Problemi di diagnostica e restauro dei materiali decorativi nell'architettura Liberty in Emilia-Romagna

Le pietre artificiali ed i cementi artistici utilizzati durante la stagione Liberty rappresentano tutt’oggi un patrimonio artistico non ancora sufficientemente studiato. In seguito ad una ricerca bibliografica su testi e riviste dei primi anni del Novecento, è stata eseguita una ricognizione del patrimonio architettonico emiliano-romagnolo, al fine di valutarne i materiali e le tipologie di degrado più diffuse. Le città e le zone oggetto di studio sono state: Bologna, Ferrara, Modena e provincia, Reggio Emilia, Parma, Firenze, la Romagna e le Marche settentrionali. Tra gli edifici individuati sono state analizzate le decorazioni e gli intonaci di tre edifici ritenuti particolarmente significativi: il villino Pennazzi (noto anche come Villa Gina) a Borgo Panigale (Bologna), villa Verde a Bologna e l’ex-albergo Dorando Pietri a Carpi. Da tali edifici sono stati selezionati campioni rappresentativi delle diverse tipologie di decorazioni in pietra artificiale e successivamente sono stati caratterizzati in laboratorio tramite diffrattometria a raggi x (XRD), termogravimetria (TGA), microscopio ottico in sezioni lucide, microscopio elettronico a scansione (SEM) e porosimetria ad intrusione di mercurio (MIP). In particolare per Villa Verde sono state formulate e caratterizzate diverse tipologie di malte variando il tipo di legante ed il rapporto acqua/cemento, al fine di garantire la compatibilità fisico-meccanica con il supporto negli interventi di risarcimento delle lacune previsti nel restauro. L’attività sperimentale svolta ha permesso di mettere a punto un vero e proprio protocollo diagnostico per il restauro di questo tipo di decorazioni che potrà essere utilizzato sia nei casi di studio analizzati che per ogni futuro intervento.

Bone-implant interface. Evaluation of osteoblastic cells behavior on nanopatterned titanium surfaces: an in vitro analysis

Protein-adsorption occurs immediately following implantation of biomaterials. It is unknown at which extent protein-adsorption impacts the cellular events at bone-implant interface. To investigate this question, we compared the in-vitro outcome of osteoblastic cells grown onto titanium substrates and glass as control, by modulating the exposure to serum-derived proteins. Substrates consisted of 1) polished titanium disks; 2) polished disks nanotextured with H2SO4/H2O2; 3) glass. In the pre-adsorption phase, substrates were treated for 1h with αMEM alone (M-noFBS) or supplemented with 10%-foetal-bovine-serum (M-FBS). MC3T3-osteoblastic-cells were cultured on the pre-treated substrates for 3h and 24h, in M-noFBS and M-FBS. Subsequently, the culture medium was replaced with M-FBS and cultures maintained for 3 and 7days. Cell-number was evaluated by: Alamar-Blue and MTT assay. Mitotic- and osteogenic-activities were evaluated through fluorescence-optical-microscope by immunolabeling for Ki-67 nuclear-protein and Osteopontin. Cellular morphology was evaluated by SEM-imaging. Data were statistically analyzed using ANOVA-test, (p<0.05). At day3 and day7, the presence or absence of serum-derived proteins during the pre-adsorption phase had not significant effect on cell-number. Only the absence of FBS during 24h of culture significantly affected cell-number (p<0.0001). Titanium surfaces performed better than glass, (p<0.01). The growth rate of cells between day3 and 7 was not affected by the initial absence of FBS. Immunolabeling for Ki-67 and Osteopontin showed that the mitotic- and osteogenic- activity were ongoing at 72h. SEM-analysis revealed that the absence of FBS had no major influence on cell-shape. • Physico-chemical interactions without mediation by proteins are sufficient to sustain the initial phase of culture and guide osteogenic-cells toward differentiation. • The challenge is avoiding adsorption of ‘undesirables’ molecules that negatively impact on the cueing cells receive from surface. This may not be a problem in healthy patients, but may have an important role in medically-compromised-individuals in whom the composition of tissue-fluids is altered.

Optimizing fused deposition modelling: the impact of geometrical slicing parameters on mechanical properties

This comprehensive study explores the intricate world of 3D printing, with a focus on Fused Deposition Modelling (FDM). It sheds light on the critical factors that influence the quality and mechanical properties of 3D printed objects. Using an optical microscope with 40X magnification, the shapes of the printed beads is correlated to specific slicing parameters, resulting in a 2D parametric model. This mathematical model, derived from real samples, serves as a tool to predict general mechanical behaviour, bridging the gap between theory and practice in FDM printing. The study begins by emphasising the importance of geometric parameters such as layer height, line width and filament tolerance on the final printed bead geometry and the resulting theoretical effect on mechanical properties. The introduction of VPratio parameter (ratio between the area of the voids and the area occupied by printed material) allows the quantification of the variation of geometric slicing parameters on the improvement or reduction of mechanical properties. The study also addresses the effect of overhang and the role of filament diameter tolerances. The research continues with the introduction of 3D FEM (Finite Element Analysis) models based on the RVE (Representative Volume Element) to verify the results obtained from the 2D model and to analyse other aspects that affect mechanical properties and not directly observable with the 2D model. The study also proposes a model for the examination of 3D printed infill structures, introducing also an innovative methodology called “double RVE” which speeds up the calculation of mechanical properties and is also more computationally efficient. Finally, the limitations of the RVE model are shown and a so-called Hybrid RVE-based model is created to overcome the limitations and inaccuracy of the conventional RVE model and homogenization procedure on some printed geometries.