Architectural development and dry matter production in a multisite trial on single and multiaxis apple trees (Malus domestica Borkh) grafted on different rootstocks

In two Italian sites, multiaxis trees slightly reduced primary axis length and secondary axis length of newly grafted trees, and increased the number of secondary shoots. The total length, node production, and total dry matter gain were proportional to the number of axis. Growth of both primary and secondary shoots, and dry matter accumulation, have been found to be also well related to rootstock vigour. A great variability in axillary shoot production was recorded among different environments. Grafted trees had higher primary growth, secondary axis growth, and dry matter gain than chip budded trees. Stem water potential measured in the second year after grafting was not affected by rootstocks or number of leaders. Measurements performed in New Zealand (Hawke’s Bay) during the second year after grafting revealed that both final length and growth rate of primary and secondary axis were related to the rootstock rather than to the training system. Dwarfing rootstocks reduced the number of long vegetative shoots and increased the proportion of less vigorous shoots.

Food safety in wine: optimization of analytical controls and evaluation of production technologies

This PhD thesis has been proposed to validate and then apply innovative analytical methodologies for the determination of compounds with harmful impact on human health, such as biogenic amines and ochratoxin A in wines. Therefore, the influence of production technology (pH, amino acids precursor and use of different malolactic starters) on biogenic amines content in wines was evaluated. An HPLC method for simultaneous determination of amino acids and amines with precolumnderivatization with 9-Fluorenyl-methoxycarbonyl chloride (FMOC-Cl) and UV detection was developed. Initially, the influence of pH, time of derivatization, gradient profile were studied. In order to improve the separation of amino acids and amines and reduce the time of analysis, it was decided to study the influence of different flows and the use of different columns in the chromatographic method. Firstly, a C18 Luna column was used and later two monolithic columns Chromolith in series. It appeared to be suitable for an easy, precise and accurate determination of a relatively large number of amino acids and amines in wines. This method was then applied on different wines produced in the Emilia Romagna region. The investigation permitted to discriminate between red and white wines. Amino acids content is related to the winemaking process. Biogenic amines content in these wines does not represent a possible toxicological problem for human health. The results of the study of influence of technologies and wine composition demonstrated that pH of wines and amino acids content are the most important factors. Particularly wines with pH > 3,5 show higher concentration of biogenic amines than wines with lower pH. The enrichment of wines by nutrients also influences the content of some biogenic amines that are higher in wines added with amino acids precursors. In this study, amino acids and biogenic amines are not statistically affected by strain of lactic acid bacteria inoculated as a starter for malolactic fermentation. An evaluation of different clean-up (SPE-MycoSep; IACs and LLE) and determination methods (HPLC and ELISA) of ochratoxin A was carried out. The results obtained proved that the SPE clean-up are reliable at the same level while the LLE procedures shows lowest recovery. The ELISA method gave a lower determination and a low reproducibility than HPLC method.

Development and characterization of non-oxide ceramic composites for mechanical and tribological applications

The main reasons for the attention focused on ceramics as possible structural materials are their wear resistance and the ability to operate with limited oxidation and ablation at temperatures above 2000°C. Hence, this work is devoted to the study of two classes of materials which can satisfy these requirements: silicon carbide -based ceramics (SiC) for wear applications and borides and carbides of transition metals for ultra-high temperatures applications (UHTCs). SiC-based materials: Silicon carbide is a hard ceramic, which finds applications in many industrial sectors, from heat production, to automotive engineering and metals processing. In view of new fields of uses, SiC-based ceramics were produced with addition of 10-30 vol% of MoSi2, in order to obtain electro conductive ceramics. MoSi2, indeed, is an intermetallic compound which possesses high temperature oxidation resistance, high electrical conductivity (21·10-6 Ω·cm), relatively low density (6.31 g/cm3), high melting point (2030°C) and high stiffness (440 GPa). The SiC-based ceramics were hot pressed at 1900°C with addition of Al2O3-Y2O3 or Y2O3-AlN as sintering additives. The microstructure of the composites and of the reference materials, SiC and MoSi2, were studied by means of conventional analytical techniques, such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (SEM-EDS). The composites showed a homogeneous microstructure, with good dispersion of the secondary phases and low residual porosity. The following thermo-mechanical properties of the SiC-based materials were measured: Vickers hardness (HV), Young’s modulus (E), fracture toughness (KIc) and room to high temperature flexural strength (σ). The mechanical properties of the composites were compared to those of two monolithic SiC and MoSi2 materials and resulted in a higher stiffness, fracture toughness and slightly higher flexural resistance. Tribological tests were also performed in two configurations disco-on-pin and slideron cylinder, aiming at studying the wear behaviour of SiC-MoSi2 composites with Al2O3 as counterfacing materials. The tests pointed out that the addition of MoSi2 was detrimental owing to a lower hardness in comparison with the pure SiC matrix. On the contrary, electrical measurements revealed that the addition of 30 vol% of MoSi2, rendered the composite electroconductive, lowering the electrical resistance of three orders of magnitude. Ultra High Temperature Ceramics: Carbides, borides and nitrides of transition metals (Ti, Zr, Hf, Ta, Nb, Mo) possess very high melting points and interesting engineering properties, such as high hardness (20-25 GPa), high stiffness (400-500 GPa), flexural strengths which remain unaltered from room temperature to 1500°C and excellent corrosion resistance in aggressive environment. All these properties place the UHTCs as potential candidates for the development of manoeuvrable hypersonic flight vehicles with sharp leading edges. To this scope Zr- and Hf- carbide and boride materials were produced with addition of 5-20 vol% of MoSi2. This secondary phase enabled the achievement of full dense composites at temperature lower than 2000°C and without the application of pressure. Besides the conventional microstructure analyses XRD and SEM-EDS, transmission electron microscopy (TEM) was employed to explore the microstructure on a small length scale to disclose the effective densification mechanisms. A thorough literature analysis revealed that neither detailed TEM work nor reports on densification mechanisms are available for this class of materials, which however are essential to optimize the sintering aids utilized and the processing parameters applied. Microstructural analyses, along with thermodynamics and crystallographic considerations, led to disclose of the effective role of MoSi2 during sintering of Zrand Hf- carbides and borides. Among the investigated mechanical properties (HV, E, KIc, σ from room temperature to 1500°C), the high temperature flexural strength was improved due to the protective and sealing effect of a silica-based glassy phase, especially for the borides. Nanoindentation tests were also performed on HfC-MoSi2 composites in order to extract hardness and elastic modulus of the single phases. Finally, arc jet tests on HfC- and HfB2-based composites confirmed the excellent oxidation behaviour of these materials under temperature exceeding 2000°C; no cracking or spallation occurred and the modified layer was only 80-90 μm thick.

