Temperature Variation Aware Energy Optimization in Heterogeneous MPSoCs

Thermal effects are rapidly gaining importance in nanometer heterogeneous integrated systems. Increased power density, coupled with spatio-temporal variability of chip workload, cause lateral and vertical temperature non-uniformities (variations) in the chip structure. The assumption of an uniform temperature for a large circuit leads to inaccurate determination of key design parameters. To improve design quality, we need precise estimation of temperature at detailed spatial resolution which is very computationally intensive. Consequently, thermal analysis of the designs needs to be done at multiple levels of granularity. To further investigate the flow of chip/package thermal analysis we exploit the Intel Single Chip Cloud Computer (SCC) and propose a methodology for calibration of SCC on-die temperature sensors. We also develop an infrastructure for online monitoring of SCC temperature sensor readings and SCC power consumption. Having the thermal simulation tool in hand, we propose MiMAPT, an approach for analyzing delay, power and temperature in digital integrated circuits. MiMAPT integrates seamlessly into industrial Front-end and Back-end chip design flows. It accounts for temperature non-uniformities and self-heating while performing analysis. Furthermore, we extend the temperature variation aware analysis of designs to 3D MPSoCs with Wide-I/O DRAM. We improve the DRAM refresh power by considering the lateral and vertical temperature variations in the 3D structure and adapting the per-DRAM-bank refresh period accordingly. We develop an advanced virtual platform which models the performance, power, and thermal behavior of a 3D-integrated MPSoC with Wide-I/O DRAMs in detail. Moving towards real-world multi-core heterogeneous SoC designs, a reconfigurable heterogeneous platform (ZYNQ) is exploited to further study the performance and energy efficiency of various CPU-accelerator data sharing methods in heterogeneous hardware architectures. A complete hardware accelerator featuring clusters of OpenRISC CPUs, with dynamic address remapping capability is built and verified on a real hardware.

Big data in health IoE in emergency situations: between the right to privacy and digital health innovation

The chapters of the thesis focus on a limited variety of selected themes in EU privacy and data protection law. Chapter 1 sets out the general introduction on the research topic. Chapter 2 touches upon the methodology used in the research. Chapter 3 conceptualises the basic notions from a legal standpoint. Chapter 4 examines the current regulatory regime applicable to digital health technologies, healthcare emergencies, privacy, and data protection. Chapter 5 provides case studies on the application deployed in the Covid-19 scenario, from the perspective of privacy and data protection. Chapter 6 addresses the post-Covid European regulatory initiatives on the subject matter, and its potential effects on privacy and data protection. Chapter 7 is the outcome of a six-month internship with a company in Italy and focuses on the protection of fundamental rights through common standardisation and certification, demonstrating that such standards can serve as supporting tools to guarantee the right to privacy and data protection in digital health technologies. The thesis concludes with the observation that finding and transposing European privacy and data protection standards into scenarios, such as public healthcare emergencies where digital health technologies are deployed, requires rapid coordination between the European Data Protection Authorities and the Member States guarantee that individual privacy and data protection rights are ensured.

Performance evaluation of detectors for digital radiography

To date the hospital radiological workflow is completing a transition from analog to digital technology. Since the X-rays digital detection technologies have become mature, hospitals are trading on the natural devices turnover to replace the conventional screen film devices with digital ones. The transition process is complex and involves not just the equipment replacement but also new arrangements for image transmission, display (and reporting) and storage. This work is focused on 2D digital detector’s characterization with a concern to specific clinical application; the systems features linked to the image quality are analyzed to assess the clinical performances, the conversion efficiency, and the minimum dose necessary to get an acceptable image. The first section overviews the digital detector technologies focusing on the recent and promising technological developments. The second section contains a description of the characterization methods considered in this thesis categorized in physical, psychophysical and clinical; theory, models and procedures are described as well. The third section contains a set of characterizations performed on new equipments that appears to be some of the most advanced technologies available to date. The fourth section deals with some procedures and schemes employed for quality assurance programs.

