Reduced-order modelling, circuit-level design and SOI fabrication of microelectromechanical resonators

This thesis deals with two important research aspects concerning radio frequency (RF) microresonators and switches. First, a new approach for compact modeling and simulation of these devices is presented. Then, a combined process flow for their simultaneous fabrication on a SOI substrate is proposed. Compact models for microresonators and switches are extracted by applying mathematical model order reduction (MOR) to the devices finite element (FE) description in ANSYS c° . The behaviour of these devices includes forms of nonlinearities. However, an approximation in the creation of the FE model is introduced, which enables the use of linear model order reduction. Microresonators are modeled with the introduction of transducer elements, which allow for direct coupling of the electrical and mechanical domain. The coupled system element matrices are linearized around an operating point and reduced. The resulting macromodel is valid for small signal analysis around the bias point, such as harmonic pre-stressed analysis. This is extremely useful for characterizing the frequency response of resonators. Compact modelling of switches preserves the nonlinearity of the device behaviour. Nonlinear reduced order models are obtained by reducing the number of nonlinearities in the system and handling them as input to the system. In this way, the system can be reduced using linear MOR techniques and nonlinearities are introduced directly in the reduced order model. The reduction of the number of system nonlinearities implies the approximation of all distributed forces in the model with lumped forces. Both for microresonators and switches, a procedure for matrices extraction has been developed so that reduced order models include the effects of electrical and mechanical pre-stress. The extraction process is fast and can be done automatically from ANSYS binary files. The method has been applied for the simulation of several devices both at devices and circuit level. Simulation results have been compared with full model simulations, and, when available, experimental data. Reduced order models have proven to conserve the accuracy of finite element method and to give a good description of the overall device behaviour, despite the introduced approximations. In addition, simulation is very fast, both at device and circuit level. A combined process-flow for the integrated fabrication of microresonators and switches has been defined. For this purpose, two processes that are optimized for the independent fabrication of these devices are merged. The major advantage of this process is the possibility to create on-chip circuit blocks that include both microresonators and switches. An application is, for example, aswitched filter bank for wireless transceiver. The process for microresonators fabrication is characterized by the use of silicon on insulator (SOI) wafers and on a deep reactive ion etching (DRIE) step for the creation of the vibrating structures in single-crystal silicon and the use of a sacrificial oxide layer for the definition of resonator to electrode distance. The fabrication of switches is characterized by the use of two different conductive layers for the definition of the actuation electrodes and by the use of a photoresist as a sacrificial layer for the creation of the suspended structure. Both processes have a gold electroplating step, for the creation of the resonators electrodes, transmission lines and suspended structures. The combined process flow is designed such that it conserves the basic properties of the original processes. Neither the performance of the resonators nor the performance of the switches results affected by the simultaneous fabrication. Moreover, common fabrication steps are shared, which allows for cheaper and faster fabrication.

Development of musculoskeletal models for the design and the pre-clinical validation of hip resurfacing prosthesis

Background. The surgical treatment of dysfunctional hips is a severe condition for the patient and a costly therapy for the public health. Hip resurfacing techniques seem to hold the promise of various advantages over traditional THR, with particular attention to young and active patients. Although the lesson provided in the past by many branches of engineering is that success in designing competitive products can be achieved only by predicting the possible scenario of failure, to date the understanding of the implant quality is poorly pre-clinically addressed. Thus revision is the only delayed and reliable end point for assessment. The aim of the present work was to model the musculoskeletal system so as to develop a protocol for predicting failure of hip resurfacing prosthesis. Methods. Preliminary studies validated the technique for the generation of subject specific finite element (FE) models of long bones from Computed Thomography data. The proposed protocol consisted in the numerical analysis of the prosthesis biomechanics by deterministic and statistic studies so as to assess the risk of biomechanical failure on the different operative conditions the implant might face in a population of interest during various activities of daily living. Physiological conditions were defined including the variability of the anatomy, bone densitometry, surgery uncertainties and published boundary conditions at the hip. The protocol was tested by analysing a successful design on the market and a new prototype of a resurfacing prosthesis. Results. The intrinsic accuracy of models on bone stress predictions (RMSE < 10%) was aligned to the current state of the art in this field. The accuracy of prediction on the bone-prosthesis contact mechanics was also excellent (< 0.001 mm). The sensitivity of models prediction to uncertainties on modelling parameter was found below 8.4%. The analysis of the successful design resulted in a very good agreement with published retrospective studies. The geometry optimisation of the new prototype lead to a final design with a low risk of failure. The statistical analysis confirmed the minimal risk of the optimised design over the entire population of interest. The performances of the optimised design showed a significant improvement with respect to the first prototype (+35%). Limitations. On the authors opinion the major limitation of this study is on boundary conditions. The muscular forces and the hip joint reaction were derived from the few data available in the literature, which can be considered significant but hardly representative of the entire variability of boundary conditions the implant might face over the patients population. This moved the focus of the research on modelling the musculoskeletal system; the ongoing activity is to develop subject-specific musculoskeletal models of the lower limb from medical images. Conclusions. The developed protocol was able to accurately predict known clinical outcomes when applied to a well-established device and, to support the design optimisation phase providing important information on critical characteristics of the patients when applied to a new prosthesis. The presented approach does have a relevant generality that would allow the extension of the protocol to a large set of orthopaedic scenarios with minor changes. Hence, a failure mode analysis criterion can be considered a suitable tool in developing new orthopaedic devices.

