Processi integrati per l’intensificazione di processo: reazione di fotocatalisi accoppiata alla pervaporazione, la dialisi e all’ozonizzazione

L’accoppiamento di diverse operazioni unitarie può in certi casi portare ad una cosiddetta “intensificazione di processo”, cioè ad un aumento sostanziale delle rese, dell’efficienza e della sostenibilità. Nel presente lavoro sono state pertanto analizzate le potenzialità di accoppiamento della fotocatalisi, il più studiato tra i “processi di ossidazione avanzata”, sia con alcuni processi a membrana per la sintesi verde di aromi sia con l’ozonizzazione per la depurazione di acque. È stato dimostrato che in entrambi i casi l’ottenimento di una significativa intensificazione di processo dipende in gran parte dai parametri operativi, in particolare dal rapporto, delta, tra la velocità caratteristica di fotocatalisi e quella del processo accoppiato. Nel caso della sintesi di aromi, in cui la fotocatalisi viene accoppiata con la pervaporazione o con la dialisi ricircolando al reattore il retentato dalla cella con la membrana. Il parametro delta dipende dalla velocità di reazione, dalle proprietà di trasporto delle membrane e naturalmente dal volume del rettore e dall’area della membrana. La reazione fotocatalitica produce l’aroma, ad esempio vanillina da acido ferulico, per ossidazione parziale e grazie al recupero del prodotto se ne evita l’ulteriore ossidazione aumentandone pertanto la resa. L’operare in apparati separati offre diversi vantaggi come la possibilità di variare senza vincoli il rapporto tra area della membrana e volume del reattore, ma impone di considerare anche il grado effettivo di accoppiamento dei processi. In questo caso, come evidenziato dal modello matematico, un sufficientemente elevato rapporto di ricircolo consente comunque di integrare efficacemente i processi. Nell’ozonizzazione fotocatalitica si hanno due importanti vantaggi: l’aumento della velocità di degradazione grazie alla sinergia tra i processi e la capacità di controllare la formazione di prodotti pericolosi. La sinergia viene massimizzata ad un valore ottimale di delta, mentre la formazione dei prodotti indesiderati viene controllata operando secondo le procedure che sono state individuate.

