Advanced N.D.T.: analisi e studio di componenti in materiale composito

Numerose evidenze dimostrano che le proprietà dei materiali compositi sono strettamente legate ai processi produttivi, alle tipologie di fibra e resina impiegate nel materiale stesso. Proprietà caratterizzate anche dai difetti contenuti nel materiale stesso. Nella tesi si presta particolare attenzione al processo produttivo con prepreg e autoclave trattando anche il tema della stesura di un ply-book. Si valutano in modo teorico e critico alcuni tra i metodi N.D.T. più avanzati tra cui: P.T.(Penetrant Test), Rx(Radiography Test), UT (Ultrasound Test in Phased Array) e IRT (InfraRed Termography - Pulsata). Molteplici sono i componenti testati che variano tra loro per: tipologia di resina e fibra impiegata, processo produttivo e geometria. Tutti questi componenti permettono di capire come i singoli parametri influenzino la visualizzazione e l'applicabilità delle tecniche N.D.T. sopra citate. Su alcuni provini è stata eseguita la prova meccanica Drop Weight Test secondo ASTM D7136 per correlare le aree di delaminazione indotte e la sensibilità di ogni singolo metodo, visualizzando così la criticità indotta dagli urti con bassa energia di impatto (BVID Barely Invisible Impact)di cui i materiali compositi soffrono durante la "service life". A conclusione del lavoro si potrà comprendere come solo l'analisi con più metodi in parallelo permetta di ottenere una adeguata Probability Of Detection.

Influence of advanced load simulation models on fatigue design of jackets for offshore wind turbines.

Constant developments in the field of offshore wind energy have increased the range of water depths at which wind farms are planned to be installed. Therefore, in addition to monopile support structures suitable in shallow waters (up to 30 m), different types of support structures, able to withstand severe sea conditions at the greater water depths, have been developed. For water depths above 30 m, the jacket is one of the preferred support types. Jacket represents a lightweight support structure, which, in combination with complex nature of environmental loads, is prone to highly dynamic behavior. As a consequence, high stresses with great variability in time can be observed in all structural members. The highest concentration of stresses occurs in joints due to their nature (structural discontinuities) and due to the existence of notches along the welds present in the joints. This makes them the weakest elements of the jacket in terms of fatigue. In the numerical modeling of jackets for offshore wind turbines, a reduction of local stresses at the chord-brace joints, and consequently an optimization of the model, can be achieved by implementing joint flexibility in the chord-brace joints. Therefore, in this work, the influence of joint flexibility on the fatigue damage in chord-brace joints of a numerical jacket model, subjected to advanced load simulations, is studied.

Recycling of end of life concrete fines (0 - 4 mm) into silica and cement

The purpose of this work is to find a methodology in order to make possible the recycling of fines (0 - 4 mm) in the Construction and Demolition Waste (CDW) process. At the moment this fraction is a not desired by-product: it has high contaminant content, it has to be separated from the coarse fraction, because of its high water absorption which can affect the properties of the concrete. In fact, in some countries the use of fines recycled aggregates is highly restricted or even banned. This work is placed inside the European project C2CA (from Concrete to Cement and Clean Aggregates) and it has been held in the Faculty of Civil Engineering and Geosciences of the Technical University of Delft, in particular, in the laboratory of Resources And Recycling. This research proposes some procedures in order to close the loop of the entire recycling process. After the classification done by ADR (Advanced Dry Recovery) the two fractions "airknife" and "rotor" (that together constitute the fraction 0 - 4 mm) are inserted in a new machine that works at high temperatures. The temperatures analysed in this research are 600 °C and 750 °C, cause at that temperature it is supposed that the cement bounds become very weak. The final goal is "to clean" the coarse fraction (0,250 - 4 mm) from the cement still attached to the sand and try to concentrate the cement paste in the fraction 0 - 0,250 mm. This new set-up is able to dry the material in very few seconds, divide it into two fractions (the coarse one and the fine one) thanks to the air and increase the amount of fines (0 - 0,250 mm) promoting the attrition between the particles through a vibration device. The coarse fraction is then processed in a ball mill in order to improve the result and reach the final goal. Thanks to the high temperature it is possible to markedly reduce the milling time. The sand 0 - 2 mm, after being heated and milled is used to replace 100% of norm sand in mortar production. The results are very promising: the mortar made with recycled sand reaches an early strength, in fact the increment with respect to the mortar made with norm sand is 20% after three days and 7% after seven days. With this research it has been demonstrated that once the temperature is increased it is possible to obtain a clean coarse fraction (0,250 - 4 mm), free from cement paste that is concentrated in the fine fraction 0 - 0,250 mm. The milling time and the drying time can be largely reduced. The recycled sand shows better performance in terms of mechanical properties with respect to the natural one.