The contribution of the Finite Volume Point Dilution Method to the determination of solute mass flux in an alluvial aquifer.

Groundwater represents one of the most important resources of the world and it is essential to prevent its pollution and to consider remediation intervention in case of contamination. According to the scientific community the characterization and the management of the contaminated sites have to be performed in terms of contaminant fluxes and considering their spatial and temporal evolution. One of the most suitable approach to determine the spatial distribution of pollutant and to quantify contaminant fluxes in groundwater is using control panels. The determination of contaminant mass flux, requires measurement of contaminant concentration in the moving phase (water) and velocity/flux of the groundwater. In this Master Thesis a new solute flux mass measurement approach, based on an integrated control panel type methodology combined with the Finite Volume Point Dilution Method (FVPDM), for the monitoring of transient groundwater fluxes, is proposed. Moreover a new adsorption passive sampler, which allow to capture the variation of solute concentration with time, is designed. The present work contributes to the development of this approach on three key points. First, the ability of the FVPDM to monitor transient groundwater fluxes was verified during a step drawdown test at the experimental site of Hermalle Sous Argentau (Belgium). The results showed that this method can be used, with optimal results, to follow transient groundwater fluxes. Moreover, it resulted that performing FVPDM, in several piezometers, during a pumping test allows to determine the different flow rates and flow regimes that can occurs in the various parts of an aquifer. The second field test aiming to determine the representativity of a control panel for measuring mass flus in groundwater underlined that wrong evaluations of Darcy fluxes and discharge surfaces can determine an incorrect estimation of mass fluxes and that this technique has to be used with precaution. Thus, a detailed geological and hydrogeological characterization must be conducted, before applying this technique. Finally, the third outcome of this work concerned laboratory experiments. The test conducted on several type of adsorption material (Oasis HLB cartridge, TDS-ORGANOSORB 10 and TDS-ORGANOSORB 10-AA), in order to determine the optimum medium to dimension the passive sampler, highlighted the necessity to find a material with a reversible adsorption tendency to completely satisfy the request of the new passive sampling technique.

Processes influencing the nitrate concentration in an aquifer for drinking water production in Bremen-Nord - Northern Germany

Groundwater represents the most important raw material. Germany struggles to maintain the best water quality possible by providing advanced monitoring systems and legal measures to prevent further pollution. In areas involved in the intensive growing of plantations, one of the major contamination factors derives from nitrate. The aim of this master thesis is the characterisation of the Water Protection Area of Bremen (Germany). Denitrification is a natural process, representing the best means of natural reduction of the hazardous nitrate ion, which is dangerous both for human health and for the development of eutrophication. The study has been possible thanks to the collaboration with the University of Bremen, the Geological Service of Bremen (GDfB) and Peter Spiedt (Water Supply Company of Bremen). It will be defined whether nitrate amounts in the groundwater still overcome the threshold legally imposed, and state if the denitrification process takes place, thanks to new samples collected in 2015 and their integration with historical data. Gas samples have been gathered to test them with the “N2/Ar method”, which is able to estimate the denitrification rate quantitatively. Analyses stated the effective occurrence of the reaction, nevertheless showing that it only affects the chemical of the deep aquifers and not shallow ones. Temporal trends concentrations of nitrate have shown that no real improvement took place in the past years. It will be commented that despite the denitrification being responsible for an efficacious lowering in the nitrate ion, it needs reactive materials to take place. Since the latter are finite elements, it is not an endless process. It is thus believed that is clearly necessary to adopt a better attitude in order to maintain the best chemical qualities possible in such an important area, providing drinking water.