Essays on the political economy of European integration

Recently, a rising interest in political and economic integration/disintegration issues has been developed in the political economy field. This growing strand of literature partly draws on traditional issues of fiscal federalism and optimum public good provision and focuses on a trade-off between the benefits of centralization, arising from economies of scale or externalities, and the costs of harmonizing policies as a consequence of the increased heterogeneity of individual preferences in an international union or in a country composed of at least two regions. This thesis stems from this strand of literature and aims to shed some light on two highly relevant aspects of the political economy of European integration. The first concerns the role of public opinion in the integration process; more precisely, how economic benefits and costs of integration shape citizens' support for European Union (EU) membership. The second is the allocation of policy competences among different levels of government: European, national and regional. Chapter 1 introduces the topics developed in this thesis by reviewing the main recent theoretical developments in the political economy analysis of integration processes. It is structured as follows. First, it briefly surveys a few relevant articles on economic theories of integration and disintegration processes (Alesina and Spolaore 1997, Bolton and Roland 1997, Alesina et al. 2000, Casella and Feinstein 2002) and discusses their relevance for the study of the impact of economic benefits and costs on public opinion attitude towards the EU. Subsequently, it explores the links existing between such political economy literature and theories of fiscal federalism, especially with regard to normative considerations concerning the optimal allocation of competences in a union. Chapter 2 firstly proposes a model of citizens’ support for membership of international unions, with explicit reference to the EU; subsequently it tests the model on a panel of EU countries. What are the factors that influence public opinion support for the European Union (EU)? In international relations theory, the idea that citizens' support for the EU depends on material benefits deriving from integration, i.e. whether European integration makes individuals economically better off (utilitarian support), has been common since the 1970s, but has never been the subject of a formal treatment (Hix 2005). A small number of studies in the 1990s have investigated econometrically the link between national economic performance and mass support for European integration (Eichenberg and Dalton 1993; Anderson and Kalthenthaler 1996), but only making informal assumptions. The main aim of Chapter 2 is thus to propose and test our model with a view to providing a more complete and theoretically grounded picture of public support for the EU. Following theories of utilitarian support, we assume that citizens are in favour of membership if they receive economic benefits from it. To develop this idea, we propose a simple political economic model drawing on the recent economic literature on integration and disintegration processes. The basic element is the existence of a trade-off between the benefits of centralisation and the costs of harmonising policies in presence of heterogeneous preferences among countries. The approach we follow is that of the recent literature on the political economy of international unions and the unification or break-up of nations (Bolton and Roland 1997, Alesina and Wacziarg 1999, Alesina et al. 2001, 2005a, to mention only the relevant). The general perspective is that unification provides returns to scale in the provision of public goods, but reduces each member state’s ability to determine its most favoured bundle of public goods. In the simple model presented in Chapter 2, support for membership of the union is increasing in the union’s average income and in the loss of efficiency stemming from being outside the union, and decreasing in a country’s average income, while increasing heterogeneity of preferences among countries points to a reduced scope of the union. Afterwards we empirically test the model with data on the EU; more precisely, we perform an econometric analysis employing a panel of member countries over time. The second part of Chapter 2 thus tries to answer the following question: does public opinion support for the EU really depend on economic factors? The findings are broadly consistent with our theoretical expectations: the conditions of the national economy, differences in income among member states and heterogeneity of preferences shape citizens’ attitude towards their country’s membership of the EU. Consequently, this analysis offers some interesting policy implications for the present debate about ratification of the European Constitution and, more generally, about how the EU could act in order to gain more support from the European public. Citizens in many member states are called to express their opinion in national referenda, which may well end up in rejection of the Constitution, as recently happened in France and the Netherlands, triggering a European-wide political crisis. These events show that nowadays understanding public attitude towards the EU is not only of academic interest, but has a strong relevance for policy-making too. Chapter 3 empirically investigates the link between European integration and regional autonomy in Italy. Over the last few decades, the double tendency towards supranationalism and regional autonomy, which has characterised some European States, has taken a very interesting form in this country, because Italy, besides being one of the founding members of the EU, also implemented a process of decentralisation during the 1970s, further strengthened by a constitutional reform in 2001. Moreover, the issue of the allocation of competences among the EU, the Member States and the regions is now especially topical. The process leading to the drafting of European Constitution (even if then it has not come into force) has attracted much attention from a constitutional political economy perspective both on a normative and positive point of view (Breuss and Eller 2004, Mueller 2005). The Italian parliament has recently passed a new thorough constitutional reform, still to be approved by citizens in a referendum, which includes, among other things, the so called “devolution”, i.e. granting the regions exclusive competence in public health care, education and local police. Following and extending the methodology proposed in a recent influential article by Alesina et al. (2005b), which only concentrated on the EU activity (treaties, legislation, and European Court of Justice’s rulings), we develop a set of quantitative indicators measuring the intensity of the legislative activity of the Italian State, the EU and the Italian regions from 1973 to 2005 in a large number of policy categories. By doing so, we seek to answer the following broad questions. Are European and regional legislations substitutes for state laws? To what extent are the competences attributed by the European treaties or the Italian Constitution actually exerted in the various policy areas? Is their exertion consistent with the normative recommendations from the economic literature about their optimum allocation among different levels of government? The main results show that, first, there seems to be a certain substitutability between EU and national legislations (even if not a very strong one), but not between regional and national ones. Second, the EU concentrates its legislative activity mainly in international trade and agriculture, whilst social policy is where the regions and the State (which is also the main actor in foreign policy) are more active. Third, at least two levels of government (in some cases all of them) are significantly involved in the legislative activity in many sectors, even where the rationale for that is, at best, very questionable, indicating that they actually share a larger number of policy tasks than that suggested by the economic theory. It appears therefore that an excessive number of competences are actually shared among different levels of government. From an economic perspective, it may well be recommended that some competences be shared, but only when the balance between scale or spillover effects and heterogeneity of preferences suggests so. When, on the contrary, too many levels of government are involved in a certain policy area, the distinction between their different responsibilities easily becomes unnecessarily blurred. This may not only leads to a slower and inefficient policy-making process, but also risks to make it too complicate to understand for citizens, who, on the contrary, should be able to know who is really responsible for a certain policy when they vote in national,local or European elections or in referenda on national or European constitutional issues.

