The APSEL4D Monolithic Active Pixel Sensor and its Usage in a Single Electron Interference Experiment

We have realized a Data Acquisition chain for the use and characterization of APSEL4D, a 32 x 128 Monolithic Active Pixel Sensor, developed as a prototype for frontier experiments in high energy particle physics. In particular a transition board was realized for the conversion between the chip and the FPGA voltage levels and for the signal quality enhancing. A Xilinx Spartan-3 FPGA was used for real time data processing, for the chip control and the communication with a Personal Computer through a 2.0 USB port. For this purpose a firmware code, developed in VHDL language, was written. Finally a Graphical User Interface for the online system monitoring, hit display and chip control, based on windows and widgets, was realized developing a C++ code and using Qt and Qwt dedicated libraries. APSEL4D and the full acquisition chain were characterized for the first time with the electron beam of the transmission electron microscope and with 55Fe and 90Sr radioactive sources. In addition, a beam test was performed at the T9 station of the CERN PS, where hadrons of momentum of 12 GeV/c are available. The very high time resolution of APSEL4D (up to 2.5 Mfps, but used at 6 kfps) was fundamental in realizing a single electron Young experiment using nanometric double slits obtained by a FIB technique. On high statistical samples, it was possible to observe the interference and diffractions of single isolated electrons traveling inside a transmission electron microscope. For the first time, the information on the distribution of the arrival time of the single electrons has been extracted.

Tecniche per il controllo dinamico del consumo di potenza per piattaforme system-on-chip

Providing support for multimedia applications on low-power mobile devices remains a significant research challenge. This is primarily due to two reasons: • Portable mobile devices have modest sizes and weights, and therefore inadequate resources, low CPU processing power, reduced display capabilities, limited memory and battery lifetimes as compared to desktop and laptop systems. • On the other hand, multimedia applications tend to have distinctive QoS and processing requirementswhichmake themextremely resource-demanding. This innate conflict introduces key research challenges in the design of multimedia applications and device-level power optimization. Energy efficiency in this kind of platforms can be achieved only via a synergistic hardware and software approach. In fact, while System-on-Chips are more and more programmable thus providing functional flexibility, hardwareonly power reduction techniques cannot maintain consumption under acceptable bounds. It is well understood both in research and industry that system configuration andmanagement cannot be controlled efficiently only relying on low-level firmware and hardware drivers. In fact, at this level there is lack of information about user application activity and consequently about the impact of power management decision on QoS. Even though operating system support and integration is a requirement for effective performance and energy management, more effective and QoSsensitive power management is possible if power awareness and hardware configuration control strategies are tightly integratedwith domain-specificmiddleware services. The main objective of this PhD research has been the exploration and the integration of amiddleware-centric energymanagement with applications and operating-system. We choose to focus on the CPU-memory and the video subsystems, since they are the most power-hungry components of an embedded system. A second main objective has been the definition and implementation of software facilities (like toolkits, API, and run-time engines) in order to improve programmability and performance efficiency of such platforms. Enhancing energy efficiency and programmability ofmodernMulti-Processor System-on-Chips (MPSoCs) Consumer applications are characterized by tight time-to-market constraints and extreme cost sensitivity. The software that runs on modern embedded systems must be high performance, real time, and even more important low power. Although much progress has been made on these problems, much remains to be done. Multi-processor System-on-Chip (MPSoC) are increasingly popular platforms for high performance embedded applications. This leads to interesting challenges in software development since efficient software development is a major issue for MPSoc designers. An important step in deploying applications on multiprocessors is to allocate and schedule concurrent tasks to the processing and communication resources of the platform. The problem of allocating and scheduling precedenceconstrained tasks on processors in a distributed real-time system is NP-hard. There is a clear need for deployment technology that addresses thesemulti processing issues. This problem can be tackled by means of specific middleware which takes care of allocating and scheduling tasks on the different processing elements and which tries also to optimize the power consumption of the entire multiprocessor platform. This dissertation is an attempt to develop insight into efficient, flexible and optimalmethods for allocating and scheduling concurrent applications tomultiprocessor architectures. It is a well-known problem in literature: this kind of optimization problems are very complex even in much simplified variants, therefore most authors propose simplified models and heuristic approaches to solve it in reasonable time. Model simplification is often achieved by abstracting away platform implementation ”details”. As a result, optimization problems become more tractable, even reaching polynomial time complexity. Unfortunately, this approach creates an abstraction gap between the optimization model and the real HW-SW platform. The main issue with heuristic or, more in general, with incomplete search is that they introduce an optimality gap of unknown size. They provide very limited or no information on the distance between the best computed solution and the optimal one. The goal of this work is to address both abstraction and optimality gaps, formulating accurate models which accounts for a number of ”non-idealities” in real-life hardware platforms, developing novel mapping algorithms that deterministically find optimal solutions, and implementing software infrastructures required by developers to deploy applications for the targetMPSoC platforms. Energy Efficient LCDBacklightAutoregulation on Real-LifeMultimediaAp- plication Processor Despite the ever increasing advances in Liquid Crystal Display’s (LCD) technology, their power consumption is still one of the major limitations to the battery life of mobile appliances such as smart phones, portable media players, gaming and navigation devices. There is a clear trend towards the increase of LCD size to exploit the multimedia capabilities of portable devices that can receive and render high definition video and pictures. Multimedia applications running on these devices require LCD screen sizes of 2.2 to 3.5 inches andmore to display video sequences and pictures with the required quality. LCD power consumption is dependent on the backlight and pixel matrix driving circuits and is typically proportional to the panel area. As a result, the contribution is also likely to be considerable in future mobile appliances. To address this issue, companies are proposing low power technologies suitable for mobile applications supporting low power states and image control techniques. On the research side, several power saving schemes and algorithms can be found in literature. Some of them exploit software-only techniques to change the image content to reduce the power associated with the crystal polarization, some others are aimed at decreasing the backlight level while compensating the luminance reduction by compensating the user perceived quality degradation using pixel-by-pixel image processing algorithms. The major limitation of these techniques is that they rely on the CPU to perform pixel-based manipulations and their impact on CPU utilization and power consumption has not been assessed. This PhDdissertation shows an alternative approach that exploits in a smart and efficient way the hardware image processing unit almost integrated in every current multimedia application processors to implement a hardware assisted image compensation that allows dynamic scaling of the backlight with a negligible impact on QoS. The proposed approach overcomes CPU-intensive techniques by saving system power without requiring either a dedicated display technology or hardware modification. Thesis Overview The remainder of the thesis is organized as follows. The first part is focused on enhancing energy efficiency and programmability of modern Multi-Processor System-on-Chips (MPSoCs). Chapter 2 gives an overview about architectural trends in embedded systems, illustrating the principal features of new technologies and the key challenges still open. Chapter 3 presents a QoS-driven methodology for optimal allocation and frequency selection for MPSoCs. The methodology is based on functional simulation and full system power estimation. Chapter 4 targets allocation and scheduling of pipelined stream-oriented applications on top of distributed memory architectures with messaging support. We tackled the complexity of the problem by means of decomposition and no-good generation, and prove the increased computational efficiency of this approach with respect to traditional ones. Chapter 5 presents a cooperative framework to solve the allocation, scheduling and voltage/frequency selection problem to optimality for energyefficient MPSoCs, while in Chapter 6 applications with conditional task graph are taken into account. Finally Chapter 7 proposes a complete framework, called Cellflow, to help programmers in efficient software implementation on a real architecture, the Cell Broadband Engine processor. The second part is focused on energy efficient software techniques for LCD displays. Chapter 8 gives an overview about portable device display technologies, illustrating the principal features of LCD video systems and the key challenges still open. Chapter 9 shows several energy efficient software techniques present in literature, while Chapter 10 illustrates in details our method for saving significant power in an LCD panel. Finally, conclusions are drawn, reporting the main research contributions that have been discussed throughout this dissertation.

