Development and chemo-mechanical characterization of eco-compatible extenders containing REOB and recycled tyres’ rubber for the production of greener bituminous binders

The concepts of circular economy and sustainability are the basis of the present experimental research that seeks to reduce the environmental impact of traditional road construction materials. This study mainly focuses on the development and the chemo-mechanical characterization of bitumen extenders containing rubber (R) from end-of-life tyres (ELTs) and re-refined engine oil bottoms (REOBs) for the production of innovative and eco-friendly extended bitumens (i.e. bituminous binders containing 25%wt. of recycled products) and asphalt mixtures. In order to create more sustainable asphalt mixes, also recycled aggregates are used for partial replacement of virgin natural aggregates in the aggregate skeleton. The experimental program encompassed five successive steps: (i) the evaluation of physicochemical properties of R and REOB, (ii) the definition of the optimal extenders by the development of a new protocol and their characterizations, (iii) the realization and investigation of the chemo-rheological responses of the extended bitumens at different boundary conditions, (iv) the assessment of the effectiveness of analytical method to predict the rheological parameters of extended bitumens and, finally, (v) the analysis of the mechanical performances of the corresponding asphalt mixtures. A standard 50/70 penetration grade bitumen was chosen as a reference material and the main constituent of the innovative bituminous products. The results of this study underlined the importance of material characterization. The incorporation of R-REOB extenders strongly affects the chemo-rheological responses of the resulting extended bitumens and asphalt mixtures overall the boundary conditions. While the presence of R and the consequent formation of a polymer network improves the elasticity of the final products, especially at high test temperatures; the addition of REOB, softens the bituminous binders and asphalt mixes increasing their response at low test temperatures. Nonetheless, the use of recycled products increased the susceptibility of bituminous material under damaging conditions, which would need further investigations.

Sustainable pavements for rural scenarios: laboratory and in-situ characterization of recycled materials and innovative construction solutions

Growing need for infrastructure has led to expanding research on advances in road pavement materials. Finding solutions that are sustainable, environmentally friendly and cost-efficient is a priority. Focusing such efforts on low-traffic and rural roads can contribute with a significant progress in the vital circulatory system of transport for rural and agricultural areas. An important alternative material for pavement construction is recycled aggregates from solid wastes, including waste from civil engineering activities, mainly construction and demolition. A literature review on studies is made; it is performed a planned set of laboratory testing procedures aimed to fully characterize and assess the potential in-situ mechanical performance and chemical impact. Furthermore, monitoring the full-scale response of the selected materials in a real field construction site, including the production, laying and compaction operations. Moreover, a novel single-phase solution for the construction of semi-flexible paving layers to be used as alternative material to common concrete and bituminous layers is experimented and introduced, aiming the production and laying of a single-phase laid material instead of a traditional two phases grouted macadam. Finally, on a parallel research work for farming pavements, the possible use of common geotechnical anti-erosive products for the improvement of soil bearing capacity of paddock areas in cattle husbandries of bio-farms is evaluated. this thesis has clearly demonstrated the feasibility of using the sustainable recycled aggregates for low-traffic rural roads and the pavements of farming and agriculture areas. The pavement layers constructed with recycled aggregates provided satisfying performance under heavy traffic conditions in experimental pavements. This, together with the fact that these aggregates can be available in most areas and in large quantities, provides great impetus towards shifting from traditional materials to more sustainable alternatives. The chemical and environmental stability of these materials proves their soundness to be utilized in farming environments.

Vulnerable users' protection with advanced recycling paving materials. Design and characterisation of rubber-based impact-absorbing pavement materials for bike lanes and sidewalks