Automatic code generation: from process algebraic architectural descriptions to multithreaded java programs

Process algebraic architectural description languages provide a formal means for modeling software systems and assessing their properties. In order to bridge the gap between system modeling and system im- plementation, in this thesis an approach is proposed for automatically generating multithreaded object-oriented code from process algebraic architectural descriptions, in a way that preserves – under certain assumptions – the properties proved at the architectural level. The approach is divided into three phases, which are illustrated by means of a running example based on an audio processing system. First, we develop an architecture-driven technique for thread coordination management, which is completely automated through a suitable package. Second, we address the translation of the algebraically-specified behavior of the individual software units into thread templates, which will have to be filled in by the software developer according to certain guidelines. Third, we discuss performance issues related to the suitability of synthesizing monitors rather than threads from software unit descriptions that satisfy specific constraints. In addition to the running example, we present two case studies about a video animation repainting system and the implementation of a leader election algorithm, in order to summarize the whole approach. The outcome of this thesis is the implementation of the proposed approach in a translator called PADL2Java and its integration in the architecture-centric verification tool TwoTowers.

Biomass Gasification - Process analysis and dimensioning aspects for downdraft units and gas cleaning lines

In such territories where food production is mostly scattered in several small / medium size or even domestic farms, a lot of heterogeneous residues are produced yearly, since farmers usually carry out different activities in their properties. The amount and composition of farm residues, therefore, widely change during year, according to the single production process periodically achieved. Coupling high efficiency micro-cogeneration energy units with easy handling biomass conversion equipments, suitable to treat different materials, would provide many important advantages to the farmers and to the community as well, so that the increase in feedstock flexibility of gasification units is nowadays seen as a further paramount step towards their wide spreading in rural areas and as a real necessity for their utilization at small scale. Two main research topics were thought to be of main concern at this purpose, and they were therefore discussed in this work: the investigation of fuels properties impact on gasification process development and the technical feasibility of small scale gasification units integration with cogeneration systems. According to these two main aspects, the present work was thus divided in two main parts. The first one is focused on the biomass gasification process, that was investigated in its theoretical aspects and then analytically modelled in order to simulate thermo-chemical conversion of different biomass fuels, such as wood (park waste wood and softwood), wheat straw, sewage sludge and refuse derived fuels. The main idea is to correlate the results of reactor design procedures with the physical properties of biomasses and the corresponding working conditions of gasifiers (temperature profile, above all), in order to point out the main differences which prevent the use of the same conversion unit for different materials. At this scope, a gasification kinetic free model was initially developed in Excel sheets, considering different values of air to biomass ratio and the downdraft gasification technology as particular examined application. The differences in syngas production and working conditions (process temperatures, above all) among the considered fuels were tried to be connected to some biomass properties, such elementary composition, ash and water contents. The novelty of this analytical approach was the use of kinetic constants ratio in order to determine oxygen distribution among the different oxidation reactions (regarding volatile matter only) while equilibrium of water gas shift reaction was considered in gasification zone, by which the energy and mass balances involved in the process algorithm were linked together, as well. Moreover, the main advantage of this analytical tool is the easiness by which the input data corresponding to the particular biomass materials can be inserted into the model, so that a rapid evaluation on their own thermo-chemical conversion properties is possible to be obtained, mainly based on their chemical composition A good conformity of the model results with the other literature and experimental data was detected for almost all the considered materials (except for refuse derived fuels, because of their unfitting chemical composition with the model assumptions). Successively, a dimensioning procedure for open core downdraft gasifiers was set up, by the analysis on the fundamental thermo-physical and thermo-chemical mechanisms which are supposed to regulate the main solid conversion steps involved in the gasification process. Gasification units were schematically subdivided in four reaction zones, respectively corresponding to biomass heating, solids drying, pyrolysis and char gasification processes, and the time required for the full development of each of these steps was correlated to the kinetics rates (for pyrolysis and char gasification processes only) and to the heat and mass transfer phenomena from gas to solid phase. On the basis of this analysis and according to the kinetic free model results and biomass physical properties (particles size, above all) it was achieved that for all the considered materials char gasification step is kinetically limited and therefore temperature is the main working parameter controlling this step. Solids drying is mainly regulated by heat transfer from bulk gas to the inner layers of particles and the corresponding time especially depends on particle size. Biomass heating is almost totally achieved by the radiative heat transfer from the hot walls of reactor to the bed of material. For pyrolysis, instead, working temperature, particles size and the same nature of biomass (through its own pyrolysis heat) have all comparable weights on the process development, so that the corresponding time can be differently depending on one of these factors according to the