Development of quantitative methods for sustainability assessment in process industry

The increasing aversion to technological risks of the society requires the development of inherently safer and environmentally friendlier processes, besides assuring the economic competitiveness of the industrial activities. The different forms of impact (e.g. environmental, economic and societal) are frequently characterized by conflicting reduction strategies and must be holistically taken into account in order to identify the optimal solutions in process design. Though the literature reports an extensive discussion of strategies and specific principles, quantitative assessment tools are required to identify the marginal improvements in alternative design options, to allow the trade-off among contradictory aspects and to prevent the “risk shift”. In the present work a set of integrated quantitative tools for design assessment (i.e. design support system) was developed. The tools were specifically dedicated to the implementation of sustainability and inherent safety in process and plant design activities, with respect to chemical and industrial processes in which substances dangerous for humans and environment are used or stored. The tools were mainly devoted to the application in the stages of “conceptual” and “basic design”, when the project is still open to changes (due to the large number of degrees of freedom) which may comprise of strategies to improve sustainability and inherent safety. The set of developed tools includes different phases of the design activities, all through the lifecycle of a project (inventories, process flow diagrams, preliminary plant lay-out plans). The development of such tools gives a substantial contribution to fill the present gap in the availability of sound supports for implementing safety and sustainability in early phases of process design. The proposed decision support system was based on the development of a set of leading key performance indicators (KPIs), which ensure the assessment of economic, societal and environmental impacts of a process (i.e. sustainability profile). The KPIs were based on impact models (also complex), but are easy and swift in the practical application. Their full evaluation is possible also starting from the limited data available during early process design. Innovative reference criteria were developed to compare and aggregate the KPIs on the basis of the actual sitespecific impact burden and the sustainability policy. Particular attention was devoted to the development of reliable criteria and tools for the assessment of inherent safety in different stages of the project lifecycle. The assessment follows an innovative approach in the analysis of inherent safety, based on both the calculation of the expected consequences of potential accidents and the evaluation of the hazards related to equipment. The methodology overrides several problems present in the previous methods proposed for quantitative inherent safety assessment (use of arbitrary indexes, subjective judgement, build-in assumptions, etc.). A specific procedure was defined for the assessment of the hazards related to the formations of undesired substances in chemical systems undergoing “out of control” conditions. In the assessment of layout plans, “ad hoc” tools were developed to account for the hazard of domino escalations and the safety economics. The effectiveness and value of the tools were demonstrated by the application to a large number of case studies concerning different kinds of design activities (choice of materials, design of the process, of the plant, of the layout) and different types of processes/plants (chemical industry, storage facilities, waste disposal). An experimental survey (analysis of the thermal stability of isomers of nitrobenzaldehyde) provided the input data necessary to demonstrate the method for inherent safety assessment of materials.

Architectures and design patterns for functional design of logic control and diagnostics in industrial automation

Recently in most of the industrial automation process an ever increasing degree of automation has been observed. This increasing is motivated by the higher requirement of systems with great performance in terms of quality of products/services generated, productivity, efficiency and low costs in the design, realization and maintenance. This trend in the growth of complex automation systems is rapidly spreading over automated manufacturing systems (AMS), where the integration of the mechanical and electronic technology, typical of the Mechatronics, is merging with other technologies such as Informatics and the communication networks. An AMS is a very complex system that can be thought constituted by a set of flexible working stations, one or more transportation systems. To understand how this machine are important in our society let considerate that every day most of us use bottles of water or soda, buy product in box like food or cigarets and so on. Another important consideration from its complexity derive from the fact that the the consortium of machine producers has estimated around 350 types of manufacturing machine. A large number of manufacturing machine industry are presented in Italy and notably packaging machine industry,in particular a great concentration of this kind of industry is located in Bologna area; for this reason the Bologna area is called “packaging valley”. Usually, the various parts of the AMS interact among them in a concurrent and asynchronous way, and coordinate the parts of the machine to obtain a desiderated overall behaviour is an hard task. Often, this is the case in large scale systems, organized in a modular and distributed manner. Even if the success of a modern AMS from a functional and behavioural point of view is still to attribute to the design choices operated in the definition of the mechanical structure and electrical electronic architecture, the system that governs the control of the plant is becoming crucial, because of the large number of duties associated to it. Apart from the activity inherent to the automation of themachine cycles, the supervisory system is called to perform other main functions such as: emulating the behaviour of traditional mechanical members thus allowing a drastic constructive simplification of the machine and a crucial functional flexibility; dynamically adapting the control strategies according to the different productive needs and to the different operational scenarios; obtaining a high quality of the final product through the verification of the correctness of the processing; addressing the operator devoted to themachine to promptly and carefully take the actions devoted to establish or restore the optimal operating conditions; managing in real time information on diagnostics, as a support of the maintenance operations of the machine. The kind of facilities that designers can directly find on themarket, in terms of software component libraries provides in fact an adequate support as regard the implementation of either top-level or bottom-level functionalities, typically pertaining to the domains of user-friendly HMIs, closed-loop regulation and motion control, fieldbus-based interconnection of remote smart devices. What is still lacking is a reference framework comprising a comprehensive set of highly reusable logic control components that, focussing on the cross-cutting functionalities characterizing the automation domain, may help the designers in the process of modelling and structuring their applications according to the specific needs. Historically, the design and verification process for complex automated industrial systems is performed in empirical way, without a clear distinction between functional and technological-implementation concepts and without a systematic method to organically deal with the complete system. Traditionally, in the field of analog and digital control design and verification through formal and simulation tools have been adopted since a long time ago, at least for multivariable and/or nonlinear controllers for complex time-driven dynamics as in the fields of vehicles, aircrafts, robots, electric drives and complex power electronics equipments. Moving to the field of logic control, typical for industrial manufacturing automation, the design and verification process is approached in a completely different way, usually very “unstructured”. No clear distinction between functions and implementations, between functional architectures and technological architectures and platforms is considered. Probably this difference is due to the different “dynamical framework”of logic control with respect to analog/digital control. As a matter of facts, in logic control discrete-events dynamics replace time-driven dynamics; hence most of the formal and mathematical tools of analog/digital control cannot be directly migrated to logic control to enlighten the distinction between functions and implementations. In addition, in the common view of application technicians, logic control design is strictly connected to the adopted implementation technology (relays in the past, software nowadays), leading again to a deep confusion among functional view and technological view. In Industrial automation software engineering, concepts as modularity, encapsulation, composability and reusability are strongly emphasized and profitably realized in the so-calledobject-oriented methodologies. Industrial automation is receiving lately this approach, as testified by some IEC standards IEC 611313, IEC 61499 which have been considered in commercial products only recently. On the other hand, in the scientific and technical literature many contributions have been already proposed to establish a suitable modelling framework for industrial automation. During last years it was possible to note a considerable growth in the exploitation of innovative concepts and technologies from ICT world in industrial automation systems. For what concerns the logic control design, Model Based Design (MBD) is being imported in industrial automation from software engineering field. Another key-point in industrial automated systems is the growth of requirements in terms of availability, reliability and safety for technological systems. In other words, the control system should not only deal with the nominal behaviour, but should also deal with other important duties, such as diagnosis and faults isolations, recovery and safety management. Indeed, together with high performance, in complex systems fault occurrences increase. This is a consequence of the fact that, as it typically occurs in reliable mechatronic systems, in complex systems such as AMS, together with reliable mechanical elements, an increasing number of electronic devices are also present, that are more vulnerable by their own nature. The diagnosis problem and the faults isolation in a generic dynamical system consists in the design of an elaboration unit that, appropriately processing the inputs and outputs of the dynamical system, is also capable of detecting incipient faults on the plant devices, reconfiguring the control system so as to guarantee satisfactory performance. The designer should be able to formally verify the product, certifying that, in its final implementation, it will perform itsrequired function guarantying the desired level of reliability and safety; the next step is that of preventing faults and eventually reconfiguring the control system so that faults are tolerated. On this topic an important improvement to formal verification of logic control, fault diagnosis and fault tolerant control results derive from Discrete Event Systems theory. The aimof this work is to define a design pattern and a control architecture to help the designer of control logic in industrial automated systems. The work starts with a brief discussion on main characteristics and description of industrial automated systems on Chapter 1. In Chapter 2 a survey on the state of the software engineering paradigm applied to industrial automation is discussed. Chapter 3 presentes a architecture for industrial automated systems based on the new concept of Generalized Actuator showing its benefits, while in Chapter 4 this architecture is refined using a novel entity, the Generalized Device in order to have a better reusability and modularity of the control logic. In Chapter 5 a new approach will be present based on Discrete Event Systems for the problemof software formal verification and an active fault tolerant control architecture using online diagnostic. Finally conclusive remarks and some ideas on new directions to explore are given. In Appendix A are briefly reported some concepts and results about Discrete Event Systems which should help the reader in understanding some crucial points in chapter 5; while in Appendix B an overview on the experimental testbed of the Laboratory of Automation of University of Bologna, is reported to validated the approach presented in chapter 3, chapter 4 and chapter 5. In Appendix C some components model used in chapter 5 for formal verification are reported.

