Biofilms on exposed monumental stones: mechanism of formation and development of new control methods

Within the stone monumental artefacts artistic fountains are extremely favorable to formation of biofilms, giving rise to biodegradation processes related with physical-chemical and visual aspect alterations, because of their particular exposure conditions. Microbial diversity of five fountains (two from Spain and three from Italy) was investigated. It was observed an ample similarity between the biodiversity of monumental stones reported in literature and that one found in studied fountains. Mechanical procedures and toxic chemical products are usually employed to remove such phototrophic patinas. Alternative methods based on natural antifouling substances are recently experimented in the marine sector, due to their very low environmental impact and for the bio settlement prevention on partially immersed structures of ships. In the present work groups of antibiofouling agents (ABAs) were selected from literature for their ability to interfere, at molecular level, with the microbial communication system “quorum sensing”, inhibiting the initial phase of biofilm formation. The efficacy of some natural antibiofoulants agents (ABAs) with terrestrial (Capsaicine - CS, Cinnamaldehyde - CI) and marine origin (Zosteric Acid - ZA, poly-Alkyl Pyridinium Salts – pAPS and Ceramium botryocarpum extract - CBE), incorporated into two commercial coatings (Silres BS OH 100 - S and Wacker Silres BS 290 - W) commonly used in stone conservation procedures were evaluated. The formation of phototrophic biofilms in laboratory conditions (on Carrara marble specimens and Sierra Elvira stone) and on two monumental fountains (Tacca’s Fountain 2 - Florence, Italy and Fountain from Patio de la Lindaraja - Alhambra Palace, Granada, Spain) has been investigated in the presence or absence of these natural antifouling agents. The natural antibiofouling agents, at tested concentrations, demonstrated a certain inhibitory effect. The silane-siloxane based silicone coating (W) mixing with ABAs was more suitable with respect to ethyl silicate coating (S) and proved efficacy against biofilm formation only when incompletely cured. The laboratory results indicated a positive action in inhibiting the patina formation, especially for poly-alkyl pyridinium salts, zosteric acid and cinnamaldehyde, while on site tests revealed a good effect for zosteric acid.

Study of materials and technology of ancient floor mosaics' substrate

Ancient pavements are composed of a variety of preparatory or foundation layers constituting the substrate, and of a layer of tesserae, pebbles or marble slabs forming the surface of the floor. In other cases, the surface consists of a mortar layer beaten and polished. The term mosaic is associated with the presence of tesserae or pebbles, while the more general term pavement is used in all the cases. As past and modern excavations of ancient pavements demonstrated, all pavements do not necessarily display the stratigraphy of the substrate described in the ancient literary sources. In fact, the number and thickness of the preparatory layers, as well as the nature and the properties of their constituent materials, are often varying in pavements which are placed either in different sites or in different buildings within a same site or even in a same building. For such a reason, an investigation that takes account of the whole structure of the pavement is important when studying the archaeological context of the site where it is placed, when designing materials to be used for its maintenance and restoration, when documenting it and when presenting it to public. Five case studies represented by archaeological sites containing floor mosaics and other kind of pavements, dated to the Hellenistic and the Roman period, have been investigated by means of in situ and laboratory analyses. The results indicated that the characteristics of the studied pavements, namely the number and the thickness of the preparatory layers, and the properties of the mortars constituting them, vary according to the ancient use of the room where the pavements are placed and to the type of surface upon which they were built. The study contributed to the understanding of the function and the technology of the pavements’ substrate and to the characterization of its constituent materials. Furthermore, the research underlined the importance of the investigation of the whole structure of the pavement, included the foundation surface, in the interpretation of the archaeological context where it is located. A series of practical applications of the results of the research, in the designing of repair mortars for pavements, in the documentation of ancient pavements in the conservation practice, and in the presentation to public in situ and in museums of ancient pavements, have been suggested.