Il passato nell’epoca della sua (ri)producibilità digitale. Torino 1943 - 45. Metodologia della ricerca con tecnologie informatiche. Sistema storico-territoriale di informazione multimediale

Se il lavoro dello storico è capire il passato come è stato compreso dalla gente che lo ha vissuto, allora forse non è azzardato pensare che sia anche necessario comunicare i risultati delle ricerche con strumenti propri che appartengono a un'epoca e che influenzano la mentalità di chi in quell'epoca vive. Emergenti tecnologie, specialmente nell’area della multimedialità come la realtà virtuale, permettono agli storici di comunicare l’esperienza del passato in più sensi. In che modo la storia collabora con le tecnologie informatiche soffermandosi sulla possibilità di fare ricostruzioni storiche virtuali, con relativi esempi e recensioni? Quello che maggiormente preoccupa gli storici è se una ricostruzione di un fatto passato vissuto attraverso la sua ricreazione in pixels sia un metodo di conoscenza della storia che possa essere considerato valido. Ovvero l'emozione che la navigazione in una realtà 3D può suscitare, è un mezzo in grado di trasmettere conoscenza? O forse l'idea che abbiamo del passato e del suo studio viene sottilmente cambiato nel momento in cui lo si divulga attraverso la grafica 3D? Da tempo però la disciplina ha cominciato a fare i conti con questa situazione, costretta soprattutto dall'invasività di questo tipo di media, dalla spettacolarizzazione del passato e da una divulgazione del passato parziale e antiscientifica. In un mondo post letterario bisogna cominciare a pensare che la cultura visuale nella quale siamo immersi sta cambiando il nostro rapporto con il passato: non per questo le conoscenze maturate fino ad oggi sono false, ma è necessario riconoscere che esiste più di una verità storica, a volte scritta a volte visuale. Il computer è diventato una piattaforma onnipresente per la rappresentazione e diffusione dell’informazione. I metodi di interazione e rappresentazione stanno evolvendo di continuo. Ed è su questi due binari che è si muove l’offerta delle tecnologie informatiche al servizio della storia. Lo scopo di questa tesi è proprio quello di esplorare, attraverso l’utilizzo e la sperimentazione di diversi strumenti e tecnologie informatiche, come si può raccontare efficacemente il passato attraverso oggetti tridimensionali e gli ambienti virtuali, e come, nel loro essere elementi caratterizzanti di comunicazione, in che modo possono collaborare, in questo caso particolare, con la disciplina storica. La presente ricerca ricostruisce alcune linee di storia delle principali fabbriche attive a Torino durante la seconda guerra mondiale, ricordando stretta relazione che esiste tra strutture ed individui e in questa città in particolare tra fabbrica e movimento operaio, è inevitabile addentrarsi nelle vicende del movimento operaio torinese che nel periodo della lotta di Liberazione in città fu un soggetto politico e sociale di primo rilievo. Nella città, intesa come entità biologica coinvolta nella guerra, la fabbrica (o le fabbriche) diventa il nucleo concettuale attraverso il quale leggere la città: sono le fabbriche gli obiettivi principali dei bombardamenti ed è nelle fabbriche che si combatte una guerra di liberazione tra classe operaia e autorità, di fabbrica e cittadine. La fabbrica diventa il luogo di "usurpazione del potere" di cui parla Weber, il palcoscenico in cui si tengono i diversi episodi della guerra: scioperi, deportazioni, occupazioni .... Il modello della città qui rappresentata non è una semplice visualizzazione ma un sistema informativo dove la realtà modellata è rappresentata da oggetti, che fanno da teatro allo svolgimento di avvenimenti con una precisa collocazione cronologica, al cui interno è possibile effettuare operazioni di selezione di render statici (immagini), di filmati precalcolati (animazioni) e di scenari navigabili interattivamente oltre ad attività di ricerca di fonti bibliografiche e commenti di studiosi segnatamente legati all'evento in oggetto. Obiettivo di questo lavoro è far interagire, attraverso diversi progetti, le discipline storiche e l’informatica, nelle diverse opportunità tecnologiche che questa presenta. Le possibilità di ricostruzione offerte dal 3D vengono così messe a servizio della ricerca, offrendo una visione integrale in grado di avvicinarci alla realtà dell’epoca presa in considerazione e convogliando in un’unica piattaforma espositiva tutti i risultati. Divulgazione Progetto Mappa Informativa Multimediale Torino 1945 Sul piano pratico il progetto prevede una interfaccia navigabile (tecnologia Flash) che rappresenti la pianta della città dell’epoca, attraverso la quale sia possibile avere una visione dei luoghi e dei tempi in cui la Liberazione prese forma, sia a livello concettuale, sia a livello pratico. Questo intreccio di coordinate nello spazio e nel tempo non solo migliora la