Experimental Study on Friction between Saline Ice and Steel

Understanding the interaction of sea ice with offshore structures is of primary importance for the development of technology in cold climate regions. The rheological properties of sea ice (strength, creep, viscosity) as well as the roughness of the contact surface are the main factors influencing the type of interaction with a structure. A device was developed and designed and small scale laboratory experiments were carried out to study sea ice frictional interaction with steel material by means of a uniaxial compression rig. Sea-ice was artificially grown between a stainless steel piston (of circular cross section) and a hollow cylinder of the same material, coaxial to the former and of the same surface roughness. Three different values for the roughness were tested: 1.2, 10 and 30 μm Ry (maximum asperities height), chosen as representative values for typical surface conditions, from smooth to normally corroded steel. Creep tests (0.2, 0.3, 0.4 and 0.6 kN) were conducted at T = -10 ºC. By pushing the piston head towards the cylinder base, three different types of relative movement were observed: 1) the piston slid through the ice, 2) the piston slid through the ice and the ice slid on the surface of the outer cylinder, 3) the ice slid only on the cylinder surface. A cyclic stick-slip motion of the piston was detected with a representative frequency of 0.1 Hz. The ratio of the mean rate of axial displacement to the frequency of the stick-slip oscillations was found to be comparable to the roughness length (Sm). The roughness is the most influential parameter affecting the amplitude of the oscillations, while the load has a relevant influence on the their frequency. Guidelines for further investigations were recommended. Marco Nanetti - seloselo@virgilio.it

Statistical Mechanics of Monomer-Dimer Models on Complete and Erdös-Rényi Graphs

Nella tesi sono trattate due famiglie di modelli meccanico statistici su vari grafi: i modelli di spin ferromagnetici (o di Ising) e i modelli di monomero-dimero. Il primo capitolo è dedicato principalmente allo studio del lavoro di Dembo e Montanari, in cui viene risolto il modello di Ising su grafi aleatori. Nel secondo capitolo vengono studiati i modelli di monomero-dimero, a partire dal lavoro di Heilemann e Lieb,con l'intento di dare contributi nuovi alla teoria. I principali temi trattati sono disuguaglianze di correlazione, soluzioni esatte su alcuni grafi ad albero e sul grafo completo, la concentrazione dell'energia libera intorno al proprio valor medio sul grafo aleatorio diluito di Erdös-Rényi.

Numerical simulation of interdigitated back contact hetero-junction solar cells

The goal of this thesis is the application of an opto-electronic numerical simulation to heterojunction silicon solar cells featuring an all back contact architecture (Interdigitated Back Contact Hetero-Junction IBC-HJ). The studied structure exhibits both metal contacts, emitter and base, at the back surface of the cell with the objective to reduce the optical losses due to the shadowing by front contact of conventional photovoltaic devices. Overall, IBC-HJ are promising low-cost alternatives to monocrystalline wafer-based solar cells featuring front and back contact schemes, in fact, for IBC-HJ the high concentration doping diffusions are replaced by low-temperature deposition processes of thin amorphous silicon layers. Furthermore, another advantage of IBC solar cells with reference to conventional architectures is the possibility to enable a low-cost assembling of photovoltaic modules, being all contacts on the same side. A preliminary extensive literature survey has been helpful to highlight the specific critical aspects of IBC-HJ solar cells as well as the state-of-the-art of their modeling, processing and performance of practical devices. In order to perform the analysis of IBC-HJ devices, a two-dimensional (2-D) numerical simulation flow has been set up. A commercial device simulator based on finite-difference method to solve numerically the whole set of equations governing the electrical transport in semiconductor materials (Sentuarus Device by Synopsys) has been adopted. The first activity carried out during this work has been the definition of a 2-D geometry corresponding to the simulation domain and the specification of the electrical and optical properties of materials. In order to calculate the main figures of merit of the investigated solar cells, the spatially resolved photon absorption rate map has been calculated by means of an optical simulator. Optical simulations have been performed by using two different methods depending upon the geometrical features of the front interface of the solar cell: the transfer matrix method (TMM) and the raytracing (RT). The first method allows to model light prop-agation by plane waves within one-dimensional spatial domains under the assumption of devices exhibiting stacks of parallel layers with planar interfaces. In addition, TMM is suitable for the simulation of thin multi-layer anti reflection coating layers for the reduction of the amount of reflected light at the front interface. Raytracing is required for three-dimensional optical simulations of upright pyramidal textured surfaces which are widely adopted to significantly reduce the reflection at the front surface. The optical generation profiles are interpolated onto the electrical grid adopted by the device simulator which solves the carriers transport equations coupled with Poisson and continuity equations in a self-consistent way. The main figures of merit are calculated by means of a postprocessing of the output data from device simulation. After the validation of the simulation methodology by means of comparison of the simulation result with literature data, the ultimate efficiency of the IBC-HJ architecture has been calculated. By accounting for all optical losses, IBC-HJ solar cells result in a theoretical maximum efficiency above 23.5% (without texturing at front interface) higher than that of both standard homojunction crystalline silicon (Homogeneous Emitter HE) and front contact heterojuction (Heterojunction with Intrinsic Thin layer HIT) solar cells. However it is clear that the criticalities of this structure are mainly due to the defects density and to the poor carriers transport mobility in the amorphous silicon layers. Lastly, the influence of the most critical geometrical and physical parameters on the main figures of merit have been investigated by applying the numerical simulation tool set-up during the first part of the present thesis. Simulations have highlighted that carrier mobility and defects level in amorphous silicon may lead to a potentially significant reduction of the conversion efficiency.