Utilizzo delle bande dell’Infrarosso Termico in tecniche di remote sensing per applicazioni in ambito urbano

Il presente studio si concentra sulle diverse applicazioni del telerilevamento termico in ambito urbano. Vengono inizialmente descritti la radiazione infrarossa e le sue interazioni con l’atmosfera terrestre, le leggi principali che regolano lo scambio di calore per irraggiamento, le caratteristiche dei sensori e le diverse applicazioni di termografia. Successivamente sono trattati nel dettaglio gli aspetti caratteristici della termografia da piattaforma satellitare, finalizzata principalmente alla valutazione del fenomeno dell'Urban Heat Island; vengono descritti i sensori disponibili, le metodologie di correzione per gli effetti atmosferici, per la stima dell'emissività delle superfici e per il calcolo della temperatura superficiale dei pixels. Viene quindi illustrata la sperimentazione effettuata sull'area di Bologna mediante immagini multispettrali ASTER: i risultati mostrano come sull'area urbana sia riscontrabile la presenza dell'Isola di Calore Urbano, anche se la sua quantificazione risulta complessa. Si procede quindi alla descrizione di potenzialità e limiti della termografia aerea, dei suoi diversi utilizzi, delle modalità operative di rilievo e degli algoritmi utilizzati per il calcolo della temperatura superficiale delle coperture edilizie. Tramite l’analisi di alcune esperienze precedenti vengono trattati l’influenza dell’atmosfera, la modellazione dei suoi effetti sulla radianza rilevata, i diversi metodi per la stima dell’emissività. Viene quindi introdotto il progetto europeo Energycity, finalizzato alla creazione di un sistema GeoWeb di supporto spaziale alle decisioni per la riduzione di consumi energetici e produzione di gas serra su sette città dell'Europa Centrale. Vengono illustrate le modalità di rilievo e le attività di processing dei datasets digitali per la creazione di mappe di temperatura superficiale da implementare nel sistema SDSS. Viene infine descritta la sperimentazione effettuata sulle immagini termiche acquisite nel febbraio 2010 sulla città di Treviso, trasformate in un mosaico georiferito di temperatura radiometrica tramite correzioni geometriche e radiometriche; a seguito della correzione per l’emissività quest’ultimo verrà trasformato in un mosaico di temperatura superficiale.

Antipodal random sequences with prescribed second-order statistics: application to Compressive Sensing and UWB system based on DS-CDMA

It is usual to hear a strange short sentence: «Random is better than...». Why is randomness a good solution to a certain engineering problem? There are many possible answers, and all of them are related to the considered topic. In this thesis I will discuss about two crucial topics that take advantage by randomizing some waveforms involved in signals manipulations. In particular, advantages are guaranteed by shaping the second order statistic of antipodal sequences involved in an intermediate signal processing stages. The first topic is in the area of analog-to-digital conversion, and it is named Compressive Sensing (CS). CS is a novel paradigm in signal processing that tries to merge signal acquisition and compression at the same time. Consequently it allows to direct acquire a signal in a compressed form. In this thesis, after an ample description of the CS methodology and its related architectures, I will present a new approach that tries to achieve high compression by design the second order statistics of a set of additional waveforms involved in the signal acquisition/compression stage. The second topic addressed in this thesis is in the area of communication system, in particular I focused the attention on ultra-wideband (UWB) systems. An option to produce and decode UWB signals is direct-sequence spreading with multiple access based on code division (DS-CDMA). Focusing on this methodology, I will address the coexistence of a DS-CDMA system with a narrowband interferer. To do so, I minimize the joint effect of both multiple access (MAI) and narrowband (NBI) interference on a simple matched filter receiver. I will show that, when spreading sequence statistical properties are suitably designed, performance improvements are possible with respect to a system exploiting chaos-based sequences minimizing MAI only.

Assimilation of Meteosat Second Generation (MSG) satellite data in a regional numerical weather prediction model using a one-dimensional variational approach

The quality of temperature and humidity retrievals from the infrared SEVIRI sensors on the geostationary Meteosat Second Generation (MSG) satellites is assessed by means of a one dimensional variational algorithm. The study is performed with the aim of improving the spatial and temporal resolution of available observations to feed analysis systems designed for high resolution regional scale numerical weather prediction (NWP) models. The non-hydrostatic forecast model COSMO (COnsortium for Small scale MOdelling) in the ARPA-SIM operational configuration is used to provide background fields. Only clear sky observations over sea are processed. An optimised 1D–VAR set-up comprising of the two water vapour and the three window channels is selected. It maximises the reduction of errors in the model backgrounds while ensuring ease of operational implementation through accurate bias correction procedures and correct radiative transfer simulations. The 1D–VAR retrieval quality is firstly quantified in relative terms employing statistics to estimate the reduction in the background model errors. Additionally the absolute retrieval accuracy is assessed comparing the analysis with independent radiosonde and satellite observations. The inclusion of satellite data brings a substantial reduction in the warm and dry biases present in the forecast model. Moreover it is shown that the retrieval profiles generated by the 1D–VAR are well correlated with the radiosonde measurements. Subsequently the 1D–VAR technique is applied to two three–dimensional case–studies: a false alarm case–study occurred in Friuli–Venezia–Giulia on the 8th of July 2004 and a heavy precipitation case occurred in Emilia–Romagna region between 9th and 12th of April 2005. The impact of satellite data for these two events is evaluated in terms of increments in the integrated water vapour and saturation water vapour over the column, in the 2 meters temperature and specific humidity and in the surface temperature. To improve the 1D–VAR technique a method to calculate flow–dependent model error covariance matrices is also assessed. The approach employs members from an ensemble forecast system generated by perturbing physical parameterisation schemes inside the model. The improved set–up applied to the case of 8th of July 2004 shows a substantial neutral impact.