comprensione dei fenomeni, ma crea un maggiore interesse sull’argomento attraverso l’utilizzo di strumenti divulgativi di grande efficacia (e appeal) senza perdere di vista la necessità di valicare le tesi storiche proponendosi come piattaforma didattica. Un tale contesto richiede uno studio approfondito degli eventi storici al fine di ricostruire con chiarezza una mappa della città che sia precisa sia topograficamente sia a livello di navigazione multimediale. La preparazione della cartina deve seguire gli standard del momento, perciò le soluzioni informatiche utilizzate sono quelle fornite da Adobe Illustrator per la realizzazione della topografia, e da Macromedia Flash per la creazione di un’interfaccia di navigazione. La base dei dati descrittivi è ovviamente consultabile essendo contenuta nel supporto media e totalmente annotata nella bibliografia. È il continuo evolvere delle tecnologie d'informazione e la massiccia diffusione dell’uso dei computer che ci porta a un cambiamento sostanziale nello studio e nell’apprendimento storico; le strutture accademiche e gli operatori economici hanno fatto propria la richiesta che giunge dall'utenza (insegnanti, studenti, operatori dei Beni Culturali) di una maggiore diffusione della conoscenza storica attraverso la sua rappresentazione informatizzata. Sul fronte didattico la ricostruzione di una realtà storica attraverso strumenti informatici consente anche ai non-storici di toccare con mano quelle che sono le problematiche della ricerca quali fonti mancanti, buchi della cronologia e valutazione della veridicità dei fatti attraverso prove. Le tecnologie informatiche permettono una visione completa, unitaria ed esauriente del passato, convogliando tutte le informazioni su un'unica piattaforma, permettendo anche a chi non è specializzato di comprendere immediatamente di cosa si parla. Il miglior libro di storia, per sua natura, non può farlo in quanto divide e organizza le notizie in modo diverso. In questo modo agli studenti viene data l'opportunità di apprendere tramite una rappresentazione diversa rispetto a quelle a cui sono abituati. La premessa centrale del progetto è che i risultati nell'apprendimento degli studenti possono essere migliorati se un concetto o un contenuto viene comunicato attraverso più canali di espressione, nel nostro caso attraverso un testo, immagini e un oggetto multimediale. Didattica La Conceria Fiorio è uno dei luoghi-simbolo della Resistenza torinese. Il progetto è una ricostruzione in realtà virtuale della Conceria Fiorio di Torino. La ricostruzione serve a arricchire la cultura storica sia a chi la produce, attraverso una ricerca accurata delle fonti, sia a chi può poi usufruirne, soprattutto i giovani, che, attratti dall’aspetto ludico della ricostruzione, apprendono con più facilità. La costruzione di un manufatto in 3D fornisce agli studenti le basi per riconoscere ed esprimere la giusta relazione fra il modello e l’oggetto storico. Le fasi di lavoro attraverso cui si è giunti alla ricostruzione in 3D della Conceria: . una ricerca storica approfondita, basata sulle fonti, che possono essere documenti degli archivi o scavi archeologici, fonti iconografiche, cartografiche, ecc.; . La modellazione degli edifici sulla base delle ricerche storiche, per fornire la struttura geometrica poligonale che permetta la navigazione tridimensionale; . La realizzazione, attraverso gli strumenti della computer graphic della navigazione in 3D. Unreal Technology è il nome dato al motore grafico utilizzato in numerosi videogiochi commerciali. Una delle caratteristiche fondamentali di tale prodotto è quella di avere uno strumento chiamato Unreal editor con cui è possibile costruire mondi virtuali, e che è quello utilizzato per questo progetto. UnrealEd (Ued) è il software per creare livelli per Unreal e i giochi basati sul motore di Unreal. E’ stata utilizzata la versione gratuita dell’editor. Il risultato finale del progetto è un ambiente virtuale navigabile raffigurante una ricostruzione accurata della Conceria Fiorio ai tempi della Resistenza. L’utente può visitare l’edificio e visualizzare informazioni specifiche su alcuni punti di interesse. La navigazione viene effettuata in prima persona, un processo di “spettacolarizzazione” degli ambienti visitati attraverso un arredamento consono permette all'utente una maggiore immersività rendendo l’ambiente più credibile e immediatamente codificabile. L’architettura Unreal Technology ha permesso di ottenere un buon risultato in un tempo brevissimo, senza che fossero necessari interventi di programmazione. Questo motore è, quindi, particolarmente adatto alla realizzazione rapida di prototipi di una discreta qualità, La presenza di un certo numero di bug lo rende, però, in parte inaffidabile. Utilizzare un editor da videogame per questa ricostruzione auspica la possibilità di un suo impiego nella didattica, quello che le simulazioni in 3D permettono nel caso