particular fuel is gasified and the particular conditions are established inside the gasifier. The same analysis also led to the estimation of reaction zone volumes for each biomass fuel, so as a comparison among the dimensions of the differently fed gasification units was finally accomplished. Each biomass material showed a different volumes distribution, so that any dimensioned gasification unit does not seem to be suitable for more than one biomass species. Nevertheless, since reactors diameters were found out quite similar for all the examined materials, it could be envisaged to design a single units for all of them by adopting the largest diameter and by combining together the maximum heights of each reaction zone, as they were calculated for the different biomasses. A total height of gasifier as around 2400mm would be obtained in this case. Besides, by arranging air injecting nozzles at different levels along the reactor, gasification zone could be properly set up according to the particular material is in turn gasified. Finally, since gasification and pyrolysis times were found to considerably change according to even short temperature variations, it could be also envisaged to regulate air feeding rate for each gasified material (which process temperatures depend on), so as the available reactor volumes would be suitable for the complete development of solid conversion in each case, without even changing fluid dynamics behaviour of the unit as well as air/biomass ratio in noticeable measure. The second part of this work dealt with the gas cleaning systems to be adopted downstream the gasifiers in order to run high efficiency CHP units (i.e. internal engines and micro-turbines). Especially in the case multi–fuel gasifiers are assumed to be used, weightier gas cleaning lines need to be envisaged in order to reach the standard gas quality degree required to fuel cogeneration units. Indeed, as the more heterogeneous feed to the gasification unit, several contaminant species can simultaneously be present in the exit gas stream and, as a consequence, suitable gas cleaning systems have to be designed. In this work, an overall study on gas cleaning lines assessment is carried out. Differently from the other research efforts carried out in the same field, the main scope is to define general arrangements for gas cleaning lines suitable to remove several contaminants from the gas stream, independently on the feedstock material and the energy plant size The gas contaminant species taken into account in this analysis were: particulate, tars, sulphur (in H2S form), alkali metals, nitrogen (in NH3 form) and acid gases (in HCl form). For each of these species, alternative cleaning devices were designed according to three different plant sizes, respectively corresponding with 8Nm3/h, 125Nm3/h and 350Nm3/h gas flows. Their performances were examined on the basis of their optimal working conditions (efficiency, temperature and pressure drops, above all) and their own consumption of energy and materials. Successively, the designed units were combined together in different overall gas cleaning line arrangements, paths, by following some technical constraints which were mainly determined from the same performance analysis on the cleaning units and from the presumable synergic effects by contaminants on the right working of some of them (filters clogging, catalysts deactivation, etc.). One of the main issues to be stated in paths design accomplishment was the tars removal from the gas stream, preventing filters plugging and/or line pipes clogging At this scope, a catalytic tars cracking unit was envisaged as the only solution to be adopted, and, therefore, a catalytic material which is able to work at relatively low temperatures was chosen. Nevertheless, a rapid drop in tars cracking efficiency was also estimated for this same material, so that an high frequency of catalysts regeneration and a consequent relevant air consumption for this operation were calculated in all of the cases. Other difficulties had to be overcome in the abatement of alkali metals, which condense at temperatures lower than tars, but they also need to be removed in the first sections of gas cleaning line in order to avoid corrosion of materials. In this case a dry scrubber technology was envisaged, by using the same fine particles filter units and by choosing for them corrosion resistant materials, like ceramic ones. Besides these two solutions which seem to be unavoidable in gas cleaning line design, high temperature gas cleaning lines were not possible to be achieved for the two larger plant sizes, as well. Indeed, as the use of temperature control devices was precluded in the adopted design procedure, ammonia partial oxidation units (as the only considered methods for the abatement of ammonia at high temperature) were not suitable for the large scale units, because of the high increase of reactors temperature by the exothermic reactions involved in the process. In spite of these limitations, yet, overall arrangements for each considered plant size were finally designed, so that the possibility to clean the gas up to the required standard degree was technically demonstrated, even in the case several contaminants are simultaneously present in the gas stream. Moreover, all the possible paths defined for the different plant sizes were compared each others on the basis of some defined operational parameters, among which total pressure drops, total energy losses, number of units and secondary materials consumption. On the basis of this analysis, dry gas cleaning methods proved preferable to the ones including water scrubber technology in al of the cases, especially because of the high water consumption provided by water scrubber units in ammonia adsorption process. This result is yet connected to the possibility to use activated carbon units for ammonia removal and Nahcolite adsorber for chloride acid. The very high efficiency of this latter material is also remarkable. Finally, as an estimation of the overall energy loss pertaining the gas cleaning process, the total enthalpy losses estimated for the three plant sizes were compared with the respective gas streams energy contents, these latter obtained on the basis of low heating value of gas only. This overall study on gas cleaning systems is thus proposed as an analytical tool by which different gas cleaning line configurations can be evaluated, according to the particular practical application they are adopted for and the size of cogeneration unit they are connected to.