Development and characterization of non-oxide ceramic composites for mechanical and tribological applications

The main reasons for the attention focused on ceramics as possible structural materials are their wear resistance and the ability to operate with limited oxidation and ablation at temperatures above 2000°C. Hence, this work is devoted to the study of two classes of materials which can satisfy these requirements: silicon carbide -based ceramics (SiC) for wear applications and borides and carbides of transition metals for ultra-high temperatures applications (UHTCs). SiC-based materials: Silicon carbide is a hard ceramic, which finds applications in many industrial sectors, from heat production, to automotive engineering and metals processing. In view of new fields of uses, SiC-based ceramics were produced with addition of 10-30 vol% of MoSi2, in order to obtain electro conductive ceramics. MoSi2, indeed, is an intermetallic compound which possesses high temperature oxidation resistance, high electrical conductivity (21·10-6 Ω·cm), relatively low density (6.31 g/cm3), high melting point (2030°C) and high stiffness (440 GPa). The SiC-based ceramics were hot pressed at 1900°C with addition of Al2O3-Y2O3 or Y2O3-AlN as sintering additives. The microstructure of the composites and of the reference materials, SiC and MoSi2, were studied by means of conventional analytical techniques, such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (SEM-EDS). The composites showed a homogeneous microstructure, with good dispersion of the secondary phases and low residual porosity. The following thermo-mechanical properties of the SiC-based materials were measured: Vickers hardness (HV), Young’s modulus (E), fracture toughness (KIc) and room to high temperature flexural strength (σ). The mechanical properties of the composites were compared to those of two monolithic SiC and MoSi2 materials and resulted in a higher stiffness, fracture toughness and slightly higher flexural resistance. Tribological tests were also performed in two configurations disco-on-pin and slideron cylinder, aiming at studying the wear behaviour of SiC-MoSi2 composites with Al2O3 as counterfacing materials. The tests pointed out that the addition of MoSi2 was detrimental owing to a lower hardness in comparison with the pure SiC matrix. On the contrary, electrical measurements revealed that the addition of 30 vol% of MoSi2, rendered the composite electroconductive, lowering the electrical resistance of three orders of magnitude. Ultra High Temperature Ceramics: Carbides, borides and nitrides of transition metals (Ti, Zr, Hf, Ta, Nb, Mo) possess very high melting points and interesting engineering properties, such as high hardness (20-25 GPa), high stiffness (400-500 GPa), flexural strengths which remain unaltered from room temperature to 1500°C and excellent corrosion resistance in aggressive environment. All these properties place the UHTCs as potential candidates for the development of manoeuvrable hypersonic flight vehicles with sharp leading edges. To this scope Zr- and Hf- carbide and boride materials were produced with addition of 5-20 vol% of MoSi2. This secondary phase enabled the achievement of full dense composites at temperature lower than 2000°C and without the application of pressure. Besides the conventional microstructure analyses XRD and SEM-EDS, transmission electron microscopy (TEM) was employed to explore the microstructure on a small length scale to disclose the effective densification mechanisms. A thorough literature analysis revealed that neither detailed TEM work nor reports on densification mechanisms are available for this class of materials, which however are essential to optimize the sintering aids utilized and the processing parameters applied. Microstructural analyses, along with thermodynamics and crystallographic considerations, led to disclose of the effective role of MoSi2 during sintering of Zrand Hf- carbides and borides. Among the investigated mechanical properties (HV, E, KIc, σ from room temperature to 1500°C), the high temperature flexural strength was improved due to the protective and sealing effect of a silica-based glassy phase, especially for the borides. Nanoindentation tests were also performed on HfC-MoSi2 composites in order to extract hardness and elastic modulus of the single phases. Finally, arc jet tests on HfC- and HfB2-based composites confirmed the excellent oxidation behaviour of these materials under temperature exceeding 2000°C; no cracking or spallation occurred and the modified layer was only 80-90 μm thick.

