Design and development of new pressure sensors for aerodynamic applications

This artwork reports on two different projects that were carried out during the three years of Doctor of the Philosophy course. In the first years a project regarding Capacitive Pressure Sensors Array for Aerodynamic Applications was developed in the Applied Aerodynamic research team of the Second Faculty of Engineering, University of Bologna, Forlì, Italy, and in collaboration with the ARCES laboratories of the same university. Capacitive pressure sensors were designed and fabricated, investigating theoretically and experimentally the sensor’s mechanical and electrical behaviours by means of finite elements method simulations and by means of wind tunnel tests. During the design phase, the sensor figures of merit are considered and evaluated for specific aerodynamic applications. The aim of this work is the production of low cost MEMS-alternative devices suitable for a sensor network to be implemented in air data system. The last two year was dedicated to a project regarding Wireless Pressure Sensor Network for Nautical Applications. Aim of the developed sensor network is to sense the weak pressure field acting on the sail plan of a full batten sail by means of instrumented battens, providing a real time differential pressure map over the entire sail surface. The wireless sensor network and the sensing unit were designed, fabricated and tested in the faculty laboratories. A static non-linear coupled mechanical-electrostatic simulation, has been developed to predict the pressure versus capacitance static characteristic suitable for the transduction process and to tune the geometry of the transducer to reach the required resolution, sensitivity and time response in the appropriate full scale pressure input A time dependent viscoelastic error model has been inferred and developed by means of experimental data in order to model, predict and reduce the inaccuracy bound due to the viscolelastic phenomena affecting the Mylar® polyester film used for the sensor diaphragm. The development of the two above mentioned subjects are strictly related but presently separately in this artwork.

Studio del comportamento meccanico di smalti porcellanati per substrati metallici

Composite porcelain enamels are inorganic coatings for metallic components based on a special ceramic-vitreous matrix in which specific additives are randomly dispersed. The ceramic-vitreous matrix is made by a mixture of various raw materials and elements and in particular it is based on boron-silicate glass added with metal oxides(1) of titanium, zinc, tin, zirconia, alumina, ecc. These additions are often used to improve and enhance some important performances such as corrosion(2) and wear resistance, mechanical strength, fracture toughness and also aesthetic functions. The coating process, called enamelling, depends on the nature of the surface, but also on the kind of the used porcelain enamel. For metal sheets coatings two industrial processes are actually used: one based on a wet porcelain enamel and another based on a dry-silicone porcelain enamel. During the firing process, that is performed at about 870°C in the case of a steel substrate, the enamel raw material melts and interacts with the metal substrate so enabling the formation of a continuous varying structure. The interface domain between the substrate and the external layer is made of a complex material system where the ceramic vitreous and the metal constituents are mixed. In particular four main regions can be identified, (i) the pure metal region, (ii) the region where the metal constituents are dominant compared with the ceramic vitreous components, (iii) the region where the ceramic vitreous constituents are dominant compared with the metal ones, and the fourth region (iv) composed by the pure ceramic vitreous material. It has also to be noticed the presence of metallic dendrites that hinder the substrate and the external layer passing through the interphase region. Each region of the final composite structure plays a specific role: the metal substrate has mainly the structural function, the interphase region and the embedded dendrites guarantee the adhesion of the external vitreous layer to the substrate and the external vitreous layer is characterized by an high tribological, corrosion and thermal shock resistance. Such material, due to its internal composition, functionalization and architecture can be considered as a functionally graded composite material. The knowledge of the mechanical, tribological and chemical behavior of such composites is not well established and the research is still in progress. In particular the mechanical performances data about the composite coating are not jet established. In the present work the Residual Stresses, the Young modulus and the First Crack Failure of the composite porcelain enamel coating are studied. Due to the differences of the porcelain composite enamel and steel thermal properties the enamelled steel sheets have residual stresses: compressive residual stress acts on the coating and tensile residual stress acts on the steel sheet. The residual stresses estimation has been performed by measuring the curvature of rectangular one-side coated specimens. The Young modulus and the First Crack Failure (FCF) of the coating have been estimated by four point bending tests (3-7) monitored by means of the Acoustic Emission (AE) technique(5,6). In particular the AE information has been used to identify, during the bending tests, the displacement domain over which no coating failure occurs (Free Failure Zone, FFZ). In the FFZ domain, the Young modulus has been estimated according to ASTM D6272-02. The FCF has been calculated as the ratio between the displacement at the first crack of the coating and the coating thickness on the cracked side. The mechanical performances of the tested coated specimens have also been related and discussed to respective microstructure and surface characteristics by double entry charts.

