Quality and safety of oils and fats obtained as co-products or by-products of the food chain and destined to animal production

The aim of the first part of this thesis was to evaluate the effect of trans fatty acid- (TFA), contaminant, polycyclic aromatic hydrocarbon (PAH)- and oxidation productenriched diets on the content of TFA and conjugated linoleic acid (CLA) isomers in meat and liver of both poultry and rabbit. The enriched feedings were prepared with preselected fatty co-and by-products that contained low and high levels of TFA (low, palm fatty acid distillate; high, hydrogenated palm fatty acid distillate), environmental contaminants (dioxins and PCBs) (two different fish oils), PAH (olive oil acid oils and pomace olive oil from chemical refining, for low and high levels) and oxidation products (sunflower-olive oil blend before and after frying), so as to obtain single feedings with three enrichment degrees (high, medium and low) of the compound of interest. This experimental set-up is a part of a large, collaborative European project (http://www.ub.edu/feedfat/), where other chemical and health parameters are assessed. Lipids were extracted, methylated with diazomethane, then transmethylated with 2N KOH/methanol and analyzed by GC and silver-ion TLC-GC. TFA and CLA were determined in the fats, the feedings, meat and liver of both poultry and rabbit. In general, the level of TFA and CLA in meat and liver mainly varied according to those originally found in the feeding fats. It must be pointed out, though, that TFA and CLA accumulation was different for the two animal species, as well as for the two types of tissues. The TFA composition of meat and liver changes according to the composition of the oils added to the feeds with some differences between species. Chicken meat with skin shows higher TFA content (2.6–5.4 fold) than rabbit meat, except for the “PAH” trial. Chicken liver shows higher TFA content (1.2–2.1 fold) than rabbit liver, except for the “TRANS” and “PAH” trials. In both chicken and rabbit meats, the TFA content was higher for the “TRANS” trial, followed by the “DIOXIN” trial. Slight differences were found on the “OXIDATION” and “PAH” trends in both types of meats. In both chicken and rabbit livers, the TFA content was higher for the “TRANS” trial, followed by those of the “PAH”, “DIOXIN” and “OXIDATION” trials. This trend, however, was not identical to that of feeds, where the TFA content varied as follows: “TRANS” > “DIOXIN” >“PAH” > “OXIDATION”. In chicken and rabbit meat samples, C18:1 TFA were the most abundant, followed by C18:2 TFA and C18:3 TFA, except for the “DIOXIN” trial where C18:3 TFA > C18:2 TFA. In chicken and rabbit liver samples of the “TRANS” and “OXIDATION” trials, C18:1 TFA were the most abundant, followed by C18:2 TFA and C18:3 TFA, whereas C18:3 TFA > C18:2 in the “DIOXIN” trial. Slight differences were found on the “PAH” trend in livers from both species. The second part of the thesis dealt with the study of lipid oxidation in washed turkey muscle added with different antioxidants. The evaluation on the oxidative stability of muscle foods found that oxidation could be measured by headspace solid phase microestraction (SPME) of hexanal and propanal. To make this method effective, an antioxidant system was added to stored muscle to stop the oxidative processes. An increase in ionic strength of the sample was also implemented to increase the concentration of aldehydes in the headspace. This method was found to be more sensitive than the commonly used thiobarbituric acid reactive substances (TBARs) method. However, after antioxidants were added and oxidation was stopped, the concentration of aldehydes decreased. It was found that the decrease in aldehyde concentration was due to the binding of the aldehydes to muscle proteins, thus decreasing the volatility and making them less detectable.

The impact of swine welfare on some qualitative traits of meat and long cured animal derived products

The present dissertation collects the results of three different research trials which have the common aim to understand the effects of swine welfare (both at farm level and during transport) on the main fresh and dry-cured meat characteristics. The first trial was carried out in order to compare the effects of illumination regimes differing in light duration or light intensity on meat and ham quality of Italian heavy pigs. The results of this trial support the conclusion that, within a moderate range of light intensity and given an appropriate dark period for animal rest, an increase of light duration or intensity above the minimum mandatory levels has no negative impact on carcass composition, meat or long-cured hams quality. The second trial was designed with the aim to investigate the effects of water restriction on growth traits, animal welfare and meat and ham quality of liquid-fed heavy pigs. Overall, the parameters analyzed as concerns growth rate, behavioural traits, blood, as well as carcass, fresh meat and cured hams quality were not affected by the absence of fresh drinking water. However, since liquid feeding did not suppress drinker use or drinker manipulation in the experimental groups, water restriction does not appear to be an applicable method to obtain a reduction of water waste. The third trial, which was carried out in Canada, tested the effectiveness of water sprinkling market-weight pigs (115±10Kg BW) before and after transport in reducing the heat stress experienced under commercial transport conditions. Our results show that the water sprinkling protocol proposed may reduce heat stress during transport and improve pork quality, particularly in specific trailer compartments. This body of research supports the general conclusion that swine welfare could be improved in different scenarios through simple and cost-effective means, without negatively affecting the quality of the main animal-derived products.

