Correlazioni tra proprietá reologiche, struttura e processabilitá di blend di LLDPE/LDPE

Polymer blends constitute a valuable way to produce relatively low cost new materials. A still open question concerns the miscibility of polyethylene blends. Deviations from the log-additivity rule of the newtonian viscosity are often taken as a signature of immiscibility of the two components. The aim of this thesis is to characterize the rheological behavior in shear and elongation of five series of LLDPE/LDPE blends whose parent polymers have been chosen with different viscosity and SCB content and length. Synergistic effects have been measured for both zero shear viscosity and melt strength. Both SCB length and viscosity ratio between the components have been found to be key parameters for the miscibility of the pure polymers. In particular the miscibility increases with increasing SCB length and with decreasing the LDPE molecular weight and viscosity. This rheological behavior has significant effects on the processability window of these blends when the uni or biaxial elongational flows are involved. The film blowing is one of the processes for which the synergistic effects above mentioned can be crucial. Small scale experiments of film blowing performed for one of the series of blends has demonstrated that the positive deviation of the melt strength enlarges the processability window. In particular, the bubble stability was found to improve or disappear when the melt strength of the samples increased. The blending of LDPE and LLDPE can even reduce undesired melt flow instability phenomena widening, as a consequence, the processability window in extrusion. One of the series of blends has been characterized by means of capillary rheometry in order to allow a careful morphological analysis of the surface of the extruded polymer jets by means of Scanning Electron Microscopy (SEM) with the aim to detect the very early stages of the small scale melt instabilty at low shear rates (sharksin) and to follow its subsequent evolution as long as the shear rate was increased. With this experimental procedure it was possible to evaluate the shear rate ranges corresponding to different flow regions: smooth extrudate surface (absence of instability), sharkskin (small scale instability produced at the capillary exit), stick-slip transition (instability involving the whole capillary wall) and gross melt fracture (i.e. a large scale "upstream" instability originating from the entrance region of the capillary). A quantitative map was finally worked out using which an assessment of the flow type for a given shear rate and blend composition can be predicted.

Quality and safety of oils and fats obtained as co-products or by-products of the food chain and destined to animal production

The aim of the first part of this thesis was to evaluate the effect of trans fatty acid- (TFA), contaminant, polycyclic aromatic hydrocarbon (PAH)- and oxidation productenriched diets on the content of TFA and conjugated linoleic acid (CLA) isomers in meat and liver of both poultry and rabbit. The enriched feedings were prepared with preselected fatty co-and by-products that contained low and high levels of TFA (low, palm fatty acid distillate; high, hydrogenated palm fatty acid distillate), environmental contaminants (dioxins and PCBs) (two different fish oils), PAH (olive oil acid oils and pomace olive oil from chemical refining, for low and high levels) and oxidation products (sunflower-olive oil blend before and after frying), so as to obtain single feedings with three enrichment degrees (high, medium and low) of the compound of interest. This experimental set-up is a part of a large, collaborative European project (http://www.ub.edu/feedfat/), where other chemical and health parameters are assessed. Lipids were extracted, methylated with diazomethane, then transmethylated with 2N KOH/methanol and analyzed by GC and silver-ion TLC-GC. TFA and CLA were determined in the fats, the feedings, meat and liver of both poultry and rabbit. In general, the level of TFA and CLA in meat and liver mainly varied according to those originally found in the feeding fats. It must be pointed out, though, that TFA and CLA accumulation was different for the two animal species, as well as for the two types of tissues. The TFA composition of meat and liver changes according to the composition of the oils added to the feeds with some differences between species. Chicken meat with skin shows higher TFA content (2.6–5.4 fold) than rabbit meat, except for the “PAH” trial. Chicken liver shows higher TFA content (1.2–2.1 fold) than rabbit liver, except for the “TRANS” and “PAH” trials. In both chicken and rabbit meats, the TFA content was higher for the “TRANS” trial, followed by the “DIOXIN” trial. Slight differences were found on the “OXIDATION” and “PAH” trends in both types of meats. In both chicken and rabbit livers, the TFA content was higher for the “TRANS” trial, followed by those of the “PAH”, “DIOXIN” and “OXIDATION” trials. This trend, however, was not identical to that of feeds, where the TFA content varied as follows: “TRANS” > “DIOXIN” >“PAH” > “OXIDATION”. In chicken and rabbit meat samples, C18:1 TFA were the most abundant, followed by C18:2 TFA and C18:3 TFA, except for the “DIOXIN” trial where C18:3 TFA > C18:2 TFA. In chicken and rabbit liver samples of the “TRANS” and “OXIDATION” trials, C18:1 TFA were the most abundant, followed by C18:2 TFA and C18:3 TFA, whereas C18:3 TFA > C18:2 in the “DIOXIN” trial. Slight differences were found on the “PAH” trend in livers from both species. The second part of the thesis dealt with the study of lipid oxidation in washed turkey muscle added with different antioxidants. The evaluation on the oxidative stability of muscle foods found that oxidation could be measured by headspace solid phase microestraction (SPME) of hexanal and propanal. To make this method effective, an antioxidant system was added to stored muscle to stop the oxidative processes. An increase in ionic strength of the sample was also implemented to increase the concentration of aldehydes in the headspace. This method was found to be more sensitive than the commonly used thiobarbituric acid reactive substances (TBARs) method. However, after antioxidants were added and oxidation was stopped, the concentration of aldehydes decreased. It was found that the decrease in aldehyde concentration was due to the binding of the aldehydes to muscle proteins, thus decreasing the volatility and making them less detectable.

