Development of an innovative non rule-based energy management strategy for a Hybrid Electric Vehicle, structured for predictive driving controls based on external information knowledge

Recently, the interest of the automotive market for hybrid vehicles has increased due to the more restrictive pollutants emissions legislation and to the necessity of decreasing the fossil fuel consumption, since such solution allows a consistent improvement of the vehicle global efficiency. The term hybridization regards the energy flow in the powertrain of a vehicle: a standard vehicle has, usually, only one energy source and one energy tank; instead, a hybrid vehicle has at least two energy sources. In most cases, the prime mover is an internal combustion engine (ICE) while the auxiliary energy source can be mechanical, electrical, pneumatic or hydraulic. It is expected from the control unit of a hybrid vehicle the use of the ICE in high efficiency working zones and to shut it down when it is more convenient, while using the EMG at partial loads and as a fast torque response during transients. However, the battery state of charge may represent a limitation for such a strategy. That’s the reason why, in most cases, energy management strategies are based on the State Of Charge, or SOC, control. Several studies have been conducted on this topic and many different approaches have been illustrated. The purpose of this dissertation is to develop an online (usable on-board) control strategy in which the operating modes are defined using an instantaneous optimization method that minimizes the equivalent fuel consumption of a hybrid electric vehicle. The equivalent fuel consumption is calculated by taking into account the total energy used by the hybrid powertrain during the propulsion phases. The first section presents the hybrid vehicles characteristics. The second chapter describes the global model, with a particular focus on the energy management strategies usable for the supervisory control of such a powertrain. The third chapter shows the performance of the implemented controller on a NEDC cycle compared with the one obtained with the original control strategy.

Development of a thermochemical/biological process to convert waste biomass into new resources

The increasing attention to environmental issues of recent times encourages us to find new methods for the production of energy from renewable sources, and to improve existing ones, increasing their energy yield. Most of the waste and agricultural residues, with a high content of lignin and non-hydrolysable polymers, cannot be effectively transformed into biofuels with existing technology. The purpose of the study was to develop a new thermochemical/ biological process (named Py-AD) for the valorization of scarcely biodegradable substances. A complete continuous prototype was design built and run for 1 year. This consists into a slow pyrolysis system coupled with two sequential digesters and showed to produce a clean pyrobiogas (a biogas with significant amount of C2-C3 hydrocarbons and residual CO/H2), biochar and bio-oil. Py-AD yielded 31.7% w/w biochar 32.5% w/w oil and 24.8% w/w pyrobiogas. The oil condensate obtained was fractionated in its aqueous and organic fraction (87% and 13% respectively). Subsequently, the anaerobic digestion of aqueous fraction was tested in a UASB reactor, for 180 days, in increasing organic loading rate (OLR). The maximum convertible concentration without undergoing instability phenomena and with complete degradation of pyrogenic chemicals was 1.25 gCOD L digester-1 d-1. The final yield of biomethane was equal to 40% of the theoretical yield and with a noticeable additional production equal to 20% of volatile fatty acids. The final results confirm that anaerobic digestion can be used as a useful tool for cleaning of slow pyrolysis products (both gas and condensable fraction) and the obtaining of relatively clean pyrobiogas that could be directly used in internal combustion engine.

Development of a Predictive Control Function for a Plug-in Hybrid Electric Vehicle with Electrically-heated Catalyst

This master thesis work is focused on the development of a predictive EHC control function for a diesel plug-in hybrid electric vehicle equipped with a EURO 7 compliant exhaust aftertreatment system (EATS), with the purpose of showing the advantages provided by the implementation of a predictive control strategy with respect to a rule-based one. A preliminary step will be the definition of an accurate powertrain and EATS physical model, starting from already existing and validated applications. Then, a rule-based control strategy managing the torque split between the electric motor (EM) and the internal combustion engine (ICE) will be developed and calibrated, with the main target of limiting tailpipe NOx emission by taking into account EM and ICE operating conditions together with EATS conversion efficiency. The information available from vehicle connectivity will be used to reconstruct the future driving scenario, also referred to as electronic horizon (eHorizon), and in particular to predict ICE first start. Based on this knowledge, an EATS pre-heating phase can be planned to avoid low pollutant conversion efficiencies, thus preventing high NOx emission due to engine cold start. Consequently, the final NOx emission over the complete driving cycle will be strongly reduced, allowing to comply with the limits potentially set by the incoming EURO 7 regulation. Moreover, given the same NOx emission target, the gain achieved thanks to the implementation of an EHC predictive control function will allow to consider a simplified EATS layout, thus reducing the related manufacturing cost. The promising results achieved in terms of NOx emission reduction show the effectiveness of the application of a predictive control strategy focused on EATS thermal management and highlight the potential of a complete integration and parallel development of involved vehicle physical systems, control software and connectivity data management.