Multi-mode communications in near field exploiting OAM properties

This dissertation analyzes the exploitation of the orbital angular momentum (OAM) of the electromagnetic waves with large intelligent surfaces in the near-field region and line-of-sight conditions, in light of the holographic MIMO communication concept. Firstly, a characterization of the OAM-based communication problem is presented, and the relationship between OAM-carrying waves and communication modes is discussed. Then, practicable strategies for OAM detection using large intelligent surfaces and optimization methods based on beam focusing are proposed. Numerical results characterize the effectiveness of OAM with respect to other strategies, also including the proposed detection and optimization methods. It is shown that OAM waves constitute a particular choice of communication modes, i.e., an alternative basis set, which is sub-optimum with respect to optimal basis functions that can be derived by solving eigenfunction problems. Moreover, even the joint utilization of OAM waves with focusing strategies led to the conclusion that no channel capacity achievements can be obtained with these transmission techniques.

Economic and Environmental Optimization of Ornamental Stone Block Cutting with a 3D Algorithm

This thesis focuses on finding the optimum block cutting dimensions in terms of the environmental and economic factors by using a 3D algorithm for a limestone quarry in Foggia, Italy. The environmental concerns of quarrying operations are mainly: energy consumption, material waste, and pollution. The main economic concerns are the block recovery, the selling prices, and the production costs. Fractures adversely affect the block recovery ratio. With a fracture model, block production can be optimized. In this research, the waste volume produced by quarrying was minimised to increase the recovery ratio and ensure economic benefits. SlabCutOpt is a software developed at DICAM–University of Bologna for block cutting optimization which tests different cutting angles on the x-y-z planes to offer up alternative cutting methods. The program tests several block sizes and outputs the optimal result for each entry. By using SlabCutOpt, ten different block dimensions were analysed, the results indicated the maximum number of non-intersecting blocks for each dimension. After analysing the outputs, the block named number 1 with the dimensions ‘1mx1mx1m’ had the highest recovery ratio as 43% and the total Relative Money Value (RMV) with a value of 22829. Dimension number 1, also had the lowest waste volume, with a value of 3953.25 m3, for the total bench. For cutting the total bench volume of 6932.25m3, the diamond wire cutter had the lowest dust emission values for the block with the dimension ‘2mx2mx2m’, with a value of 24m3. When compared with the Eco-Label standards, block dimensions having surface area values lower than 15m2, were found to fit the natural resource waste criteria of the label, as the threshold required 25% of minimum recovery [1]. Due to the relativity of production costs, together with the Eco-Label threshold, the research recommends the selection of the blocks with a surface area value between 6m2 and 14m2.

Tolerance optimization with statistical approach in the CAT environment

Nowadays, product development in all its phases plays a fundamental role in the industrial chain. The need for a company to compete at high levels, the need to be quick in responding to market demands and therefore to be able to engineer the product quickly and with a high level of quality, has led to the need to get involved in new more advanced methods/ processes. In recent years, we are moving away from the concept of 2D-based design and production and approaching the concept of Model Based Definition. By using this approach, increasingly complex systems turn out to be easier to deal with but above all cheaper in obtaining them. Thanks to the Model Based Definition it is possible to share data in a lean and simple way to the entire engineering and production chain of the product. The great advantage of this approach is precisely the uniqueness of the information. In this specific thesis work, this approach has been exploited in the context of tolerances with the aid of CAD / CAT software. Tolerance analysis or dimensional variation analysis is a way to understand how sources of variation in part size and assembly constraints propagate between parts and assemblies and how that range affects the ability of a project to meet its requirements. It is critically important to note how tolerance directly affects the cost and performance of products. Worst Case Analysis (WCA) and Statistical analysis (RSS) are the two principal methods in DVA. The thesis aims to show the advantages of using statistical dimensional analysis by creating and examining various case studies, using PTC CREO software for CAD modeling and CETOL 6σ for tolerance analysis. Moreover, it will be provided a comparison between manual and 3D analysis, focusing the attention to the information lost in the 1D case. The results obtained allow us to highlight the need to use this approach from the early stages of the product design cycle.

Axis control optimization: autotuning techniques and frequency response analysis of industrial mechatronic systems

In the field of industrial automation, there is an increasing need to use optimal control systems that have low tracking errors and low power and energy consumption. The motors we are dealing with are mainly Permanent Magnet Synchronous Motors (PMSMs), controlled by 3 different types of controllers: a position controller, a speed controller, and a current controller. In this thesis, therefore, we are going to act on the gains of the first two controllers by going to find, through the TwinCAT 3 software, what might be the best set of parameters. To do this, starting with the default parameters recommended by TwinCAT, two main methods were used and then compared: the method of Ziegler and Nichols, which is a tabular method, and advanced tuning, an auto-tuning software method of TwinCAT. Therefore, in order to analyse which set of parameters was the best,several experiments were performed for each case, using the Motion Control Function Blocks. Moreover, some machines, such as large robotic arms, have vibration problems. To analyse them in detail, it was necessary to use the Bode Plot tool, which, through Bode plots, highlights in which frequencies there are resonance and anti-resonance peaks. This tool also makes it easier to figure out which and where to apply filters to improve control.