Valorizzazione di cartografia storica attraverso moderne tecniche geomatiche: recupero metrico, elaborazione e consultazione in ambiente digitale

“Cartographic heritage” is different from “cartographic history”. The second term refers to the study of the development of surveying and drawing techniques related to maps, through time, i.e. through different types of cultural environment which were background for the creation of maps. The first term concerns the whole amount of ancient maps, together with these different types of cultural environment, which the history has brought us and which we perceive as cultural values to be preserved and made available to many users (public, institutions, experts). Unfortunately, ancient maps often suffer preservation problems of their analog support, mostly due to aging. Today, metric recovery in digital form and digital processing of historical cartography allow preserving map heritage. Moreover, modern geomatic techniques give us new chances of using historical information, which would be unachievable on analog supports. In this PhD thesis, the whole digital processing of recovery and elaboration of ancient cartography is reported, with a special emphasis on the use of digital tools in preservation and elaboration of cartographic heritage. It is possible to divide the workflow into three main steps, that reflect the chapter structure of the thesis itself: • map acquisition: conversion of the ancient map support from analog to digital, by means of high resolution scanning or 3D surveying (digital photogrammetry or laser scanning techniques); this process must be performed carefully, with special instruments, in order to reduce deformation as much as possible; • map georeferencing: reproducing in the digital image the native metric content of the map, or even improving it by selecting a large number of still existing ground control points; this way it is possible to understand the projection features of the historical map, as well as to evaluate and represent the degree of deformation induced by the old type of cartographic transformation (that can be unknown to us), by surveying errors or by support deformation, usually all errors of too high value with respect to our standards; • data elaboration and management in a digital environment, by means of modern software tools: vectorization, giving the map a new and more attractive graphic view (for instance, by creating a 3D model), superimposing it on current base maps, comparing it to other maps, and finally inserting it in GIS or WebGIS environment as a specific layer. The study is supported by some case histories, each of them interesting from the point of view of one digital cartographic elaboration step at least. The ancient maps taken into account are the following ones: • three maps of the Po river delta, made at the end of the XVI century by a famous land-surveyor, Ottavio Fabri (he is single author in the first map, co-author with Gerolamo Pontara in the second map, co-author with Bonajuto Lorini and others in the third map), who wrote a methodological textbook where he explains a new topographical instrument, the squadra mobile (mobile square) invented and used by himself; today all maps are preserved in the State Archive of Venice; • the Ichnoscenografia of Bologna by Filippo de’ Gnudi, made in the 1702 and today preserved in the Archiginnasio Library of Bologna; it is a scenographic view of the city, captured in a bird’s eye flight, but also with an icnographic value, as the author himself declares; • the map of Bologna by the periti Gregorio Monari and Antonio Laghi, the first map of the city derived from a systematic survey, even though it was made only ten years later (1711–1712) than the map by de’ Gnudi; in this map the scenographic view was abandoned, in favor of a more correct representation by means of orthogonal projection; today the map is preserved in the State Archive of Bologna; • the Gregorian Cadastre of Bologna, made in 1831 and updated until 1927, now preserved in the State Archive of Bologna; it is composed by 140 maps and 12 brogliardi (register volumes). In particular, the three maps of the Po river delta and the Cadastre were studied with respect to their acquisition procedure. Moreover, the first maps were analyzed from the georeferencing point of view, and the Cadastre was analyzed with respect to a possible GIS insertion. Finally, the Ichnoscenografia was used to illustrate a possible application of digital elaboration, such as 3D modeling. Last but not least, we must not forget that the study of an ancient map should start, whenever possible, from the consultation of the precious original analogical document; analysis by means of current digital techniques allow us new research opportunities in a rich and modern multidisciplinary context.

Influence of nitrogen and soil physical characteristics on belowground carbon flux dynamics of woody plants

