Substructuring approache in state space models for dynamic system parameters identification

In the recent decade, the request for structural health monitoring expertise increased exponentially in the United States. The aging issues that most of the transportation structures are experiencing can put in serious jeopardy the economic system of a region as well as of a country. At the same time, the monitoring of structures is a central topic of discussion in Europe, where the preservation of historical buildings has been addressed over the last four centuries. More recently, various concerns arose about security performance of civil structures after tragic events such the 9/11 or the 2011 Japan earthquake: engineers looks for a design able to resist exceptional loadings due to earthquakes, hurricanes and terrorist attacks. After events of such a kind, the assessment of the remaining life of the structure is at least as important as the initial performance design. Consequently, it appears very clear that the introduction of reliable and accessible damage assessment techniques is crucial for the localization of issues and for a correct and immediate rehabilitation. The System Identification is a branch of the more general Control Theory. In Civil Engineering, this field addresses the techniques needed to find mechanical characteristics as the stiffness or the mass starting from the signals captured by sensors. The objective of the Dynamic Structural Identification (DSI) is to define, starting from experimental measurements, the modal fundamental parameters of a generic structure in order to characterize, via a mathematical model, the dynamic behavior. The knowledge of these parameters is helpful in the Model Updating procedure, that permits to define corrected theoretical models through experimental validation. The main aim of this technique is to minimize the differences between the theoretical model results and in situ measurements of dynamic data. Therefore, the new model becomes a very effective control practice when it comes to rehabilitation of structures or damage assessment. The instrumentation of a whole structure is an unfeasible procedure sometimes because of the high cost involved or, sometimes, because it’s not possible to physically reach each point of the structure. Therefore, numerous scholars have been trying to address this problem. In general two are the main involved methods. Since the limited number of sensors, in a first case, it’s possible to gather time histories only for some locations, then to move the instruments to another location and replay the procedure. Otherwise, if the number of sensors is enough and the structure does not present a complicate geometry, it’s usually sufficient to detect only the principal first modes. This two problems are well presented in the works of Balsamo [1] for the application to a simple system and Jun [2] for the analysis of system with a limited number of sensors. Once the system identification has been carried, it is possible to access the actual system characteristics. A frequent practice is to create an updated FEM model and assess whether the structure fulfills or not the requested functions. Once again the objective of this work is to present a general methodology to analyze big structure using a limited number of instrumentation and at the same time, obtaining the most information about an identified structure without recalling methodologies of difficult interpretation. A general framework of the state space identification procedure via OKID/ERA algorithm is developed and implemented in Matlab. Then, some simple examples are proposed to highlight the principal characteristics and advantage of this methodology. A new algebraic manipulation for a prolific use of substructuring results is developed and implemented.

Pushover analysis of an existing reinforced concrete bridge:Jamboree Road Overcrossing in Irvine, California

The work for the present thesis started in California, during my semester as an exchange student overseas. California is known worldwide for its seismicity and its effort in the earthquake engineering research field. For this reason, I immediately found interesting the Structural Dynamics Professor, Maria Q. Feng's proposal, to work on a pushover analysis of the existing Jamboree Road Overcrossing bridge. Concrete is a popular building material in California, and for the most part, it serves its functions well. However, concrete is inherently brittle and performs poorly during earthquakes if not reinforced properly. The San Fernando Earthquake of 1971 dramatically demonstrated this characteristic. Shortly thereafter, code writers revised the design provisions for new concrete buildings so to provide adequate ductility to resist strong ground shaking. There remain, nonetheless, millions of square feet of non-ductile concrete buildings in California. The purpose of this work is to perform a Pushover Analysis and compare the results with those of a Nonlinear Time-History Analysis of an existing bridge, located in Southern California. The analyses have been executed through the software OpenSees, the Open System for Earthquake Engineering Simulation. The bridge Jamboree Road Overcrossing is classified as a Standard Ordinary Bridge. In fact, the JRO is a typical three-span continuous cast-in-place prestressed post-tension box-girder. The total length of the bridge is 366 ft., and the height of the two bents are respectively 26,41 ft. and 28,41 ft.. Both the Pushover Analysis and the Nonlinear Time-History Analysis require the use of a model that takes into account for the nonlinearities of the system. In fact, in order to execute nonlinear analyses of highway bridges it is essential to incorporate an accurate model of the material behavior. It has been observed that, after the occurrence of destructive earthquakes, one of the most damaged elements on highway bridges is a column. To evaluate the performance of bridge columns during seismic events an adequate model of the column must be incorporated. Part of the work of the present thesis is, in fact, dedicated to the modeling of bents. Different types of nonlinear element have been studied and modeled, with emphasis on the plasticity zone length determination and location. Furthermore, different models for concrete and steel materials have been considered, and the selection of the parameters that define the constitutive laws of the different materials have been accurate. The work is structured into four chapters, to follow a brief overview of the content. The first chapter introduces the concepts related to capacity design, as the actual philosophy of seismic design. Furthermore, nonlinear analyses both static, pushover, and dynamic, time-history, are presented. The final paragraph concludes with a short description on how to determine the seismic demand at a specific site, according to the latest design criteria in California. The second chapter deals with the formulation of force-based finite elements and the issues regarding the objectivity of the response in nonlinear field. Both concentrated and distributed plasticity elements are discussed into detail. The third chapter presents the existing structure, the software used OpenSees, and the modeling assumptions and issues. The creation of the nonlinear model represents a central part in this work. Nonlinear material constitutive laws, for concrete and reinforcing steel, are discussed into detail; as well as the different scenarios employed in the columns modeling. Finally, the results of the pushover analysis are presented in chapter four. Capacity curves are examined for the different model scenarios used, and failure modes of concrete and steel are discussed. Capacity curve is converted into capacity spectrum and intersected with the design spectrum. In the last paragraph, the results of nonlinear time-history analyses are compared to those of pushover analysis.