Design and implementation of bioinformatics tools for large scale genome annotation

The continuous increase of genome sequencing projects produced a huge amount of data in the last 10 years: currently more than 600 prokaryotic and 80 eukaryotic genomes are fully sequenced and publically available. However the sole sequencing process of a genome is able to determine just raw nucleotide sequences. This is only the first step of the genome annotation process that will deal with the issue of assigning biological information to each sequence. The annotation process is done at each different level of the biological information processing mechanism, from DNA to protein, and cannot be accomplished only by in vitro analysis procedures resulting extremely expensive and time consuming when applied at a this large scale level. Thus, in silico methods need to be used to accomplish the task. The aim of this work was the implementation of predictive computational methods to allow a fast, reliable, and automated annotation of genomes and proteins starting from aminoacidic sequences. The first part of the work was focused on the implementation of a new machine learning based method for the prediction of the subcellular localization of soluble eukaryotic proteins. The method is called BaCelLo, and was developed in 2006. The main peculiarity of the method is to be independent from biases present in the training dataset, which causes the over‐prediction of the most represented examples in all the other available predictors developed so far. This important result was achieved by a modification, made by myself, to the standard Support Vector Machine (SVM) algorithm with the creation of the so called Balanced SVM. BaCelLo is able to predict the most important subcellular localizations in eukaryotic cells and three, kingdom‐specific, predictors were implemented. In two extensive comparisons, carried out in 2006 and 2008, BaCelLo reported to outperform all the currently available state‐of‐the‐art methods for this prediction task. BaCelLo was subsequently used to completely annotate 5 eukaryotic genomes, by integrating it in a pipeline of predictors developed at the Bologna Biocomputing group by Dr. Pier Luigi Martelli and Dr. Piero Fariselli. An online database, called eSLDB, was developed by integrating, for each aminoacidic sequence extracted from the genome, the predicted subcellular localization merged with experimental and similarity‐based annotations. In the second part of the work a new, machine learning based, method was implemented for the prediction of GPI‐anchored proteins. Basically the method is able to efficiently predict from the raw aminoacidic sequence both the presence of the GPI‐anchor (by means of an SVM), and the position in the sequence of the post‐translational modification event, the so called ω‐site (by means of an Hidden Markov Model (HMM)). The method is called GPIPE and reported to greatly enhance the prediction performances of GPI‐anchored proteins over all the previously developed methods. GPIPE was able to predict up to 88% of the experimentally annotated GPI‐anchored proteins by maintaining a rate of false positive prediction as low as 0.1%. GPIPE was used to completely annotate 81 eukaryotic genomes, and more than 15000 putative GPI‐anchored proteins were predicted, 561 of which are found in H. sapiens. In average 1% of a proteome is predicted as GPI‐anchored. A statistical analysis was performed onto the composition of the regions surrounding the ω‐site that allowed the definition of specific aminoacidic abundances in the different considered regions. Furthermore the hypothesis that compositional biases are present among the four major eukaryotic kingdoms, proposed in literature, was tested and rejected. All the developed predictors and databases are freely available at: BaCelLo http://gpcr.biocomp.unibo.it/bacello eSLDB http://gpcr.biocomp.unibo.it/esldb GPIPE http://gpcr.biocomp.unibo.it/gpipe

Design of wireless sensor networks for fluid dynamic applications

In fluid dynamics research, pressure measurements are of great importance to define the flow field acting on aerodynamic surfaces. In fact the experimental approach is fundamental to avoid the complexity of the mathematical models for predicting the fluid phenomena. It’s important to note that, using in-situ sensor to monitor pressure on large domains with highly unsteady flows, several problems are encountered working with the classical techniques due to the transducer cost, the intrusiveness, the time response and the operating range. An interesting approach for satisfying the previously reported sensor requirements is to implement a sensor network capable of acquiring pressure data on aerodynamic surface using a wireless communication system able to collect the pressure data with the lowest environmental–invasion level possible. In this thesis a wireless sensor network for fluid fields pressure has been designed, built and tested. To develop the system, a capacitive pressure sensor, based on polymeric membrane, and read out circuitry, based on microcontroller, have been designed, built and tested. The wireless communication has been performed using the Zensys Z-WAVE platform, and network and data management have been implemented. Finally, the full embedded system with antenna has been created. As a proof of concept, the monitoring of pressure on the top of the mainsail in a sailboat has been chosen as working example.

Design and Performance Evaluation of Network-on-Chip Communication Protocols and Architectures