Study of the building and decorative materials and techniques used in Hungarian Roman sites

The aims of this research were: - To identify the characteristics, properties and provenance of the building and decorative material found in three Hungarian Roman sites: Nagyharsány, Nemesvámos-Balácapuszta and Aquincum - To provide a database of information on the different sites - To have an overview of main conservation strategies applied in Hungary. Geological studies, macroscopical and microscopical observations, XRD investigations, physical and chemical analyses allowed us to define the characteristics and properties of the different kinds of collected materials. Building stones sampled from Nagyharsány site showed two different kinds of massive limestone belonging to the areas surrounding the villa. Also Building stones sampled from Nemesvámos-Balácapuszta Roman villa proved to be compatible with limestone belonging to local sources. Mural painting fragments show that all samples are units composed of multilayered structures. Mosaic tesserae can be classified as following: -Pale yellow , blackish and pink tesserae are comparable with local limestone; -White tessera, composed of marble, was probably imported from distant regions of the Empire, as the usual practice of Romans. Mortars present different characteristics according to the age, the site and the functions: -Building mortars are generally lime based, white or pale yellow in colour, present a high percentage of aggregates represented by fine sand; -Supporting mortars from both mosaics and mural paintings are reddish or pinkish in colour, due to the presence of high percentage of brick dust and tiles fragments, and present a higher content of MgO. Although the condition of the sites, there is an insignificant content of soluble salts. Database The whole study has allowed us to provide work sheets for each samples, including all characteristics and properties. Furthermore, all sites included in the frame of the research have been described and illustrated on the base of their floor plans, material and construction methodologies. It can be concluded that: 1. In Nagyharsány Archaeological site, it is possible to define a sequence of different construction phases on the base of the study of building material and mortars. The results are comparable with the chronology of the site provided by the archaeologists 2. The material used for construction was of local origin while the more precious ones, used for decorative elements, were probably imported from long distance 3. Construction techniques in Hungary mainly refer to the usual Roman knowledge and practice (Vitruvius); few differences have been found 4. The database will represent an archive for Archaeologists, Historians and Conservators dealing with Roman period in Hungary.

Durability of crystalline monumental stones in terms of their petrophysical characteristics

The durability of stone building materials is an issue of utmost importance in the field of monument conservation. In order to be able to preserve our built cultural heritage, the thorough knowledge of its constituent materials and the understanding of the processes that affect them are indispensable. The main objective of this research was to evaluate the durability of a special stone type, the crystalline stones, in correlation with their intrinsic characteristics, the petrophysical properties. The crystalline stones are differentiated from the cemented stones on the basis of textural features. Their most important specific property is the usually low, fissure-like porosity. Stone types of significant monumental importance, like the marble or granite belong to this group. The selected materials for this investigation, indeed, are a marble (Macael marble, Spain) and a granite (Silvestre Vilachán granite, Spain). In addition, an andesite (Szob andesite, Hungary) also of significant monumental importance was selected. This way a wide range of crystalline rocks is covered in terms of petrogenesis: stones of metamorphic, magmatic and volcanic origin, which can be of importance in terms of mineralogical, petrological or physical characteristics. After the detailed characterization of the petrophysical properties of the selected stones, their durability was assessed by means of artificial ageing. The applied ageing tests were: the salt crystallization, the frost resistance in pure water and in the presence of soluble salts, the salt mist and the action of SO2 in the presence of humidity. The research aimed at the understanding of the mechanisms of each weathering process and at finding the petrophysical properties most decisive in the degradation of these materials. Among the several weathering mechanisms, the most important ones were found to be the physical stress due to crystallization pressure of both salt and ice, the thermal fatigue due to cyclic temperature changes and the chemical reactions (mostly the acidic attack) between the mineral phases and the external fluids. The properties that fundamentally control the degradation processes, and thus the durability of stones were found to be: the mineralogical and chemical composition; the hydraulic properties especially the water uptake, the permeability and the drying; the void space structure, especially the void size and aperture size distribution and the connectivity of the porous space; and the thermal and mechanical properties. Because of the complexity of the processes and the high number of determining properties, no mechanisms or characteristics could be identified as typical for crystalline stones. The durability or alterability of each stone type must be assessed according to its properties and not according to the textural or petrophysical classification they belong to. Finally, a critical review of standardized methods is presented, based on which an attempt was made for recommendations of the most adequate methodology for the characterization and durability assessment of crystalline stones.