Nuovi catalizzatori per l'idrogenazione, l'idrogenolisi/ring-opening di composti aromatici policiclici

The removal of aromatic hydrocarbons from diesel has received considerable attention after environmental regulations that require petroleum refiners to raise cetane number and to limit aromatics in diesel fuel in order to improve combustion efficiency and reduce particulate and NOx emissions. An alternative is blending with Fischer–Tropsch (FT) gas-to-liquid diesel fuel; however, this option may not be economically viable solution in case of extensive blend. Another alternative is to incorporate in the diesel pool a greater fraction of the so-called light cycle oil (LCO). Due to its high aromatics content and its low cetane number (typically between 20 and 30), the incorporation of LCO may have a negative impact on the quality of diesel. Current technologies for LCO improvement are based on hydrogenation to adjust both sulphur and cetane number but while an important fraction of the aromatics present in LCO can be saturated in a deep hydrogenation process, the cetane number may still be lower than the target values specified in diesel legislations, so further upgrading is needed. An interesting technology for improving the cetane number of diesels and maintaining meanwhile high diesel yields is achieved by combining a complete hydrogenation process with a selective ring opening (SRO) reaction of the naphthenic rings. The SRO can be defined as naphthene ring-opening to form compounds with high cetane number, but without any carbon losses. Controlling the interconversion of six- and five- membered rings via an acid-catalyzed ring-contraction step is also of great importance, since selective conversion of six-membered to five-membered naphthene rings greatly influences ring-opening rates and selectivity. High intrinsic activity may be enhanced by deposition of noble metals on acidic, high surface area supports, because it is possible to arrange close proximity of the metal and acid sites. Moreover, in large-pore supports, the diffusion resistance of liquid reactants into the pores is minimized. In addition to metal centres, the acid sites of support also plays role in aromatics hydrogenation. However, the functions of different kinds of acid sites (Brønsted vs. Lewis acidity), and their optimal concentrations and strengths, remain unclear. In the present study we investigated the upgrading of an aromatic-rich feedstock over different type of metal supported on mesoporous silica-alumina. The selective hydrogenolysis and ring opening of tetrahydronaphthalene (THN or tetralin) was carried out as representative of LCO fractions after deep hydrogenation process. In this regards the aim of this study is to evaluate both the effect of metals and that of the supports characterized by different acid distribution and strength, on conversion and selectivity. For this purpose a series of catalysts were prepared by impregnation. The catalysts were characterized and conversion tests of THN were performed in a lab-scale plant operating in the pressure range from 7.0-5.0 MPa and in the temperature range from 300 to 360°C.

