Analisi degli aspetti di qualità nella gestione dei sistemi di drenaggio urbano attraverso modellazione numerica e indagini di campo

In order to protect river water quality, highly affected in urban areas by continuos as intermittent immissions, it is necessary to adopt measures to intercept and treat these polluted flows. In particular during rain events, river water quality is affected by CSOs activation. Built in order to protect the sewer system and the WWTP by increased flows due to heavy rains, CSOs divert excess flows to the receiving water body. On the basis of several scientific papers, and of direct evidences as well, that demonstrate the detrimental effect of CSOs discharges, also the legislative framework moved towards a stream standard point of view. The WFD (EU/69/2000) sets new goals for receiving water quality, and groundwater as well, through an integrated immission/emissions phylosophy, in which emission limits are associated with effluent standards, based on the receiving water characteristics and their specific use. For surface waters the objective is that of a “good” ecological and chemical quality status. A surface water is defined as of good ecological quality if there is only slight departure from the biological community that would be expected in conditions of minimal anthropogenic impact. Each Member State authority is responsible for preparing and implementing a River Basin Management Plan to achieve the good ecological quality, and comply with WFD requirements. In order to cope with WFD targets, and thus to improve urban receiving water quality, a CSOs control strategy need to be implemented. Temporarily storing the overflow (or at least part of it) into tanks and treating it in the WWTP, after the end of the storm, showed good results in reducing total pollutant mass spilled into the receiving river. Italian State Authority, in order to comply with WFD statements, sets general framework, and each Region has to adopt a Water Remediation Plan (PTA, Piano Tutela Acque), setting goals, methods, and terms, to improve river water quality. Emilia Romagna PTA sets 25% reduction up to 2008, and 50% reduction up to 2015 fo total pollutants masses delivered by CSOs spills. In order to plan remediation actions, a deep insight into spills dynamics is thus of great importance. The present thesis tries to understand spills dynamics through a numerical and an experimental approach. A four months monitoring and sampling campaign was set on the Bologna sewer network, and on the Navile Channel, that is the WWTP receiving water , and that receives flows from up to 28 CSOs during rain events. On the other hand, the full model of the sewer network, was build with the commercial software InfoWorks CS. The model was either calibrated with the data from the monitoring and sampling campaign. Through further model simulations interdependencies among masses spilled, rain characteristics and basin characteristics are looked for. The thesis can be seen as a basis for further insighs and for planning remediation actions.

Modello bayesiano per la riduzione dell'incertezza nella previsione delle piene del fiume Reno

Many efforts have been devoting since last years to reduce uncertainty in hydrological modeling predictions. The principal sources of uncertainty are provided by input errors, for inaccurate rainfall prediction, and model errors, given by the approximation with which the water flow processes in the soil and river discharges are described. The aim of the present work is to develop a bayesian model in order to reduce the uncertainty in the discharge predictions for the Reno river. The ’a priori’ distribution function is given by an autoregressive model, while the likelihood function is provided by a linear equation which relates observed values of discharge in the past and hydrological TOPKAPI model predictions obtained by the rainfall predictions of the limited-area model COSMO-LAMI. The ’a posteriori’ estimations are provided throw a H∞ filter, because the statistical properties of estimation errors are not known. In this work a stationary and a dual adaptive filter are implemented and compared. Statistical analysis of estimation errors and the description of three case studies of flood events occurred during the fall seasons from 2003 to 2005 are reported. Results have also revealed that errors can be described as a markovian process only at a first approximation. For the same period, an ensemble of ’a posteriori’ estimations is obtained throw the COSMO-LEPS rainfall predictions, but the spread of this ’a posteriori’ ensemble is not enable to encompass observation variability. This fact is related to the building of the meteorological ensemble, whose spread reaches its maximum after 5 days. In the future the use of a new ensemble, COSMO–SREPS, focused on the first 3 days, could be helpful to enlarge the meteorogical and, consequently, the hydrological variability.

Reaching to a target in the 3-D space

Reaching and grasping an object is an action that can be performed in light, under visual guidance, as well as in darkness, under proprioceptive control only. Area V6A is a visuomotor area involved in the control of reaching movements. V6A, besides neurons activated by the execution of reaching movements, shows passive somatosensory and visual responses. This suggests fro V6A a multimodal capability of integrating sensory and motor-related information, We wanted to know whether this integration occurrs in reaching movements and in the present study we tested whether the visual feedback influenced the reaching activity of V6A neurons. In order to better address this question, we wanted to interpret the neural data in the light of the kinematic of reaching performance. We used an experimental paradigm that could examine V6A responses in two different visual backgrounds, light and dark. In these conditions, the monkey performed an istructed-delay reaching task moving the hand towards different target positions located in the peripersonal space. During the execution of reaching task, the visual feedback is processed in a variety of patterns of modulation, sometimes not expected. In fact, having already demonstrated in V6A reach-related discharges in absence of visual feedback, we expected two types of neural modulation: 1) the addition of light in the environment enhanced reach-related discharges recorded in the dark; 2) the light left the neural response unmodified. Unexpectedly, the results show a complex pattern of modulation that argues against a simple additive interaction between visual and motor-related signals.