Thermochronologic and geodynamic evolution of the Pontides: Sakarya terrane (Karakaya Complex) and Istanbul terrane, Turkey.

An integrated array of analytical methods -including clay mineralogy, vitrinite reflectance, Raman spectroscopy on carbonaceous material, and apatite fission-track analysis- was employed to constrain the thermal and thermochronological evolution of selected portions of the Pontides of northern Turkey. (1) A multimethod investigation was applied for the first time to characterise the thermal history of the Karakaya Complex, a Permo-Triassic subduction-accretion complex cropping out throughout the Sakarya Zone. The results indicate two different thermal regimes: the Lower Karakaya Complex (Nilüfer Unit) -mostly made of metabasite and marble- suffered peak temperatures of 300-500°C (greenschist facies); the Upper Karakaya Complex (Hodul and the Orhanlar Units) –mostly made of greywacke and arkose- yielded heterogeneous peak temperatures (125-376°C), possibly the result of different degree of involvement of the units in the complex dynamic processes of the accretionary wedge. Contrary to common belief, the results of this study indicate that the entire Karakaya Complex suffered metamorphic conditions. Moreover, a good degree of correlation among the results of these methods demonstrate that Raman spectroscopy on carbonaceous material can be applied successfully to temperature ranges of 200-330°C, thus extending the application of this method from higher grade metamorphic contexts to lower grade metamorphic conditions. (2) Apatite fission-track analysis was applied to the Sakarya and the İstanbul Zones in order to constrain the exhumation history and timing of amalgamation of these two exotic terranes. AFT ages from the İstanbul and Sakarya terranes recorded three distinct episodes of exhumation related to the complex tectonic evolution of the Pontides. (i) Paleocene - early Eocene ages (62.3-50.3 Ma) reflect the closure of the İzmir-Ankara ocean and the ensuing collision between the Sakarya terrane and the Anatolide-Tauride Block. (ii) Late Eocene - earliest Oligocene (43.5-32.3 Ma) ages reflect renewed tectonic activity along the İzmir-Ankara. (iii) Late Oligocene- Early Miocene ages reflect the onset and development of the northern Aegean extension. The consistency of AFT ages, both north and south of the tectonic contact between the İstanbul and Sakarya terranes, suggest that such terranes were amalgamated in pre-Cenozoic times. (3) Fission-track analysis was also applied to rock samples from the Marmara region, in an attempt to constrain the inception and development of the North Anatolian Fault system in the region. The results agree with those from the central Pontides. The youngest AFT ages (Late Oligocene - early Miocene) were recorded in the western portion of the Marmara Sea region and reflect the onset and development of northern Aegean extension. Fission-track data from the eastern Marmara Sea region indicate rapid Early Eocene exhumation induced by the development of the İzmir-Ankara orogenic wedge. Thermochronological data along the trace of the Ganos Fault –a segment of the North Anatolian Fault system- indicate the presence of a tectonic discontinuity active by Late Oligocene time, i.e. well before the arrival of the North Anatolian Fault system in the area. The integration of thermochronologic data with preexisting structural data point to the existence of a system of major E-W-trending structural discontinuities active at least from the Late Oligocene. In the Early Pliocene, inception of the present-day North Anatolian Fault system in the Marmara region occurred by reactivation of these older tectonic structures. 