specifico è di permettere agli studenti di sperimentare il lavoro della ricostruzione storica, con tutti i problemi che lo storico deve affrontare nel ricreare il passato. Questo lavoro vuole essere per gli storici una esperienza nella direzione della creazione di un repertorio espressivo più ampio, che includa gli ambienti tridimensionali. Il rischio di impiegare del tempo per imparare come funziona questa tecnologia per generare spazi virtuali rende scettici quanti si impegnano nell'insegnamento, ma le esperienze di progetti sviluppati, soprattutto all’estero, servono a capire che sono un buon investimento. Il fatto che una software house, che crea un videogame di grande successo di pubblico, includa nel suo prodotto, una serie di strumenti che consentano all'utente la creazione di mondi propri in cui giocare, è sintomatico che l'alfabetizzazione informatica degli utenti medi sta crescendo sempre più rapidamente e che l'utilizzo di un editor come Unreal Engine sarà in futuro una attività alla portata di un pubblico sempre più vasto. Questo ci mette nelle condizioni di progettare moduli di insegnamento più immersivi, in cui l'esperienza della ricerca e della ricostruzione del passato si intreccino con lo studio più tradizionale degli avvenimenti di una certa epoca. I mondi virtuali interattivi vengono spesso definiti come la forma culturale chiave del XXI secolo, come il cinema lo è stato per il XX. Lo scopo di questo lavoro è stato quello di suggerire che vi sono grosse opportunità per gli storici impiegando gli oggetti e le ambientazioni in 3D, e che essi devono coglierle. Si consideri il fatto che l’estetica abbia un effetto sull’epistemologia. O almeno sulla forma che i risultati delle ricerche storiche assumono nel momento in cui devono essere diffuse. Un’analisi storica fatta in maniera superficiale o con presupposti errati può comunque essere diffusa e avere credito in numerosi ambienti se diffusa con mezzi accattivanti e moderni. Ecco perchè non conviene seppellire un buon lavoro in qualche biblioteca, in attesa che qualcuno lo scopra. Ecco perchè gli storici non devono ignorare il 3D. La nostra capacità, come studiosi e studenti, di percepire idee ed orientamenti importanti dipende spesso dai metodi che impieghiamo per rappresentare i dati e l’evidenza. Perché gli storici possano ottenere il beneficio che il 3D porta con sè, tuttavia, devono sviluppare un’agenda di ricerca volta ad accertarsi che il 3D sostenga i loro obiettivi di ricercatori e insegnanti. Una ricostruzione storica può essere molto utile dal punto di vista educativo non sono da chi la visita ma, anche da chi la realizza. La fase di ricerca necessaria per la ricostruzione non può fare altro che aumentare il background culturale dello sviluppatore. Conclusioni La cosa più importante è stata la possibilità di fare esperienze nell’uso di mezzi di comunicazione di questo genere per raccontare e far conoscere il passato. Rovesciando il paradigma conoscitivo che avevo appreso negli studi umanistici, ho cercato di desumere quelle che potremo chiamare “leggi universali” dai dati oggettivi emersi da questi esperimenti. Da punto di vista epistemologico l’informatica, con la sua capacità di gestire masse impressionanti di dati, dà agli studiosi la possibilità di formulare delle ipotesi e poi accertarle o smentirle tramite ricostruzioni e simulazioni. Il mio lavoro è andato in questa direzione, cercando conoscere e usare strumenti attuali che nel futuro avranno sempre maggiore presenza nella comunicazione (anche scientifica) e che sono i mezzi di comunicazione d’eccellenza per determinate fasce d’età (adolescenti). Volendo spingere all’estremo i termini possiamo dire che la sfida che oggi la cultura visuale pone ai metodi tradizionali del fare storia è la stessa che Erodoto e Tucidide contrapposero ai narratori di miti e leggende. Prima di Erodoto esisteva il mito, che era un mezzo perfettamente adeguato per raccontare e dare significato al passato di una tribù o di una città. In un mondo post letterario la nostra conoscenza del passato sta sottilmente mutando nel momento in cui lo vediamo rappresentato da pixel o quando le informazioni scaturiscono non da sole, ma grazie all’interattività con il mezzo. La nostra capacità come studiosi e studenti di percepire idee ed orientamenti importanti dipende spesso dai metodi che impieghiamo per rappresentare i dati e l’evidenza. Perché gli storici possano ottenere il beneficio sottinteso al 3D, tuttavia, devono sviluppare un’agenda di ricerca volta ad accertarsi che il 3D sostenga i loro obiettivi di ricercatori e insegnanti. Le esperienze raccolte nelle pagine precedenti ci portano a pensare che in un futuro non troppo lontano uno strumento come il computer sarà l’unico mezzo attraverso cui trasmettere conoscenze, e dal punto di vista didattico la sua interattività consente coinvolgimento negli studenti come nessun altro mezzo di comunicazione moderno.