Mass transport in polymers

The study of mass transport in polymeric membranes has grown in importance due to its potential application in many processes such as separation of gases and vapors, packaging, controlled drug release. The diffusion of a low molecular weight species in a polymer is often accompanied by other phenomena like swelling, reactions, stresses, that have not been investigated in all their aspects yet. Furthermore, novel materials have been developed that include inorganic fillers, reactive functional groups or ions, that make the scenery even more complicated. The present work focused on the experimental study of systems where the diffusion is accompanied by other processes; suitable models were also developed to describe the particular circumstances in order to understand the underlying concepts and be able to design the performances of the material. The effect of solvent-induced deformation in polymeric films during sorption processes was studied since the dilation, especially in constrained membranes, can cause the development of stresses and therefore early failures of the material. The bending beam technique was used to test the effects of the dilation and the stress induced in the polymer by penetrant diffusion. A model based on the laminate theory was developed that accounts for the swelling and is able to predict the stress that raise in the material. The addition of inorganic fillers affects the transport properties of polymeric films. Mixed matrix membranes based on fluorinated, high free volume matrices show attractive performances for separation purposes but there is a need for deeper investigation of the selectivity properties towards gases and vapors. A new procedure based on the NELF model was tested on the experimental data; it allows to predict solubility of every penetrant on the basis of data for one vapor. The method has proved to be useful also for the determination of the diffusion coefficient and for an estimation of the permeability in the composite materials. Oxygen scavenging systems can overcome lack of barrier properties in common polymers that forbids their application in sensitive applications as food packaging. The final goal of obtaining a membrane almost impermeable to oxygen leads to experimental times out of reach. Hence, a simple model was developed in order to describe the transport of oxygen in a membrane with also reactive groups and analyze the experimental data collected on SBS copolymers that show attractive scavenging capacity. Furthermore, a model for predicting the oxygen barrier behavior of a film formed as a blend of OSP in a common packaging material was built, considering particles capable of reactions with oxygen embedded in a non-reactive matrix. Perfluorosulphonic acid ionomers (PFSI) are capturing attention due to a high thermal and chemical resistance coupled with very peculiar transport properties, that make them appropriate to be used in fuel cells. The possible effect of different formation procedure was studied together with the swelling due to water sorption since both water uptake and dilation can dramatically affect the fuel cells performances. The water diffusion and sorption was studied with a FTIR-ATR spectrometer that can give deeper information on the bonds between water molecules and the sulphonic hydrophilic groups and, therefore, on the microstructure of the hydrated ionomer.

Letteratura postmoderna e comunicazione pubblicitaria, problemi teorici e analisi testuali