Dry grinding technology for automotive gears manufacturing: process modeling and optimization

The following thesis focused on the dry grinding process modelling and optimization for automotive gears production. A FEM model was implemented with the aim at predicting process temperatures and preventing grinding thermal defects on the material surface. In particular, the model was conceived to facilitate the choice of the grinding parameters during the design and the execution of the dry-hard finishing process developed and patented by the company Samputensili Machine Tools (EMAG Group) on automotive gears. The proposed model allows to analyse the influence of the technological parameters, comprising the grinding wheel specifications. Automotive gears finished by dry-hard finishing process are supposed to reach the same quality target of the gears finished through the conventional wet grinding process with the advantage of reducing production costs and environmental pollution. But, the grinding process allows very high values of specific pressure and heat absorbed by the material, therefore, removing the lubricant increases the risk of thermal defects occurrence. An incorrect design of the process parameters set could cause grinding burns, which affect the mechanical performance of the ground component inevitably. Therefore, a modelling phase of the process could allow to enhance the mechanical characteristics of the components and avoid waste during production. A hierarchical FEM model was implemented to predict dry grinding temperatures and was represented by the interconnection of a microscopic and a macroscopic approach. A microscopic single grain grinding model was linked to a macroscopic thermal model to predict the dry grinding process temperatures and so to forecast the thermal cycle effect caused by the process parameters and the grinding wheel specification choice. Good agreement between the model and the experiments was achieved making the dry-hard finishing an efficient and reliable technology to implement in the gears automotive industry.

The Simon effect and its time courses: an investigation

The objective of the current thesis is to investigate the temporal dynamics (i.e., time courses) of the Simon effect, both from a theoretical and experimental point of view, for a better understanding of whether a) one or more process are responsible for the Simon effect and b) how this/these mechanism/s differently influence performance. In the first theoretical (i.e., “Theoretical Overview”) part, I examined in detail the process and justification for analyzing the temporal dynamics of the Simon effect and the assumptions that underlie interpretation of the results which have been obtained in the existing literature so far. In the second part (“Experimental Investigations”), though, I experimentally investigated several issues which the existing literature left unsolved, in order to get further evidence in favor or in contrast with the mainstream models which are currently used to account for the different Simon effect time courses. Some points about the experiments are worth mentioning: First, all the experiments were conducted in the laboratory, facing participants with stimuli presented on a PC screen and then recording their responses. Both stimuli presentation and response collection was controlled by the E-Prime software. The dependent variables of interest were always behavioral measures of performance, such as velocity and accuracy. Second, the most part of my experiments had been conducted at the Communication Sciences Department (University of Bologna), under Prof. Nicoletti’s supervision. The remaining part, though, had been conducted at the Psychological Sciences Department of Purdue University (West Lafayette, Indiana, USA), where I collaborated for one year as a visiting student with Prof. Proctor and his team. Third, my experimental pool was entirely composed by healthy and young students, since the cognitive functioning of elderly people was not the target of my research.

Study of medicinal and food plants as a source of biologically active compounds.

In the last few decades, scientific evidence has pointed out the health-beneficial effects of phenolic compounds in foods, including a decrease in risk of developing degenerative and chronic diseases, known to be caused by oxidative stress. In this frame can be inserted research carried out during my PhD thesis, which concerns the phytochemical investigation of phenolic composition in sweet cherries (Prunus avium L.), apple fruits (Malus domestica L.) and quinoa seeds (Chenopodium quinoa Willd.). The first project was focused on the investigation of phytochemical profile and nutraceutical value of fruits of new sweet cherry cultivars. Their phenolic profile and antioxidant activity were investigated and compared with those of commonly commercialized cultivars. Their nutraceutical value was evaluated in terms of antioxidant/neuroprotective capacity in neuron-like SH-SY5Y cells, in order to investigate their ability to counteract the oxidative stress and/or neurodegeneration process The second project was focused on phytochemical analysis of phenolic compounds in apples of ancient cultivars with the aim of selecting the most diverse cultivars, that will then be assayed for their anti-carcinogenic and anti-proliferative activities against the hepato-biliary and pancreatic tumours. The third project was focused on the analysis of polyphenolic pattern of seeds of two quinoa varieties grown at different latitudes. Analysis of phenolic profile and in vitro antioxidant activity of seed extracts both in their free and soluble-conjugated forms, showed that the accumulation of some classes of flavonoids is strictly regulated by environmental factors, even though the overall antioxidant capacity does not differ in quinoa Regalona grown in Chile and Italy. During the internship period carried out at the Department of Organic Chemistry at Universidad Autónoma de Madrid (UAM), it was achieved the isolation of two pentacyclic triterpenoids, from an endemic Peruvian plant, Jatropha macrantha Müll. Arg., with bio-guided fractionation technique.