A skin surface characterization system based on capacitive image analysis

During the last few years, several methods have been proposed in order to study and to evaluate characteristic properties of the human skin by using non-invasive approaches. Mostly, these methods cover aspects related to either dermatology, to analyze skin physiology and to evaluate the effectiveness of medical treatments in skin diseases, or dermocosmetics and cosmetic science to evaluate, for example, the effectiveness of anti-aging treatments. To these purposes a routine approach must be followed. Although very accurate and high resolution measurements can be achieved by using conventional methods, such as optical or mechanical profilometry for example, their use is quite limited primarily to the high cost of the instrumentation required, which in turn is usually cumbersome, highlighting some of the limitations for a routine based analysis. This thesis aims to investigate the feasibility of a noninvasive skin characterization system based on the analysis of capacitive images of the skin surface. The system relies on a CMOS portable capacitive device which gives 50 micron/pixel resolution capacitance map of the skin micro-relief. In order to extract characteristic features of the skin topography, image analysis techniques, such as watershed segmentation and wavelet analysis, have been used to detect the main structures of interest: wrinkles and plateau of the typical micro-relief pattern. In order to validate the method, the features extracted from a dataset of skin capacitive images acquired during dermatological examinations of a healthy group of volunteers have been compared with the age of the subjects involved, showing good correlation with the skin ageing effect. Detailed analysis of the output of the capacitive sensor compared with optical profilometry of silicone replica of the same skin area has revealed potentiality and some limitations of this technology. Also, applications to follow-up studies, as needed to objectively evaluate the effectiveness of treatments in a routine manner, are discussed.

Applications of High Speed Configurable Logic Devices in Modern Particle Physics Experiments

Several activities were conducted during my PhD activity. For the NEMO experiment a collaboration between the INFN/University groups of Catania and Bologna led to the development and production of a mixed signal acquisition board for the Nemo Km3 telescope. The research concerned the feasibility study for a different acquisition technique quite far from that adopted in the NEMO Phase 1 telescope. The DAQ board that we realized exploits the LIRA06 front-end chip for the analog acquisition of anodic an dynodic sources of a PMT (Photo-Multiplier Tube). The low-power analog acquisition allows to sample contemporaneously multiple channels of the PMT at different gain factors in order to increase the signal response linearity over a wider dynamic range. Also the auto triggering and self-event-classification features help to improve the acquisition performance and the knowledge on the neutrino event. A fully functional interface towards the first level data concentrator, the Floor Control Module, has been integrated as well on the board, and a specific firmware has been realized to comply with the present communication protocols. This stage of the project foresees the use of an FPGA, a high speed configurable device, to provide the board with a flexible digital logic control core. After the validation of the whole front-end architecture this feature would be probably integrated in a common mixed-signal ASIC (Application Specific Integrated Circuit). The volatile nature of the configuration memory of the FPGA implied the integration of a flash ISP (In System Programming) memory and a smart architecture for a safe remote reconfiguration of it. All the integrated features of the board have been tested. At the Catania laboratory the behavior of the LIRA chip has been investigated in the digital environment of the DAQ board and we succeeded in driving the acquisition with the FPGA. The PMT pulses generated with an arbitrary waveform generator were correctly triggered and acquired by the analog chip, and successively they were digitized by the on board ADC under the supervision of the FPGA. For the communication towards the data concentrator a test bench has been realized in Bologna where, thanks to a lending of the Roma University and INFN, a full readout chain equivalent to that present in the NEMO phase-1 was installed. These tests showed a good behavior of the digital electronic that was able to receive and to execute command imparted by the PC console and to answer back with a reply. The remotely configurable logic behaved well too and demonstrated, at least in principle, the validity of this technique. A new prototype board is now under development at the Catania laboratory as an evolution of the one described above. This board is going to be deployed within the NEMO Phase-2 tower in one of its floors dedicated to new front-end proposals. This board will integrate a new analog acquisition chip called SAS (Smart Auto-triggering Sampler) introducing thus a new analog front-end but inheriting most of the digital logic present in the current DAQ board discussed in this thesis. For what concern the activity on high-resolution vertex detectors, I worked within the SLIM5 collaboration for the characterization of a MAPS (Monolithic Active Pixel Sensor) device called APSEL-4D. The mentioned chip is a matrix of 4096 active pixel sensors with deep N-well implantations meant for charge collection and to shield the analog electronics from digital noise. The chip integrates the full-custom sensors matrix and the sparsifification/readout logic realized with standard-cells in STM CMOS technology 130 nm. For the chip characterization a test-beam has been set up on the 12 GeV PS (Proton Synchrotron) line facility at CERN of Geneva (CH). The collaboration prepared a silicon strip telescope and a DAQ system (hardware and software) for data acquisition and control of the telescope that allowed to store about 90 million events in 7 equivalent days of live-time of the beam. My activities concerned basically the realization of a firmware interface towards and from the MAPS chip in order to integrate it on the general DAQ system. Thereafter I worked on the DAQ software to implement on it a proper Slow Control interface of the APSEL4D. Several APSEL4D chips with different thinning have been tested during the test beam. Those with 100 and 300 um presented an overall efficiency of about 90% imparting a threshold of 450 electrons. The test-beam allowed to estimate also the resolution of the pixel sensor providing good results consistent with the pitch/sqrt(12) formula. The MAPS intrinsic resolution has been extracted from the width of the residual plot taking into account the multiple scattering effect.