Premise: In the literary works of our anthropological and cultural imagination, the various languages and the different discursive practices are not necessarily quoted, expressly alluded to or declared through clear expressive mechanisms; instead, they rather constitute a substratum, a background, now consolidated, which with irony and intertextuality shines through the thematic and formal elements of each text. The various contaminations, hybridizations and promptings that we find in the expressive forms, the rhetorical procedures and the linguistic and thematic choices of post-modern literary texts are shaped as fluid and familiar categories. Exchanges and passages are no longer only allowed but also inevitable; the post-modern imagination is made up of an agglomeration of discourses that are no longer really separable, built up from texts that blend and quote one another, composing, each with its own specificities, the great family of the cultural products of our social scenario. A literary work, therefore, is not only a whole phenomenon, delimited hic et nunc by a beginning and an ending, but is a fragment of that complex, dense and boundless network that is given by the continual interrelations between human forms of communication and symbolization. The research hypothesis: A vision is delineated of comparative literature as a discipline attentive to the social contexts in which texts take shape and move and to the media-type consistency that literary phenomena inevitably take on. Hence literature is seen as an open systematicity that chooses to be contaminated by other languages and other discursive practices of an imagination that is more than ever polymorphic and irregular. Inside this interpretative framework the aim is to focus the analysis on the relationship that postmodern literature establishes with advertising discourse. On one side post-modern literature is inserted in the world of communication, loudly asserting the blending and reciprocal contamination of literary modes with media ones, absorbing their languages and signification practices, translating them now into thematic nuclei, motifs and sub-motifs and now into formal expedients and new narrative choices; on the other side advertising is chosen as a signification practice of the media universe, which since the 1960s has actively contributed to shaping the dynamics of our socio-cultural scenarios, in terms which are just as important as those of other discursive practices. Advertising has always been a form of communication and symbolization that draws on the collective imagination – myths, actors and values – turning them into specific narrative programs for its own texts. Hence the aim is to interpret and analyze this relationship both from a strictly thematic perspective – and therefore trying to understand what literature speaks about when it speaks about advertising, and seeking advertising quotations in post-modern fiction – and from a formal perspective, with a search for parallels and discordances between the rhetorical procedures, the languages and the verifiable stylistic choices in the texts of the two different signification practices. The analysis method chosen, for the purpose of constructive multiplication of the perspectives, aims to approach the analytical processes of semiotics, applying, when possible, the instruments of the latter, in order to highlight the thematic and formal relationships between literature and advertising. The corpus: The corpus of the literary texts is made up of various novels and, although attention is focused on the post-modern period, there will also be ineludible quotations from essential authors that with their works prompted various reflections: H. De Balzac, Zola, Fitzgerald, Joyce, Calvino, etc… However, the analysis focuses the corpus on three authors: Don DeLillo, Martin Amis and Aldo Nove, and in particular the followings novels: “Americana” (1971) and “Underworld” (1999) by Don DeLillo, “Money” (1984) by Martin Amis and “Woobinda and other stories without a happy ending” (1996) and “Superwoobinda” (1998) by Aldo Nove. The corpus selection is restricted to these novels for two fundamental reasons: 1. assuming parameters of spatio-temporal evaluation, the texts are representative of different socio-cultural contexts and collective imaginations (from the masterly glimpses of American life by DeLillo, to the examples of contemporary Italian life by Nove, down to the English imagination of Amis) and of different historical moments (the 1970s of DeLillo’s Americana, the 1980s of Amis, down to the 1990s of Nove, decades often used as criteria of division of postmodernism into phases); 2. adopting a perspective of strictly thematic analysis, as mentioned in the research hypothesis, the variations and the constants in the novels (thematic nuclei, topoi, images and narrative developments) frequently speak of advertising and inside the narrative plot they affirm various expressions and realizations of it: value ones, thematic ones, textual ones, urban ones, etc… In these novels the themes and the processes of signification of advertising discourse pervade time, space and the relationships that the narrator character builds around him. We are looking at “particle-characters” whose endless facets attest the influence and contamination of advertising in a large part of the narrative developments of the plot: on everyday life, on the processes of acquisition and encoding of the reality, on ideological and cultural baggage, on the relationships and interchanges with the other characters, etc… Often the characters are victims of the implacable consequentiality of the advertising mechanism, since the latter gets the upper hand over the usual processes of communication, which are overwhelmed by it, wittingly or unwittingly (for example: disturbing openings in which the protagonist kills his or her parents on the basis of a spot, former advertisers that live life codifying it through the commercial mechanisms of products, sons and daughters of advertisers that as children instead of playing outside for whole nights saw tapes of spots.) Hence the analysis arises from the text and aims to show how much the developments and the narrative plots of the novels encode, elaborate and recount the myths, the values and the narrative programs of advertising discourse, transforming them into novel components in their own right. And also starting from the text a socio-cultural reference context is delineated, a collective imagination that is different, now geographically, now historically, and from comparison between them the aim is to deduce the constants, the similarities and the variations in the relationship between literature and advertising.

