PM and material decay: analysis of dry depositions on horizontal and vertical surrogate surfaces through a Deposition Box system

Airborne Particulate Matter (PM), can get removed from the atmosphere through wet and dry mechanisms, and physically/chemically interact with materials and induce premature decay. The effect of dry depositions is a complex issue, especially for outdoor materials, because of the difficulties to collect atmospheric deposits repeatable in terms of mass and homogeneously distributed on the entire investigated substrate. In this work, to overcome these problems by eliminating the variability induced by outdoor removal mechanisms (e.g. winds and rainfalls), a new sampling system called ‘Deposition Box’, was used for PM sampling. Four surrogate materials (Cellulose Acetate, Regenerated Cellulose, Cellulose Nitrate and Aluminum) with different surfaces features were exposed in the urban-marine site of Rimini (Italy), in vertical and horizontal orientations. Homogeneous and reproducible PM deposits were obtained and different analytical techniques (IC, AAS, TOC, VP-SEM-EDX, Vis-Spectrophotometry) were employed to characterize their mass, dimension and composition. Results allowed to discriminate the mechanisms responsible of the dry deposition of atmospheric particles on surfaces with different nature and orientation and to determine which chemical species, and in which amount, tend to preferentially deposit on them. This work demonstrated that “Deposition Box” can represent an affordable tool to study dry deposition fluxes on materials and results obtained will be fundamental in order to extend this kind of exposure to actual building and heritage materials, to investigate the PM contribution in their decay.

Formulation of ionogel, hydrogel and films using a cellulose rich solid obtained from Pinus radiata

The purpose of my internship, carried out during my Erasmus period at the Complutense University of Madrid, was focused on the formulation of ionogels and hydrogels for the obtainment of films with high lignin content, and on their characterization measuring their antibacterial properties. For biomass formulation I used lignocellulosic biomass (Pinus Radiata) as raw material and ionic liquid as solvent. The two ionic liquids proposed were: 1-ethyl-3-methylimidazoliumdimethylphosphate [Emim][DMP] and 1-ethyl-3-methylimidazoliumdiethylphosphate [Emim][DEP]. The two-starting cellulose-rich solids were obtained from Pinus radiata wood that had been submitted to an organosolv process, to reduce its lignin content to fifteen (ORG15) and twenty per cent (ORG20). Having two ionic liquids and two solids available, the first phase of the project was devoted to the screening of both solids in both ionic liquids. Through this, it was possible to identify that only the [Emim][DMP] ionic liquid fulfils the purpose. It was also possible to discard the cellulose-rich solid ORG20 because its dissolution in the ionic liquid was not possible (after the time fixed) and, additionally, a Pinus radiata cellulose-rich solid bleached with hydrogen peroxide and containing ten per cent of lignin (ORG10B) was included in the screening. After screening, a total of five ionogels were subsequently formulated: two gels were formulated with the starting raw material ORG15 (with 1% and 1.75% cellulose, respectively) and three with ORG10B (with 1%, 1.75% and 3% cellulose, respectively). Five hydrogels were obtained from the ionogels. Rheological tests were performed on each ionogel and hydrogel. Finally, films were formulated from hydrogels and they were analysed by antibacterial testing to see if they could be applied as food packaging. In addition, antioxidant and properties such as opacity and transparency were also studied.

Deposizione elettrochimica di film polimerici foto-attivi per la realizzazione di celle solari

Plastic solar cells bear the potential for large-scale power generation based on flexible, lightweight, inexpensive materials. Since the discovery of the photo-induced electron transfer from a conjugated polymer (electron-donor) to fullerene or its derivatives molecules (electron-acceptors), followed by the introduction of the bulk heterojunction concept which means donors and acceptors blended together to realize the fotoactive layer, materials and deposition techniques have been extensively studied. In this work, electrochemical-deposition methods of polymeric conductive films were studied in order to realize bulk heterojunction solar cells. Indium Tin Oxide (ITO) glass electrodes modified with a thin layer of poly(3,4-ethylenedioxythiophene) (PEDOT) were electrochemically prepared under potentiodynamic and potentiostatic conditions; then those techniques were applied for the electrochemical co-deposition of donor and acceptor on modified ITO electrode to produce the active layer (blend). For the deposition of the electron-donor polymer the electropolymerization of many functionalized thiophene monomers was investigated while, as regards acceptors, fullerene was used first, then the study was focused on its derivative PCBM ([6,6]-phenyl-C61-butyric acid methyl ester). The polymeric films obtained (PEDOT and blend) were electrochemically and spectrophotometrically characterized and the film thicknesses were evaluated by atomic force microscopy (AFM). Finally, to check the performances and the efficiency of the realized solar cells, tests were carried out under standard conditions. Nowadays bulk heterojunction solar cells are still poorly efficient to be competitively commercialized. A challenge will be to find new materials and better deposition techniques in order to obtain better performances. The research has led to several breakthroughs in efficiency, with a power conversion efficiency approaching 5 %. The efficiency of the solar cells produced in this work is even lower (lower than 1 %). Despite all, solar cells of this type are interesting and may represent a cheaper and easier alternative to traditional silicon-based solar panels.

Deposizione elettrochimica di esacianoferrato di rame tramite un metodo "a due step"; caratterizzazione e valutazione delle prestazioni

In this thesis we have identified two electrochemical procedures for preparing two compounds of copper hexacyanoferrate (CuHCF) films with different compositions and structures. The deposition were carried out using a “two steps” method consisting in electrochemical oxidation of previously deposited metallic copper on carbon substrates (glassy carbon and graphite foil electrodes) in K3[Fe(CN)6] solution. Both films, CuHCF-methodA and CuHCF-methodB, were characterized by cyclic voltammetry (GC) and their study using XANES spectroscopy revealed evidence of different structures. Additionally, insertion and extraction of different cations (Na+, K+, Mg2+, Al3+ and Cs+) were performed and the results indicate that CuHCF-methodA has slightly better performances and operational stability than CuHCF-methodB. Data from galvanostatic charge-discharge tests confirme the latter observation. An application for amperometric detection of H2O2 and SEM micrographs are also reported for both films (method A and B). Comparing these results with a previous work of our research group, seems that the deposition of two different compounds using methodA and methodB is due to the different stoichiometry of ions Cu2+ e [Fe(CN)6]3– created near electrode surface during the dissolution step.