Development of instrumental and sensory analytical methods of food obtained by traditional and emerging technologies

The consumer demand for natural, minimally processed, fresh like and functional food has lead to an increasing interest in emerging technologies. The aim of this PhD project was to study three innovative food processing technologies currently used in the food sector. Ultrasound-assisted freezing, vacuum impregnation and pulsed electric field have been investigated through laboratory scale systems and semi-industrial pilot plants. Furthermore, analytical and sensory techniques have been developed to evaluate the quality of food and vegetable matrix obtained by traditional and emerging processes. Ultrasound was found to be a valuable technique to improve the freezing process of potatoes, anticipating the beginning of the nucleation process, mainly when applied during the supercooling phase. A study of the effects of pulsed electric fields on phenol and enzymatic profile of melon juice has been realized and the statistical treatment of data was carried out through a response surface method. Next, flavour enrichment of apple sticks has been realized applying different techniques, as atmospheric, vacuum, ultrasound technologies and their combinations. The second section of the thesis deals with the development of analytical methods for the discrimination and quantification of phenol compounds in vegetable matrix, as chestnut bark extracts and olive mill waste water. The management of waste disposal in mill sector has been approached with the aim of reducing the amount of waste, and at the same time recovering valuable by-products, to be used in different industrial sectors. Finally, the sensory analysis of boiled potatoes has been carried out through the development of a quantitative descriptive procedure for the study of Italian and Mexican potato varieties. An update on flavour development in fresh and cooked potatoes has been realized and a sensory glossary, including general and specific definitions related to organic products, used in the European project Ecropolis, has been drafted.

Ricerca di contaminanti in tessuti animali e in alimenti destinati all'uomo.

La contaminazione chimica rappresenta uno dei rischi principali per la sicurezza alimentare e può arrecare anche gravi danni alla salute umana. Rientrano in questa tesi di dottorato tre famiglie di contaminanti: Micotossine, Metalli e Insetticidi. La ricerca di aflatossina B1 è stata effettuata su 90 confezioni di farina, sia biologici sia convenzionali. La presenza della micotossina è stata rilevata solo nelle farine di mais. Solo un campione di produzione convenzionale ha superato il limite di 2 ppb definito per legge. Il dato di maggior rilievo è stato che il quantitativo di 5 grammi di campionamento si è dimostrato non rappresentativo sul totale della confezione commerciale di farina. Più attendibile si è invece dimostrato un campionamento di 20 grammi. L’aflatossina M1 è stata ricercata in 58 campioni di latte di cui 35 sono risultati positivi. Tuttavia, i livelli riscontrati erano costantemente inferiori al limite previsto per legge. Sono stati sottoposti a estrazione e purificazione, e analizzati con metodica HPLC-FL per la ricerca di Ocratossina A, 114 campioni di bile, 35 campioni di plasma, 40 campioni di rene prelevati da polli in Giordania. Le analisi hanno fornito risultati costantemente negativi. Sono stati analizzati 72 campioni (30 di muscolo, 29 di fegato e 13 di rene) prelevati da 30 bovini nel macello di Irbid (Giordania), di età compresa tra 8 e 30 mesi e provenienti da allevamenti diversi, per la ricerca di 13 elementi essenziali e non essenziali. In questo studio nessun campione supera i livelli massimi stabiliti dalla normativa europea per quanto riguarda gli elementi considerati. Infine, sono stati analizzati 37 campioni di latte ovino e 31 campioni di latte bovino, prelevati in Giordania in diversi allevamenti, per la ricerca di 4 neonicotinoidi (imidacloprid, acetamiprid, thiamethoxam e thiacloprid). I campioni, analizzati con sistema HPLC/MS/MS, sono risultati costantemente negativi ai quattro neonicotinoidi ricercati.