Bioremediation of PAHs - Limitations and soultions

Introduction 1.1 Occurrence of polycyclic aromatic hydrocarbons (PAH) in the environment Worldwide industrial and agricultural developments have released a large number of natural and synthetic hazardous compounds into the environment due to careless waste disposal, illegal waste dumping and accidental spills. As a result, there are numerous sites in the world that require cleanup of soils and groundwater. Polycyclic aromatic hydrocarbons (PAHs) are one of the major groups of these contaminants (Da Silva et al., 2003). PAHs constitute a diverse class of organic compounds consisting of two or more aromatic rings with various structural configurations (Prabhu and Phale, 2003). Being a derivative of benzene, PAHs are thermodynamically stable. In addition, these chemicals tend to adhere to particle surfaces, such as soils, because of their low water solubility and strong hydrophobicity, and this results in greater persistence under natural conditions. This persistence coupled with their potential carcinogenicity makes PAHs problematic environmental contaminants (Cerniglia, 1992; Sutherland, 1992). PAHs are widely found in high concentrations at many industrial sites, particularly those associated with petroleum, gas production and wood preserving industries (Wilson and Jones, 1993). 1.2 Remediation technologies Conventional techniques used for the remediation of soil polluted with organic contaminants include excavation of the contaminated soil and disposal to a landfill or capping - containment - of the contaminated areas of a site. These methods have some drawbacks. The first method simply moves the contamination elsewhere and may create significant risks in the excavation, handling and transport of hazardous material. Additionally, it is very difficult and increasingly expensive to find new landfill sites for the final disposal of the material. The cap and containment method is only an interim solution since the contamination remains on site, requiring monitoring and maintenance of the isolation barriers long into the future, with all the associated costs and potential liability. A better approach than these traditional methods is to completely destroy the pollutants, if possible, or transform them into harmless substances. Some technologies that have been used are high-temperature incineration and various types of chemical decomposition (for example, base-catalyzed dechlorination, UV oxidation). However, these methods have significant disadvantages, principally their technological complexity, high cost , and the lack of public acceptance. Bioremediation, on the contrast, is a promising option for the complete removal and destruction of contaminants. 1.3 Bioremediation of PAH contaminated soil & groundwater Bioremediation is the use of living organisms, primarily microorganisms, to degrade or detoxify hazardous wastes into harmless substances such as carbon dioxide, water and cell biomass Most PAHs are biodegradable unter natural conditions (Da Silva et al., 2003; Meysami and Baheri, 2003) and bioremediation for cleanup of PAH wastes has been extensively studied at both laboratory and commercial levels- It has been implemented at a number of contaminated sites, including the cleanup of the Exxon Valdez oil spill in Prince William Sound, Alaska in 1989, the Mega Borg spill off the Texas coast in 1990 and the Burgan Oil Field, Kuwait in 1994 (Purwaningsih, 2002). Different strategies for PAH bioremediation, such as in situ , ex situ or on site bioremediation were developed in recent years. In situ bioremediation is a technique that is applied to soil and groundwater at the site without removing the contaminated soil or groundwater, based on the provision of optimum conditions for microbiological contaminant breakdown.. Ex situ bioremediation of PAHs, on the other hand, is a technique applied to soil and groundwater which has been removed from the site via excavation (soil) or pumping (water). Hazardous contaminants are converted in controlled bioreactors into harmless compounds in an efficient manner. 1.4 Bioavailability of PAH in the subsurface Frequently, PAH contamination in the environment is occurs as contaminants that are sorbed onto soilparticles rather than in phase (NAPL, non aqueous phase liquids). It is known that the biodegradation rate of most PAHs sorbed onto soil is far lower than rates measured in solution cultures of microorganisms with pure solid pollutants (Alexander and Scow, 1989; Hamaker, 1972). It is generally believed that only that fraction of PAHs dissolved in the solution can be metabolized by microorganisms in soil. The amount of contaminant that can be readily taken up and degraded by microorganisms is defined as bioavailability (Bosma et al., 1997; Maier, 2000). Two phenomena have been suggested to cause the low bioavailability of PAHs in soil (Danielsson, 2000). The first one is strong adsorption of the contaminants to the soil constituents which then leads to very slow release rates of contaminants to the aqueous phase. Sorption is often well correlated with soil organic matter content (Means, 1980) and significantly reduces biodegradation (Manilal and Alexander, 1991). The second phenomenon is slow mass transfer of pollutants, such as pore diffusion in the soil aggregates or diffusion in the organic matter in the soil. The complex set of these physical, chemical and biological processes is schematically illustrated in Figure 1. As shown in Figure 1, biodegradation processes are taking place in the soil solution while diffusion processes occur in the narrow pores in and between soil aggregates (Danielsson, 2000). Seemingly contradictory studies can be found in the literature that indicate the rate and final extent of metabolism may be either lower or higher for sorbed PAHs by soil than those for pure PAHs (Van Loosdrecht et al., 1990). These contrasting results demonstrate that the bioavailability of organic contaminants sorbed onto soil is far from being well understood. Besides bioavailability, there are several other factors influencing the rate and extent of biodegradation of PAHs in soil including microbial population characteristics, physical and chemical properties of PAHs and environmental factors (temperature, moisture, pH, degree of contamination). Figure 1: Schematic diagram showing possible rate-limiting processes during bioremediation of hydrophobic organic contaminants in a contaminated soil-water system (not to scale) (Danielsson, 2000). 1.5 Increasing the bioavailability of PAH in soil Attempts to improve the biodegradation of PAHs in soil by increasing their bioavailability include the use of surfactants , solvents or solubility enhancers.. However, introduction of synthetic surfactant may result in the addition of one more pollutant. (Wang and Brusseau, 1993).A study conducted by Mulder et al. showed that the introduction of hydropropyl-ß-cyclodextrin (HPCD), a well-known PAH solubility enhancer, significantly increased the solubilization of PAHs although it did not improve the biodegradation rate of PAHs (Mulder et al., 1998), indicating that further research is required in order to develop a feasible and efficient remediation method. Enhancing the extent of PAHs mass transfer from the soil phase to the liquid might prove an efficient and environmentally low-risk alternative way of addressing the problem of slow PAH biodegradation in soil.