Development and testing of methodologies for the control and diagnosis of innovative combustion systems

In pursuit of aligning with the European Union's ambitious target of achieving a carbon-neutral economy by 2050, researchers, vehicle manufacturers, and original equipment manufacturers have been at the forefront of exploring cutting-edge technologies for internal combustion engines. The introduction of these technologies has significantly increased the effort required to calibrate the models implemented in the engine control units. Consequently the development of tools that reduce costs and the time required during the experimental phases, has become imperative. Additionally, to comply with ever-stricter limits on 〖"CO" 〗_"2" emissions, it is crucial to develop advanced control systems that enhance traditional engine management systems in order to reduce fuel consumption. Furthermore, the introduction of new homologation cycles, such as the real driving emissions cycle, compels manufacturers to bridge the gap between engine operation in laboratory tests and real-world conditions. Within this context, this thesis showcases the performance and cost benefits achievable through the implementation of an auto-adaptive closed-loop control system, leveraging in-cylinder pressure sensors in a heavy-duty diesel engine designed for mining applications. Additionally, the thesis explores the promising prospect of real-time self-adaptive machine learning models, particularly neural networks, to develop an automatic system, using in-cylinder pressure sensors for the precise calibration of the target combustion phase and optimal spark advance in a spark-ignition engines. To facilitate the application of these combustion process feedback-based algorithms in production applications, the thesis discusses the results obtained from the development of a cost-effective sensor for indirect cylinder pressure measurement. Finally, to ensure the quality control of the proposed affordable sensor, the thesis provides a comprehensive account of the design and validation process for a piezoelectric washer test system.

At the intersection of Behavioural Economics, Nudging and Regulation: Rethinking the process of nudge design for regulation

Alongside the developments in behavioural economics, the concept of nudge was introduced as an intervention able to guide individual behaviour towards better choices without using coercion or incentives. While behavioural teams were created inside governmental units and regulatory authorities, nudging emerged in regulatory discourse, being increasingly regarded as a regulatory instrument that could overcome the disadvantages of other tools. This thesis analyses the viability of incorporating nudges into regulation. In particular, it investigates the implications for regulators of bringing iterative experimental testing – a widespread nudge design methodology outside regulation – into their own design practices. Nudges outside regulation are routinely designed using experiments of all kinds. This thesis intends to answer whether design premises rooted in iterative experimentation are still valid in the regulatory space, an arena that nudging entered into and that is distinct from the one where it originally emerged. The design and provision of nudges using the premises of iterative experimental testing is possible, but at a cost and burden for regulatory nudge designers. Therefore, the thesis evaluates how this burden can be reduced, in particular how nudges can be feasibly designed and provided through regulation or, put differently, how to more efficiently design and provide nudging as a regulatory tool.

L'eredità di Aldo Rossi nella Penisola Iberica. La costruzione della città e il progetto contemporaneo