La città di Bologna e la sua storia: diffusione e condivisione delle conoscenze attraverso Webgis open source e Web Mapping

To understand a city and its urban structure it is necessary to study its history. This is feasible through GIS (Geographical Information Systems) and its by-products on the web. Starting from a cartographic view they allow an initial understanding of, and a comparison between, present and past data together with an easy and intuitive access to database information. The research done led to the creation of a GIS for the city of Bologna. It is based on varied data such as historical map, vector and alphanumeric historical data, etc.. After providing information about GIS we thought of spreading and sharing the collected data on the Web after studying two solutions available on the market: Web Mapping and WebGIS. In this study we discuss the stages, beginning with the development of Historical GIS of Bologna, which led to the making of a WebGIS Open Source (MapServer and Chameleon) and the Web Mapping services (Google Earth, Google Maps and OpenLayers).

Biomasse e loro quantificazione economica per un efficiente uso dell'energia

Biomasses and their possible use as energy resource are of great interest today, and the general problem of energy resources as well. In the present study the key questions of the convenience, from both energy and economy standpoints, have been addressed without any bias: the problem has been handled starting from “philosophical” bases disregarding any pre-settled ideology or political trend, but simply using mathematical approaches as logical tools for defining balances in a right way. In this context quantitative indexes such as LCA and EROEI have been widely used, together with multicriteria methods (such as ELECTRE) as decision supporting tools. This approach permits to remove mythologies, such as the unrealistic concept of clean energy, or the strange idea of biomasses as a magic to solve every thing in the field of the energy. As a consequence the present study aims to find any relevant aspect potentially useful for the society, looking at any possible source of energy without prejudices but without unrealistic expectations too. For what concerns biomasses, we studied in great details four very different cases of study, in order to have a scenario as various as much we can. A relevant result is the need to use biomasses together with other more efficient sources, especially recovering by-products from silviculture activities: but attention should be paid to the transportation and environmental costs. Another relevant result is the very difficult possibility of reliable evaluation of dedicated cultures as sources for “biomasses for energy”: the problem has to be carefully evaluated case-by-case, because what seems useful in a context, becomes totally disruptive in another one. In any case the concept itself of convenience is not well defined at a level of macrosystem: it seems more appropriate to limit this very concept at a level of microsystem, considering that what sounds fine in a limited well defined microsystem may cause great damage in another slightly different, or even very similar, microsystem. This approach seems the right way to solve the controversy about the concept of convenience.

Catalytic liquid- and gas-phase oxidations for the synthesis of intermediates and specialty chemicals: some examples of industrial relevance

