Design of a GNSS receiver for the ESEO mission

This thesis was carried out inside the ESA's ESEO mission and focus in the design of one of the secondary payloads carried on board the spacecraft: a GNSS receiver for orbit determination. The purpose of this project is to test the technology of the orbit determination in real time applications by using commercial components. The architecture of the receiver includes a custom part, the navigation computer, and a commercial part, the front-end, from Novatel, with COCOM limitation removed, and a GNSS antenna. This choice is motivated by the goal of demonstrating the correct operations in orbit, enabling a widespread use of this technology while lowering the cost and time of the device’s assembly. The commercial front-end performs GNSS signal acquisition, tracking and data demodulation and provides raw GNSS data to the custom computer. This computer processes this raw observables, that will be both transferred to the On-Board Computer and then transmitted to Earth and provided as input to the recursive estimation filter on-board, in order to obtain an accurate positioning of the spacecraft, using the dynamic model. The main purpose of this thesis, is the detailed design and development of the mentioned GNSS receiver up to the ESEO project Critical Design Review, including requirements definition, hardware design and breadboard preliminary test phase design.

Feedback linearization of antagonistically actuated variable stiffness joints with twisted string actuators

The work of this thesis is on the implementation of a variable stiffness joint antagonistically actuated by a couple of twisted-string actuator (TSA). This type of joint is possible to be applied in the field of robotics, like UB Hand IV (the anthropomorphic robotic hand developed by University of Bologna). The purposes of the activities are to build the joint dynamic model and simultaneously control the position and stiffness. Three different control approaches (Feedback linearization, PID, PID+Feedforward) are proposed and validated in simulation. To improve the properties of joint stiffness, a joint with elastic element is taken into account and discussed. To the end, the experimental setup that has been developed for the experimental validation of the proposed control approaches.

Analysis of aircraft load spectrum by means of flight simulator

Damage tolerance analysis is a quite new methodology based on prescribed inspections. The load spectra used to derive results of these analysis strongly influence the final defined inspections programs that for this reason must be as much as possible representative of load acting on the considered structural component and at the same time, obtained reducing both cost and time. The principal purpose of our work is in improving the actual condition developing a complete numerical Damage Tolerance analysis, able to prescribe inspection programs on typical aircraft critical components, respecting DT regulations, starting from much more specific load spectrum then those actually used today. In particular, these more specific load spectrum to design against fatigue have been obtained through an appositively derived flight simulator developed in a Matlab/Simulink environment. This dynamic model has been designed so that it can be used to simulate typical missions performing manually (joystick inputs) or completely automatic (reference trajectory need to be provided) flights. Once these flights have been simulated, model’s outputs are used to generate load spectrum that are then processed to get information (peaks, valleys) to perform statistical and/or comparison consideration with other load spectrum. However, also much more useful information (loads amplitude) have been extracted from these generated load spectrum to perform the previously mentioned predictions (Rainflow counting method is applied for this purpose). The entire developed methodology works in a complete automatic way, so that, once some specified input parameters have been introduced and different typical flights have been simulated both, manually or automatically, it is able to relate the effects of these simulated flights with the reduction of residual strength of the considered component.

Modeling and validation of the thermal behavior of buildings for the development of demand response methods

The representation of the thermal behaviour of the building is achieved through a relatively simple dynamic model that takes into account the effects due to the thermal mass of the building components. The model of a intra-floor apartment has been built in the Matlab-Simulink environment and considers the heat transmission through the external envelope, wall and windows, the internal thermal masses, (i.e. furniture, internal wall and floor slabs) and the sun gain due to opaque and see-through surfaces of the external envelope. The simulations results for the entire year have been compared and the model validated, with the one obtained with the dynamic building simulation software Energyplus.

Caratterizzazione e progettazione di un attuatore differenziale elastico compatto per la robotica collaborativa

Lo sviluppo della robotica collaborativa, in particolare nelle applicazioni di processi industriali in cui sono richieste la flessibilità decisionale di un utilizzatore umano e le prestazioni di forza e precisione garantite dal robot, pone continue sfide per il miglioramento della capacità di progettare e controllare al meglio questi apparati, rendendoli sempre più accessibili in termini economici e di fruibilità. Questo cambio di paradigma rispetto ai tradizionali robot industriali, verso la condivisone attiva degli ambienti di lavoro tra uomo e macchina, ha accelerato lo sviluppo di nuove soluzioni per rendere possibile l’impiego di robot che possano interagire con un ambiente in continua mutazione, in piena sicurezza. Una possibile soluzione, ancora non diffusa commercialmente, ma largamente presente in letteratura, è rappresentata dagli attuatori elastici. Tra gli attuatori elastici, l’architettura che ad oggi ha destato maggior interesse è quella seriale, in cui l’elemento cedevole viene posto tra l’uscita del riduttore ed il carico. La bibliografia mostra come alcuni limiti della architettura seriale possano essere superati a parità di proprietà dinamiche. La soluzione più promettente è l’architettura differenziale, che si caratterizza per l’utilizzo di riduttori ad un ingresso e due uscite. I vantaggi mostrati dai primi risultati scientifici evidenziano l’ottenimento di modelli dinamici ideali paragonabili alla più nota architettura seriale, superandola in compattezza ed in particolare semplificando l’installazione dei sensori necessari al controllo. In questa tesi viene effettuata un’analisi dinamica preliminare ed uno studio dell’attitudine del dispositivo ad essere utilizzato in contesto collaborativo. Una volta terminata questa fase, si presenta il design e la progettazione di un prototipo, con particolare enfasi sulla scelta di componenti commerciali ed il loro dimensionamento, oltre alla definizione della architettura costruttiva complessiva.

Feedback control of underactuated cable-driven parallel robots

In this work an Underactuated Cable-Driven Parallel Robot (UACDPR) that operates in the three dimensional Euclidean space is considered. The End-Effector has 6 degrees of freedom and is actuated by 4 cables, therefore from a mechanical point of view the robot is defined underconstrained. However, considering only three controlled pose variables, the degree of redundancy for the control theory can be considered one. The aim of this thesis is to design a feedback controller for a point-to-point motion that satisfies the transient requirements, and is capable of reducing oscillations that derive from the reduced number of constraints. A force control is chosen for the positioning of the End-Effector, and error with respect to the reference is computed through data measure of several sensors (load cells, encoders and inclinometers) such as cable lengths, tension and orientation of the platform. In order to express the relation between pose and cable tension, the inverse model is derived from the kinematic and dynamic model of the parallel robot. The intrinsic non-linear nature of UACDPRs systems introduces an additional level of complexity in the development of the controller, as a result the control law is composed by a partial feedback linearization, and damping injection to reduce orientation instability. The fourth cable allows to satisfy a further tension distribution constraint, ensuring positive tension during all the instants of motion. Then simulations with different initial conditions are presented in order to optimize control parameters, and lastly an experimental validation of the model is carried out, the results are analysed and limits of the presented approach are defined.