The scale down of transistor technology allows microelectronics manufacturers such as Intel and IBM to build always more sophisticated systems on a single microchip. The classical interconnection solutions based on shared buses or direct connections between the modules of the chip are becoming obsolete as they struggle to sustain the increasing tight bandwidth and latency constraints that these systems demand. The most promising solution for the future chip interconnects are the Networks on Chip (NoC). NoCs are network composed by routers and channels used to inter- connect the different components installed on the single microchip. Examples of advanced processors based on NoC interconnects are the IBM Cell processor, composed by eight CPUs that is installed on the Sony Playstation III and the Intel Teraflops pro ject composed by 80 independent (simple) microprocessors. On chip integration is becoming popular not only in the Chip Multi Processor (CMP) research area but also in the wider and more heterogeneous world of Systems on Chip (SoC). SoC comprehend all the electronic devices that surround us such as cell-phones, smart-phones, house embedded systems, automotive systems, set-top boxes etc... SoC manufacturers such as ST Microelectronics , Samsung, Philips and also Universities such as Bologna University, M.I.T., Berkeley and more are all proposing proprietary frameworks based on NoC interconnects. These frameworks help engineers in the switch of design methodology and speed up the development of new NoC-based systems on chip. In this Thesis we propose an introduction of CMP and SoC interconnection networks. Then focusing on SoC systems we propose: • a detailed analysis based on simulation of the Spidergon NoC, a ST Microelectronics solution for SoC interconnects. The Spidergon NoC differs from many classical solutions inherited from the parallel computing world. Here we propose a detailed analysis of this NoC topology and routing algorithms. Furthermore we propose aEqualized a new routing algorithm designed to optimize the use of the resources of the network while also increasing its performance; • a methodology flow based on modified publicly available tools that combined can be used to design, model and analyze any kind of System on Chip; • a detailed analysis of a ST Microelectronics-proprietary transport-level protocol that the author of this Thesis helped developing; • a simulation-based comprehensive comparison of different network interface designs proposed by the author and the researchers at AST lab, in order to integrate shared-memory and message-passing based components on a single System on Chip; • a powerful and flexible solution to address the time closure exception issue in the design of synchronous Networks on Chip. Our solution is based on relay stations repeaters and allows to reduce the power and area demands of NoC interconnects while also reducing its buffer needs; • a solution to simplify the design of the NoC by also increasing their performance and reducing their power and area consumption. We propose to replace complex and slow virtual channel-based routers with multiple and flexible small Multi Plane ones. This solution allows us to reduce the area and power dissipation of any NoC while also increasing its performance especially when the resources are reduced. This Thesis has been written in collaboration with the Advanced System Technology laboratory in Grenoble France, and the Computer Science Department at Columbia University in the city of New York.

Design of optical networks for advanced applications

Nowadays, computing is migrating from traditional high performance and distributed computing to pervasive and utility computing based on heterogeneous networks and clients. The current trend suggests that future IT services will rely on distributed resources and on fast communication of heterogeneous contents. The success of this new range of services is directly linked to the effectiveness of the infrastructure in delivering them. The communication infrastructure will be the aggregation of different technologies even though the current trend suggests the emergence of single IP based transport service. Optical networking is a key technology to answer the increasing requests for dynamic bandwidth allocation and configure multiple topologies over the same physical layer infrastructure, optical networks today are still “far” from accessible from directly configure and offer network services and need to be enriched with more “user oriented” functionalities. However, current Control Plane architectures only facilitate efficient end-to-end connectivity provisioning and certainly cannot meet future network service requirements, e.g. the coordinated control of resources. The overall objective of this work is to provide the network with the improved usability and accessibility of the services provided by the Optical Network. More precisely, the definition of a service-oriented architecture is the enable technology to allow user applications to gain benefit of advanced services over an underlying dynamic optical layer. The definition of a service oriented networking architecture based on advanced optical network technologies facilitates users and applications access to abstracted levels of information regarding offered advanced network services. This thesis faces the problem to define a Service Oriented Architecture and its relevant building blocks, protocols and languages. In particular, this work has been focused on the use of the SIP protocol as a inter-layers signalling protocol which defines the Session Plane in conjunction with the Network Resource Description language. On the other hand, an advantage optical network must accommodate high data bandwidth with different granularities. Currently, two main technologies are emerging promoting the development of the future optical transport network, Optical Burst and Packet Switching. Both technologies respectively promise to provide all optical burst or packet switching instead of the current circuit switching. However, the electronic domain is still present in the scheduler forwarding and routing decision. Because of the high optics transmission frequency the burst or packet scheduler faces a difficult challenge, consequentially, high performance and time focused design of both memory and forwarding logic is need. This open issue has been faced in this thesis proposing an high efficiently implementation of burst and packet scheduler. The main novelty of the proposed implementation is that the scheduling problem has turned into simple calculation of a min/max function and the function complexity is almost independent of on the traffic conditions.

Rafael Moneo: la complessità del vuoto. Dalle matrici formali dell'opera di Oteiza e Chillida