Nowadays, it is clear that the target of creating a sustainable future for the next generations requires to re-think the industrial application of chemistry. It is also evident that more sustainable chemical processes may be economically convenient, in comparison with the conventional ones, because fewer by-products means lower costs for raw materials, for separation and for disposal treatments; but also it implies an increase of productivity and, as a consequence, smaller reactors can be used. In addition, an indirect gain could derive from the better public image of the company, marketing sustainable products or processes. In this context, oxidation reactions play a major role, being the tool for the production of huge quantities of chemical intermediates and specialties. Potentially, the impact of these productions on the environment could have been much worse than it is, if a continuous efforts hadn’t been spent to improve the technologies employed. Substantial technological innovations have driven the development of new catalytic systems, the improvement of reactions and process technologies, contributing to move the chemical industry in the direction of a more sustainable and ecological approach. The roadmap for the application of these concepts includes new synthetic strategies, alternative reactants, catalysts heterogenisation and innovative reactor configurations and process design. Actually, in order to implement all these ideas into real projects, the development of more efficient reactions is one primary target. Yield, selectivity and space-time yield are the right metrics for evaluating the reaction efficiency. In the case of catalytic selective oxidation, the control of selectivity has always been the principal issue, because the formation of total oxidation products (carbon oxides) is thermodynamically more favoured than the formation of the desired, partially oxidized compound. As a matter of fact, only in few oxidation reactions a total, or close to total, conversion is achieved, and usually the selectivity is limited by the formation of by-products or co-products, that often implies unfavourable process economics; moreover, sometimes the cost of the oxidant further penalizes the process. During my PhD work, I have investigated four reactions that are emblematic of the new approaches used in the chemical industry. In the Part A of my thesis, a new process aimed at a more sustainable production of menadione (vitamin K3) is described. The “greener” approach includes the use of hydrogen peroxide in place of chromate (from a stoichiometric oxidation to a catalytic oxidation), also avoiding the production of dangerous waste. Moreover, I have studied the possibility of using an heterogeneous catalytic system, able to efficiently activate hydrogen peroxide. Indeed, the overall process would be carried out in two different steps: the first is the methylation of 1-naphthol with methanol to yield 2-methyl-1-naphthol, the second one is the oxidation of the latter compound to menadione. The catalyst for this latter step, the reaction object of my investigation, consists of Nb2O5-SiO2 prepared with the sol-gel technique. The catalytic tests were first carried out under conditions that simulate the in-situ generation of hydrogen peroxide, that means using a low concentration of the oxidant. Then, experiments were carried out using higher hydrogen peroxide concentration. The study of the reaction mechanism was fundamental to get indications about the best operative conditions, and improve the selectivity to menadione. In the Part B, I explored the direct oxidation of benzene to phenol with hydrogen peroxide. The industrial process for phenol is the oxidation of cumene with oxygen, that also co-produces acetone. This can be considered a case of how economics could drive the sustainability issue; in fact, the new process allowing to obtain directly phenol, besides avoiding the co-production of acetone (a burden for phenol, because the market requirements for the two products are quite different), might be economically convenient with respect to the conventional process, if a high selectivity to phenol were obtained. Titanium silicalite-1 (TS-1) is the catalyst chosen for this reaction. Comparing the reactivity results obtained with some TS-1 samples having different chemical-physical properties, and analyzing in detail the effect of the more important reaction parameters, we could formulate some hypothesis concerning the reaction network and mechanism. Part C of my thesis deals with the hydroxylation of phenol to hydroquinone and catechol. This reaction is already industrially applied but, for economical reason, an improvement of the selectivity to the para di-hydroxilated compound and a decrease of the selectivity to the ortho isomer would be desirable. Also in this case, the catalyst used was the TS-1. The aim of my research was to find out a method to control the selectivity ratio between the two isomers, and finally to make the industrial process more flexible, in order to adapt the process performance in function of fluctuations of the market requirements. The reaction was carried out in both a batch stirred reactor and in a re-circulating fixed-bed reactor. In the first system, the effect of various reaction parameters on catalytic behaviour was investigated: type of solvent or co-solvent, and particle size. With the second reactor type, I investigated the possibility to use a continuous system, and the catalyst shaped in extrudates (instead of powder), in order to avoid the catalyst filtration step. Finally, part D deals with the study of a new process for the valorisation of glycerol, by means of transformation into valuable chemicals. This molecule is nowadays produced in big amount, being a co-product in biodiesel synthesis; therefore, it is considered a raw material from renewable resources (a bio-platform molecule). Initially, we tested the oxidation of glycerol in the liquid-phase, with hydrogen peroxide and TS-1. However, results achieved were not satisfactory. Then we investigated the gas-phase transformation of glycerol into acrylic acid, with the intermediate formation of acrolein; the latter can be obtained by dehydration of glycerol, and then can be oxidized into acrylic acid. Actually, the oxidation step from acrolein to acrylic acid is already optimized at an industrial level; therefore, we decided to investigate in depth the first step of the process. I studied the reactivity of heterogeneous acid catalysts based on sulphated zirconia. Tests were carried out both in aerobic and anaerobic conditions, in order to investigate the effect of oxygen on the catalyst deactivation rate (one main problem usually met in glycerol dehydration). Finally, I studied the reactivity of bifunctional systems, made of Keggin-type polyoxometalates, either alone or supported over sulphated zirconia, in this way combining the acid functionality (necessary for the dehydrative step) with the redox one (necessary for the oxidative step). In conclusion, during my PhD work I investigated reactions that apply the “green chemistry” rules and strategies; in particular, I studied new greener approaches for the synthesis of chemicals (Part A and Part B), the optimisation of reaction parameters to make the oxidation process more flexible (Part C), and the use of a bioplatform molecule for the synthesis of a chemical intermediate (Part D).