The language of action. How language translates the dynamics of our actions.

The general aim of the thesis was to investigate how and to what extent the characteristics of action organization are reflected in language, and how they influence language processing and understanding. Even though a huge amount of research has been devoted to the study of the motor effects of language, this issue is very debated in literature. Namely, the majority of the studies have focused on low-level motor effects such as effector-relatedness of action, whereas only a few studies have started to systematically investigate how specific aspects of action organization are encoded and reflected in language. After a review of previous studies on the relationship between language comprehension and action (chapter 1) and a critical discussion of some of them (chapter 2), the thesis is composed by three experimental chapters, each devoted to a specific aspect of action organization. Chapter 3 presents a study designed with the aim to disentangle the effective time course of the involvement of the motor system during language processing. Three kinematics experiments were designed in order to determine whether and, at which stage of motor planning and execution effector-related action verbs influence actions executed with either the same or a different effector. Results demonstrate that the goal of an action can be linguistically re-activated, producing a modulation of the motor response. In chapter 4, a second study investigates the interplay between the role of motor perspective (agent) and the organization of action in motor chains. More specifically, this kinematics study aims at deepening how goal can be translated in language, using as stimuli simple sentences composed by a pronoun (I, You, He/She) and a verb. Results showed that the perspective activated by the pronoun You reflects the motor pattern of the “agent” combined with the chain structure of the verb. These data confirm an early involvement of the motor system in language processing, suggesting that it is specifically modulated by the activation of the agent’s perspective. In chapter 5, the issue of perspective is specifically investigated, focusing on its role in language comprehension. In particular, this study aimed at determining how a specific perspective (induced for example by a personal pronoun) modulates motor behaviour during and after language processing. A classical compatibility effect (the Action-sentence compatibility effect) has been used to this aim. In three behavioural experiments the authors investigated how the ACE is modulated by taking first or third person perspective. Results from these experiments showed that the ACE effect occurs only when a first-person perspective is activated by the sentences used as stimuli. Overall, the data from this thesis contributed to disentangle several aspects of how action organization is translated in language, and then reactivated during language processing. This constitutes a new contribution to the field, adding lacking information on how specific aspects such as goal and perspective are linguistically described. In addition, these studies offer a new point of view to understand the functional implications of the involvement of the motor system during language comprehension, specifically from the point of view of our social interactions.

Static analysis of functionally graded cylindrical and conical shells or panels using the generalized unconstrained third order theory coupled with the stress recovery

A 2D Unconstrained Third Order Shear Deformation Theory (UTSDT) is presented for the evaluation of tangential and normal stresses in moderately thick functionally graded conical and cylindrical shells subjected to mechanical loadings. Several types of graded materials are investigated. The functionally graded material consists of ceramic and metallic constituents. A four parameter power law function is used. The UTSDT allows the presence of a finite transverse shear stress at the top and bottom surfaces of the graded shell. In addition, the initial curvature effect included in the formulation leads to the generalization of the present theory (GUTSDT). The Generalized Differential Quadrature (GDQ) method is used to discretize the derivatives in the governing equations, the external boundary conditions and the compatibility conditions. Transverse and normal stresses are also calculated by integrating the three dimensional equations of equilibrium in the thickness direction. In this way, the six components of the stress tensor at a point of the conical or cylindrical shell or panel can be given. The initial curvature effect and the role of the power law functions are shown for a wide range of functionally conical and cylindrical shells under various loading and boundary conditions. Finally, numerical examples of the available literature are worked out.