Development and characterization of micromachined devices for separation techniques

Nowadays microfluidic is becoming an important technology in many chemical and biological processes and analysis applications. The potential to replace large-scale conventional laboratory instrumentation with miniaturized and self-contained systems, (called lab-on-a-chip (LOC) or point-of-care-testing (POCT)), offers a variety of advantages such as low reagent consumption, faster analysis speeds, and the capability of operating in a massively parallel scale in order to achieve high-throughput. Micro-electro-mechanical-systems (MEMS) technologies enable both the fabrication of miniaturized system and the possibility of developing compact and portable systems. The work described in this dissertation is towards the development of micromachined separation devices for both high-speed gas chromatography (HSGC) and gravitational field-flow fractionation (GrFFF) using MEMS technologies. Concerning the HSGC, a complete platform of three MEMS-based GC core components (injector, separation column and detector) is designed, fabricated and characterized. The microinjector consists of a set of pneumatically driven microvalves, based on a polymeric actuating membrane. Experimental results demonstrate that the microinjector is able to guarantee low dead volumes, fast actuation time, a wide operating temperature range and high chemical inertness. The microcolumn consists of an all-silicon microcolumn having a nearly circular cross-section channel. The extensive characterization has produced separation performances very close to the theoretical ideal expectations. A thermal conductivity detector (TCD) is chosen as most proper detector to be miniaturized since the volume reduction of the detector chamber results in increased mass and reduced dead volumes. The microTDC shows a good sensitivity and a very wide dynamic range. Finally a feasibility study for miniaturizing a channel suited for GrFFF is performed. The proposed GrFFF microchannel is at early stage of development, but represents a first step for the realization of a highly portable and potentially low-cost POCT device for biomedical applications.

Transport Properties and Novel Sensing Applications of Organic Semiconducting Crystals

The present thesis is focused on the study of Organic Semiconducting Single Crystals (OSSCs) and crystalline thin films. In particular solution-grown OSSC, e.g. 4-hdroxycyanobenzene (4HCB) have been characterized in view of their applications as novel sensors of X-rays, gamma-rays, alpha particles radiations and chemical sensors. In the field of ionizing radiation detection, organic semiconductors have been proposed so far mainly as indirect detectors, i.e. as scintillators or as photodiodes. I first study the performance of 4HCB single crystals as direct X-ray detector i.e. the direct photon conversion into an electrical signal, assessing that they can operate at room temperature and in atmosphere, showing a stable and linear response with increasing dose rate. A dedicated study of the collecting electrodes geometry, crystal thickness and interaction volume allowed us to maximize the charge collection efficiency and sensitivity, thus assessing how OSSCs perform at low operating voltages and offer a great potential in the development of novel ionizing radiation sensors. To better understand the processes generating the observed X-ray signal, a comparative study is presented on OSSCs based on several small-molecules: 1,5-dinitronaphthalene (DNN), 1,8-naphthaleneimide (NTI), Rubrene and TIPS-pentacene. In addition, the proof of principle of gamma-rays and alpha particles has been assessed for 4HCB single crystals. I have also carried out an investigation of the electrical response of OSSCs exposed to vapour of volatile molecules, polar and non-polar. The last chapter deals with rubrene, the highest performing molecular crystals for electronic applications. We present an investigation on high quality, millimeter-sized, crystalline thin films (10 – 100 nm thick) realized by exploiting organic molecular beam epitaxy on water-soluble substrates. Space-Charge-Limited Current (SCLC) and photocurrent spectroscopy measurements have been carried out. A thin film transistor was fabricated onto a Cytop® dielectric layer. The FET mobility exceeding 2 cm2/Vs, definitely assess the quality of RUB films.

Caratterizzazione avanzata in laboratorio di materie prime secondarie rigenerate o stabilizzate con emulsione di bitume e leganti cementizi

Il recupero dei materiali di scarto è un aspetto di grande attualità in campo stradale, così come negli altri ambiti dell’ingegneria civile. L’attenzione della ricerca e degli esperti del settore è rivolta all’affinamento di tecniche di riciclaggio che riducano l’impatto ambientale senza compromettere le prestazioni meccaniche finali. Tali indagini cercano di far corrispondere le necessità di smaltimento dei rifiuti con quelle dell’industria infrastrutturale, legate al reperimento di materiali da costruzione tecnicamente idonei ed economicamente vantaggiosi. Attualmente sono già diversi i tipi di prodotti rigenerati e riutilizzati nella realizzazione delle pavimentazioni stradali e numerosi sono anche quelli di nuova introduzione in fase di sperimentazione. In particolare, accanto ai materiali derivanti dalle operazioni di recupero della rete viaria, è opportuno considerare anche quelli provenienti dall’esercizio delle attività di trasporto, il quale comporta ogni anno il raggiungimento della fine della vita utile per centinaia di migliaia di tonnellate di pneumatici di gomma. L’obiettivo della presente analisi sperimentale è quello di fornire indicazioni e informazioni in merito alla tecnica di riciclaggio a freddo con emulsione bituminosa e cemento, valutando la possibilità di applicazione di tale metodologia in combinazione con il polverino di gomma, ottenuto dal recupero degli pneumatici fuori uso (PFU). La ricerca si distingue per una duplice valenza: la prima è quella di promuovere ulteriormente la tecnica di riciclaggio a freddo, che si sta imponendo per i suoi numerosi vantaggi economici ed ambientali, legati soprattutto alla temperatura d’esercizio; la seconda è quella di sperimentare l’utilizzo del polverino di gomma, nelle due forme di granulazione tradizionale e criogenica, additivato a miscele costituite interamente da materiale proveniente da scarifica di pavimentazioni esistenti e stabilizzate con diverse percentuali di emulsione di bitume e di legante cementizio.