Nuovi ingredienti funzionali per l'applicazione in campo alimentare

The Mediterranean diet is rich in healthy substances such as fibres, vitamins and phenols. Often these molecules are lost during food processing. Olive oil milling waste waters, brans, grape skins are some of the most relevant agri-food by-products in the Mediterranean countries. These wastes are still rich in extremely valuable molecules, such as phenolic antioxidants, that have several interesting health promoting properties. Using innovative environmental friendly technologies based in the rational use of enzymatic treatment is possible to obtain from agri-food by-products new ingredients containing antioxidants that can be used as functional ingredients in order to produce fortified foods. These foods, having health protecting/promoting properties, on top of the traditional nutritional properties, are attracting consumer’s attentions due to the increasing awareness on health protection through prevention. The use of these new ingredients in different food preparation was studied in order to evaluate the effects that the food processing might have on the antioxidant fraction, the effect of these ingredient on foods appearances as well as the impact in terms of taste and scent, crucial feature for the acceptability of the final product. Using these new ingredients was possible to produce antioxidant bred, pasta, cheese, cookies and ice-cream. These food products retains very well the antioxidant properties conferred by the added ingredients despite the very different treatments that were performed. The food obtained had a good palatability and in some cases the final product had also a good success on the market.

Pretrattamenti termo-meccanici ed enzimatici su scarti dell'industria enologica per la produzione di Biogas

A fundamental assumption for by-product from winery industy waste-management is their economic and commercial increase in value. High energetic value recovery from winery industry is an attractive economic solution to stimulate new sustainable process. Approach of this work is based about physic and biological treatment with grape stalks and grape marc to increase polysaccharides components of cell wall and energetic availability of this by-products. Grape stalks for example have a high percentage of lignin and cellulose and can’t be used, whitout pretreatment, for an anaerobic digestion process. Our findings show enzymatic and thermo-mechanical pre-treatments in combined application for optimise hydrolytic mechanism on winemaking wastes which represents 0,9 milion ton/year in Italy and on straw, cereal by-products with high lignin content. A screening of specifically industrial enzymatic complex for the hydrolysis lignocellulosic biomass were tested using the principal polysaccharides component of the vegetal cells. Combined thermo-mechanical and enzymatic pretreatment improve substrates conversion in batch test fermentation experiment. The conservation of the grape stalks, at temperature above 0°C, allow the growth of spontaneus fermentation that reduce their polysaccharides content so had investigated anarobic condition of conservation. The other objective of this study was to investigate the capability of a proprietary strain of L.buchneri LN 40177 to enhance the accessibility of fermentable forage constituents during the anaerobic conservation process by releasing the enzyme ferulate esterase. The time sequence study by batch tests showed that the L. buchneri LN-40177 inoculated grape stalk substrate was more readily available in the fermenter. In batch tests with grape stalk, after mechanical treatment, the L. buchneri LN41077 treated substrate yielded on average 70% more biogas per kg/DM. Thermo-mechanical, enzymatic and biological treatment with L. buchneri LN-40177 can increase the biogas production from low fermented biomasses and the consequent their useful in anaerobic biodigesters for agro-bioenergy production.

Produzione di bioidrogeno in dark fermentation da scarti dell'industria agroalimentale mediante l'impiego di batteri ipertermofili

La presente tesi di dottorato ha come argomento la produzione d’idrogeno per via fermentativa sfruttando il metabolismo anaerobico di particolari batteri estremofili del genere Thermotoga. In questo lavoro, svolto in seno al progetto Bio-Hydro, sfruttando reattori batch da 116 mL, è stato selezionato il ceppo migliore di Thermotoga fra i quatto ceppi testati: T. neapolitana. Una volta individuato il candidato batterico migliore è stato individuato il valore ottimale di pH (8.5 a t.amb) per la produzione d’idrogeno. Un intenso lavoro è stato svolto sul medium di coltura permettendone la minimizzazione e rendendolo così economicamente sostenibile per il suo utilizzo nel reattore da 19L; in questo caso il glucosio è stato completamente sostituito con due sottoprodotti agroindustriali individuati in precedenza, il melasso di barbabietola e il siero di latte. Sono stati poi eliminati i gravosi micronutrienti e le vitamine. È stata sfruttata la capacità di T. neapolitana di produrre biofilm e sono stati testati 4 diversi supporti in vetro sinterizzato e ceramici, tali test hanno permesso di individuare Biomax come supporto migliore. Sono stati svolti studi sul metabolismo di T. neapolitana volti ad individuare le concentrazioni inibenti di ogni substrato testato, l’inibizione da prodotto (idrogeno) e l’inibizione da ossigeno. Tutte queste prove hanno dato le conoscenze di base per la conduzione di esperienze su reattore da 19L. L’innovativo reattore di tipo SPCSTR è stato interamente studiato, progettato e costruito presso il DICMA. dell’Università di Bologna. La conduzione di esperienze batch su SPCSTR ha dato la possibilità di verificare il funzionamento del nuovo tipo d’impianto. Presso il Wageningen UR (NL), è stata svolta la selezione del miglior ceppo di Caldicellulosisruptor fra 3 testati e del miglior supporto per la produzione d’idrogeno; è stato poi costruito testato e condotto in continuo l’innovativo reattore CMTB.