Descrizione, tema e obiettivi della ricerca La ricerca si propone lo studio delle possibili influenze che la teoria di Aldo Rossi ha avuto sulla pratica progettuale nella Penisola Iberica, intende quindi affrontare i caratteri fondamentali della teoria che sta alla base di un metodo progettuale ed in particolar modo porre l'attenzione alle nuove costruzioni quando queste si confrontano con le città storiche. Ha come oggetto principale lo studio dei documenti, saggi e scritti riguardanti il tema della costruzione all'interno delle città storiche. Dallo studio di testi selezionati di Aldo Rossi sulla città si vuole concentrare l'attenzione sull'influenza che tale teoria ha avuto nei progetti della Penisola Iberica, studiare come è stata recepita e trasmessa successivamente, attraverso gli scritti di autori spagnoli e come ha visto un suo concretizzarsi poi nei progetti di nuove costruzioni all'interno delle città storiche. Si intende restringere il campo su un periodo ed un luogo precisi, Spagna e Portogallo a partire dagli anni Settanta, tramite la lettura di un importante evento che ha ufficializzato il contatto dell'architetto italiano con la Penisola Iberica, quale il Seminario di Santiago de Compostela tenutosi nel 1976. Al Seminario parteciparono numerosi architetti che si confrontarono su di un progetto per la città di Santiago e furono invitati personaggi di fama internazionale a tenere lezioni introduttive sul tema di dibattito in merito al progetto e alla città storica. Il Seminario di Santiago si colloca in un periodo storico cruciale per la Penisola Iberica, nel 1974 cade il regime salazarista in Portogallo e nel 1975 cade il regime franchista in Spagna ed è quindi di rilevante importanza capire il legame tra l'architettura e la nuova situazione politica. Dallo studio degli interventi, dei progetti che furono prodotti durante il Seminario, della relazione tra questo evento ed il periodo storico in cui esso va contestualizzato, si intende giungere alla individuazione delle tracce della reale presenza di tale eredità. Presupposti metodologici. Percorso e strumenti di ricerca La ricerca può quindi essere articolata in distinte fasi corrispondenti per lo più ai capitoli in cui si articola la tesi: una prima fase con carattere prevalentemente storica, di ricerca del materiale per poter definire il contesto in cui si sviluppano poi le vicende oggetto della tesi; una seconda fase di impronta teorica, ossia di ricerca bibliografica del materiale e delle testimonianze che provvedono alla definizione della reale presenza di effetti scaturiti dai contatti tra Rossi e la Penisola Iberica, per andare a costruire una eredità ; una terza fase che entra nel merito della composizione attraverso lo studio e la verifica delle prime due parti, tramite l'analisi grafica applicata ad uno specifico esempio architettonico selezionato; una quarta fase dove il punto di vista viene ribaltato e si indaga l'influenza dei luoghi visitati e dei contatti intrattenuti con alcuni personaggi della Penisola Iberica sull'architettura di Rossi, ricercandone i riferimenti. La ricerca è stata condotta attraverso lo studio di alcuni eventi selezionati nel corso degli anni che si sono mostrati significativi per l'indagine, per la risonanza che hanno avuto sulla storia dell'architettura della Penisola. A questo scopo si sono utilizzati principalmente tre strumenti: lo studio dei documenti, le pubblicazioni e le riviste prodotte in Spagna, gli scritti di Aldo Rossi in merito, e la testimonianza diretta attraverso interviste di personaggi chiave. La ricerca ha prodotto un testo suddiviso per capitoli che rispetta l'organizzazione in fasi di lavoro. A seguito di determinate condizioni storiche e politiche, studiate nella ricerca a supporto della tesi espressa, nella Penisola Iberica si è verificato il diffondersi della necessità e del desiderio di guardare e prendere a riferimento l'architettura europea e in particolar modo quella italiana. Il periodo sul quale viene focalizzata l'attenzione ha inizio negli anni Sessanta, gli ultimi prima della caduta delle dittature, scenario dei primi viaggi di Aldo Rossi nella Penisola Iberica. Questi primi contatti pongono le basi per intense e significative relazioni future. Attraverso l'approfondimento e la studio dei materiali relativi all'oggetto della tesi, si è cercato di mettere in luce il contesto culturale, l'attenzione e l'interesse per l'apertura di un dibattito intorno all'architettura, non solo a livello nazionale, ma europeo. Ciò ha evidenziato il desiderio di innescare un meccanismo di discussione e scambio di idee, facendo leva sull'importanza dello sviluppo e ricerca di una base teorica comune che rende coerente i lavori prodotti nel panorama architettonico iberico, seppur ottenendo risultati che si differenziano gli uni dagli altri. E' emerso un forte interesse per il discorso teorico sull'architettura, trasmissibile e comunicabile, che diventa punto di partenza per un metodo progettuale. Ciò ha reso palese una condivisione di intenti e l'assunzione della teoria di Aldo Rossi, acquisita, diffusa e discussa, attraverso la pubblicazione dei suoi saggi, la conoscenza diretta con l'architetto e la sua architettura, conferenze, seminari, come base teorica su cui fondare il proprio sapere architettonico ed il processo metodologico progettuale da applicare di volta in volta negli interventi concreti. Si è giunti così alla definizione di determinati eventi che hanno permesso di entrare nel profondo della questione e di sondare la relazione tra Rossi e la Penisola Iberica, il materiale fornito dallo studio di tali episodi, quali il I SIAC, la diffusione della rivista "2C. Construccion de la Ciudad", la Coleccion Arquitectura y Critica di Gustavo Gili, hanno poi dato impulso per il reperimento di una rete di ulteriori riferimenti. E' stato possibile quindi individuare un gruppo di architetti spagnoli, che si identificano come allievi del maestro Rossi, impegnato per altro in quegli anni nella formazione di una Scuola e di un insegnamento, che non viene recepito tanto nelle forme, piuttosto nei contenuti. I punti su cui si fondano le connessioni tra l'analisi urbana e il progetto architettonico si centrano attorno due temi di base che riprendono la teoria esposta da Rossi nel saggio L'architettura della città : - relazione tra l'area-studio e la città nella sua globalità, - relazione tra la tipologia edificatoria e gli aspetti morfologici. La ricerca presentata ha visto nelle sue successive fasi di approfondimento, come si è detto, lo sviluppo parallelo di più tematiche. Nell'affrontare ciascuna fase è stato necessario, di volta in volta, operare una verifica delle tappe percorse precedentemente, per mantenere costante il filo del discorso col lavoro svolto e ritrovare, durante lo svolgimento stesso della ricerca, gli elementi di connessione tra i diversi episodi analizzati. Tale operazione ha messo in luce talvolta nodi della ricerca rimasti in sospeso che richiedevano un ulteriore approfondimento o talvolta solo una rivisitazione per renderne possibile un più proficuo collegamento con la rete di informazioni accumulate. La ricerca ha percorso strade diverse che corrono parallele, per quanto riguarda il periodo preso in analisi: - i testi sulla storia dell'architettura spagnola e la situazione contestuale agli anni Settanta - il materiale riguardante il I SIAC - le interviste ai partecipanti al I SIAC - le traduzioni di Gustavo Gili nella Coleccion Arquitectura y Critica - la rivista "2C. Construccion de la Ciudad" Esse hanno portato alla luce una notevole quantità di tematiche, attraverso le quali, queste strade vengono ad intrecciarsi e a coincidere, verificando l'una la veridicità dell'altra e rafforzandone il valore delle affermazioni. Esposizione sintetica dei principali contenuti esposti dalla ricerca Andiamo ora a vedere brevemente i contenuti dei singoli capitoli. Nel primo capitolo Anni Settanta. Periodo