Idrologia di un cordone di dune costiere nella zona naturale a sud di Foce Bevano

Dalla collaborazione fra il Comune di Ravenna ed ENI ha preso origine il progetto “RIGED – Ra” ossia il “Progetto di ripristino e gestione delle dune costiere ravennati”. Nell’ambito di tale attività sperimentale si è voluto effettuare una caratterizzazione dell’idrologia di una limitata, ma rappresentativa, porzione dell’acquifero freatico costiero situata in un cordone di dune posto nella Pineta di Lido di Classe, a sud di Foce Bevano. Lo studio si pone di essere rappresentativo per le caratteristiche idrogeologiche delle dune costiere adriatiche nella zona di Ravenna. A tale fine è stato valutato l’andamento di alcuni parametri chimico-fisici delle acque sotterranee; inoltre, è stata monitorata mensilmente la profondità della tavola d’acqua (water table - WT). Questi monitoraggi hanno permesso di descrivere la distribuzione delle acque dolci e di quelle salate nonché la loro dinamica stagionale. Infine, è stata eseguita un’analisi idro-geochimica con l’intento di valutare la tipologia delle acque presenti nell’area in esame e la loro eventuale variazione stagionale. Per la raccolta dei campioni è stata sfruttata l’innovativa metodologia a minifiltri utilizzata da alcuni anni nel nord dell’Europa, in modo particolare in Olanda. Questa tecnica ha due caratteristiche peculiari: i tempi di campionamento vengono ridotti notevolmente ed, inoltre, permette un’ottima precisione e rappresentatività delle acque di falda a diverse profondità poiché si effettua un campionamento ogni 0,50 m. L’unico limite riscontrato, al quale vi è comunque rimedio, è il fatto che la loro posizione risulti fissa per cui, qualora vi siano delle fluttuazioni dell’acquifero al di sopra del minifiltro più superficiale, queste non vengono identificate. È consigliato quindi utilizzare questo metodo di campionamento poiché risulta essere più performante rispetto ad altri (ad esempio al sistema che sfrutta lo straddle packers SolinstTM ) scegliendo tra due diverse strategie per rimediare al suo limite: si aggiungono minifiltri superficiali che nel periodo estivo si trovano nella zona vadosa dell’acquifero oppure si accompagna sempre il campionamento con una trivellata che permetta il campionamento del top della falda. Per quanto concerne la freatimetria il campionamento mensile (6 mesi) ha mostrato come tutta l’area di studio sia un sistema molto suscettibile all’andamento delle precipitazioni soprattutto per la fascia di duna prossima alla costa in cui la scarsa vegetazione e la presenza di sedimento molto ben cernito con una porosità efficace molto elevata facilitano la ricarica dell’acquifero da parte di acque dolci. Inoltre, sul cordone dunoso l’acquifero si trova sempre al di sopra del livello medio mare anche nel periodo estivo. Per questa caratteristica, nel caso l’acquifero venisse ricaricato artificialmente con acque dolci (Managed Aquifer Recharge), potrebbe costituire un efficace sistema di contrasto all’intrusione salina. Lo spessore d’acqua dolce, comunque, è molto variabile proprio in funzione della stagionalità delle precipitazioni. Nell’area retro-dunale, invece, nel periodo estivo l’acquifero freatico è quasi totalmente al di sotto del livello marino; ciò probabilmente è dovuto al fatto che, oltre ai livelli topografici prossimi al livello medio mare, vi è una foltissima vegetazione molto giovane, ricresciuta dopo un imponente incendio avvenuto circa 10 anni fa, la quale esercita una notevole evapotraspirazione. È importante sottolineare come durante la stagione autunnale, con l’incremento delle precipitazioni la tavola d’acqua anche in quest’area raggiunga livelli superiori a quello del mare. Dal monitoraggio dei parametri chimico – fisici, in particolare dal valore dell’Eh, risulta che nel periodo estivo l’acquifero è un sistema estremamente statico in cui la mancanza di apporti superficiali di acque dolci e di flussi sotterranei lo rende un ambiente fortemente anossico e riducente. Con l’arrivo delle precipitazioni la situazione cambia radicalmente, poiché l’acquifero diventa ossidante o lievemente riducente. Dalle analisi geochimiche, risulta che le acque sotterranee presenti hanno una composizione esclusivamente cloruro sodica in entrambe le stagioni monitorate; l’unica eccezione sono i campioni derivanti dal top della falda raccolti in gennaio, nei quali la composizione si è modificata in quanto, il catione più abbondante rimane il sodio ma non si ha una dominanza di un particolare anione. Tale cambiamento è causato da fenomeni di addolcimento, rilevati dall’indice BEX, che sono causati all’arrivo delle acque dolci meteoriche. In generale, si può concludere che la ricarica superficiale e la variazione stagionale della freatimetria non sono tali da determinare un processo di dolcificazione in tutto l’acquifero dato che, nelle zone più profonde, si rivela la presenza permanente di acque a salinità molto superiore a 10 g/L. La maggior ricarica superficiale per infiltrazione diretta nelle stagioni a più elevata piovosità non è quindi in grado di approfondire l’interfaccia acqua dolce-acqua salata e può solamente causare una limitata diluizione delle acque di falda superficiali.