Development of oil spill detection techniques for satellite optical sensors and their application to monitor oil spill discharge in Mediterranean sea

Satellite remote sensing has proved to be an effective support in timely detection and monitoring of marine oil pollution, mainly due to illegal ship discharges. In this context, we have developed a new methodology and technique for optical oil spill detection, which make use of MODIS L2 and MERIS L1B satellite top of atmosphere (TOA) reflectance imagery, for the first time in a highly automated way. The main idea was combining wide swaths and short revisit times of optical sensors with SAR observations, generally used in oil spill monitoring. This arises from the necessity to overcome the SAR reduced coverage and long revisit time of the monitoring area. This can be done now, given the MODIS and MERIS higher spatial resolution with respect to older sensors (250-300 m vs. 1 km), which consents the identification of smaller spills deriving from illicit discharge at sea. The procedure to obtain identifiable spills in optical reflectance images involves removal of oceanic and atmospheric natural variability, in order to enhance oil-water contrast; image clustering, which purpose is to segment the oil spill eventually presents in the image; finally, the application of a set of criteria for the elimination of those features which look like spills (look-alikes). The final result is a classification of oil spill candidate regions by means of a score based on the above criteria.

Variabilità spaziale dei parametri di modelli afflussi-deflussi

L’invarianza spaziale dei parametri di un modello afflussi-deflussi può rivelarsi una soluzione pratica e valida nel caso si voglia stimare la disponibilità di risorsa idrica di un’area. La simulazione idrologica è infatti uno strumento molto adottato ma presenta alcune criticità legate soprattutto alla necessità di calibrare i parametri del modello. Se si opta per l’applicazione di modelli spazialmente distribuiti, utili perché in grado di rendere conto della variabilità spaziale dei fenomeni che concorrono alla formazione di deflusso, il problema è solitamente legato all’alto numero di parametri in gioco. Assumendo che alcuni di questi siano omogenei nello spazio, dunque presentino lo stesso valore sui diversi bacini, è possibile ridurre il numero complessivo dei parametri che necessitano della calibrazione. Si verifica su base statistica questa assunzione, ricorrendo alla stima dell’incertezza parametrica valutata per mezzo di un algoritmo MCMC. Si nota che le distribuzioni dei parametri risultano in diversa misura compatibili sui bacini considerati. Quando poi l’obiettivo è la stima della disponibilità di risorsa idrica di bacini non strumentati, l’ipotesi di invarianza dei parametri assume ancora più importanza; solitamente infatti si affronta questo problema ricorrendo a lunghe analisi di regionalizzazione dei parametri. In questa sede invece si propone una procedura di cross-calibrazione che viene realizzata adottando le informazioni provenienti dai bacini strumentati più simili al sito di interesse. Si vuole raggiungere cioè un giusto compromesso tra lo svantaggio derivante dall’assumere i parametri del modello costanti sui bacini strumentati e il beneficio legato all’introduzione, passo dopo passo, di nuove e importanti informazioni derivanti dai bacini strumentati coinvolti nell’analisi. I risultati dimostrano l’utilità della metodologia proposta; si vede infatti che, in fase di validazione sul bacino considerato non strumentato, è possibile raggiungere un buona concordanza tra le serie di portata simulate e osservate.

Fabrication, Electrical Characterization and Simulation of Thin Film Solar Cells: CdTe and CIGS Materials

CdTe and Cu(In,Ga)Se2 (CIGS) thin film solar cells are fabricated, electrically characterized and modelled in this thesis. We start from the fabrication of CdTe thin film devices where the R.F. magnetron sputtering system is used to deposit the CdS/CdTe based solar cells. The chlorine post-growth treatment is modified in order to uniformly cover the cell surface and reduce the probability of pinholes and shunting pathways creation which, in turn, reduces the series resistance. The deionized water etching is proposed, for the first time, as the simplest solution to optimize the effect of shunt resistance, stability and metal-semiconductor inter-diffusion at the back contact. In continue, oxygen incorporation is proposed while CdTe layer deposition. This technique has been rarely examined through R.F sputtering deposition of such devices. The above experiments are characterized electrically and optically by current-voltage characterization, scanning electron microscopy, x-ray diffraction and optical spectroscopy. Furthermore, for the first time, the degradation rate of CdTe devices over time is numerically simulated through AMPS and SCAPS simulators. It is proposed that the instability of electrical parameters is coupled with the material properties and external stresses (bias, temperature and illumination). Then, CIGS materials are simulated and characterized by several techniques such as surface photovoltage spectroscopy is used (as a novel idea) to extract the band gap of graded band gap CIGS layers, surface or bulk defect states. The surface roughness is scanned by atomic force microscopy on nanometre scale to obtain the surface topography of the film. The modified equivalent circuits are proposed and the band gap graded profiles are simulated by AMPS simulator and several graded profiles are examined in order to optimize their thickness, grading strength and electrical parameters. Furthermore, the transport mechanisms and Auger generation phenomenon are modelled in CIGS devices.