At ecosystem level soil respiration (Rs) represents the largest carbon (C) flux after gross primary productivity, being mainly generated by root respiration (autotrophic respiration, Ra) and soil microbial respiration (heterotrophic respiration, Rh). In the case of terrestrial ecosystems, soils contain the largest C-pool, storing twice the amount of C contained in plant biomass. Soil organic matter (SOM), representing the main C storage in soil, is decomposed by soil microbial community. This process produces CO2 which is mainly released as Rh. It is thus relevant to understand how microbial activity is influenced by environmental factors like soil temperature, soil moisture and nutrient availability, since part of the CO2 produced by Rh, directly increases atmospheric CO2 concentration and therefore affects the phenomenon of climate change. Among terrestrial ecosystems, agricultural fields have traditionally been considered as sources of atmospheric CO2. In agricultural ecosystems, in particular apple orchards, I identified the role of root density, soil temperature, soil moisture and nitrogen (N) availability on Rs and on its two components, Ra and Rh. To do so I applied different techniques to separate Rs in its two components, the ”regression technique” and the “trenching technique”. I also studied the response of Ra to different levels of N availability, distributed either in a uniform or localized way, in the case of Populus tremuloides trees. The results showed that Rs is mainly driven by soil temperature, to which it is positively correlated, that high levels of soil moisture have inhibiting effects, and that N has a negligible influence on total Rs, as well as on Ra. Further I found a negative response of Rh to high N availability, suggesting that microbial decomposition processes in the soil are inhibited by the presence of N. The contribution of Ra to Rs was of 37% on average.

Global scale investigation of cirrus clouds properties using active and passive sensors

A year of satellite-borne lidar CALIOP data is analyzed and statistics on occurrence and distribution of bulk properties of cirri are provided. The relationship between environmental and cloud physical parameters and the shape of the backscatter profile (BSP) is investigated. It is found that CALIOP BSP is mainly affected by cloud geometrical thickness while only minor impacts can be attributed to other quantities such as optical depth or temperature. To fit mean BSPs as functions of geometrical thickness and position within the cloud layer, polynomial functions are provided. It is demonstrated that, under realistic hypotheses, the mean BSP is linearly proportional to the IWC profile. The IWC parameterization is included into the RT-RET retrieval algorithm, that is exploited to analyze infrared radiance measurements in presence of cirrus clouds during the ECOWAR field campaign. Retrieved microphysical and optical properties of the observed cloud are used as input parameters in a forward RT simulation run over the 100-1100 cm-1 spectral interval and compared with interferometric data to test the ability of the current single scattering properties database of ice crystal to reproduce realistic optical features. Finally a global scale investigation of cirrus clouds is performed by developing a collocation algorithm that exploits satellite data from multiple sensors (AIRS, CALIOP, MODIS). The resulting data set is utilized to test a new infrared hyperspectral retrieval algorithm. Retrieval products are compared to data and in particular the cloud top height (CTH) product is considered for this purpose. A better agreement of the retrieval with the CALIOP CTH than MODIS is found, even if some cases of underestimation and overestimation are observed.

L'adeguamento di tradizionali laboratori europei di restauro fotochimico alle tecniche digitali

La presente ricerca ha avuto come obbietivo studiare come stia avvenendo l'adattamento dei tradizionali laboratori fotochimici di film alle tecniche digitali attraverso l'analisi delle politiche di preservazione, del restauro, dei costi relativi all’acquisto di nuove apparecchiature e della migrazione ai nuovi media presso il British Film Institute (BFI), lo Svenska Filminstitutet (SFI), l’Eye Filmmuseum, L'Immagine Ritrovata e ANIM - Cinemateca Portuguesa. A questo scopo è stato utilizzato il metodo dello studio di caso, in cui sono state effettuate interviste con gestori e tecnici delle istituzioni citate al fine di rispondere al quesito della presente ricerca: quali sono l’impatto e le implicazioni di questo adattamento? Quali sono i risultati raggiunti con le nuove attrezzature e metodi di restauro e preservazione? Per arrivare a rispondere a queste domande lo studio è stato diviso in due sezioni. Nella prima parte, sono riportate le interviste svolte presso SFI, BFI, Eye e L'Immagine Ritrovata, realizzate al fine di ottenere dati che permettessero di formulare un'intervista più completa e approfondita. Successivamente, questa intervista più dettagliata è stata condotta con una sola istituzione, la Cinemateca Portuguesa. Pertanto, nella seconda parte dello studio di caso, sono state realizzate interviste a tecnici e dirigenti di ANIM - Cinemateca Portuguesa e dei suoi laboratori partner. L'analisi dei risultati comprende tutte le informazioni provenienti dalle cinque istituzioni intervistate. È stato notato che l'adattamento al digitale ha effettivamente apportato miglioramenti nella preservazione e nel recupero del materiale fotochimico, ma ciò ha anche fatto sorgere alcuni dilemmi nei laboratori. C'è apprensione per la scarsità di materiale della filiera fotochimica e per una sua ipotetica fine nel prossimo futuro, poiché non ci sono ancora sufficienti conoscenze sulla filiera digitale e sul comportamento di questi media con il passare del tempo. Gli intervistati hanno altresì dimostrato positività riguardo alle tecnologie digitali.