Seismic performance of rooftop cooling towers in buildings

Negli ultimi anni la ricerca ha fatto grandi passi avanti riguardo ai metodi di progetto e realizzazione delle strutture portanti degli edifici, a tal punto da renderle fortemente sicure sotto tutti i punti di vista. La nuova frontiera della ricerca sta quindi virando su aspetti che non erano mai stati in primo piano finora: gli elementi non-strutturali. Considerati fino ad oggi semplicemente carico accessorio, ci si rende sempre più conto della loro capacità di influire sui comportamenti delle strutture e sulla sicurezza di chi le occupa. Da qui nasce l’esigenza di questo grande progetto chiamato BNCs (Building Non-structural Component System), ideato dall’Università della California - San Diego e sponsorizzato dalle maggiori industrie impegnate nel campo delle costruzioni. Questo progetto, a cui ho preso parte, ha effettuato test su tavola vibrante di un edificio di cinque piani in scala reale, completamente arredato ed allestito dei più svariati elementi non-strutturali. Lo scopo della tesi in questione, ovviamente, riguarda l’identificazione strutturale e la verifica della sicurezza di uno di questi elementi non-strutturali: precisamente la torre di raffreddamento posta sul tetto dell’edificio (del peso di circa 3 tonnellate). Partendo da una verifica delle regole e calcoli di progetto, si è passato ad una fase di test sismici ed ispezioni post-test della torre stessa, infine tramite l’analisi dei dati raccolti durante i test e si è arrivati alla stesura di conclusioni.

Seismic vulnerability of the ancient albergotti's manor in Arezzo, Italy

The thesis moves from the need of understanding how a historical building would behave in case of earthquake and this purpose is strongly linked to the fact that the majority of Italian structures are old ones placed in seismic sites. Primarily an architectural and chronological research is provided in order to figure out how the building has developed in time; then, after the reconstruction of the skeleton of the analyzed element (“Villa i Bossi” in Gragnone, AR), a virtual model is created such that the main walls and sections are tested according to the magnitude of expected seismic events within the reference area. This approach is basically aimed at verifying the structure’s reliability as composed by single units; the latter are treated individually in order to find out all the main critical points where rehabilitation might be needed. Finally the most harmful sections are studied in detail and proper strengthening is advised according to the current know-how.

Comportamento ciclico di un pilastro in C.C.A inghisato in fondazione: comportamento sperimentale e modellazione numerica

Vista la necessità di migliorare le prestazioni sismiche delle costruzioni, in particolare di quelle prefabbricate, in questa tesi è stato studiato il comportamento di un particolare tipo di collegamento fra pilastro prefabbricato e plinto di fondazione, proposto e utilizzato dalla ditta APE di Montecchio Emilia. Come noto, l'assemblaggio degli elementi prefabbricati pone il problema delle modalità di collegamento nei nodi, le quali condizionano il comportamento statico e la risposta al sisma dell'insieme strutturale. Per studiare il comportamento del collegamento in questione, sono state effettuate delle prove di pressoflessione ciclica su due provini. Inoltre, sono stati sviluppati dei modelli numerici con l'obiettivo di simulare il comportamento reale. Si è utilizzato il software Opensees (the Open System for Earthquake Engineering Simulation), creato per la simulazione sismica delle strutture.