Hydrogeochemical characterization of Seehausen territory - Bremen

The aim of this thesis is to provide a geochemical characterization of the Seehausen territory (a neighborhood) of Bremen, Germany. In this territory it is hosted a landfill of dredged sediments coming both from Bremerhaven (North See) and Bremen harbor (directly on the river Weser). For this reason this work has been focused also on possible impacts of the landfill on the groundwaters (shallow and deep aquifer). The Seehausen landfill uses the dewatering technique to manage the dredged sediments: incoming sediments are put into dewatering fields until they are completely dried (it takes almost a year). Then they are randomly sampled and analyzed: if the pollutants content is acceptable, sediments are treated with other materials and used instead of raw material for embankment, bricks, etc., otherwise they are disposed in the landfill. During this work it has been made a study of the natural geology and hydrogeology of the whole area of interest, especially because it is characterized by ancient natural salt deposits. Then, together with the Geological Survey of Bremen and the Harbor Authority of Bremen there have been identified all useful piezometers for a monitoring net around the landfill. During the sampling campaign there have been collected data of the principal anions and cations, physical parameters and stable water isotopes. Data analysis has been focused particularly on Cl, Na, SO4 and EC because these parameters might be helpful to attribute geochemical trends to the landfill or to a natural background. Furthermore dataloggers have been installed for a month in some piezometers and EC, pressure, dissolved oxygen and temperature data have been collected. Finally there has been made a deep comparison between current and historical data (1996 – 2011) and between old interpolation maps and current ones in order to see time trends of the aquifer geochemistry.

Analisi idrogeologica dell'area carsica dei Monti Alburni (Salerno, Campania)

The Alburni Massif is the most important karstic area in southern Italy and It contains about 250 caves. Most of these caves are located on the plateau, between 1500 m a.s.l. and 700 m a.s.l., and only a few reach the underground streams that feed the springs and the deep aquifer. The main springs are Grotta di Pertosa-Auletta (CP1) and Auso spring (CP31), both located at 280 m a.s.l., the first on the south-eastern margin whereas the second on south-west margin, and the springs present in Castelcivita area, the Castelcivita-Ausino system (CP2) and Mulino di Castelcivita spring (CP865), located at 60 m a.s.l.. Some other secondary springs are present too. We have monitored Pertosa-Auletta’s spring with a multiparameter logger. This logger has registered data from November 2014 to December 2015 regarding water level, electric conductivity and temperature. The hydrodynamic monitoring has been supported by a sampling campaign in order to obtain chemical water analyses. The work was done from August 2014 to December 2015, not only at Pertosa but also at all the other main springs, and in some caves. It was possible to clarify the behavior of Pertosa-Auletta’s spring, almost exclusively fed by full charge conduits, only marginally affected by seasonal rains. Pertosa-Auletta showed a characteristic Mg/Ca ratio and Mg2+ enrichment, as demonstrated by its saturation index that always showed a dolomite saturation. All other spring have characteristic waters from a chemical point of view. In particular, it highlights the great balance between the components dissolved in the waters of Mulino’ spring opposed to the variability of the nearby Castelcivita-Ausino spring. Regarding the Auso spring the variable behavior in terms of discharge and chemistry is confirmed, greatly influenced by rainfall and, during drought periods, by full charge conduits. Rare element concentrations were also analyzed and allowed to characterize further the different waters. Based on all these data an updated hydrogeological map of the Alburni massif has been drawn, that defines in greater detail the hydrogeological complexes on the basis of lithologies, and therefore of their chemical characteristics.