Integration of MFA and LCA methodologies: the anthropogenic aluminium cycle in Italy

MFA and LCA methodologies were applied to analyse the anthropogenic aluminium cycle in Italy with focus on historical evolution of stocks and flows of the metal, embodied GHG emissions, and potentials from recycling to provide key features to Italy for prioritizing industrial policy toward low-carbon technologies and materials. Historical trend series were collected from 1947 to 2009 and balanced with data from production, manufacturing and waste management of aluminium-containing products, using a ‘top-down’ approach to quantify the contemporary in-use stock of the metal, and helping to identify ‘applications where aluminium is not yet being recycled to its full potential and to identify present and future recycling flows’. The MFA results were used as a basis for the LCA aimed at evaluating the carbon footprint evolution, from primary and electrical energy, the smelting process and the transportation, embodied in the Italian aluminium. A discussion about how the main factors, according to the Kaya Identity equation, they did influence the Italian GHG emissions pattern over time, and which are the levers to mitigate it, it has been also reported. The contemporary anthropogenic reservoirs of aluminium was estimated at about 320 kg per capita, mainly embedded within the transportation and building and construction sectors. Cumulative in-use stock represents approximately 11 years of supply at current usage rates (about 20 Mt versus 1.7 Mt/year), and it would imply a potential of about 160 Mt of CO2eq emissions savings. A discussion of criticality related to aluminium waste recovery from the transportation and the containers and packaging sectors was also included in the study, providing an example for how MFA and LCA may support decision-making at sectorial or regional level. The research constitutes the first attempt of an integrated approach between MFA and LCA applied to the aluminium cycle in Italy.

Development of methodologies supporting the sustainable and safe integration of offshore conventional and renewable energy production