Stima dei parametri di modelli idrologici mediante ottimizzazione dell’utilità

Tradizionalmente, l'obiettivo della calibrazione di un modello afflussi-deflussi è sempre stato quello di ottenere un set di parametri (o una distribuzione di probabilità dei parametri) che massimizzasse l'adattamento dei dati simulati alla realtà osservata, trattando parzialmente le finalità applicative del modello. Nel lavoro di tesi viene proposta una metodologia di calibrazione che trae spunto dell'evidenza che non sempre la corrispondenza tra dati osservati e simulati rappresenti il criterio più appropriato per calibrare un modello idrologico. Ai fini applicativi infatti, può risultare maggiormente utile una miglior rappresentazione di un determinato aspetto dell'idrogramma piuttosto che un altro. Il metodo di calibrazione che viene proposto mira a valutare le prestazioni del modello stimandone l'utilità nell'applicazione prevista. Tramite l'utilizzo di opportune funzioni, ad ogni passo temporale viene valutata l'utilità della simulazione ottenuta. La calibrazione viene quindi eseguita attraverso la massimizzazione di una funzione obiettivo costituita dalla somma delle utilità stimate nei singoli passi temporali. Le analisi mostrano come attraverso l'impiego di tali funzioni obiettivo sia possibile migliorare le prestazioni del modello laddove ritenute di maggior interesse per per le finalità applicative previste.

The posterior parietal cortex: a bridge between vision and action

The present work takes into account three posterior parietal areas, V6, V6A, and PEc, all operating on different subsets of signals (visual, somatic, motor). The work focuses on the study of their functional properties, to better understand their respective contribution in the neuronal circuits that make possible the interactions between subject and external environment. In the caudalmost pole of parietal lobe there is area V6. Functional data suggest that this area is related to the encoding of both objects motion and ego-motion. However, the sensitivity of V6 neurons to optic flow stimulations has been tested only in human fMRI experiments. Here we addressed this issue by applying on monkey the same experimental protocol used in human studies. The visual stimulation obtained with the Flow Fields stimulus was the most effective and powerful to activate area V6 in monkey, further strengthening this homology between the two primates. The neighboring areas, V6A and PEc, show different cytoarchitecture and connectivity profiles, but are both involved in the control of reaches. We studied the sensory responses present in these areas, and directly compared these.. We also studied the motor related discharges of PEc neurons during reaching movements in 3D space comparing also the direction and depth tuning of PEc cells with those of V6A. The results show that area PEc and V6A share several functional properties. Area PEc, unlike V6A, contains a richer and more complex somatosensory input, and a poorer, although complex visual one. Differences emerged also comparing the motor-related properties for reaches in depth: the incidence of depth modulations in PEc and the temporal pattern of modulation for depth and direction allow to delineate a trend among the two parietal visuomotor areas.

Modelling, diagnostics and experimental analysis of plasma assisted processes for material treatment

This work presents results from experimental investigations of several different atmospheric pressure plasmas applications, such as Metal Inert Gas (MIG) welding and Plasma Arc Cutting (PAC) and Welding (PAW) sources, as well as Inductively Coupled Plasma (ICP) torches. The main diagnostic tool that has been used is High Speed Imaging (HSI), often assisted by Schlieren imaging to analyse non-visible phenomena. Furthermore, starting from thermo-fluid-dynamic models developed by the University of Bologna group, such plasma processes have been studied also with new advanced models, focusing for instance on the interaction between a melting metal wire and a plasma, or considering non-equilibrium phenomena for diagnostics of plasma arcs. Additionally, the experimental diagnostic tools that have been developed for industrial thermal plasmas have been used also for the characterization of innovative low temperature atmospheric pressure non equilibrium plasmas, such as dielectric barrier discharges (DBD) and Plasma Jets. These sources are controlled by few kV voltage pulses with pulse rise time of few nanoseconds to avoid the formation of a plasma arc, with interesting applications in surface functionalization of thermosensitive materials. In order to investigate also bio-medical applications of thermal plasma, a self-developed quenching device has been connected to an ICP torch. Such device has allowed inactivation of several kinds of bacteria spread on petri dishes, by keeping the substrate temperature lower than 40 degrees, which is a strict requirement in order to allow the treatment of living tissues.