Aureobasidium pullulans as biological control agent: modes of action

The postharvest phase has been considered an environment very suitable for successful application of biological control agents (BCAs). However, the tri-interaction between fungal pathogen, host (fruit) and antagonist is influenced by several parameters such as temperature, oxidative stresses, oxygen composition, water activity, etc. that could be determining for the success of biocontrol. Knowledge of the modes of action of BCAs is essential in order to enhance their viability and increase their potentialities in disease control. The thesis focused on the possibility to explain the modes of action of a biological control agent (BCA): Aureobasidium pullulans, in particular the strains L1 and L8, control effective against fruit postharvest fungal pathogen. In particular in this work were studied the different modes of action of BCA, such as: i) the ability to produce volatile organic compounds (VOCs), identified by SPME- gas chromatography-mass spectrometry (GC-MS) and tested by in vitro and in vivo assays against Penicillium spp., Botrytis cinerea, Colletotrichum acutatum; ii) the ability to produce lytic enzymes (exo and endo chitinase and β-1,3-glucanase) tested against Monilinia laxa, causal agent of brown rot of stone fruits. L1 and L8 lytic enzymes were also evaluated through their relative genes by molecular tools; iii) the competition for space and nutrients, such as sugars (sucrose, glucose and fructose) and iron; the latter induced the production of siderophores, molecules with high affinity for iron chelation. A molecular investigation was carried out to better understand the gene regulation strictly correlated to the production of these chelating molucules. The competition for space against M. laxa was verified by electron microscopy techniques; iv) a depth bibliographical analysis on BCAs mechanisms of action and their possible combination with physical and chemical treatments was conducted.

What Happened to Participation? Urban Development and Authoritarian Upgrading in Cairo's Informal Neighbourhoods

Participation appeared in development discourses for the first time in the 1970s, as a generic call for the involvement of the poor in development initiatives. Over the last three decades, the initial perspectives on participation intended as a project method for poverty reduction have evolved into a coherent and articulated theoretical elaboration, in which participation figures among the paraphernalia of good governance promotion: participation has acquired the status of “new orthodoxy”. Nevertheless, the experience of the implementation of participatory approaches in development projects seemed to be in the majority of cases rather disappointing, since the transformative potential of ‘participation in development’ depends on a series of factors in which every project can actually differ from others: the ultimate aim of the approach promoted, its forms and contents and, last but not least, the socio-political context in which the participatory initiative is embedded. In Egypt, the signature of a project agreement between the Arab Republic of Egypt and the Federal Republic of Germany, in 1998, inaugurated a Participatory Urban Management Programme (PUMP) to be implemented in Greater Cairo by the German Technical Cooperation (Deutsche Gesellschaft für Technische Zusammenarbeit, GTZ) and the Ministry of Planning (now Ministry of Local Development) and the Governorates of Giza and Cairo as the main counterparts. Now, ten years after the beginning of the PUMP/PDP and close to its end (December 2010), it is possible to draw some conclusions about the scope, the significance and the effects of the participatory approach adopted by GTZ and appropriated by the Egyptian counterparts in dealing with the issue of informal areas and, more generally, of urban development. Our analysis follows three sets of questions: the first set regards the way ‘participation’ has been interpreted and concretised by PUMP and PDP. The second is about the emancipating potential of the ‘participatory approach’ and its ability to ‘empower’ the ‘marginalised’. The third focuses on one hand on the efficacy of GTZ strategy to lead to an improvement of the delivery service in informal areas (especially in terms of planning and policies), and on the other hand on the potential of GTZ development intervention to trigger an incremental process of ‘democratisation’ from below.