Development and optimization of graphic user interfaces (GUIs) for infrared spectrometers at the Telescopio Nazionale Galileo

This Phd thesis was entirely developed at the Telescopio Nazionale Galileo (TNG, Roque de los Muchachos, La Palma Canary Islands) with the aim of designing, developing and implementing a new Graphical User Interface (GUI) for the Near Infrared Camera Spectrometer (NICS) installed on the Nasmyth A of the telescope. The idea of a new GUI for NICS has risen for optimizing the astronomers work through a set of powerful tools not present in the existing GUI, such as the possibility to move automatically, an object on the slit or do a very preliminary images analysis and spectra extraction. The new GUI also provides a wide and versatile image display, an automatic procedure to find out the astronomical objects and a facility for the automatic image crosstalk correction. In order to test the overall correct functioning of the new GUI for NICS, and providing some information on the atmospheric extinction at the TNG site, two telluric standard stars have been spectroscopically observed within some engineering time, namely Hip031303 and Hip031567. The used NICS set-up is as follows: Large Field (0.25'' /pixel) mode, 0.5'' slit and spectral dispersion through the AMICI prism (R~100), and the higher resolution (R~1000) JH and HK grisms.

Sistemi riconfigurabili a basso consumo per applicazioni di monitoraggio distribuito

The term Ambient Intelligence (AmI) refers to a vision on the future of the information society where smart, electronic environment are sensitive and responsive to the presence of people and their activities (Context awareness). In an ambient intelligence world, devices work in concert to support people in carrying out their everyday life activities, tasks and rituals in an easy, natural way using information and intelligence that is hidden in the network connecting these devices. This promotes the creation of pervasive environments improving the quality of life of the occupants and enhancing the human experience. AmI stems from the convergence of three key technologies: ubiquitous computing, ubiquitous communication and natural interfaces. Ambient intelligent systems are heterogeneous and require an excellent cooperation between several hardware/software technologies and disciplines, including signal processing, networking and protocols, embedded systems, information management, and distributed algorithms. Since a large amount of fixed and mobile sensors embedded is deployed into the environment, the Wireless Sensor Networks is one of the most relevant enabling technologies for AmI. WSN are complex systems made up of a number of sensor nodes which can be deployed in a target area to sense physical phenomena and communicate with other nodes and base stations. These simple devices typically embed a low power computational unit (microcontrollers, FPGAs etc.), a wireless communication unit, one or more sensors and a some form of energy supply (either batteries or energy scavenger modules). WNS promises of revolutionizing the interactions between the real physical worlds and human beings. Low-cost, low-computational power, low energy consumption and small size are characteristics that must be taken into consideration when designing and dealing with WSNs. To fully exploit the potential of distributed sensing approaches, a set of challengesmust be addressed. Sensor nodes are inherently resource-constrained systems with very low power consumption and small size requirements which enables than to reduce the interference on the physical phenomena sensed and to allow easy and low-cost deployment. They have limited processing speed,storage capacity and communication bandwidth that must be efficiently used to increase the degree of local ”understanding” of the observed phenomena. A particular case of sensor nodes are video sensors. This topic holds strong interest for a wide range of contexts such as military, security, robotics and most recently consumer applications. Vision sensors are extremely effective for medium to long-range sensing because vision provides rich information to human operators. However, image sensors generate a huge amount of data, whichmust be heavily processed before it is transmitted due to the scarce bandwidth capability of radio interfaces. In particular, in video-surveillance, it has been shown that source-side compression is mandatory due to limited bandwidth and delay constraints. Moreover, there is an ample opportunity for performing higher-level processing functions, such as object recognition that has the potential to drastically reduce the required bandwidth (e.g. by transmitting compressed images only when something ‘interesting‘ is detected). The energy cost of image processing must however be carefully minimized. Imaging could play and plays an important role in sensing devices for ambient intelligence. Computer vision can for instance be used for recognising persons and objects and recognising behaviour such as illness and rioting. Having a wireless camera as a camera mote opens the way for distributed scene analysis. More eyes see more than one and a camera system that can observe a scene from multiple directions would be able to overcome occlusion problems and could describe objects in their true 3D appearance. In real-time, these approaches are a recently opened field of research. In this thesis we pay attention to the realities of hardware/software technologies and the design needed to realize systems for distributed monitoring, attempting to propose solutions on open issues and filling the gap between AmI scenarios and hardware reality. The physical implementation of an individual wireless node is constrained by three important metrics which are outlined below. Despite that the design of the sensor network and its sensor nodes is strictly application dependent, a number of constraints should almost always be considered. Among them: • Small form factor to reduce nodes intrusiveness. • Low power consumption to reduce battery size and to extend nodes lifetime. • Low cost for a widespread diffusion. These limitations typically result in the adoption of low power, low cost devices such as low powermicrocontrollers with few kilobytes of RAMand tenth of kilobytes of program memory with whomonly simple data processing algorithms can be implemented. However the overall computational power of the WNS can be very large since the network presents a high degree of parallelism that can be exploited through the adoption of ad-hoc techniques. Furthermore through the fusion of information from the dense mesh of sensors even complex phenomena can be monitored. In this dissertation we present our results in building several AmI applications suitable for a WSN implementation. The work can be divided into two main areas:Low Power Video Sensor Node and Video Processing Alghoritm and Multimodal Surveillance . Low Power Video Sensor Nodes and Video Processing Alghoritms In comparison to scalar sensors, such as temperature, pressure, humidity, velocity, and acceleration sensors, vision sensors generate much higher bandwidth data due to the two-dimensional nature of their pixel array. We have tackled all the constraints listed above and have proposed solutions to overcome the current WSNlimits for Video sensor node. We have designed and developed wireless video sensor nodes focusing on the small size and the flexibility of reuse in different applications. The video nodes target a different design point: the portability (on-board power supply, wireless communication), a scanty power budget (500mW),while still providing a prominent level of intelligence, namely sophisticated classification algorithmand high level of reconfigurability. We developed two different video sensor node: The device architecture of the first one is based on a low-cost low-power FPGA+microcontroller system-on-chip. The second one is based on ARM9 processor. Both systems designed within the above mentioned power envelope could operate in a continuous fashion with Li-Polymer battery pack and solar panel. Novel low power low cost video sensor nodes which, in contrast to sensors that just watch the world, are capable of comprehending the perceived information in order to interpret it locally, are presented. Featuring such intelligence, these nodes would be able to cope with such tasks as recognition of unattended bags in airports, persons carrying potentially dangerous objects, etc.,which normally require a human operator. Vision algorithms for object detection, acquisition like human detection with Support Vector Machine (SVM) classification and abandoned/removed object detection are implemented, described and illustrated on real world data. Multimodal surveillance: In several setup the use of wired video cameras may not be possible. For this reason building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. Energy efficiency for wireless smart camera networks is one of the major efforts in distributed monitoring and surveillance community. For this reason, building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. The Pyroelectric Infra-Red (PIR) sensors have been used to extend the lifetime of a solar-powered video sensor node by providing an energy level dependent trigger to the video camera and the wireless module. Such approach has shown to be able to extend node lifetime and possibly result in continuous operation of the node.Being low-cost, passive (thus low-power) and presenting a limited form factor, PIR sensors are well suited for WSN applications. Moreover techniques to have aggressive power management policies are essential for achieving long-termoperating on standalone distributed cameras needed to improve the power consumption. We have used an adaptive controller like Model Predictive Control (MPC) to help the system to improve the performances outperforming naive power management policies.