di transizione per la Penisola Iberica si è cercato di dare un contesto storico agli eventi studiati successivamente, andando ad evidenziare gli elementi chiave che permettono di rintracciare la presenza della predisposizione ad un cambiamento culturale. La fase di passaggio da una condizione di chiusura rispetto alle contaminazioni provenienti dall'esterno, che caratterizza Spagna e Portogallo negli anni Sessanta, lascia il posto ad un graduale abbandono della situazione di isolamento venutasi a creare intorno al Paese a causa del regime dittatoriale, fino a giungere all'apertura e all'interesse nei confronti degli apporti culturali esterni. E' in questo contesto che si gettano le basi per la realizzazione del I Seminario Internazionale di Architettura Contemporanea a Santiago de Compostela, del 1976, diretto da Aldo Rossi e organizzato da César Portela e Salvador Tarragó, di cui tratta il capitolo secondo. Questo è uno degli eventi rintracciati nella storia delle relazioni tra Rossi e la Penisola Iberica, attraverso il quale è stato possibile constatare la presenza di uno scambio culturale e l'importazione in Spagna delle teorie di Aldo Rossi. Organizzato all'indomani della caduta del franchismo, ne conserva una reminescenza formale. Il capitolo è organizzato in tre parti, la prima si occupa della ricostruzione dei momenti salienti del Seminario Proyecto y ciudad historica, dagli interventi di architetti di fama internazionale, quali lo stesso Aldo Rossi, Carlo Aymonino, James Stirling, Oswald Mathias Ungers e molti altri, che si confrontano sul tema delle città storiche, alle giornate seminariali dedicate all’elaborazione di un progetto per cinque aree individuate all’interno di Santiago de Compostela e quindi dell’applicazione alla pratica progettuale dell’inscindibile base teorica esposta. Segue la seconda parte dello stesso capitolo riguardante La selezione di interviste ai partecipanti al Seminario. Esso contiene la raccolta dei colloqui avuti con alcuni dei personaggi che presero parte al Seminario e attraverso le loro parole si è cercato di approfondire la materia, in particolar modo andando ad evidenziare l’ambiente culturale in cui nacque l’idea del Seminario, il ruolo avuto nella diffusione della teoria di Aldo Rossi in Spagna e la ripercussione che ebbe nella pratica costruttiva. Le diverse interviste, seppur rivolte a persone che oggi vivono in contesti distanti e che in seguito a questa esperienza collettiva hanno intrapreso strade diverse, hanno fatto emergere aspetti comuni, tale unanimità ha dato ancor più importanza al valore di testimonianza offerta. L’elemento che risulta più evidente è il lascito teorico, di molto prevalente rispetto a quello progettuale che si è andato mescolando di volta in volta con la tradizione e l’esperienza dei cosiddetti allievi di Aldo Rossi. Negli stessi anni comincia a farsi strada l’importanza del confronto e del dibattito circa i temi architettonici e nel capitolo La fortuna critica della teoria di Aldo Rossi nella Penisola Iberica è stato affrontato proprio questo rinnovato interesse per la teoria che in quegli anni si stava diffondendo. Si è portato avanti lo studio delle pubblicazioni di Gustavo Gili nella Coleccion Arquitectura y Critica che, a partire dalla fine degli anni Sessanta, pubblica e traduce in lingua spagnola i più importanti saggi di architettura, tra i quali La arquitectura de la ciudad di Aldo Rossi, nel 1971, e Comlejidad y contradiccion en arquitectura di Robert Venturi nel 1972. Entrambi fondamentali per il modo di affrontare determinate tematiche di cui sempre più in quegli anni si stava interessando la cultura architettonica iberica, diventando così ¬ testi di riferimento anche nelle scuole. Le tracce dell’influenza di Rossi sulla Penisola Iberica si sono poi ricercate nella rivista “2C. Construccion de la Ciudad” individuata come strumento di espressione di una teoria condivisa. Con la nascita nel 1972 a Barcellona di questa rivista viene portato avanti l’impegno di promuovere la Tendenza, facendo riferimento all’opera e alle idee di Rossi ed altri architetti europei, mirando inoltre al recupero di un ruolo privilegiato dell’architettura catalana. A questo proposito sono emersi due fondamentali aspetti che hanno legittimato l’indagine e lo studio di questa fonte: - la diffusione della cultura architettonica, il controllo ideologico e di informazione operato dal lavoro compiuto dalla rivista; - la documentazione circa i criteri di scelta della redazione a proposito del materiale pubblicato. E’ infatti attraverso le pubblicazioni di “2C. Construccion de la Ciudad” che è stato possibile il ritrovamento delle notizie sulla mostra Arquitectura y razionalismo. Aldo Rossi + 21 arquitectos españoles, che accomuna in un’unica esposizione le opere del maestro e di ventuno giovani allievi che hanno recepito e condiviso la teoria espressa ne “L’architettura della città”. Tale mostra viene poi riproposta nella Sezione Internazionale di Architettura della XV Triennale di Milano, la quale dedica un Padiglione col titolo Barcelona, tres epocas tres propuestas. Dalla disamina dei progetti presentati è emerso un interessante caso di confronto tra le Viviendas para gitanos di César Portela e la Casa Bay di Borgo Ticino di Aldo Rossi, di cui si è occupato l’ultimo paragrafo di questo capitolo. Nel corso degli studi è poi emerso un interessante risvolto della ricerca che, capovolgendone l’oggetto stesso, ne ha approfondito gli aspetti cercando di scavare più in profondità nell’analisi della reciproca influenza tra la cultura iberica e Aldo Rossi, questa parte, sviscerata nell’ultimo capitolo, La Penisola Iberica nel “magazzino della memoria” di Aldo Rossi, ha preso il posto di quello che inizialmente doveva presentarsi come il risvolto progettuale della tesi. Era previsto infatti, al termine dello studio dell’influenza di Aldo Rossi sulla Penisola Iberica, un capitolo che concentrava l’attenzione sulla produzione progettuale. A seguito dell’emergere di un’influenza di carattere prettamente teorica, che ha sicuramente modificato la pratica dal punto di vista delle scelte architettoniche, senza però rendersi esplicita dal punto di vista formale, si è preferito, anche per la difficoltà di individuare un solo esempio rappresentativo di quanto espresso, sostituire quest’ultima parte con lo studio dell’altra faccia della medaglia, ossia l’importanza che a sua volta ha avuto la cultura iberica nella formazione della collezione dei riferimenti di Aldo Rossi. L’articolarsi della tesi in fasi distinte, strettamente connesse tra loro da un filo conduttore, ha reso necessari successivi aggiustamenti nel percorso intrapreso, dettati dall’emergere durante la ricerca di nuovi elementi di indagine. Si è pertanto resa esplicita la ricercata eredità di Aldo Rossi, configurandosi però prevalentemente come un’influenza teorica che ha preso le sfumature del contesto e dell’esperienza personale di chi se ne è fatto ricevente, diventandone così un continuatore attraverso il proprio percorso autonomo o collettivo intrapreso in seguito. Come suggerisce José Charters Monteiro, l’eredità di Rossi può essere letta attraverso tre aspetti su cui si basa la sua lezione: la biografia, la teoria dell’architettura, l’opera. In particolar modo per quanto riguarda la Penisola Iberica si può parlare dell’individuazione di un insegnamento riferito alla seconda categoria, i suoi libri di testo, le sue partecipazioni, le traduzioni. Questo è un lascito che rende possibile la continuazione di un dibattito in merito ai temi della teoria dell’architettura, della sue finalità e delle concrete applicazioni nelle opere, che ha permesso il verificarsi di una apertura mentale che mette in relazione l’architettura con altre discipline umanistiche e scientifiche, dalla politica, alla sociologia, comprendendo l’arte, le città la morfologia, la topografia, mediate e messe in relazione proprio attraverso l’architettura.

