox properties of functionalized Keggin and Dawson POMs have been exploited in photochemical, catalytic and reactivity tests. For the photochemical purposes, the selected POMs have been functionalized with different photoactive FGs, and the resulting products have been characterized by CV analyses, luminescence tests and UV-Vis analyses. In future, these materials will be tested for hydrogen photoproduction and polymerization of photoactive films. For the catalytic purposes, POMs have been firstly functionalized with silanol moieties, to obtain original coordination sites, and then post-functionalized with TMs such as V, Ti and Zr in their highest oxidation states. In this way, the catalytic properties of TMs were coupled to the redox properties of POM frameworks. The redox behavior of some of these hybrids has been studied by spectro-electrochemical and EPR methods. Catalytic epoxidation tests have been carried out on allylic alcohols and n-olefins, employing different catalysts and variable amounts of them. The performances of POM-V hybrids have been compared to those of VO(iPrO)3. Finally, reactivity of POM-VIII hybrids has been studied, using styrene oxide and ethyl-2-diazoacetate as substrates. All the obtained products have been analyzed via NMR techniques. Cyclovoltammetric analyses have been carried out in order to determine the redox behavior of selected hybrids.

Studio di validità concorrente tra sistema indossabile basato su IMU e stereofotogrammetria usata come gold standard

L’analisi della postura e del movimento umano costituiscono un settore biomedico in forte espansione e di grande interesse dal punto di vista clinico. La valutazione delle caratteristiche della postura e del movimento, nonché delle loro variazioni rispetto ad una situazione di normalità, possono essere di enorme utilità in campo clinico per la diagnosi di particolari patologie, così come per la pianificazione ed il controllo di specifici trattamenti riabilitativi. In particolare è utile una valutazione quantitativa della postura e del movimento che può essere effettuata solo utilizzando metodologie e tecnologie ‘ad hoc’. Negli ultimi anni la diffusione di sensori MEMS e lo sviluppo di algoritmi di sensor fusion hanno portato questi dispositivi ad entrare nel mondo della Motion Capture. Queste piattaforme multi-sensore, comunemente chiamate IMU (Inertial Measurement Unit), possono rappresentare l’elemento base di una rete sensoriale per il monitoraggio del movimento umano.