Neotettonica della faglia Nord-Anatolica nel Mare di Marmara. Analisi di dati sismici a riflessione e morfobatimetrici ad alta risoluzione

Il 17 agosto 1999 un violento terremoto di Mw 7,4 (terremoto di Izmit) ha interessato l’area del Golfo di Izmit, dove il segmento settentrionale della Faglia Nord-Anatolica (FNA) entra nel Mare di Marmara. Oltre a causare enormi danni e un numero di vittime altissimo (oltre 20000), la dislocazione orizzontale di oltre 5 metri in prossimità dell’epicentro ha caricato tettonicamente il segmento della FNA verso Istanbul. Da qui, l’importanza di un modello geologico-strutturale condiviso dalla comunità scientifica per questo ramo della Faglia Nord Anatolica, per la formulazione dei modelli di stima del rischio sismico in una zona della Turchia molto densamente popolata (oltre 12 milioni di persone). I numerosi studi di geologia e geofisica marina condotti nel Golfo di Izmit e più in generale nel Mare di Marmara, hanno avuto un grosso impulso in concomitanza del terremoto del 1999 e negli anni successivi, quando il Mare di Marmara è stato inserito tra i siti di importanza strategica. Nonostante la grande mole di dati raccolti e le pubblicazioni di lavori importanti che hanno contribuito a portare nuova luce sulla geologia di questo territorio complesso, permangono ancora incertezze e controversie sui rapporti le tra la formazione del bacino di Marmara e la FNA. Questo lavoro di tesi ha lo scopo di esaminare la cinematica della FNA nell’area del Mare di Marmara, in generale, ed in particolare lungo i vari bacini allineati lungo il ramo settentrionale: da Est verso Ovest, il Bacino di Cinarcik, il Bacino di Kumburgaz, il Bacino Centrale ed il Bacino di Tekirdag. Analizzeremo la natura e il grado di attività dei segmenti individuati da zone di trasferimento (bending o overstep) e tenteremo di cartografare la geometria, lo stile strutturale e la lunghezza di ciascun segmento, per effettuare una stima del potenziale sismogenetico di ciascun ramo utilizzando relazioni empiriche.

Una scossa all'economia: le conseguenze del sisma dell'Aquilano. Traduzione dall'inglese in italiano di un articolo di ricerca economica ed esperienza di collaborazione con gli autori.

The aim of this dissertation is to provide a translation from English into Italian of a specialised scientific article published in the Cambridge Working Papers in Economics series. In this text, the authors estimate the economic consequences of the earthquake that hit the Abruzzo region in 2009. An extract of this translation will be published as part of conference proceedings. The main reason behind this choice is a personal interest in specialised translation in the economic domain. Moreover, the subject of the article is of particular interest to the Italian readership. The aim of this study is to show how a non-specialised translator can tackle with such a highly specialised translation with the use of appropriate terminology resources and the collaboration of field experts. The translation could be of help to other Italian linguists looking for translated material in this particular domain where English seems to be the dominant language. In order to ensure consistent terminology and adequate style, the document has been translated with the use of different resources, such as dictionaries, glossaries and specialised corpora. I also contacted field experts and the authors of text. The collaboration with the authors proved to be an invaluable resource yet one to be carefully managed. This work is divided into 5 chapters. The first deals with domain-specific sublanguages. The second gives an overview of corpus linguistics and describes the corpora designed for the translation. The third provides an analysis of the article, focusing on syntactical, lexical and structural features while the fourth presents the translation, side-by-side with the source text. The fifth comments on the main difficulties encountered in the translation and the strategies used, as well as the relationship with the authors and their review of the published text. Appendix I contains the econometric glossary English – Italian.

Seismic Retrofitting of a Historic Structure with Limited Construction Documentation

Many buildings constructed during the middle of the 20th century were constructed with criteria that fall short of current requirements. Although shortcomings are possible in all aspects of the design, the inadequacies in terms of seismic design present a more pressing issue to human life. This risk has been seen in various earthquakes that have struck Italy recently, and subsequently, the codes have been altered to account for this underestimated danger. Structures built after these changes remain at risk and must be retrofitted depending on their use. This report centers around the Giovanni Michelucci Institute of Mathematics at the University of Bologna and the work required to modify the building so that it can withstand 60% of the current design requirements. The goal of this particular report is to verify the previous reports written in Italian and present an accurate analysis along with intervention suggestions for this particular building. The work began with an investigation into the previous sources and work to find out how the structure had been interpreted. After understanding the building, corrections were made where required, and the failing elements were organized graphically to more easily show where the building needed the most work. Once the critical zones were mapped, remediation techniques were tested on the top floor, and the modeling techniques and effects of the interventions were presented to assist in further work on the structure.