Heave of large excavations in clay: modelling and analysis of two british case-histories

ABSTRACT Il presente lavoro vuole introdurre la problematica del rigonfiamento del terreno a seguito di grandi scavi in argilla. Il sollevamento del terreno dopo lo scavo può passare inosservato ma sono numerosi i casi in cui il rigonfiamento dura per molti anni e addirittura decenni, Shell Centre, London, Lion Yard, Cambridge, Bell Common, London, ecc. Questo rigonfiamento il più delle volte è impedito dalla presenza di fondazioni, si genera quindi una pressione distribuita che se non considerata in fase di progetto può portare alla fessurazione della fondazione stessa. L’anima del progetto è la modellazione e l’analisi del rigonfiamento di grandi scavi in argilla, confrontando poi i risultati con i dati reali disponibili in letteratura. L’idea del progetto nasce dalla difficoltà di ottenere stime e previsioni attendibili del rigonfiamento a seguito di grandi scavi in argilla sovraconsolidata. Inizialmente ho esaminato la teoria e i fattori che influenzano il grado e la velocità del rigonfiamento, quali la rigidezza, permeabilità, fessurazione, struttura del suolo, etc. In seguito ho affrontato lo studio del comportamento rigonfiante di argille sovraconsolidate a seguito di scarico tensionale (scavi), si è evidenziata l’importanza di differenziare il rigonfiamento primario e il rigonfiamento secondario dovuto al fenomeno del creep. Il tema centrale del progetto è l’analisi numerica tramite Flac di due grandi scavi in argilla, Lion Yard, Cambridge, e, Bell Common, London. Attraverso una dettagliata analisi parametrica sono riuscito a trovare i migliori parametri che modellano il comportamento reale nei due casi in esame, in questo modo è possibile arrivare a stime e previsioni attendibili del fenomeno rigonfiante del terreno a seguito di grandi scavi. Gli scavi modellati Lion Yard e Bell Common sono rispettivamente in Gault Clay e London Clay, grazie a famosi recenti articoli scientifici sono riuscito a evidenziare la principali propietà che diversificano i due terreni in esame, tali propietà sono estremamente differenti dalle normali caratteristiche considerate per la progettazione in presenza di terreno argilloso; sono così riuscito a implementare i migliori parametri per descrivere il comportamento dei due terreni nei diversi modelli. Ho inoltre studiato l’interazione terreno-struttura, la pressione esercitata dal rigonfiamento del terreno è strettamente funzione delle caratteristiche di connesione tra fondazione superficiale e muro di sostegno, tale pressione non deve essere ignorata in fase progettuale poichè può raggiungere importanti valori. Nello scavo di Lion Yard, considerando la presenza delle fondazioni profonde ho evidenziato il fatto che il rigonfiamento crea una forza distribuita di taglio tra i pali di fondazione ed il terreno, anche tale sollecitazione dovrebbe essere considerata ai fini della progettazione. La problematica non si ferma solo sull’interazione terreno-fondazioni, infatti durante gli scavi di importanti fondazioni londinesi lo scarico tensionale ha creato uno spostamento significativo positivo verso la superfice di tratti di tunnel della metropolita, questo fenomeno può creare seri problemi di sicurezza nella rete dei trasporti pubblici. Infine sono stati messi a confronto i risultati del programma Flac con quelli di metodi semplificati, ho trovato che utilizzando il metodo iterativo di O’Brien i risultati sono simili alla realtà e il tempo di calcolo è molto inferiore di quello richiesto utilizzando Flac, 2-3 giorni. In conclusione posso affermare che grazie ad una dettagliata analisi parametrica è stato possibile stimare il rigonfiamento del terreno, argilla sovraconsolidata, nei due casi analizzati.