Against a backdrop of rapidly increasing worldwide population and growing energy demand, the development of renewable energy technologies has become of primary importance in the effort to reduce greenhouse gas emissions. However, it is often technically and economically infeasible to transport discontinuous renewable electricity for long distances to the shore. Another shortcoming of non-programmable renewable power is its integration into the onshore grid without affecting the dispatching process. On the other hand, the offshore oil & gas industry is striving to reduce overall carbon footprint from onsite power generators and limiting large expenses associated to carrying electricity from remote offshore facilities. Furthermore, the increased complexity and expansion towards challenging areas of offshore hydrocarbons operations call for higher attention to safety and environmental protection issues from major accident hazards. Innovative hybrid energy systems, as Power-to-Gas (P2G), Power-to-Liquid (P2L) and Gas-to-Power (G2P) options, implemented at offshore locations, would offer the opportunity to overcome challenges of both renewable and oil & gas sectors. This study aims at the development of systematic methodologies based on proper sustainability and safety performance indicators supporting the choice of P2G, P2L and G2P hybrid energy options for offshore green projects in early design phases. An in-depth analysis of the different offshore hybrid strategies was performed. The literature reviews on existing methods proposing metrics to assess sustainability of hybrid energy systems, inherent safety of process routes in conceptual design stage and environmental protection of installations from oil and chemical accidental spills were carried out. To fill the gaps, a suite of specific decision-making methodologies was developed, based on representative multi-criteria indicators addressing technical, economic, environmental and societal aspects of alternative options. A set of five case-studies was defined, covering different offshore scenarios of concern, to provide an assessment of the effectiveness and value of the developed tools.

Towards Unstructured Knowledge Integration in Natural Language Processing

In the last decades, Artificial Intelligence has witnessed multiple breakthroughs in deep learning. In particular, purely data-driven approaches have opened to a wide variety of successful applications due to the large availability of data. Nonetheless, the integration of prior knowledge is still required to compensate for specific issues like lack of generalization from limited data, fairness, robustness, and biases. In this thesis, we analyze the methodology of integrating knowledge into deep learning models in the field of Natural Language Processing (NLP). We start by remarking on the importance of knowledge integration. We highlight the possible shortcomings of these approaches and investigate the implications of integrating unstructured textual knowledge. We introduce Unstructured Knowledge Integration (UKI) as the process of integrating unstructured knowledge into machine learning models. We discuss UKI in the field of NLP, where knowledge is represented in a natural language format. We identify UKI as a complex process comprised of multiple sub-processes, different knowledge types, and knowledge integration properties to guarantee. We remark on the challenges of integrating unstructured textual knowledge and bridge connections with well-known research areas in NLP. We provide a unified vision of structured knowledge extraction (KE) and UKI by identifying KE as a sub-process of UKI. We investigate some challenging scenarios where structured knowledge is not a feasible prior assumption and formulate each task from the point of view of UKI. We adopt simple yet effective neural architectures and discuss the challenges of such an approach. Finally, we identify KE as a form of symbolic representation. From this perspective, we remark on the need of defining sophisticated UKI processes to verify the validity of knowledge integration. To this end, we foresee frameworks capable of combining symbolic and sub-symbolic representations for learning as a solution.

The integration of immigrant-origin youths in Japan

The steadily growing immigration phenomenon in today’s Japan is showing a tangible and expanding presence of immigrant-origin youths residing in the country. International research in the migration studies area has underlined the importance of focusing on immigrant-origin youths to shed light on the character of the way immigrant incorporate in countries of destinations. In-deed, immigrants’ offspring, the adults of tomorrow, embody the interlocutor between first-generation immigrants and the receiving societal context. The extent of the presence of immigrants’ children in countries of destination is also a reliable yardstick to assess the maturation of the migration process, transforming it from a temporary phenomenon to a long-term settlement. Within this framework, the school is a privileged site to observe and analyze immigrant-origin youths’ integration. Alongside their family and peers, school constitutes one of the main agents of socialization. Here, children learn norms and rules and acquire the necessary tools to eventually compete in the pursuit of an occupation, determining their future socioeconomic standing. This doctoral research aims to identify which theoretical model articulated in the area of migration studies best describes the adaptation process of immigrant-origin youths in Japan. In particular, it examines whether (and to what extent) any of the pre-existing frameworks can help explain the Japanese occurring circumstances, or whether further elaboration and adjustment are needed. Alternatively, it studies whether it is necessary to produce a new model based on the peculiarities of the Japanese social context. This study provides a theoretical-oriented contribution to the (mainly descriptive but maturing) literature on immigrant-origin youths’ integration in Japan. Considering past growth trends of Japanese immigration and its expanding prospective projections (Korekawa 2018c), this study might be considered pioneering for future development of the phenomenon.