An optimal estimator for the correlation of CMB anisotropies with Large Scale Structures and its application to WMAP-7year and NVSS

In the thesis we present the implementation of the quadratic maximum likelihood (QML) method, ideal to estimate the angular power spectrum of the cross-correlation between cosmic microwave background (CMB) and large scale structure (LSS) maps as well as their individual auto-spectra. Such a tool is an optimal method (unbiased and with minimum variance) in pixel space and goes beyond all the previous harmonic analysis present in the literature. We describe the implementation of the QML method in the {\it BolISW} code and demonstrate its accuracy on simulated maps throughout a Monte Carlo. We apply this optimal estimator to WMAP 7-year and NRAO VLA Sky Survey (NVSS) data and explore the robustness of the angular power spectrum estimates obtained by the QML method. Taking into account the shot noise and one of the systematics (declination correction) in NVSS, we can safely use most of the information contained in this survey. On the contrary we neglect the noise in temperature since WMAP is already cosmic variance dominated on the large scales. Because of a discrepancy in the galaxy auto spectrum between the estimates and the theoretical model, we use two different galaxy distributions: the first one with a constant bias $b$ and the second one with a redshift dependent bias $b(z)$. Finally, we make use of the angular power spectrum estimates obtained by the QML method to derive constraints on the dark energy critical density in a flat $\Lambda$CDM model by different likelihood prescriptions. When using just the cross-correlation between WMAP7 and NVSS maps with 1.8° resolution, we show that $\Omega_\Lambda$ is about the 70\% of the total energy density, disfavouring an Einstein-de Sitter Universe at more than 2 $\sigma$ CL (confidence level).

Automated Segmentation and Non-Rigid Registration for the Quantitative Evaluation of Myocardial Perfusion from Magnetic Resonance Images

Myocardial perfusion quantification by means of Contrast-Enhanced Cardiac Magnetic Resonance images relies on time consuming frame-by-frame manual tracing of regions of interest. In this Thesis, a novel automated technique for myocardial segmentation and non-rigid registration as a basis for perfusion quantification is presented. The proposed technique is based on three steps: reference frame selection, myocardial segmentation and non-rigid registration. In the first step, the reference frame in which both endo- and epicardial segmentation will be performed is chosen. Endocardial segmentation is achieved by means of a statistical region-based level-set technique followed by a curvature-based regularization motion. Epicardial segmentation is achieved by means of an edge-based level-set technique followed again by a regularization motion. To take into account the changes in position, size and shape of myocardium throughout the sequence due to out of plane respiratory motion, a non-rigid registration algorithm is required. The proposed non-rigid registration scheme consists in a novel multiscale extension of the normalized cross-correlation algorithm in combination with level-set methods. The myocardium is then divided into standard segments. Contrast enhancement curves are computed measuring the mean pixel intensity of each segment over time, and perfusion indices are extracted from each curve. The overall approach has been tested on synthetic and real datasets. For validation purposes, the sequences have been manually traced by an experienced interpreter, and contrast enhancement curves as well as perfusion indices have been computed. Comparisons between automatically extracted and manually obtained contours and enhancement curves showed high inter-technique agreement. Comparisons of perfusion indices computed using both approaches against quantitative coronary angiography and visual interpretation demonstrated that the two technique have similar diagnostic accuracy. In conclusion, the proposed technique allows fast, automated and accurate measurement of intra-myocardial contrast dynamics, and may thus address the strong clinical need for quantitative evaluation of myocardial perfusion.