Our cities are constantly evolving, and the necessity to improve the condition and safety of the urban infrastructures is fundamental. However, on the roads, the specific needs of cyclists and pedestrians are often neglected. The Vulnerable Road Users (VRUs), among whom cyclists and pedestrians are, rarely benefit from the most innovative safety measures. Inspired by playgrounds and aiming to reduce VRUs injuries, the Impact-Absorbing Pavements (IAP) developed as novel sidewalks, and bike lanes surface layers may help decrease injuries, fatalities, and the related societal costs. To achieve this goal, the End-of-Life Tyres (ELTs) crumb rubber (CR) is used as a primary resource, bringing its elastic properties into the surface layer. The thesis is divided into five main chapters. The first concerns the formulation and the definition of a feasible mix. The second explores the mechanical and environmental properties in detail, and the ageing effect is also assessed. The third describes the modelling of the material to simulate accidents and measure the injury reduction, especially on the head. The fourth chapter is reserved for the field trial. The last gives some perspectives on the research and proposes a way to optimize and improve the data and results collected during the doctoral research. It was observed that the specimens made with cold protocol have noticeable performances and reduce the overall carbon footprint impact of this material. The material modelling and the accident simulation proved the performance of the IAP against head injuries, and the field trial confirmed the good results obtained in the laboratory for the cold-made material. Finally, the outcomes of this thesis opened many prospective to the IAP development, such as the use of a plant-based binder or recycled aggregates and gave a positive prospect of an innovative material to the urban road infrastructures.

High friction and acoustic surface for pavements: development of artificial engineered aggregates from recycled powders

There is a constant need to improve the infrastructure's quality and build new infrastructure with better designs. The risk of accidents and noise can be reduced by improving the surface properties of the pavement. The amount of raw material used in road construction is worrisome, as it is finite and due the waste produced. Environmentally-friendly roads construction, recycling might be the main way. Projects must be more environmentally-friendly, safer, and quieter. Is it possible to develop a safer, quieter and environmentally-friendly pavement surfaces? The hypothesis is: is it possible to create an Artificial Engineered Aggregate (AEA) using waste materials and providing it with a specific shape that can help to reduce the noise and increase the friction? The thesis presents the development of an AEA and its application as a partial replacement in microsurfacing samples. The 1st introduces the topic and provides the aim and objectives of the thesis. The 2nd chapter – presents a pavement solution to noise and friction review. The 3rd chapter - developing a mix design for a geopolymer mortar that used basalt powder. The 4th chapter is presented the physical-mechanical evaluation of the AEA. The 5th chapter evaluates the use of this aggregate in microsurfacing regarding the texture parameters. The 6th chapter, those parameter are used as an input to SPERoN® model, simulating their noise behavior of these solutions. The findings from this thesis are presented as partial conclusions in each chapter, to be closed in a final chapter. The main findings are: the DoE provided the tool to select the appropriate geopolymer mortar mix design; AEA had interesting results regarding the physical-mechanical tests; AEA in partial replacement of the natural aggregates in microsurfacing mixture proved feasible. The texture parameters and noise levels obtained in AEA samples demonstrate that it can serve as a HIFASP

Multiscale modeling of light-harvesting systems based on rhodamine B aggregates

Rhodamine B (RB) has been successfully exploited in the synthesis of light harvesting systems, but since RB is prone to form dimers acting as quenchers for the fluorescence, high energy transfer efficiencies can be reached only when using bulky and hydrophobic counterions acting as spacers between RBs. In this PhD thesis, a multiscale theoretical study aimed at providing insights into the structural, photophysical and optical properties of RB and its aggregates is presented. At the macroscopic level (no atomistic details) a phenomenological model describing the fluorescence decay of RB networks in presence of both quenching from dimers and exciton-exciton annihiliation is presented and analysed, showing that the quenching from dimers affects the decay only at long times, a feature that can be exploited in global fitting analysis to determine relevant chemical and photophysical information. At the mesoscopic level (atomistic details but no electronic structure) the RB aggregation in water in presence of different counterions is studied with molecular dynamics (MD) simulations. A new force field has been parametrized for describing the RB flexibility and the RB-RB interaction driving the dimerization. Simulations correctly predict the RB/counterion aggregation only in presence of bulky and hydrophobic counterion and its ability to prevent the dimerization. Finally, at the microscopic level, DFT calculations are performed to demonstrate the spacing action of bulky counterions, but standard TDDFT calculations are showed to fail in correctly describing the excited states of RB and its dimers. Moreover, also standard procedures proposed in literature for obtaining ad hoc functionals are showed to not work properly. A detailed analysis on the effect of the exact exchange shows that its short-range contribution is the crucial quantity for ameliorating results, and a new functional containing a proper amount of such an exchange is proposed and successfully tested.