Vanillin production from ferulic acid with Pseudomonas fluorescens BF13-1p4

Bioconversion of ferulic acid to vanillin represents an attractive opportunity for replacing synthetic vanillin with a bio-based product, that can be label “natural”, according to current food regulations. Ferulic acid is an abundant phenolic compound in cereals processing by-products, such as wheat bran, where it is linked to the cell wall constituents. In this work, the possibility of producing vanillin from ferulic acid released enzymatically from wheat bran was investigated by using resting cells of Pseudomonas fluorescens strain BF13-1p4 carrying an insertional inactivation of vdh gene and ech and fcs BF13 genes on a low copy number plasmid. Process parameters were optimized both for the biomass production phase and the bioconversion phase using food-grade ferulic acid as substrate and the approach of changing one variable while fixing the others at a certain level followed by the response surface methodology (RSM). Under optimized conditions, vanillin up to 8.46 mM (1.4 g/L) was achieved, whereas highest productivity was 0.53 mmoles vanillin L-1 h-1). Cocktails of a number of commercial enzyme (amylases, xylanases, proteases, feruloyl esterases) combined with bran pre-treatment with steam explosion and instant controlled pressure drop technology were then tested for the release of ferulic acid from wheat bran. The highest ferulic acid release was limited to 15-20 % of the ferulic acid occurring in bran, depending on the treatment conditions. Ferulic acid 1 mM in enzymatic hydrolyzates could be bioconverted into vanillin with molar yield (55.1%) and selectivity (68%) comparable to those obtained with food-grade ferulic acid after purification from reducing sugars with a non polar adsorption resin. Further improvement of ferulic acid recovery from wheat bran is however required to make more attractive the production of natural vanillin from this by-product.

Production of bioactive peptides through sequencial action of Yarrowia lipolytica proteases and chemical glycation

This PhD thesis is aimed at studying the suitability of proteases realised by Yarrowia lipolytica to hydrolyse proteins of different origins available as industrial food by-products. Several strains of Y. lipolytica have been screened for the production of extracellular proteases by zymography. On the basis of the results some strains released only a protease having a MW of 37 kDa, which corresponds to the already reported acidic protease, while other produced prevalently or only a protease with a MW higher than 200 kDa. The proteases have been screened for their "cold attitude" on gelatin, gluten and skim milk. This property can be relevant from a biotechnological point of view in order to save energy consumption during industrial processes. Most of the strains used were endowed with proteolytic activity at 6 °C on all the three proteins. The proteolytic breakdown profiles of the proteins, detected at 27 °C, were different related to the specific strains of Y. lipolytica. The time course of the hydrolysis, tested on gelatin, affected the final bioactivities of the peptide mixtures produced. In particular, an increase in both the antioxidant and antimicrobial activities was detected when the protease of the strain Y. lipolytica 1IIYL4A was used. The final part of this work was focused on the improvement of the peptides bioactivities through a novel process based on the production of glycopeptides. Firstly, the main reaction parameters were optimized in a model system, secondly a more complex system, based on gluten hydrolysates, was taken into consideration to produce glycopeptides. The presence of the sugar moiety reduced the hydrophobicity of the glycopeptides, thus affecting the final antimicrobial activity which was significantly improved. The use of this procedure could be highly effective to modify peptides and can be employed to create innovative functional peptides using a mild temperature process.