Functional components and lipid quality assessment in vegetable foods: analytical and technological approaches

Lipids are important components that contribute very significantly to nutritional and technological quality of foods because they are the least stable macro-components in foods, due to high susceptibility to oxidation. When rancidity take place, it makes food unhealthy and unacceptable for consumers. Thus, the presence of antioxidants, naturally present of added to foods, is required to enhance shelf life of foods. Moreover, antioxidant like phenolic compounds play an important role in human health enhancing the functionality of foods. The aim of this PhD project was the study of lipid quality and lipid oxidation in different vegetable foods focusing on analytical and technological aspects in order to figure out the effects of lipid composition and bioactive compounds (phenolic compounds, omega-3 fatty acids and dietary fiber) addition on their shelf life. In addition, bioavailability and antioxidant effects of phenolic compounds in human and animals, respectively, were evaluated after consumption of vegetable foods. The first section of the work was focused on the evaluation of lipid quality impact on technological behaviour of vegetable foods. Because of that, cocoa butter with different melting point were evaluated by chromatographic techniques (GC, TLC) and the sample with the higher melting point showed the presence of fatty acids, triglycerides, 2-monoglycerides and FT-IR profile different from genuine cocoa butter, meaning an adding of foreign fat (lauric-fat) not allowed by the law. Looking at lipid quality of other vegetable foods, an accelerated shelf life test (OXITEST®), was used to evaluate of lipid stability to oxidation in tarallini snacks made up using different lipid matrices (sunflower oil, extravirgin olive oil and a blend of extravirgin olive oil and lard). The results showed a good ability of OXITEST® to discriminate between lipid unsaturation and different cooking times, without any samples fat extraction. In the second section, the role of bioactive compounds on cereal based food shelf life was studied in different bakeries by GC, spectrophotometric methods and capillary electrophoresis. It was examined the relationships between phenolic compounds, added with flour, and lipid oxidation of tarallini and frollini. Both products showed an increase in lipid oxidation during storage and antioxidant effects on lipid oxidation were not as expected. Furthermore, the influence of enrichment in polyunsaturated fatty acids on lipid oxidation of pasta was evaluated. The results proved that LC n-3 PUFA were not significantly implicated in the onset of oxidation in spaghetti stored under daylight and accelerated oxidation in a laboratory heater. The importance of phenolic compounds as antioxidant in humans and rats was also studied, by HPLC/MS in the latter section. For this purpose, apigenin and apigenin glycosides excretion was investigated in six women’s urine in a 24 hours study. After a single dose of steamed artichokes, both aglicone and glucuronide metabolites were recovered in 24 h urine. Moreover, the effect of whole grain durum wheat bread and whole grain Kamut® khorasan bread in rats were evaluated. Both cereals were good sources of antioxidants but Kamut® bread fed animals had a better response to stress than wheat durum fed, especially when a sourdough bread was supplied.

Trattamenti termici: valutazione delle degradazioni termossidative di oli da frittura e determinazione di composti aromatici in matrici alimentari complesse

Lo studio condotto durante il Dottorato di Ricerca è stato focalizzato sulla valutazione e sul monitoraggio delle diverse degradazioni termossidative in oli da frittura. Per raggiungere tale obiettivo si è ritenuto opportuno procedere mediante uno screening dei principali oli presenti sul mercato italiano e successiva messa a punto di due miscele di oli vegetali che sono state sottoposte a due piani sperimentali di frittura controllata e standardizzata in laboratorio, seguiti da due piani di frittura eseguiti in due differenti situazioni reali quali mensa e ristorante. Ognuna delle due miscele è stata messa a confronto con due oli di riferimento. A tal fine è stata identificato il profilo in acidi grassi, la stabilità ossidativa ed idrolitica, il punto di fumo, i composti polari, il contenuto in tocoferoli totali, ed i composti volatili sia sugli oli crudi che sottoposti ai diversi processi di frittura. Lo studio condotto ha permesso di identificare una delle miscele ideate come valida alternativa all’impiego dell’olio di palma ampiamente utilizzato nelle fritture degli alimenti, oltre a fornire delle indicazioni più precise sulla tipologia e sull’entità delle modificazioni che avvengono in frittura, a seconda delle condizioni impiegate.