Supramolecular functional assemblies with photo or chemical addressability

Supramolecular self-assembly represents a key technology for the spontaneous construction of nanoarchitectures and for the fabrication of materials with enhanced physical and chemical properties. In addition, a significant asset of supramolecular self-assemblies rests on their reversible formation, thanks to the kinetic lability of their non-covalent interactions. This dynamic nature can be exploited for the development of “self-healing” and “smart” materials towards the tuning of their functional properties upon various external factors. One particular intriguing objective in the field is to reach a high level of control over the shape and size of the supramolecular architectures, in order to produce well-defined functional nanostructures by rational design. In this direction, many investigations have been pursued toward the construction of self-assembled objects from numerous low-molecular weight scaffolds, for instance by exploiting multiple directional hydrogen-bonding interactions. In particular, nucleobases have been used as supramolecular synthons as a result of their efficiency to code for non-covalent interaction motifs. Among nucleobases, guanine represents the most versatile one, because of its different H-bond donor and acceptor sites which display self-complementary patterns of interactions. Interestingly, and depending on the environmental conditions, guanosine derivatives can form various types of structures. Most of the supramolecular architectures reported in this Thesis from guanosine derivatives require the presence of a cation which stabilizes, via dipole-ion interactions, the macrocyclic G-quartet that can, in turn, stack in columnar G-quadruplex arrangements. In addition, in absence of cations, guanosine can polymerize via hydrogen bonding to give a variety of supramolecular networks including linear ribbons. This complex supramolecular behavior confers to the guanine-guanine interactions their upper interest among all the homonucleobases studied. They have been subjected to intense investigations in various areas ranging from structural biology and medicinal chemistry – guanine-rich sequences are abundant in telomeric ends of chromosomes and promoter regions of DNA, and are capable of forming G-quartet based structures– to material science and nanotechnology. This Thesis, organized into five Chapters, describes mainly some recent advances in the form and function provided by self-assembly of guanine based systems. More generally, Chapter 4 will focus on the construction of supramolecular self-assemblies whose self-assembling process and self-assembled architectures can be controlled by light as external stimulus. Chapter 1 will describe some of the many recent studies of G-quartets in the general area of nanoscience. Natural G- quadruplexes can be useful motifs to build new structures and biomaterials such as self-assembled nanomachines, biosensors, therapeutic aptamer and catalysts. In Chapters 2-4 it is pointed out the core concept held in this PhD Thesis, i.e. the supramolecular organization of lipophilic guanosine derivatives with photo or chemical addressability. Chapter 2 will mainly focus on the use of cation-templated guanosine derivatives as a potential scaffold for designing functional materials with tailored physical properties, showing a new way to control the bottom-up realization of well-defined nanoarchitectures. In section 2.6.7, the self-assembly properties of compound 28a may be considered an example of open-shell moieties ordered by a supramolecular guanosine architecture showing a new (magnetic) property. Chapter 3 will report on ribbon-like structures, supramolecular architectures formed by guanosine derivatives that may be of interest for the fabrication of molecular nanowires within the framework of future molecular electronic applications. In section 3.4 we investigate the supramolecular polymerizations of derivatives dG 1 and G 30 by light scattering technique and TEM experiments. The obtained data reveal the presence of several levels of organization due to the hierarchical self-assembly of the guanosine units in ribbons that in turn aggregate in fibrillar or lamellar soft structures. The elucidation of these structures furnishes an explanation to the physical behaviour of guanosine units which display organogelator properties. Chapter 4 will describe photoresponsive self-assembling systems. Numerous research examples have demonstrated that the use of photochromic molecules in supramolecular self-assemblies is the most reasonable method to noninvasively manipulate their degree of aggregation and supramolecular architectures. In section 4.4 we report on the photocontrolled self-assembly of modified guanosine nucleobase E-42: by the introduction of a photoactive moiety at C8 it is possible to operate a photocontrol over the self-assembly of the molecule, where the existence of G-quartets can be alternately switched on and off. In section 4.5 we focus on the use of cyclodextrins as photoresponsive host-guest assemblies: αCD–azobenzene conjugates 47-48 (section 4.5.3) are synthesized in order to obtain a photoresponsive system exhibiting a fine photocontrollable degree of aggregation and self-assembled architecture. Finally, Chapter 5 contains the experimental protocols used for the research described in Chapters 2-4.

Biomass Gasification - Process analysis and dimensioning aspects for downdraft units and gas cleaning lines