Pushover analysis of an existing reinforced concrete bridge:Jamboree Road Overcrossing in Irvine, California

The work for the present thesis started in California, during my semester as an exchange student overseas. California is known worldwide for its seismicity and its effort in the earthquake engineering research field. For this reason, I immediately found interesting the Structural Dynamics Professor, Maria Q. Feng's proposal, to work on a pushover analysis of the existing Jamboree Road Overcrossing bridge. Concrete is a popular building material in California, and for the most part, it serves its functions well. However, concrete is inherently brittle and performs poorly during earthquakes if not reinforced properly. The San Fernando Earthquake of 1971 dramatically demonstrated this characteristic. Shortly thereafter, code writers revised the design provisions for new concrete buildings so to provide adequate ductility to resist strong ground shaking. There remain, nonetheless, millions of square feet of non-ductile concrete buildings in California. The purpose of this work is to perform a Pushover Analysis and compare the results with those of a Nonlinear Time-History Analysis of an existing bridge, located in Southern California. The analyses have been executed through the software OpenSees, the Open System for Earthquake Engineering Simulation. The bridge Jamboree Road Overcrossing is classified as a Standard Ordinary Bridge. In fact, the JRO is a typical three-span continuous cast-in-place prestressed post-tension box-girder. The total length of the bridge is 366 ft., and the height of the two bents are respectively 26,41 ft. and 28,41 ft.. Both the Pushover Analysis and the Nonlinear Time-History Analysis require the use of a model that takes into account for the nonlinearities of the system. In fact, in order to execute nonlinear analyses of highway bridges it is essential to incorporate an accurate model of the material behavior. It has been observed that, after the occurrence of destructive earthquakes, one of the most damaged elements on highway bridges is a column. To evaluate the performance of bridge columns during seismic events an adequate model of the column must be incorporated. Part of the work of the present thesis is, in fact, dedicated to the modeling of bents. Different types of nonlinear element have been studied and modeled, with emphasis on the plasticity zone length determination and location. Furthermore, different models for concrete and steel materials have been considered, and the selection of the parameters that define the constitutive laws of the different materials have been accurate. The work is structured into four chapters, to follow a brief overview of the content. The first chapter introduces the concepts related to capacity design, as the actual philosophy of seismic design. Furthermore, nonlinear analyses both static, pushover, and dynamic, time-history, are presented. The final paragraph concludes with a short description on how to determine the seismic demand at a specific site, according to the latest design criteria in California. The second chapter deals with the formulation of force-based finite elements and the issues regarding the objectivity of the response in nonlinear field. Both concentrated and distributed plasticity elements are discussed into detail. The third chapter presents the existing structure, the software used OpenSees, and the modeling assumptions and issues. The creation of the nonlinear model represents a central part in this work. Nonlinear material constitutive laws, for concrete and reinforcing steel, are discussed into detail; as well as the different scenarios employed in the columns modeling. Finally, the results of the pushover analysis are presented in chapter four. Capacity curves are examined for the different model scenarios used, and failure modes of concrete and steel are discussed. Capacity curve is converted into capacity spectrum and intersected with the design spectrum. In the last paragraph, the results of nonlinear time-history analyses are compared to those of pushover analysis.

Operational Modal Analysis: the CEME Skywalk at UBC, Vancouver

Slender and lighter footbridges are becoming more and more popular to meet the transportation demand and the aesthetical requirements of the modern society. The widespread presence of such particular structures has become possible thanks to the availability of new, lightweight and still capable of carrying heavy loads material . Therefore, these kind of structure, are particularly sensitive to vibration serviceability problems, especially induced by human activities. As a consequence, it has been imperative to study the dynamic behaviour of such slender pedestrian bridges in order to define their modal characteristics. As an alternative to a Finite Element Analysis to find natural frequencies, damping and mode shape, a so-called Operational Modal Analysis is a valid tool to obtain these parameters through an ambient vibration test. This work provides a useful insight into the Operational Modal Analysis technique and It reports the investigation of the CEME Skywalk, a pedestrian bridge located at the University of British Columbia, in Vancouver, Canada. Furthermore, human-induced vibration tests have been performed and the dynamic characteristics derived with these tests have been compared with the ones from the ambient vibration tests. The effect of the dynamic properties of the two buildings supporting the CEME Skywalk on the dynamic behaviour of the bridge has been also investigated.