Conductive Polymer Composites

In recent years, nanotechnologies have led to the production of materials with new and sometimes unexpected qualities through the manipulation of nanoscale components. This research aimed primarily to the study of the correlation between hierarchical structures of hybrid organic-inorganic materials such as conductive polymer composites (CPCs). Using a bottom-up methodology, we could synthesize a wide range of inorganic nanometric materials with a high degree of homogeneity and purity, such as thiol capped metal nanoparticles, stoichiometric geomimetic chrysotile nanotubes and metal dioxide nanoparticles. It was also possible to produce inorganic systems formed from the interaction between the synthesized materials. These synthesized materials and others like multiwalled carbon nanotubes and grapheme oxide were used to produce conductive polymer composites. Electrospinning causes polymer fibers to become elongated using an electric field. This technique was used to produce fibers with a nanometric diameter of a polymer blend based on two different intrinsically conducting polymers polymers (ICPs): polyaniline (PANI) and poly(3-hexylthiophene) (P3HT). Using different materials as second phase in the initial electrospun polymer fibers caused significant changes to the material hierarchical structure, leading to the creation of CPCs with modified electrical properties. Further study of the properties of these new materials resulted in a better understanding of the electrical conductivity mechanisms in these electrospun materials.

Studio dei semiochimici coinvolti nelle interazioni intra- e inter-specifiche in Gonocerus acuteangulatus (Goeze) (Heteroptera: Coreidae) in vista di un loro impiego nella difesa del nocciolo.

Gonocerus acuteangulatus (Hemiptera: Coreidae) è considerato uno dei principali fitofagi del nocciolo, in grado di causare con l’attività trofica pesanti perdite quali-quantitative di produzione. Nel triennio sono state quindi condotte indagini sulla bioetologia di G. acuteangulatus volte a: I) studiare comportamento alimentare ed effetti sulla produzione corilicola, II) identificare i feromoni e valutarne l’attività mediante biosaggi fisiologici e comportamentali in laboratorio, semi-campo e campo, III) rilevare le piante ospiti alternative al nocciolo. Mediante isolamento di adulti del coreide su rami di nocciolo con frutti è stata confermata l’assenza di correlazione fra entità del danno e numerosità degli individui presenti in corileto. Dalle analisi sensoriali su nocciole sane e danneggiate è emerso che le alterazioni causate delle punture di nutrizione sono rese più evidenti da conservazione e tostatura. Variazioni di tempi e temperature di tostatura potrebbero mitigare gli effetti del cimiciato. Nello studio dei feromoni, G. acuteangulatus, molto mobile nell’ambiente, è risultato poco adatto ai biosaggi in condizioni artificiali, come quelle in olfattometro e semi-campo. Le femmine sono tuttavia apparse attrattive per adulti di entrambi i sessi, mentre la miscela feromonale sintetizzata ha mostrato un’azione attrattiva, seppure non costante. Pertanto, ulteriori ripetizioni sono necessarie per convalidare questi risultati preliminari, modificando le condizioni di saggio in relazione alle caratteristiche della specie. Infine è stata accertata la preferenza del fitofago per alcune specie vegetali rispetto al nocciolo. Nel corso del triennio, popolazioni molto consistenti di G. acuteangulatus sono state rilevate su bosso, ciliegio di Santa Lucia, rosa selvatica, sanguinello, spino cervino, in corrispondenza del periodo di comparsa e maturazione dei frutti. Nell’impostazione di una strategia di difesa a basso impatto ambientale, l’attrattività di queste piante, in sinergia con eventuali feromoni di aggregazione, potrebbe essere utilmente sfruttata, per mantenere il coreide lontano dalla coltura.