In such territories where food production is mostly scattered in several small / medium size or even domestic farms, a lot of heterogeneous residues are produced yearly, since farmers usually carry out different activities in their properties. The amount and composition of farm residues, therefore, widely change during year, according to the single production process periodically achieved. Coupling high efficiency micro-cogeneration energy units with easy handling biomass conversion equipments, suitable to treat different materials, would provide many important advantages to the farmers and to the community as well, so that the increase in feedstock flexibility of gasification units is nowadays seen as a further paramount step towards their wide spreading in rural areas and as a real necessity for their utilization at small scale. Two main research topics were thought to be of main concern at this purpose, and they were therefore discussed in this work: the investigation of fuels properties impact on gasification process development and the technical feasibility of small scale gasification units integration with cogeneration systems. According to these two main aspects, the present work was thus divided in two main parts. The first one is focused on the biomass gasification process, that was investigated in its theoretical aspects and then analytically modelled in order to simulate thermo-chemical conversion of different biomass fuels, such as wood (park waste wood and softwood), wheat straw, sewage sludge and refuse derived fuels. The main idea is to correlate the results of reactor design procedures with the physical properties of biomasses and the corresponding working conditions of gasifiers (temperature profile, above all), in order to point out the main differences which prevent the use of the same conversion unit for different materials. At this scope, a gasification kinetic free model was initially developed in Excel sheets, considering different values of air to biomass ratio and the downdraft gasification technology as particular examined application. The differences in syngas production and working conditions (process temperatures, above all) among the considered fuels were tried to be connected to some biomass properties, such elementary composition, ash and water contents. The novelty of this analytical approach was the use of kinetic constants ratio in order to determine oxygen distribution among the different oxidation reactions (regarding volatile matter only) while equilibrium of water gas shift reaction was considered in gasification zone, by which the energy and mass balances involved in the process algorithm were linked together, as well. Moreover, the main advantage of this analytical tool is the easiness by which the input data corresponding to the particular biomass materials can be inserted into the model, so that a rapid evaluation on their own thermo-chemical conversion properties is possible to be obtained, mainly based on their chemical composition A good conformity of the model results with the other literature and experimental data was detected for almost all the considered materials (except for refuse derived fuels, because of their unfitting chemical composition with the model assumptions). Successively, a dimensioning procedure for open core downdraft gasifiers was set up, by the analysis on the fundamental thermo-physical and thermo-chemical mechanisms which are supposed to regulate the main solid conversion steps involved in the gasification process. Gasification units were schematically subdivided in four reaction zones, respectively corresponding to biomass heating, solids drying, pyrolysis and char gasification processes, and the time required for the full development of each of these steps was correlated to the kinetics rates (for pyrolysis and char gasification processes only) and to the heat and mass transfer phenomena from gas to solid phase. On the basis of this analysis and according to the kinetic free model results and biomass physical properties (particles size, above all) it was achieved that for all the considered materials char gasification step is kinetically limited and therefore temperature is the main working parameter controlling this step. Solids drying is mainly regulated by heat transfer from bulk gas to the inner layers of particles and the corresponding time especially depends on particle size. Biomass heating is almost totally achieved by the radiative heat transfer from the hot walls of reactor to the bed of material. For pyrolysis, instead, working temperature, particles size and the same nature of biomass (through its own pyrolysis heat) have all comparable weights on the process development, so that the corresponding time can be differently depending on one of these factors according to the particular fuel is gasified and the particular conditions are established inside the gasifier. The same analysis also led to the estimation of reaction zone volumes for each biomass fuel, so as a comparison among the dimensions of the differently fed gasification units was finally accomplished. Each biomass material showed a different volumes distribution, so that any dimensioned gasification unit does not seem to be suitable for more than one biomass species. Nevertheless, since reactors diameters were found out quite similar for all the examined materials, it could be envisaged to design a single units for all of them by adopting the largest diameter and by combining together the maximum heights of each reaction zone, as they were calculated for the different biomasses. A total height of gasifier as around 2400mm would be obtained in this case. Besides, by arranging air injecting nozzles at different levels along the reactor, gasification zone could be properly set up according to the particular material is in turn gasified. Finally, since gasification and pyrolysis times were found to considerably change according to even short temperature variations, it could be also envisaged to regulate air feeding rate for each gasified material (which process temperatures depend on), so as the available reactor volumes would be suitable for the complete development of solid conversion in each case, without even changing fluid dynamics behaviour of the unit as well as air/biomass ratio in noticeable measure. The second part of this work dealt with the gas cleaning systems to be adopted downstream the gasifiers in order to run high efficiency CHP units (i.e. internal engines and micro-turbines). Especially in the case multi–fuel gasifiers are assumed to be used, weightier gas cleaning lines need to be envisaged in order to reach the standard gas quality degree required to fuel cogeneration units. Indeed, as the more heterogeneous feed to the gasification unit, several contaminant species can simultaneously be present in the exit gas stream and, as a consequence, suitable gas cleaning systems have to be designed. In this work, an overall study on gas cleaning lines assessment is carried out. Differently from the other research efforts carried out in the same field, the main scope is to define general arrangements for gas cleaning lines suitable to remove several contaminants from the gas stream, independently on the feedstock material and the energy plant size The gas contaminant species taken into account in this analysis were: particulate, tars, sulphur (in H2S form), alkali metals, nitrogen (in NH3 form) and acid gases (in HCl form). For each of these species, alternative cleaning devices were designed according to three different plant sizes, respectively corresponding with 8Nm3/h, 125Nm3/h and 350Nm3/h gas flows. Their performances were examined on the basis of their optimal working conditions (efficiency, temperature and pressure drops, above all) and their own consumption of energy and materials. Successively, the designed units were combined together in different overall gas cleaning line arrangements, paths, by following some technical constraints which were mainly determined from the same performance analysis on the cleaning units and from the presumable synergic effects by contaminants on the right working of some of them (filters clogging, catalysts deactivation, etc.). One of the main issues to be stated in paths design accomplishment was the tars removal from the gas stream, preventing filters plugging and/or line pipes clogging At this scope, a catalytic tars cracking unit was envisaged as the only solution to be adopted, and, therefore, a catalytic material which is able to work at relatively low temperatures was chosen. Nevertheless, a rapid drop in tars cracking efficiency was also estimated for this same material, so that an high frequency of catalysts regeneration and a consequent relevant air consumption for this operation were calculated in all of the cases. Other difficulties had to be overcome in the abatement of alkali metals, which condense at temperatures lower than tars, but they also need to be removed in the first sections of gas cleaning line in order to avoid corrosion of materials. In this case a dry scrubber technology was envisaged, by using the same fine particles filter units and by choosing for them corrosion resistant materials, like ceramic ones. Besides these two solutions which seem to be unavoidable in gas cleaning line design, high temperature gas cleaning lines were not possible to be achieved for the two larger plant sizes, as well. Indeed, as the use of temperature control devices was precluded in the adopted design procedure, ammonia partial oxidation units (as the only considered methods for the abatement of ammonia at high temperature) were not suitable for the large scale units, because of the high increase of reactors temperature by the exothermic reactions involved in the process. In spite of these limitations, yet, overall arrangements for each considered plant size were finally designed, so that the possibility to clean the gas up to the required standard degree was technically demonstrated, even in the case several contaminants are simultaneously present in the gas stream. Moreover, all the possible paths defined for the different plant sizes were compared each others on the basis of some defined operational parameters, among which total pressure drops, total energy losses, number of units and secondary materials consumption. On the basis of this analysis, dry gas cleaning methods proved preferable to the ones including water scrubber technology in al of the cases, especially because of the high water consumption provided by water scrubber units in ammonia adsorption process. This result is yet connected to the possibility to use activated carbon units for ammonia removal and Nahcolite adsorber for chloride acid. The very high efficiency of this latter material is also remarkable. Finally, as an estimation of the overall energy loss pertaining the gas cleaning process, the total enthalpy losses estimated for the three plant sizes were compared with the respective gas streams energy contents, these latter obtained on the basis of low heating value of gas only. This overall study on gas cleaning systems is thus proposed as an analytical tool by which different gas cleaning line configurations can be evaluated, according to the particular practical application they are adopted for and the size of cogeneration unit they are connected to.

Modelli Digitali e Archivi di Progetto. Sistemi integrati di documentazione per l'architettura.

Le tecniche dell'informazione e i metodi della comunicazione hanno modificato il modo di redigere documenti destinati a trasmettere la conoscenza, in un processo che è a tutt'oggi in corso di evoluzione. Anche l'attività progettuale in ingegneria ed architettura, pure in un settore caratterizzato da una notevole inerzia metodologica e restio all'innovazione quale è quello dell'industria edilizia, ha conosciuto profonde trasformazioni in ragione delle nuove espressioni tecnologiche. Da tempo l'informazione necessaria per realizzare un edificio, dai disegni che lo rappresentano sino ai documenti che ne indicano le modalità costruttive, può essere gestita in maniera centralizzata mediante un unico archivio di progetto denominato IPDB (Integrated Project DataBase) pur essendone stata recentemente introdotta sul mercato una variante più operativa chiamata BIM (Building Information Modelling). Tuttavia l'industrializzazione del progetto che questi strumenti esplicano non rende conto appieno di tutti gli aspetti che vedono la realizzazione dell'opera architettonica come collettore di conoscenze proprie di una cultura progettuale che, particolarmente in Italia, è radicata nel tempo. La semantica della rappresentazione digitale è volta alla perequazione degli elementi costitutivi del progetto con l'obiettivo di catalogarne le sole caratteristiche fabbricative. L'analisi della letteratura scientifica pertinente alla materia mostra come non sia possibile attribuire ai metodi ed ai software presenti sul mercato la valenza di raccoglitori omnicomprensivi di informazione: questo approccio olistico costituisce invece il fondamento della modellazione integrata intesa come originale processo di rappresentazione della conoscenza, ordinata secondo il paradigma delle "scatole cinesi", modello evolvente che unifica linguaggi appartenenti ai differenti attori compartecipanti nei settori impiantistici, strutturali e della visualizzazione avanzata. Evidenziando criticamente i pregi e i limiti operativi derivanti dalla modellazione integrata, la componente sperimentale della ricerca è stata articolata con l'approfondimento di esperienze condotte in contesti accademici e professionali. Il risultato conseguito ha coniugato le tecniche di rilevamento alle potenzialità di "modelli tridimensionali intelligenti", dotati cioè di criteri discriminanti per la valutazione del relazionamento topologico dei componenti con l'insieme globale.