The experience of void, essential to the production of forms and to make use them, can be considered as the base of the activities that attend to the formative processes. If void and matter constitutes the basic substances of architecture. Their role in the definition of form, the symbolic value and the constructive methods of it defines the quality of the space. This job inquires the character of space in the architecture of Moneo interpreting the meaning of the void in the Basque culture through the reading of the form matrices in the work of Jorge Oteiza and Eduardo Chillida. In the tie with the Basque culture a reading key is characterized by concurring to put in relation some of the theoretical principles expressed by Moneo on the relationship between place and time, in an unique and specific vision of the space. In the analysis of the process that determines the genesis of the architecture of Moneo emerges a trajectory whose direction is constructed on two pivos: on the one hand architecture like instrument of appropriation of the place, gushed from an acquaintance process who leans itself to the reading of the relations that define the place and of the resonances through which measuring it, on the other hand the architecture whose character is able to represent and to extend the time in which he is conceived, through the autonomy that is conferred to them from values. Following the trace characterized from this hypothesis, that is supported on the theories elaborated from Moneo, surveying deepens the reading of the principles that construct the sculptural work of Oteiza and Chillida, features from a search around the topic of the void and to its expression through the form. It is instrumental to the definition of a specific area that concurs to interpret the character of the space subtended to a vision of the place and the time, affine to the sensibility of Moneo and in some way not stranger to its cultural formation. The years of the academic formation, during which Moneo enters in contact with the Basque artistic culture, seem to be an important period in the birth of that knowledge that will leads him to the formulation of theories tied to the relationship between time, place and architecture. The values expressed through the experimental work of Oteiza and Chillida during years '50 are valid bases to the understanding of such relationships. In tracing a profile of the figures of Oteiza and Chillida, without the pretension that it is exhaustive for the reading of the complex historical period in which they are placed, but with the needs to put the work in a context, I want to be evidenced the important role carried out from the two artists from the Basque cultural area within which Moneo moves its first steps. The tie that approaches Moneo to the Basque culture following the personal trajectory of the formative experience interlaces to that one of important figures of the art and the Spanish architecture. One of the more meaningful relationships is born just during the years of his academic formation, from 1958 to the 1961, when he works like student in the professional office of the architect Francisco Sáenz de Oiza, who was teaching architectural design at the ETSAM. In these years many figures of Basque artists alternated at the professional office of Oiza that enjoys the important support of the manufacturer and maecenas Juan Huarte Beaumont, introduced to he from Oteiza. The tie between Huarte and Oteiza is solid and continuous in the years and it realizes in a contribution to many of the initiatives that makes of Oteiza a forwarder of the Basque culture. In the four years of collaboration with Oiza, Moneo has the opportunity to keep in contact with an atmosphere permeated by a constant search in the field of the plastic art and with figures directly connected to such atmosphere. It’s of a period of great intensity as in the production like in the promotion of the Basque art. The collective “Blanco y Negro”, than is held in 1959 at the Galería Darro to Madrid, is only one of the many times of an exhibition of the work of Oteiza and Chillida. The end of the Fifties is a period of international acknowledgment for Chillida that for Oteiza. The decade of the Fifties consecrates the hypotheses of a mythical past of the Basque people through the spread of the studies carried out in the antecedent years. The archaeological discoveries that join to a context already rich of signs of the prehistoric era, consolidate the knowledge of a strong cultural identity. Oteiza, like Chillida and other contemporary artists, believe in a cosmogonist conception belonging to the Basques, connected to their matriarchal mythological past. The void in its meaning of absence, in the Basque culture, thus as in various archaic and oriental religions, is equivalent to the spiritual fullness as essential condition to the revealing of essence. Retracing the archaic origins of the Basque culture emerges the deep meaning that the void assumes as key element in the religious interpretation of the passage from the life to the death. The symbology becomes rich of meaningful characters who derive from the fact that it is a chthonic cult. A representation of earth like place in which divine manifest itself but also like connection between divine and human, and this manipulation of the matter of which the earth it is composed is the tangible projection of the continuous search of the man towards God. The search of equilibrium between empty and full, that characterizes also the development of the form in architecture, in the Basque culture assumes therefore a peculiar value that returns like constant in great part of the plastic expressions, than in this context seem to be privileged regarding the other expressive forms. Oteiza and Chillida develop two original points of view in the representation of the void through the form. Both use of rigorous systems of rules sensitive to the physics principles and the characters of the matter. The last aim of the Oteiza’s construction is the void like limit of the knowledge, like border between known and unknown. It doesn’t means to reduce the sculptural object to an only allusive dimension because the void as physical and spiritual power is an active void, that possesses that value able to reveal the being through the trace of un-being. The void in its transcendental manifestation acts at the same time from universal and from particular, like in the atomic structure of the matter, in which on one side it constitutes the inner structure of every atom and on the other one it is necessary condition to the interaction between all the atoms. The void can be seen therefore as the action field that concurs the relations between the forms but is also the necessary condition to the same existence of the form. In the construction of Chillida the void represents that counterpart structuring the matter, inborn in it, the element in absence of which