Fracture toughness characterization of aluminium-epoxy adhesive joints reinforced with electrospun Nylon 6,6 nanofibers

The use of adhesives to join two different substrates is an efficient replacement to classic joining technologies such as welding and soldering. One the one hand adhesion has different advantages over those techniques such as an improved stress distribution and the potential weight reduction of the structure; on the other hand, two of the most important drawbacks are a relatively low fracture toughness and the need of an accurate surface preparation. These two aspects will be accurately analysed in the present work: the use of Nylon nanofibers as reinforcement for the adhesive should increase fracture toughness, while a surface preparation method consisting of mechanical and chemical treatments will be developed. After the specimens are produced, they will be tested in mode I fracture using a DCB (Double Beam Cantilever) test, which allows to measure the fracture toughness during crack propagation. At the end of the test, the surfaces of the adherends will be visually observed and SEM (Scanning Electronic Microscope) analysed in order to evaluate if adhesive or cohesive fracture occurred, and thus if surface treatments has been well developed to allow a better adhesive-aluminium joining.

On the influence of polymeric nanofibers in laminated composite materials. Studio dell'influenza di nanofibre polimeriche in materiali compositi laminati

During the last years an increased interest about the reinforcement of laminated composites by means of polymeric nanofibers has been growth. During this master-degree-thesis work, unidirectional and plane-textile composites have been interleaved with Nylon 6.6, PCL and mixed (Nylon 6.6+PCL) nanofibrous mats and the DCB (mode I interlaminar fracture toughness), ENF (mode II interlaminar fracture toughness and DMA (damping capability) tests have been performed. Regarding the interlaminar fracture toughness, marked increases have been recorded; while further investigation about damping capability is requested.

Electrospun scaffolds for regeneration of musculoskeletal interface tissues

L’apparato muscolo scheletrico è composto da strutture muscolari, articolari e ossee. Tali tessuti sono molto diversi tra loro e hanno proprietà meccaniche estremamente variabili, pertanto presentano una transizione graduale in corrispondenza della loro giunzione, onde evitare l’insorgere di concentrazioni di tensione. L’evoluzione ha portato alla formazione di particolari interfacce che permettono la corretta trasmissione dei carichi distribuendo le tensioni su una superficie più ampia in corrispondenza della giunzione. Le interfacce che vanno a inserirsi nell’osso vengono definite entesi e in particolare, in questa review, analizzeremo il caso di quelle tra tendini/legamenti e osso. In questo lavoro ci siamo anche concentrati sulla giunzione miotendinea, ovvero tra muscolo e tendine. Sono numerose le lesioni che riguardano muscoli, ossa, tendini o legamenti e molto spesso l’infortunio avviene a livello della giunzione. Quando ciò accade vi sono diverse strade, ciascuna con i suoi vantaggi e svantaggi: sutura, autograft, allograft o xenograft. Oltre a queste soluzioni si è fatta gradualmente più spazio la possibilità di realizzare degli scaffold che vadano temporaneamente a sostituire la parte danneggiata e a promuovere la sua rigenerazione, degradandosi man mano. L’elettrofilatura (Elettrospinning) è un processo produttivo che negli ultimi decenni si è affermato come tecnica per la fabbricazione di questi scaffold, fino a diventare uno tra i principali processi utilizzati dai ricercatori in questo campo. Questa tecnica infatti permette di realizzare scaffold di nanofibre porose utilizzando polimeri biodegradabili e soprattutto biocompatibili. Lo scopo della review è proprio quello di scoprire tutti i lavori e gli studi che utilizzano l’elettrofilatura per realizzare degli scaffold per interfacce, delineando così lo stato dell’arte sui progressi fatti e sulle varie tecniche utilizzate.

Damping and Thermomechanical behaviour of CFRP laminates modified with rubbery nanofibers

Nanofibrous membranes are a promising material for tailoring the properties of laminated CFRP composites by embedding them into the structure. This project aimed to understand the effect of number, position and thickness of nanofibrous modifications specifically on the damping behaviour of the resulting nano-modified CFRP composite with an epoxy matrix. An improvement of damping capacity is expected to improve a composites lifetime and fatigue resistance by prohibiting the formation of microcracks and consequently hindering delamination, it also promises a rise in comfort for a range of final products by intermission of vibration propagation and therefore diminution of noise. Electrospinning was the technique employed to produce nanofibrous membranes from a blend of polymeric solutions. SEM, WAXS and DSC were utilised to evaluate the quality of the obtained membranes before they were introduced, following a specific stacking sequence, in the production process of the laminate. A suitable curing cycle in an autoclave was applied to mend the modifications together with the matrix material, ensuring full crosslinking of the matrix and therefore finalising the production process. DMA was exercised in order to gain an understanding about the effects of the different modifications on the properties of the composite. During this investigation it became apparent that a high number of modifications of laminate CFRP composites, with an epoxy matrix, with thick rubbery nanofibrous membranes has a positive effect on the damping capacity and the temperature range the effect applies in. A suggestion for subsequent studies as well as a recommendation for the production of nano-modified CFRP structures is included at the end of this document.

Synthesis and characterisation of electrospun gold on ceria catalysts

Cerium oxide in catalysis can be used both as support and as a catalyst itself. Ceria catalyses many oxidations reactions, its excellent catalytic properties are due to its store oxygen storage capacity (OSC) and the reticular defects present on its surface. Different morphologies expose different reticular planes, and different reticular planes can expose different amounts of defects. The preparation method of cerium oxide can influence the surface area, morphology, and the number of defects in the sample. This work is focused on different preparation methods for gold nanoparticles supported on 1D nanostructures of cerium oxide prepared via electrospinning, their XRD, DRUV-Vis and Raman characterizations, and their catalytic performance on the oxidation reaction of HMF to FDCA.