Design, implementation and evaluation of a virtual laboratory for Computer Engineering Education

Broad consensus has been reached within the Education and Cognitive Psychology research communities on the need to center the learning process on experimentation and concrete application of knowledge, rather than on a bare transfer of notions. Several advantages arise from this educational approach, ranging from the reinforce of students learning, to the increased opportunity for a student to gain greater insight into the studied topics, up to the possibility for learners to acquire practical skills and long-lasting proficiency. This is especially true in Engineering education, where integrating conceptual knowledge and practical skills assumes a strategic importance. In this scenario, learners are called to play a primary role. They are actively involved in the construction of their own knowledge, instead of passively receiving it. As a result, traditional, teacher-centered learning environments should be replaced by novel learner-centered solutions. Information and Communication Technologies enable the development of innovative solutions that provide suitable answers to the need for the availability of experimentation supports in educational context. Virtual Laboratories, Adaptive Web-Based Educational Systems and Computer-Supported Collaborative Learning environments can significantly foster different learner-centered instructional strategies, offering the opportunity to enhance personalization, individualization and cooperation. More specifically, they allow students to explore different kinds of materials, to access and compare several information sources, to face real or realistic problems and to work on authentic and multi-facet case studies. In addition, they encourage cooperation among peers and provide support through coached and scaffolded activities aimed at fostering reflection and meta-cognitive reasoning. This dissertation will guide readers within this research field, presenting both the theoretical and applicative results of a research aimed at designing an open, flexible, learner-centered virtual lab for supporting students in learning Information Security.

Nonlinear / electromagnetic co-simulation and co-design of microwave links in highly polluted and / or strongly inhomogeneous environments

The objective of the Ph.D. thesis is to put the basis of an all-embracing link analysis procedure that may form a general reference scheme for the future state-of-the-art of RF/microwave link design: it is basically meant as a circuit-level simulation of an entire radio link, with – generally multiple – transmitting and receiving antennas examined by EM analysis. In this way the influence of mutual couplings on the frequency-dependent near-field and far-field performance of each element is fully accounted for. The set of transmitters is treated as a unique nonlinear system loaded by the multiport antenna, and is analyzed by nonlinear circuit techniques. In order to establish the connection between transmitters and receivers, the far-fields incident onto the receivers are evaluated by EM analysis and are combined by extending an available Ray Tracing technique to the link study. EM theory is used to describe the receiving array as a linear active multiport network. Link performances in terms of bit error rate (BER) are eventually verified a posteriori by a fast system-level algorithm. In order to validate the proposed approach, four heterogeneous application contexts are provided. A complete MIMO link design in a realistic propagation scenario is meant to constitute the reference case study. The second one regards the design, optimization and testing of various typologies of rectennas for power generation by common RF sources. Finally, the project and implementation of two typologies of radio identification tags, at X-band and V-band respectively. In all the cases the importance of an exhaustive nonlinear/electromagnetic co-simulation and co-design is demonstrated to be essential for any accurate system performance prediction.

Design and fabrication of MOMS-based ultrasonic probes for minimally invasive endoscopic applications

A Micro-opto-mechanical systems (MOMS) based technology for the fabrication of ultrasonic probes on optical fiber is presented. Thanks to the high miniaturization level reached, the realization of an ultrasonic system constituted by ultrasonic generating and detecting elements, suitable for minimally invasive applications or Non Destructive Evaluation (NDE) of materials at high resolution, is demonstrated. The ultrasonic generation is realized by irradiating a highly absorbing carbon film patterned on silicon micromachined structures with a nanosecond pulsed laser source, generating a mechanical shock wave due to the thermal expansion of the film induced by optical energy conversion into heat. The short duration of the pulsed laser, together with an appropriate emitter design, assure high frequency and wide band ultrasonic generation. The acoustic detection is also realized on a MOMS device using an interferometric receiver, fabricated with a Fabry-Perot optical cavity realized by means of a patterned SU-8 and two Al metallization levels. In order to detect the ultrasonic waves, the cavity is interrogated by a laser beam measuring the reflected power with a photodiode. Various issues related to the design and fabrication of these acoustic probes are investigated in this thesis. First, theoretical models are developed to characterize the opto-acoustic behavior of the devices and estimate their expected acoustic performances. Tests structures are realized to derive the relevant physical parameters of the materials constituting the MOMS devices and determine the conditions theoretically assuring the best acoustic emission and detection performances. Moreover, by exploiting the models and the theoretical results, prototypes of acoustic probes are designed and their fabrication process developed by means of an extended experimental activity.

Modeling, design and experimental characterization of Micro-Electro-Mechanical-Systems for gas chromatographic applications

Design parameters, process flows, electro-thermal-fluidic simulations and experimental characterizations of Micro-Electro-Mechanical-Systems (MEMS) suited for gas-chromatographic (GC) applications are presented and thoroughly described in this thesis, whose topic belongs to the research activities the Institute for Microelectronics and Microsystems (IMM)-Bologna is involved since several years, i.e. the development of micro-systems for chemical analysis, based on silicon micro-machining techniques and able to perform analysis of complex gaseous mixtures, especially in the field of environmental monitoring. In this regard, attention has been focused on the development of micro-fabricated devices to be employed in a portable mini-GC system for the analysis of aromatic Volatile Organic Compounds (VOC) like Benzene, Toluene, Ethyl-benzene and Xylene (BTEX), i.e. chemical compounds which can significantly affect environment and human health because of their demonstrated carcinogenicity (benzene) or toxicity (toluene, xylene) even at parts per billion (ppb) concentrations. The most significant results achieved through the laboratory functional characterization of the mini-GC system have been reported, together with in-field analysis results carried out in a station of the Bologna air monitoring network and compared with those provided by a commercial GC system. The development of more advanced prototypes of micro-fabricated devices specifically suited for FAST-GC have been also presented (silicon capillary columns, Ultra-Low-Power (ULP) Metal OXide (MOX) sensor, Thermal Conductivity Detector (TCD)), together with the technological processes for their fabrication. The experimentally demonstrated very high sensitivity of ULP-MOX sensors to VOCs, coupled with the extremely low power consumption, makes the developed ULP-MOX sensor the most performing metal oxide sensor reported up to now in literature, while preliminary test results proved that the developed silicon capillary columns are capable of performances comparable to those of the best fused silica capillary columns. Finally, the development and the validation of a coupled electro-thermal Finite Element Model suited for both steady-state and transient analysis of the micro-devices has been described, and subsequently implemented with a fluidic part to investigate devices behaviour in presence of a gas flowing with certain volumetric flow rates.