Catalytic processes for the transformation of ethanol into acetonitrile

This thesis deals with the transformation of ethanol into acetonitrile. Two approaches are investigated: (a) the ammoxidation of ethanol to acetonitrile and (b) the amination of ethanol to acetonitrile. The reaction of ethanol ammoxidation to acetonitrile has been studied using several catalytic systems, such as vanadyl pyrophosphate, supported vanadium oxide, multimetal molibdates and antimonates. The main conclusions are: (I) The surface acidity must be very low, because acidity catalyzes several undesired reactions, such as the formation of ethylene, and of heavy compounds as well. (II) Supported vanadium oxide is the catalyst showing the best catalytic behaviour, but the role of the support is of crucial importance. (III) Both metal molybdates and antimonates show interesting catalytic behaviour, but are poorly active, and probably require harder conditions than those used with the V oxide-based catalysts. (IV) One key point in the reaction network is the rate of reaction between acetaldehyde (the first intermediate) and ammonia, compared to the parallel rates of acetaldehyde transformation into by-products (CO, CO2, HCN, heavy compounds). Concerning the non-oxidative process, two possible strategies are investigated: (a) the ethanol ammonolysis to ethylamine coupled with ethylamine dehydrogenation, and (b) the direct non-reductive amination of ethanol to acetonitrile. Despite the good results obtained in each single step, the former reaction does not lead to good results in terms of yield to acetonitrile. The direct amination can be catalyzed with good acetonitrile yield over catalyst based on supported metal oxides. Strategies aimed at limiting catalyst deactivation have also been investigated.

New catalytic processes for the upgrading of furfural and 5-hydroxymethylfurfural to chemicals and fuels

The demand of energy, fuels and chemicals is increasing due to the strong growth of some countries in the developing world and the development of the world economy. Unfortunately, the general picture derived sparked an exponential increase in crude oil prices with a consequent increase of the chemical, by-products and energy, depleting the global market. Nowadays biomass are the most promising alternative to fossil fuels for the production of chemicals and fuels. In this work, the development of three different catalytic processes for the valorization of biomass-derived has been investigated. 5-hydroxymethylfurfural oxidation was studied under mild reaction condition using gold and gold/copper based catalysts synthetized from pre-formed nanoparticles and supported onto TiO2 and CeO2. The analysis conducted on catalysts showed the formation of alloys gold/copper and a strong synergistic effect between the two metals. For this reason the bimetallic catalysts supported on titania showed a higher catalytic activity respect to the monometallic catalysts. The process for the production of 2,5-bishydroxymethyl furan (BHMF) was also optimized by means the 5-hydroxymethylfurfural hydrogenation using the Shvo complex. Complete conversion of HMF was achieved working at 90 °C and 10 bar of hydrogen. The complex was found to be re-usable for at least three catalytic cycles without suffering any type of deactivation. Finally, the hydrogenation of furfural and HMF was carried out, developing the process of hydrogen transfer by using MgO as a catalyst and methanol as a hydrogen donor. Quantitative yields to alcohols have been achieved in a few hours working in mild condition: 160 °C and at autogenous pressure. The only by-products formed were light products such as CO, CO2 and CH4 (products derived from methanol transformation), easily separable from the reaction solution depressurizing the reactor.

Lipid quality and oxidative stability in food products from animal origin, as affected by breeding factor

Nowadays it is requested more investigations on alternative rearing systems that are able to improve poultry welfare and to warrant high-quality and safe meat products. This thesis work was focused on the evaluation of the oxidative stability of poultry meats, obtained with different rearing systems, diets (supplemented with bioactive compounds), and packaging conditions. The thesis work was divided into the following parts: - Evaluation of the effects of different rearing systems on the quality, fatty acid composition and oxidative stability of poultry thigh and breast meat belonging to different product categories (“rotisserie” and “cut-up” carcasses); - Evaluation of the effects of different rearing systems and packaging conditions on the shelf-life of poultry thigh meat stored at 4°C for 14 days, and the effects of feed supplementation with thymol (control diet and diet with 2 different concentration of thymol) and packaging conditions on lipid oxidation of poultry thigh meat shelf-life (stored at 4°C for 14 days). The oxidative stability of poultry meat was studied by means of the spectrophotometric determinations of peroxide value and thiobarbituric acid reactive substances. - Evaluation of anti-inflammatory effects of different flavonoids (thymol, luteolin, tangeretin, sulforaphane, polymethoxyflavones, curcumin derivates) to detect their biological activity in LPS-stimulated RAW 264.7 macrophage cells in vitro, in order to study more in depth their action mechanisms. It was evaluated the cell vitality (MTT assay), nitrite concentration and protein profile. The study was focused on the identification of potential dietary bioactive compounds in order to investigate their biological activity and possible synergic effects, and to develop new suitable strategies for long-term promotion of human health, in particular against cancer.