La misura dell'impedenza locale con tecnologia Contact nello studio elettrofisiologico

Questo lavoro di Tesi Magistrale, si focalizza sulla più importante delle aritmie atriali, ovvero la Fibrillazione Atriale, e sul trattamento della stessa attraverso le procedure di ablazione a radio frequenza (RF). Il lavoro di tesi, svolto presso l'Ospedale 'M. Bufalini' di Cesena, affronta in particolare l'uso della tecnologia EnSite NavX (un sistema di mappaggio elettroanatomico delle cavità cardiache) ed EnSite Contact (un sistema basato sulla misura dell'impedenza locale per la valutazione del contatto elettrodo tessuto). L'acquisizione e l'analisi dei dati di ECI (indice di accoppiamento elettrico), forniti dal modulo Contact, hanno permesso di comprendere come questo parametro, derivato dalla misura dell'impedenza locale, possa contribuire a fornire importanti informazioni in real-time all'elettrofisiologo e come lo studio della sua dinamica, con particolare attenzione alle variazioni tra pre e post ablazione, possa risultare utile per verificare l'avvenuta erogazione di energia ai tessuti.

Analisi di celle solari "back contact" mediante simulatore di reti elettriche distribuite basato su spice

Analisi di celle solari mediante simulatore di reti elettriche distribuite basato su Spice

Creativite langagiere et contact de langues: Le cas du langage sms et chat chez les jeunes camerounais

Résumé L’apparition de l’internet au Cameroun offre une réelle occasion d’échange, surtout pour les jeunes. Les innovations de la toile sont à considérer à plusieurs niveaux, les linguistes sous tous les cieux ont actuellement à débattre du langage SMS et CHAT, qui est, d’après (Dejond ,2002) « un mélange d’anglicisme, d’abréviation, de sigles et de rebus d’écriture phonétique. On écrit comme on parle. » Cette forme d’écriture facile à transcrire est éloignée des normes orthographiques et grammaticales du français standard. En effet, le langage SMS et CHAT des jeunes camerounais n’obéit qu’à la norme dictée par l’imagination de ses adeptes. Il se caractérise par des phénomènes comme la troncation, l’élision vocalique et consonantique ou l’agglutination à l’intérieur des mots. L’un des phénomènes les plus marquants est l’introduction des chiffres allant de 1 à 9 dans la graphie de certains mots. Ces écritures simplifiées nécessitent souvent l’intuition ou la compétence linguistique des lecteurs pour décrypter le message, le but étant l’interprétation du contenu. De plus, le type de message est strictement communicatif ou expressif et non normatif. Ainsi, l’essentiel est de faire passer un message. Les règles, les principes ou les contraintes qui gouvernent la transcription orthographique d’un mot français sont relégués au second plan. L’écriture texto employé par les jeunes camerounais cherche parcimonieusement à en dire le plus avec un minimum de caractère. Pour cela, on chatte entre amis, parents ou avec des connaissances éparpillée de part le monde qui naissent de ces rencontres virtuelles.

Limiting theorems in statistical mechanics. The mean-field case.

The Curie-Weiss model is defined by ah Hamiltonian according to spins interact. For some particular values of the parameters, the sum of the spins normalized with square-root normalization converges or not toward Gaussian distribution. In the thesis we investigate some correlations between the behaviour of the sum and the central limit for interacting random variables.

Statistical mechanics of polymer models: rigorous results and applications

Monomer-dimer models are amongst the models in statistical mechanics which found application in many areas of science, ranging from biology to social sciences. This model describes a many-body system in which monoatomic and diatomic particles subject to hard-core interactions get deposited on a graph. In our work we provide an extension of this model to higher-order particles. The aim of our work is threefold: first we study the thermodynamic properties of the newly introduced model. We solve analytically some regular cases and find that, differently from the original, our extension admits phase transitions. Then we tackle the inverse problem, both from an analytical and numerical perspective. Finally we propose an application to aggregation phenomena in virtual messaging services.