wouldn’t be variations neither distinctive characters to define the phenomenal variety of the world. The physics laws become the subject of the sculptural representation, the void are the instrument that concurs to catch up the equilibrium. Chillida dedicate himself to experience the space through the senses, to perceive of the qualities, to tell the physics laws which forge the matter in the form and the form arranges the places. From the artistic experience of the two sculptors they can be transposed, to the architectonic work of Moneo, those matrices on which they have constructed their original lyric expressions, where the void is absolute protagonist. An ambit is defined thus within which the matrices form them drafts from the work of Oteiza and Chillida can be traced in the definition of the process of birth and construction of the architecture of Moneo, but also in the relation that the architecture establishes with the place and in the time. The void becomes instrument to read the space constructed in its relationships that determine the proportions, rhythms, and relations. In this way the void concurs to interpret the architectonic space and to read the value of it, the quality of the spaces constructing it. This because it’s like an instrument of the composition, whose role is to maintain to the separation between the elements putting in evidence the field of relations. The void is that instrument that serves to characterize the elements that are with in the composition, related between each other, but distinguished. The meaning of the void therefore pushes the interpretation of the architectonic composition on the game of the relations between the elements that, independent and distinguished, strengthen themselves in their identity. On the one hand if void, as measurable reality, concurs all the dimensional changes quantifying the relationships between the parts, on the other hand its dialectic connotation concurs to search the equilibrium that regulated such variations. Equilibrium that therefore does not represent an obtained state applying criteria setting up from arbitrary rules but that depends from the intimate nature of the matter and its embodiment in the form. The production of a form, or a formal system that can be finalized to the construction of a building, is indissolubly tied to the technique that is based on the acquaintance of the formal vocation of the matter, and what it also can representing, meaning, expresses itself in characterizing the site. For Moneo, in fact, the space defined from the architecture is above all a site, because the essence of the site is based on the construction. When Moneo speaks about “birth of the idea of plan” like essential moment in the construction process of the architecture, it refers to a process whose complexity cannot be born other than from a deepened acquaintance of the site that leads to the comprehension of its specificity. Specificity arise from the infinite sum of relations, than for Moneo is the story of the oneness of a site, of its history, of the cultural identity and of the dimensional characters that that they are tied to it beyond that to the physical characteristics of the site. This vision is leaned to a solid made physical structure of perceptions, of distances, guideline and references that then make that the process is first of all acquaintance, appropriation. Appropriation that however does not happen for directed consequence because does not exist a relationship of cause and effect between place and architecture, thus as an univocal and exclusive way does not exist to arrive to a representation of an idea. An approach that, through the construction of the place where the architecture acquires its being, searches an expression of its sense of the truth. The proposal of a distinction for areas like space, matter, spirit and time, answering to the issues that scan the topics of the planning search of Moneo, concurs a more immediate reading of the systems subtended to the composition principles, through which is related the recurrent architectonic elements in its planning dictionary. From the dialectic between the opposites that is expressed in the duality of the form, through the definition of a complex element that can mediate between inside and outside as a real system of exchange, Moneo experiences the form development of the building deepening the relations that the volume establishes in the site. From time to time the invention of a system used to answer to the needs of the program and to resolve the dual character of the construction in an only gesture, involves a deep acquaintance of the professional practice. The technical aspect is the essential support to which the construction of the system is indissolubly tied. What therefore arouses interest is the search of the criteria and the way to construct that can reveal essential aspects of the being of the things. The constructive process demands, in fact, the acquaintance of the formative properties of the matter. Property from which the reflections gush on the relations that can be born around the architecture through the resonance produced from the forms. The void, in fact, through the form is in a position to constructing the site establishing a reciprocity relation. A reciprocity that is determined in the game between empty and full and of the forms between each other, regarding around, but also with regard to the subjective experience. The construction of a background used to amplify what is arranged on it and to clearly show the relations between the parts and at the same time able to tie itself with around opening the space of the vision, is a system that in the architecture of Moneo has one of its more effective applications in the use of the platform used like architectonic element. The spiritual force of this architectonic gesture is in the ability to define a place whose projecting intention is perceived and shared with who experience and has lived like some instrument to contact the cosmic forces, in a delicate process that lead to the equilibrium with them, but in completely physical way. The principles subtended to the construction of the form taken from the study of the void and the relations that it concurs, lead to express human values in the construction of the site. The validity of these principles however is tested from the time. The time is what Moneo considers as filter that every architecture is subordinate to and the survival of architecture, or any of its formal characters, reveals them the validity of the principles that have determined it. It manifests thus, in the tie between the spatial and spiritual dimension, between the material and the worldly dimension, the state of necessity that leads, in the construction of the architecture, to establish a contact with the forces of the universe and the intimate world, through a process that translate that necessity in elaboration of a formal system.

