Physical and mineralogical changes of Hungarian monumental stones exposed to different conditions: stone-testing in-situ and under laboratory conditions

The Székesfehérvár Ruin Garden is a unique assemblage of monuments belonging to the cultural heritage of Hungary due to its important role in the Middle Ages as the coronation and burial church of the Kings of the Hungarian Christian Kingdom. It has been nominated for “National Monument” and as a consequence, its protection in the present and future is required. Moreover, it was reconstructed and expanded several times throughout Hungarian history. By a quick overview of the current state of the monument, the presence of several lithotypes can be found among the remained building and decorative stones. Therefore, the research related to the materials is crucial not only for the conservation of that specific monument but also for other historic structures in Central Europe. The current research is divided in three main parts: i) description of lithologies and their provenance, ii) physical properties testing of historic material and iii) durability tests of analogous stones obtained from active quarries. The survey of the National Monument of Székesfehérvár, focuses on the historical importance and the architecture of the monument, the different construction periods, the identification of the different building stones and their distribution in the remaining parts of the monument and it also included provenance analyses. The second one was the in situ and laboratory testing of physical properties of historic material. As a final phase samples were taken from local quarries with similar physical and mineralogical characteristics to the ones used in the monument. The three studied lithologies are: fine oolitic limestone, a coarse oolitic limestone and a red compact limestone. These stones were used for rock mechanical and durability tests under laboratory conditions. The following techniques were used: a) in-situ: Schmidt Hammer Values, moisture content measurements, DRMS, mapping (construction ages, lithotypes, weathering forms) b) laboratory: petrographic analysis, XRD, determination of real density by means of helium pycnometer and bulk density by means of mercury pycnometer, pore size distribution by mercury intrusion porosimetry and by nitrogen adsorption, water absorption, determination of open porosity, DRMS, frost resistance, ultrasonic pulse velocity test, uniaxial compressive strength test and dynamic modulus of elasticity. The results show that initial uniaxial compressive strength is not necessarily a clear indicator of the stone durability. Bedding and other lithological heterogeneities can influence the strength and durability of individual specimens. In addition, long-term behaviour is influenced by exposure conditions, fabric and, especially, the pore size distribution of each sample. Therefore, a statistic evaluation of the results is highly recommended and they should be evaluated in combination with other investigations on internal structure and micro-scale heterogeneities of the material, such as petrographic observation, ultrasound pulse velocity and porosimetry. Laboratory tests used to estimate the durability of natural stone may give a good guidance to its short-term performance but they should not be taken as an ultimate indication of the long-term behaviour of the stone. The interdisciplinary study of the results confirms that stones in the monument show deterioration in terms of mineralogy, fabric and physical properties in comparison with quarried stones. Moreover stone-testing proves compatibility between quarried and historical stones. Good correlation is observed between the non-destructive-techniques and laboratory tests results which allow us to minimize sampling and assessing the condition of the materials. Concluding, this research can contribute to the diagnostic knowledge for further studies that are needed in order to evaluate the effect of recent and future protective measures.

Evaluation of slope stability under water and seismic load through the Minimum Lithostatic Deviation method

The main objective of this thesis is to obtain a better understanding of the methods to assess the stability of a slope. We have illustrated the principal variants of the Limit Equilibrium (LE) method found in literature, focalizing our attention on the Minimum Lithostatic Deviation (MLD) method, developed by Prof. Tinti and his collaborators (e.g. Tinti and Manucci, 2006, 2008). We had two main goals: the first was to test the MLD method on some real cases. We have selected the case of the Vajont landslide with the objective to reconstruct the conditions that caused the destabilization of Mount Toc, and two sites in the Norwegian margin, where failures has not occurred recently, with the aim to evaluate the present stability state and to assess under which conditions they might be mobilized. The second goal was to study the stability charts by Taylor and by Michalowski, and to use the MLD method to investigate the correctness and adequacy of this engineering tool.

Farming and processing factors for improving quality properties of poultry and rabbit meat

Recently, global meat market is facing several dramatic changes due to shifting in diet and life style, consumer demands, and economical considerations. Firstly, there was a tremendous increase in the poultry meat demand. Furthermore, current forecast and projection studies pointed out that the expansion of the poultry market will continue in future. In response to this demand, there was a great success to increase growth rate of meat-type chickens in the last few decades in order to optimize the production of poultry meat. Accordingly, the increase of growth rate induced the appearance of several muscle abnormalities such as pale-soft-exudative (PSE) syndrome and deep-pectoral-myopathy (DPM) and more recently white striping and wooden breast. Currently, there is growing interest in meat industry to understand how much the magnitude of the effect of these abnormalities on different quality traits for raw and processed meat. Therefore, the major part of the research activities during the PhD project was dedicated to evaluate the different implications of recent muscle abnormalities such as white striping and wooden breast on meat quality traits and their incidence under commercial conditions. Generally, our results showed that the incidence of these muscle abnormalities was very high under commercial conditions and had great adverse impact on meat quality traits. Secondly, there is growing market share of convenient, healthy, and functional processed meat products. Accordingly, the remaining part of research activities of the PhD project was dedicated to evaluate the possibility to formulate processed meat products with higher perceived healthy profile such as phosphate free-marinated chicken meat and low sodium-marinated rabbit meat products. Overall all findings showed that sodium bicarbonate can be considered as promising component to replace phosphates in meat products, while potassium chloride under certain conditions was successfully used to produce low marinated rabbit meat products.