Experimental analysis of a separation control device based on plasma technology

In this thesis effects of plasma actuators based on Dielectric Barrier Discharge (DBD) technology over a NACA 0015 bidimensional airfoil have been analyzed in an experimental way, at low Reynolds number. Work developed on thesis has been carried on in partnership with the Department of Electrical Engineering of Università di Bologna, inside Wind Tunnel of the Applied Aerodynamic Laboratory of Aerospace Engineering faculty. In order to verify the effectiveness of these active control devices, the analysis has shown how actuators succeed in prevent boundary layer separation only in certain conditions af angle of attack and Reynolds numbers. Moreover, in this thesis actuators’ chordwise position effect has been also analyzed, together with the influence of steady and unsteady operations.

Separation control by means of oriented DBD plasma actuators: an experimental analysis in a wind tunnel

This thesis provides an experimental analysis of the effectiveness of oriented DBD plasma actuators over a NACA 0015 airfoil at low Reynolds numbers. Tests were performed in partnership with the Department of Electrical Engineering of Bologna University, in the wind tunnel of the Applied Aerodynamics Laboratory of Aerospace Engineering faculty. Lift coefficient measurements were carried out in order to verify how an oriented plasma jet succeeds in prevent boundary layer separation. Both actuators’ chord wise position and plasma jet orientation angle have been investigated to examine which configurations lead to the best results. A particular attention has been paid also to the analysis of results in steady and unsteady plasma actuation. Questa tesi offre un’analisi sperimentale sull’efficacia di attuatori al plasma orientabili, basati su una tecnologia DBD, installati su un profilo alare NACA 0015, a bassi numeri di Reynolds. Le prove sono state condotte in collaborazione con il Dipartimento di Ingegneria Elettrica dell’Università di Bologna, nella galleria del vento del Laboratorio di Aerodinamica Applicata della Facoltà di Ingegneria Aerospaziale di Forlì. Per verificare come un getto orientabile di plasma riesca a prevenire la separazione dello strato limite, sono state eseguite misure sul coefficiente di portanza. Sono state indagate sia la posizione degli attuatori lungo la corda che l’angolo con cui è orientato il getto di plasma, per vedere quali configurazioni conducono ai migliori risultati. Una particolare attenzione è stata riservata all’analisi dei risultati ottenuti con plasma continuo e pulsato.

Experimental analysis on the use of CCC systems to analyze the in-situ bearing capacity of C&D materials

Compaction is one of the most important processes in roadway construction. It is needed to achieve high quality and uniformity of pavement materials, which in turn better ensure long lasting performance.

Analysis of an innovative slim floor composite beam conformed by a custom GFRP pultruded profile and reinforced concrete.

GFRP pultruded profiles have shown to be structural profiles with great stiffness, strenght and very low specific weight, making it a great candidate for the rehabilitation of damaged strucutres. To further enhance the strucutral mechanism of these type of beams, the Slimflor composite structural system has lead as basis for this analysis; by replacing the steel beam with a GFRP pultruded profile. To further increase its composite action, a continuous shear connector has been set as part of the beam cross section as well as its needed reinforcement and fire protection.