Middleware principles and design for the integration of ubiquitos mobile services

Nowadays, in Ubiquitous computing scenarios users more and more require to exploit online contents and services by means of any device at hand, no matter their physical location, and by personalizing and tailoring content and service access to their own requirements. The coordinated provisioning of content tailored to user context and preferences, and the support for mobile multimodal and multichannel interactions are of paramount importance in providing users with a truly effective Ubiquitous support. However, so far the intrinsic heterogeneity and the lack of an integrated approach led to several either too vertical, or practically unusable proposals, thus resulting in poor and non-versatile support platforms for Ubiquitous computing. This work investigates and promotes design principles to help cope with these ever-changing and inherently dynamic scenarios. By following the outlined principles, we have designed and implemented a middleware support platform to support the provisioning of Ubiquitous mobile services and contents. To prove the viability of our approach, we have realized and stressed on top of our support platform a number of different, extremely complex and heterogeneous content and service provisioning scenarios. The encouraging results obtained are pushing our research work further, in order to provide a dynamic platform that is able to not only dynamically support novel Ubiquitous applicative scenarios by tailoring extremely diverse services and contents to heterogeneous user needs, but is also able to reconfigure and adapt itself in order to provide a truly optimized and tailored support for Ubiquitous service provisioning.

Body ares networks for human motor assessment

Healthcare, Human Computer Interfaces (HCI), Security and Biometry are the most promising application scenario directly involved in the Body Area Networks (BANs) evolution. Both wearable devices and sensors directly integrated in garments envision a word in which each of us is supervised by an invisible assistant monitoring our health and daily-life activities. New opportunities are enabled because improvements in sensors miniaturization and transmission efficiency of the wireless protocols, that achieved the integration of high computational power aboard independent, energy-autonomous, small form factor devices. Application’s purposes are various: (I) data collection to achieve off-line knowledge discovery; (II) user notification of his/her activities or in case a danger occurs; (III) biofeedback rehabilitation; (IV) remote alarm activation in case the subject need assistance; (V) introduction of a more natural interaction with the surrounding computerized environment; (VI) users identification by physiological or behavioral characteristics. Telemedicine and mHealth [1] are two of the leading concepts directly related to healthcare. The capability to borne unobtrusiveness objects supports users’ autonomy. A new sense of freedom is shown to the user, not only supported by a psychological help but a real safety improvement. Furthermore, medical community aims the introduction of new devices to innovate patient treatments. In particular, the extension of the ambulatory analysis in the real life scenario by proving continuous acquisition. The wide diffusion of emerging wellness portable equipment extended the usability of wearable devices also for fitness and training by monitoring user performance on the working task. The learning of the right execution techniques related to work, sport, music can be supported by an electronic trainer furnishing the adequate aid. HCIs made real the concept of Ubiquitous, Pervasive Computing and Calm Technology introduced in the 1988 by Marc Weiser and John Seeley Brown. They promotes the creation of pervasive environments, enhancing the human experience. Context aware, adaptive and proactive environments serve and help people by becoming sensitive and reactive to their presence, since electronics is ubiquitous and deployed everywhere. In this thesis we pay attention to the integration of all the aspects involved in a BAN development. Starting from the choice of sensors we design the node, configure the radio network, implement real-time data analysis and provide a feedback to the user. We present algorithms to be implemented in wearable assistant for posture and gait analysis and to provide assistance on different walking conditions, preventing falls. Our aim, expressed by the idea to contribute at the development of a non proprietary solutions, driven us to integrate commercial and standard solutions in our devices. We use sensors available on the market and avoided to design specialized sensors in ASIC technologies. We employ standard radio protocol and open source projects when it was achieved. The specific contributions of the PhD research activities are presented and discussed in the following. • We have designed and build several wireless sensor node providing both sensing and actuator capability making the focus on the flexibility, small form factor and low power consumption. The key idea was to develop a simple and general purpose architecture for rapid analysis, prototyping and deployment of BAN solutions. Two different sensing units are integrated: kinematic (3D accelerometer and 3D gyroscopes) and kinetic (foot-floor contact pressure forces). Two kind of feedbacks were implemented: audio and vibrotactile. • Since the system built is a suitable platform for testing and measuring the features and the constraints of a sensor network (radio communication, network protocols, power consumption and autonomy), we made a comparison between Bluetooth and ZigBee performance in terms of throughput and energy efficiency. Test in the field evaluate the usability in the fall detection scenario. • To prove the flexibility of the architecture designed, we have implemented a wearable system for human posture rehabilitation. The application was developed in conjunction with biomedical engineers who provided the audio-algorithms to furnish a biofeedback to the user about his/her stability. • We explored off-line gait analysis of collected data, developing an algorithm to detect foot inclination in the sagittal plane, during walk. • In collaboration with the Wearable Lab – ETH, Zurich, we developed an algorithm to monitor the user during several walking condition where the user carry a load. The remainder of the thesis is organized as follows. Chapter I gives an overview about Body Area Networks (BANs), illustrating the relevant features of this technology and the key challenges still open. It concludes with a short list of the real solutions and prototypes proposed by academic research and manufacturers. The domain of the posture and gait analysis, the methodologies, and the technologies used to provide real-time feedback on detected events, are illustrated in Chapter II. The Chapter III and IV, respectively, shown BANs developed with the purpose to detect fall and monitor the gait taking advantage by two inertial measurement unit and baropodometric insoles. Chapter V reports an audio-biofeedback system to improve balance on the information provided by the use centre of mass. A walking assistant based on the KNN classifier to detect walking alteration on load carriage, is described in Chapter VI.

Modelli Digitali e Archivi di Progetto. Sistemi integrati di documentazione per l'architettura.

Le tecniche dell'informazione e i metodi della comunicazione hanno modificato il modo di redigere documenti destinati a trasmettere la conoscenza, in un processo che è a tutt'oggi in corso di evoluzione. Anche l'attività progettuale in ingegneria ed architettura, pure in un settore caratterizzato da una notevole inerzia metodologica e restio all'innovazione quale è quello dell'industria edilizia, ha conosciuto profonde trasformazioni in ragione delle nuove espressioni tecnologiche. Da tempo l'informazione necessaria per realizzare un edificio, dai disegni che lo rappresentano sino ai documenti che ne indicano le modalità costruttive, può essere gestita in maniera centralizzata mediante un unico archivio di progetto denominato IPDB (Integrated Project DataBase) pur essendone stata recentemente introdotta sul mercato una variante più operativa chiamata BIM (Building Information Modelling). Tuttavia l'industrializzazione del progetto che questi strumenti esplicano non rende conto appieno di tutti gli aspetti che vedono la realizzazione dell'opera architettonica come collettore di conoscenze proprie di una cultura progettuale che, particolarmente in Italia, è radicata nel tempo. La semantica della rappresentazione digitale è volta alla perequazione degli elementi costitutivi del progetto con l'obiettivo di catalogarne le sole caratteristiche fabbricative. L'analisi della letteratura scientifica pertinente alla materia mostra come non sia possibile attribuire ai metodi ed ai software presenti sul mercato la valenza di raccoglitori omnicomprensivi di informazione: questo approccio olistico costituisce invece il fondamento della modellazione integrata intesa come originale processo di rappresentazione della conoscenza, ordinata secondo il paradigma delle "scatole cinesi", modello evolvente che unifica linguaggi appartenenti ai differenti attori compartecipanti nei settori impiantistici, strutturali e della visualizzazione avanzata. Evidenziando criticamente i pregi e i limiti operativi derivanti dalla modellazione integrata, la componente sperimentale della ricerca è stata articolata con l'approfondimento di esperienze condotte in contesti accademici e professionali. Il risultato conseguito ha coniugato le tecniche di rilevamento alle potenzialità di "modelli tridimensionali intelligenti", dotati cioè di criteri discriminanti per la valutazione del relazionamento topologico dei componenti con l'insieme globale.