Problemi di consolidamento di matrici lapidee di differente microstruttura esposte a sollecitazioni ambientali e microclimatiche di varia origine

Questa ricerca presenta i risultati di una indagine volta a verificare la reale efficacia di rinforzo corticale su rocce carbonatiche di differenti caratteristiche mineralogiche, utilizzando consolidanti inorganici in soluzione acquosa quali l’Ossalato Ammonico (AmOX) e il Diammonio Fosfato Acido (DAHP). Le matrici carbonatiche scelte sono quelle del marmo invecchiato e una biomicrite. Sui campioni sono state effettuate indagini (SEM,MIP,XRD,MO,TG-DTA) di caratterizzazione prima e dopo i trattamenti volte a valutare eventuali effetti di rinforzo e misure fisiche di suscettività all’acqua. L’efficacia dei consolidanti inorganici è stata comparata con diversi consolidanti organici e ibridi presenti in commercio ed utilizzati in ambito conservativo. L'efficacia si è mostrata fortemente legata al fabric del materiale e alle modalità di strutturazione del prodotto di neomineralizzazione all’interno della compagine deteriorata. Nel caso del trattamento con AmOx il soluzione acquosa al 4%, la whewellite è l’unica fase di neoformazione riscontrata; la sua crescita avviene con un meccanismo essenzialmente topochimico. Nei materiali carbonatici compatti si possono ottenere solo modesti spessori di coating di neoformazione; per le rocce porose, contenenti difetti come lesioni, pori o micro-fratture, l’efficacia del trattamento può risultare più incisiva. Questo trattamento presenta lo svantaggio legato alla rapidissima formazione dei cristalli di whewellite che tendono a passivare le superfici impedendo la progressione della reazione; il vantaggio è connesso alla facile applicazione in cantiere. Nel caso del DAHP sulla matrice carbonatica trattata, si formano cluster cristallini contenenti specie più o meno stabili alcune riconducibili all’idrossiapatite. La quantità e qualità delle fasi, varia fortemente in funzione della temperatura, pH, pressione con conseguenze interferenza nelle modalità di accrescimento dei cristalli. Il trattamento alla stato attuale appare comunque di notevole interesse ma allo stesso tempo difficilmente applicabile e controllabile nelle reali condizioni operative di un cantiere di restauro.

Per un'archeologia del lavoro in eta' protobizantina. Organizzazione e committenza del cantiere edilizio attraverso i marchi dei marmorari

La ricerca riguarda lo studio del cantiere edilizio protobizantino, con particolare riferimento al ciclo della lavorazione del marmo. Quest’ultimo viene analizzato sotto il profilo amministrativo, tecnico, sociale ed artigianale. L’elemento guida della ricerca sono i marchi dei marmorari, sigle apposte da funzionari e maestranze durante il processo produttivo. Dapprima, fonti letterarie ed epigrafiche, tra cui le sigle di cava e officina su marmo, vengono esaminate per ricostruire il sistema alto-imperiale di amministrazione delle cave e di gestione dei flussi marmorei, nonché l’iter tecnico-artigianale adottato per la produzione dei manufatti. Il confronto con i dati disponibili per la tarda antichità, con particolare riferimento alle cave di Proconneso, evidenzia una sostanziale continuità della prassi burocratico-amministrativa, mentre alcuni cambiamenti si riscontrano nell’ambito produttivo-artigianale. Il funzionamento degli atelier marmorari viene approfondito attraverso lo studio dei marchi dei marmorari. Si tratta di caratteri greci singoli, multipli o monogrammi. Una ricognizione sistematica delle sigle dalla pars Orientalis dell’impero, reperite in bibliografia o da ricognizioni autoptiche, ha portato alla raccolta di circa 2360 attestazioni. Per esse si propone una classificazione tipologica tra sigle di cava, stoccaggio, officina. Tra le sigle di cava si annoverano sigle di controllo, destinazione/committenza, assemblaggio/posizionamento. Una particolare attenzione è riservata alle sigle di officina, riferibili ad un nome proprio di persona, ovvero al πρωτομαΐστωρ, il capo-bottega che supervisionava il lavoro dei propri artigiani e fungeva da garante del prodotto consegnato alla committenza. Attraverso lo studio comparato delle sigle reperite a Costantinopoli e in altri contesti si mette in luce la prassi operativa adottata dagli atelier nei processi di manifattura, affrontando anche il problema delle maestranze itineranti. Infine, sono analizzate fonti scritte di varia natura per poter collocare il fenomeno del marmo in un contesto socio-economico più ampio, con particolare riferimento alle figure professionali ed artigianali coinvolte nei cantieri e al problema della committenza.