Mechanical analysis and modeling of structural archetypes

This is a research B for the University of Bologna. The course is the civil engineering LAUREA MAGISTRALE at UNIBO. The main purpose of this research is to promote another way of explaining, analyzing and presenting some civil engineering aspects to the students worldwide by theory, modeling and photos. The basic idea is divided into three steps. The first one is to present and analyze the theoretical parts. So a detailed analysis of the theory combined with theorems, explanations, examples and exercises will cover this step. At the second, a model will make clear all these parts that were discussed in the theory by showing how the structures work or fail. The modeling is able to present the behavior of many elements, in scale which we use in the real structures. After these two steps an interesting exhibition of photos from the real world with comments will give the chance to the engineers to observe all these theoretical and modeling-laboratory staff in many different cases. For example many civil engineers in the world may know about the air pressure on the structures but many of them have never seen the extraordinary behavior of the bridge of Tacoma ‘dancing with the air’. At this point I would like to say that what I have done is not a book, but a research of how this ‘3 step’ presentation or explanation of some mechanical characteristics could be helpful. I know that my research is something different and new and in my opinion is very important because it helps students to go deeper in the science and also gives new ideas and inspirations. This way of teaching can be used at all lessons especially at the technical. Hope that one day all the books will adopt this kind of presentation.

Analysis of the introduction of a business process mapping system in Rosetti Marino spa

After a first theoric introduction about Business Process Re-engineering (BPR), are considered in particular the possible options found in literature regarding the following three macro-elements: the methodologies, the modelling notations and the tools employed for process mapping. The theoric section is the base for the analysis of the same elements into the specific case of Rosetti Marino S.p.A., an EPC contractor, operating in the Oil&Gas industry. Rosetti Marino implemented a tool developped internally in order to satisfy its needs in the most suitable way possible and buit a Map of all business processes,navigable on the Company Intranet. Moreover it adopted a methodology based upon participation, interfunctional communication and sharing. The GIGA introduction is analysed from a structural, human resources, political and symbolic point of view.

Laser shock peening treatment to control and moderate fatigue crack growth in aircraft structure based on residual stress engineering approach

Laser Shock Peening (LSP) is a surface enhancement treatment which induces a significant layer of beneficial compressive residual stresses of up to several mm underneath the surface of metal components in order to improve the detrimental effects of the crack growth behavior rate in it. The aim of this thesis is to predict the crack growth behavior in metallic specimens with one or more stripes which define the compressive residual stress area induced by the Laser Shock Peening treatment. The process was applied as crack retardation stripes perpendicular to the crack propagation direction with the object of slowing down the crack when approaching the peened stripes. The finite element method has been applied to simulate the redistribution of stresses in a cracked model when it is subjected to a tension load and to a compressive residual stress field, and to evaluate the Stress Intensity Factor (SIF) in this condition. Finally, the Afgrow software is used to predict the crack growth behavior of the component following the Laser Shock Peening treatment and to detect the improvement in the fatigue life comparing it to the baseline specimen. An educational internship at the “Research & Technologies Germany – Hamburg” department of AIRBUS helped to achieve knowledge and experience to write this thesis. The main tasks of the thesis are the following: •To up to date Literature Survey related to “Laser Shock Peening in Metallic Structures” •To validate the FE model developed against experimental measurements at coupon level •To develop design of crack growth slowdown in Centered Cracked Tension specimens based on residual stress engineering approach using laser peened strip transversal to the crack path •To evaluate the Stress Intensity Factor values for Centered Cracked Tension specimens after the Laser Shock Peening treatment via Finite Element Analysis •To predict the crack growth behavior in Centered Cracked Tension specimens using as input the SIF values evaluated with the FE simulations •To validate the results by means of experimental tests

Stability analysis of linear thin shells

Shell structure is widely used in engineering area. The purpose of this dissertation is to show the behavior of a thin shell under external load, especially for long cylindrical shell under compressive load, I analyzed not only for linear elastic problem and also for buckling problem, and by using finite element analysis it shows that the imperfection of a cylinder could affect the critical load which means the buckling capability of this cylinder. For linear elastic problem, I compared the theoretical results with the results got from Straus7 and Abaqus, and the results are really close. For the buckling problem I did the same: compared the theoretical and Abaqus results, the error is less than 1%, but in reality, it’s not possible to reach the theoretical buckling capability due to the imperfection of the cylinder, so I put different imperfection for the cylinder in Abaqus, and found out that with the increasing of the percentage of imperfection, the buckling capability decreases, for example 10% imperfection could decrease 40% of the buckling capability, and the outcome meet the buckling behavior in reality.