Performance evaluation of low environmental impact asphalt concretes using the mechanistic empirical design method based on laboratory fatigue and permanent deformation models

The "sustainability" concept relates to the prolonging of human economic systems with as little detrimental impact on ecological systems as possible. Construction that exhibits good environmental stewardship and practices that conserve resources in a manner that allow growth and development to be sustained for the long-term without degrading the environment are indispensable in a developed society. Past, current and future advancements in asphalt as an environmentally sustainable paving material are especially important because the quantities of asphalt used annually in Europe as well as in the U.S. are large. The asphalt industry is still developing technological improvements that will reduce the environmental impact without affecting the final mechanical performance. Warm mix asphalt (WMA) is a type of asphalt mix requiring lower production temperatures compared to hot mix asphalt (HMA), while aiming to maintain the desired post construction properties of traditional HMA. Lowering the production temperature reduce the fuel usage and the production of emissions therefore and that improve conditions for workers and supports the sustainable development. Even the crumb-rubber modifier (CRM), with shredded automobile tires and used in the United States since the mid 1980s, has proven to be an environmentally friendly alternative to conventional asphalt pavement. Furthermore, the use of waste tires is not only relevant in an environmental aspect but also for the engineering properties of asphalt [Pennisi E., 1992]. This research project is aimed to demonstrate the dual value of these Asphalt Mixes in regards to the environmental and mechanical performance and to suggest a low environmental impact design procedure. In fact, the use of eco-friendly materials is the first phase towards an eco-compatible design but it cannot be the only step. The eco-compatible approach should be extended also to the design method and material characterization because only with these phases is it possible to exploit the maximum potential properties of the used materials. Appropriate asphalt concrete characterization is essential and vital for realistic performance prediction of asphalt concrete pavements. Volumetric (Mix design) and mechanical (Permanent deformation and Fatigue performance) properties are important factors to consider. Moreover, an advanced and efficient design method is necessary in order to correctly use the material. A design method such as a Mechanistic-Empirical approach, consisting of a structural model capable of predicting the state of stresses and strains within the pavement structure under the different traffic and environmental conditions, was the application of choice. In particular this study focus on the CalME and its Incremental-Recursive (I-R) procedure, based on damage models for fatigue and permanent shear strain related to the surface cracking and to the rutting respectively. It works in increments of time and, using the output from one increment, recursively, as input to the next increment, predicts the pavement conditions in terms of layer moduli, fatigue cracking, rutting and roughness. This software procedure was adopted in order to verify the mechanical properties of the study mixes and the reciprocal relationship between surface layer and pavement structure in terms of fatigue and permanent deformation with defined traffic and environmental conditions. The asphalt mixes studied were used in a pavement structure as surface layer of 60 mm thickness. The performance of the pavement was compared to the performance of the same pavement structure where different kinds of asphalt concrete were used as surface layer. In comparison to a conventional asphalt concrete, three eco-friendly materials, two warm mix asphalt and a rubberized asphalt concrete, were analyzed. The First Two Chapters summarize the necessary steps aimed to satisfy the sustainable pavement design procedure. In Chapter I the problem of asphalt pavement eco-compatible design was introduced. The low environmental impact materials such as the Warm Mix Asphalt and the Rubberized Asphalt Concrete were described in detail. In addition the value of a rational asphalt pavement design method was discussed. Chapter II underlines the importance of a deep laboratory characterization based on appropriate materials selection and performance evaluation. In Chapter III, CalME is introduced trough a specific explanation of the different equipped design approaches and specifically explaining the I-R procedure. In Chapter IV, the experimental program is presented with a explanation of test laboratory devices adopted. The Fatigue and Rutting performances of the study mixes are shown respectively in Chapter V and VI. Through these laboratory test data the CalME I-R models parameters for Master Curve, fatigue damage and permanent shear strain were evaluated. Lastly, in Chapter VII, the results of the asphalt pavement structures simulations with different surface layers were reported. For each pavement structure, the total surface cracking, the total rutting, the fatigue damage and the rutting depth in each bound layer were analyzed.

Sviluppo di sperimentazioni per la produzione di getti in lega di alluminio a caratteristiche difettologiche e microstrutturali controllate, per la validazione di modelli di previsione delle porosità