Lesion detection and classification in breast cancer: evaluation of approaches based on morphological features, tracer kinetic modelling and semi-quantitative parameters in MR functional imaging (DCE-MRI)

The diagnosis, grading and classification of tumours has benefited considerably from the development of DCE-MRI which is now essential to the adequate clinical management of many tumour types due to its capability in detecting active angiogenesis. Several strategies have been proposed for DCE-MRI evaluation. Visual inspection of contrast agent concentration curves vs time is a very simple yet operator dependent procedure, therefore more objective approaches have been developed in order to facilitate comparison between studies. In so called model free approaches, descriptive or heuristic information extracted from time series raw data have been used for tissue classification. The main issue concerning these schemes is that they have not a direct interpretation in terms of physiological properties of the tissues. On the other hand, model based investigations typically involve compartmental tracer kinetic modelling and pixel-by-pixel estimation of kinetic parameters via non-linear regression applied on region of interests opportunely selected by the physician. This approach has the advantage to provide parameters directly related to the pathophysiological properties of the tissue such as vessel permeability, local regional blood flow, extraction fraction, concentration gradient between plasma and extravascular-extracellular space. Anyway, nonlinear modelling is computational demanding and the accuracy of the estimates can be affected by the signal-to-noise ratio and by the initial solutions. The principal aim of this thesis is investigate the use of semi-quantitative and quantitative parameters for segmentation and classification of breast lesion. The objectives can be subdivided as follow: describe the principal techniques to evaluate time intensity curve in DCE-MRI with focus on kinetic model proposed in literature; to evaluate the influence in parametrization choice for a classic bi-compartmental kinetic models; to evaluate the performance of a method for simultaneous tracer kinetic modelling and pixel classification; to evaluate performance of machine learning techniques training for segmentation and classification of breast lesion.

CT perfusion image processing: analysis of liver tumors

Perfusion CT imaging of the liver has potential to improve evaluation of tumour angiogenesis. Quantitative parameters can be obtained applying mathematical models to Time Attenuation Curve (TAC). However, there are still some difficulties for an accurate quantification of perfusion parameters due, for example, to algorithms employed, to mathematical model, to patient’s weight and cardiac output and to the acquisition system. In this thesis, new parameters and alternative methodologies about liver perfusion CT are presented in order to investigate the cause of variability of this technique. Firstly analysis were made to assess the variability related to the mathematical model used to compute arterial Blood Flow (BFa) values. Results were obtained implementing algorithms based on “ maximum slope method” and “Dual input one compartment model” . Statistical analysis on simulated data demonstrated that the two methods are not interchangeable. Anyway slope method is always applicable in clinical context. Then variability related to TAC processing in the application of slope method is analyzed. Results compared with manual selection allow to identify the best automatic algorithm to compute BFa. The consistency of a Standardized Perfusion Index (SPV) was evaluated and a simplified calibration procedure was proposed. At the end the quantitative value of perfusion map was analyzed. ROI approach and map approach provide related values of BFa and this means that pixel by pixel algorithm give reliable quantitative results. Also in pixel by pixel approach slope method give better results. In conclusion the development of new automatic algorithms for a consistent computation of BFa and the analysis and definition of simplified technique to compute SPV parameter, represent an improvement in the field of liver perfusion CT analysis.

Mappatura dell'impervious e consumo di suolo tramite analisi di change detection in telerilevamento

Il telerilevamento rappresenta un efficace strumento per il monitoraggio dell’ambiente e del territorio, grazie alla disponibilità di sensori che riprendono con cadenza temporale fissa porzioni della superficie terrestre. Le immagini multi/iperspettrali acquisite sono in grado di fornire informazioni per differenti campi di applicazione. In questo studio è stato affrontato il tema del consumo di suolo che rappresenta un’importante sfida per una corretta gestione del territorio, poiché direttamente connesso con i fenomeni del runoff urbano, della frammentazione ecosistemica e con la sottrazione di importanti territori agricoli. Ancora non esiste una definizione unica, ed anche una metodologia di misura, del consumo di suolo; in questo studio è stato definito come tale quello che provoca impermeabilizzazione del terreno. L’area scelta è quella della Provincia di Bologna che si estende per 3.702 km2 ed è caratterizzata a nord dalla Pianura Padana e a sud dalla catena appenninica; secondo i dati forniti dall’ISTAT, nel periodo 2001-2011 è stata la quarta provincia in Italia con più consumo di suolo. Tramite classificazione pixel-based è stata fatta una mappatura del fenomeno per cinque immagini Landsat. Anche se a media risoluzione, e quindi non in grado di mappare tutti i dettagli, esse sono particolarmente idonee per aree estese come quella scelta ed inoltre garantiscono una più ampia copertura temporale. Il periodo considerato va dal 1987 al 2013 e, tramite procedure di change detection applicate alle mappe prodotte, si è cercato di quantificare il fenomeno, confrontarlo con i dati esistenti e analizzare la sua distribuzione spaziale.