Polimeri tiofenici funzionali e loro applicazioni nel fotovoltaico

Recentemente, sempre più attenzione è stata rivolta all' utilizzo di coloranti organici come assorbitori di luce per la preparazione di strati fotoattivi in celle solari organiche (OPV). I coloranti organici presentano un'elevata abilità nella cattura della luce solare grazie all'elevato coefficiente di estinzione molare e buone proprietà fotofisiche. Per questi motivi sono eccellenti candidati per l'incremento della conversione fotoelettrica in OPV. In questa tesi viene descritta una nuova strategia per l'incorporazione di derivati porfirinici in catena laterale a copolimeri tiofenici. Gli studi svolti hanno dimostrato che poli(3-bromoesil)tiofene può essere variamente funzionalizzato con idrossitetrafenilporfirina (TPPOH), per l'ottenimento di copolimeri utilizzabili come materiali p-donatori nella realizzazione di OPV. I copolimeri poli[3-(6-bromoesil)tiofene-co-(3-[5-(4-fenossi)-10,15,20-trifenilporfirinil]esil tiofene] P[T6Br-co-T6TPP] contenenti differenti quantità di porfirina, sono stati sintetizzati sia con metodi non regiospecifici che regiospecifici, con lo scopo di confrontarene le proprietà e di verificare se la strutture macromolecolare che presenta una regiochimica di sostituzione sempre uguale, promuove o meno il trasporto della carica elettrica, migliorando di conseguenza l'efficienza. E' stato inoltre effettuato un ulteriore confronto tra questi derivati e derivati simili P[T6H-co-T6TPP] che non contengono l'atomo di bromo in catena laterale con lo scopo di verificare se l'assenza del gruppo reattivo, migliora o meno la stabilità termica e chimica dei film polimerici, agendo favorevolmete sulle performance dei dispositivi fotovoltaici. Tutti i copolimeri sono stati caratterizzati con differenti tecniche: spettroscopia NMR, FT-IR e UV-Vis, analisi termiche DSC e TGA, e GPC. Le celle solari Bulk Heterojunction, preparate utilizzando PCBM come materiale elettron-accettore e i copolimeri come materilai elettron-donatori, sono state testate utilizzando un multimetro Keithley e il Solar Simulator.

Charge transport properties of organic conjugated polymers for photovoltaic applications

Charge transport in conjugated polymers as well as in bulk-heterojunction (BHJ) solar cells made of blends between conjugated polymers, as electron-donors (D), and fullerenes, as electron-acceptors (A), has been investigated. It is shown how charge carrier mobility of a series of anthracene-containing poly(p-phenylene-ethynylene)-alt-poly(p-phenylene-vinylene)s (AnE-PVs) is highly dependent on the lateral chain of the polymers, on a moderate variation of the macromolecular parameters (molecular weight and polydispersity), and on the processing conditions of the films. For the first time, the good ambipolar transport properties of this relevant class of conjugated polymers have been demonstrated, consistent with the high delocalization of both the frontier molecular orbitals. Charge transport is one of the key parameters in the operation of BHJ solar cells and depends both on charge carrier mobility in pristine materials and on the nanoscale morphology of the D/A blend, as proved by the results here reported. A straight correlation between hole mobility in pristine AnE-PVs and the fill factor of the related solar cells has been found. The great impact of charge transport for the performance of BHJ solar cells is clearly demonstrated by the results obtained on BHJ solar cells made of neat-C70, instead of the common soluble fullerene derivatives (PCBM or PC70BM). The investigation of neat-C70 solar cells was motivated by the extremely low cost of non-functionalized fullerenes, compared with that of their soluble derivatives (about one-tenth). For these cells, an improper morphology of the blend leads to a deterioration of charge carrier mobility, which, in turn, increases charge carrier recombination. Thanks to the appropriate choice of the donor component, solar cells made of neat-C70 exhibiting an efficiency of 4.22% have been realized, with an efficiency loss of just 12% with respect to the counterpart made with costly PC70BM.