Nei processi di progettazione e produzione tramite tecnologie di colata di componenti in alluminio ad elevate prestazioni, risulta fondamentale poter prevedere la presenza e la quantità di difetti correlabili a design non corretti e a determinate condizioni di processo. Fra le difettologie più comuni di un getto in alluminio, le porosità con dimensioni di decine o centinaia di m, note come microporosità, hanno un impatto estremamente negativo sulle caratteristiche meccaniche, sia statiche che a fatica. In questo lavoro, dopo un’adeguata analisi bibliografica, sono state progettate e messe a punto attrezzature e procedure sperimentali che permettessero la produzione di materiale a difettologia e microstruttura differenziata, a partire da condizioni di processo note ed accuratamente misurabili, che riproducessero la variabilità delle stesse nell’ambito della reale produzione di componenti fusi. Tutte le attività di progettazione delle sperimentazioni, sono state coadiuvate dall’ausilio di software di simulazione del processo fusorio che hanno a loro volta beneficiato di tarature e validazioni sperimentali ad hoc. L’apparato sperimentale ha dimostrato la propria efficacia nella produzione di materiale a microstruttura e difettologia differenziata, in maniera robusta e ripetibile. Utilizzando i risultati sperimentali ottenuti, si è svolta la validazione di un modello numerico di previsione delle porosità da ritiro e gas, ritenuto ad oggi allo stato dell’arte e già implementato in alcuni codici commerciali di simulazione del processo fusorio. I risultati numerici e sperimentali, una volta comparati, hanno evidenziato una buona accuratezza del modello numerico nella previsione delle difettologie sia in termini di ordini di grandezza che di gradienti della porosità nei getti realizzati.

Valutazione della risposta sismica di edifici mediante modelli anelastici equivalenti

Nella presente tesi è proposta una metodologia per lo studio e la valutazione del comportamento sismico di edifici a telaio. Il metodo prevede la realizzazione di analisi non-lineari su modelli equivalenti MDOF tipo stick, in accordo alla classificazione data nel report FEMA 440. Gli step per l’applicazione del metodo sono descritti nella tesi. Per la validazione della metodologia si sono utilizzati confronti con analisi time-history condotte su modelli tridimensionali dettagliati delle strutture studiate (detailed model). I parametri ingegneristici considerati nel confronto, nell’ottica di utilizzare il metodo proposto in un approccio del tipo Displacement-Based Design sono lo spostamento globale in sommità, gli spostamenti di interpiano, le forze di piano e la forza totale alla base. I risultati delle analisi condotte sui modelli stick equivalenti, mostrano una buona corrispondenza, ottima in certi casi, con quelli delle analisi condotte sui modelli tridimensionali dettagliati. Le time-history realizzate sugli stick model permettono però, un consistente risparmio in termini di onere computazionale e di tempo per il post-processing dei risultati ottenuti.

Synthesis of Biologically Active Small Molecules: Different Approaches to Drug Design

In the past years, genome biology had disclosed an ever-growing kind of biological targets that emerged as ideal points for therapeutic intervention. Nevertheless, the number of new chemical entities (NCEs) translated into effective therapies employed in the clinic, still not observed. Innovative strategies in drug discovery combined with different approaches to drug design should be searched for bridge this gap. In this context organic synthetic chemistry had to provide for effective strategies to achieve biologically active small molecules to consider not only as potentially drug candidates, but also as chemical tools to dissect biological systems. In this scenario, during my PhD, inspired by the Biology-oriented Synthesis approach, a small library of hybrid molecules endowed with privileged scaffolds, able to block cell cycle and to induce apoptosis and cell differentiation, merged with natural-like cores were synthesized. A synthetic platform which joined a Domino Knoevenagel-Diels Alder reaction with a Suzuki coupling was performed in order to reach the hybrid compounds. These molecules can represent either antitumor lead candidates, or valuable chemical tools to study molecular pathways in cancer cells. The biological profile expressed by some of these derivatives showed a well defined antiproliferative activity on leukemia Bcr-Abl expressing K562 cell lines. A parallel project regarded the rational design and synthesis of minimally structurally hERG blockers with the purpose of enhancing the SAR studies of a previously synthesized collection. A Target-Oriented Synthesis approach was applied. Combining conventional and microwave heating, the desired final compounds were achieved in good yields and reaction rates. The preliminary biological results of the compounds, showed a potent blocking activity. The obtained small set of hERG blockers, was able to gain more insight the minimal structural requirements for hERG liability, which is mandatory to investigate in order to reduce the risk of potential side effects of new drug candidates.

Decomposition Methods and Network Design Problems

Decomposition based approaches are recalled from primal and dual point of view. The possibility of building partially disaggregated reduced master problems is investigated. This extends the idea of aggregated-versus-disaggregated formulation to a gradual choice of alternative level of aggregation. Partial aggregation is applied to the linear multicommodity minimum cost flow problem. The possibility of having only partially aggregated bundles opens a wide range of alternatives with different trade-offs between the number of iterations and the required computation for solving it. This trade-off is explored for several sets of instances and the results are compared with the ones obtained by directly solving the natural node-arc formulation. An iterative solution process to the route assignment problem is proposed, based on the well-known Frank Wolfe algorithm. In order to provide a first feasible solution to the Frank Wolfe algorithm, a linear multicommodity min-cost flow problem is solved to optimality by using the decomposition techniques mentioned above. Solutions of this problem are useful for network orientation and design, especially in relation with public transportation systems as the Personal Rapid Transit. A single-commodity robust network design problem is addressed. In this, an undirected graph with edge costs is given together with a discrete set of balance matrices, representing different supply/demand scenarios. The goal is to determine the minimum cost installation of capacities on the edges such that the flow exchange is feasible for every scenario. A set of new instances that are computationally hard for the natural flow formulation are solved by means of a new heuristic algorithm. Finally, an efficient decomposition-based heuristic approach for a large scale stochastic unit commitment problem is presented. The addressed real-world stochastic problem employs at its core a deterministic unit commitment planning model developed by the California Independent System Operator (ISO).