Use of essential oils and biocontrol cultures for the improvement of shelf-life of fresh cut products

The demand of minimally processed fruits and vegetables has increased in the last years. However, their intrinsic characteristics may favor the growth of pathogens and spoilage microbiota. The negative effects on human health reported for some traditional chemical sanitizers have justified the search for substitutes to guarantee food safety and quality. In this work we have evaluate the potential of some essential oils and their components to improve the safety and the shelf life of Lamb’s lettuce (Valerianella locusta) and apples (Golden delicious). Moreover, the effects of selected lactic acid bacteria alone or in combination with essential oils or their components, on the shelf-life and safety as well as organoleptic properties of minimally processed products, were evaluated. Since the lack of knowledge of microbial cell targets of essential oils represent one of the most important limit to the use of these molecules at industrial level, another aim of this thesis was the study of the action mechanisms of essential oils and their components. The results obtained showed the beneficial effects of the natural antimicrobials as well as the selected lactic acid bacteria on minimally processed fruit and vegetable safety and shelf-life, without detrimental effects on the quality parameters. The beneficial effects obtained by the use of the selected biocontrol agents were further increased combining them with selected natural antimicrobials. The natural antimicrobial employed induced noticeable modifications of membrane fatty acid profiles and volatile compounds produced by microbial cells during the growth. The modification of the expression in genes involved in fatty acid biosynthesis suggesting that the cytoplasmic membrane of microbial cells is one of the major cellular target of essential oils and their components. The comprehension of microbial stress response mechanisms can contribute to the scaling up of natural antimicrobials and bio-control agents at industrial level.

New functional and biomechanical assessments for the improvement of the surgical navigation systems for joint replacement in the human lower limb

In case of severe osteoarthritis at the knee causing pain, deformity, and loss of stability and mobility, the clinicians consider that the substitution of these surfaces by means of joint prostheses. The objectives to be pursued by this surgery are: complete pain elimination, restoration of the normal physiological mobility and joint stability, correction of all deformities and, thus, of limping. The knee surgical navigation systems have bee developed in computer-aided surgery in order to improve the surgical final outcome in total knee arthroplasty. These systems provide the surgeon with quantitative and real-time information about each surgical action, like bone cut executions and prosthesis component alignment, by mean of tracking tools rigidly fixed onto the femur and the tibia. Nevertheless, there is still a margin of error due to the incorrect surgical procedures and to the still limited number of kinematic information provided by the current systems. Particularly, patello-femoral joint kinematics is not considered in knee surgical navigation. It is also unclear and, thus, a source of misunderstanding, what the most appropriate methodology is to study the patellar motion. In addition, also the knee ligamentous apparatus is superficially considered in navigated total knee arthroplasty, without taking into account how their physiological behavior is altered by this surgery. The aim of the present research work was to provide new functional and biomechanical assessments for the improvement of the surgical navigation systems for joint replacement in the human lower limb. This was mainly realized by means of the identification and development of new techniques that allow a thorough comprehension of the functioning of the knee joint, with particular attention to the patello-femoral joint and to the main knee soft tissues. A knee surgical navigation system with active markers was used in all research activities presented in this research work. Particularly, preliminary test were performed in order to assess the system accuracy and the robustness of a number of navigation procedures. Four studies were performed in-vivo on patients requiring total knee arthroplasty and randomly implanted by means of traditional and navigated procedures in order to check for the real efficacy of the latter with respect to the former. In order to cope with assessment of patello-femoral joint kinematics in the intact and replaced knees, twenty in-vitro tests were performed by using a prototypal tracking tool also for the patella. In addition to standard anatomical and articular recommendations, original proposals for defining the patellar anatomical-based reference frame and for studying the patello-femoral joint kinematics were reported and used in these tests. These definitions were applied to two further in-vitro tests in which, for the first time, also the implant of patellar component insert was fully navigated. In addition, an original technique to analyze the main knee soft tissues by means of anatomical-based fiber mappings was also reported and used in the same tests. The preliminary instrumental tests revealed a system accuracy within the millimeter and a good inter- and intra-observer repeatability in defining all anatomical reference frames. In in-vivo studies, the general alignments of femoral and tibial prosthesis components and of the lower limb mechanical axis, as measured on radiographs, was more satisfactory, i.e. within ±3°, in those patient in which total knee arthroplasty was performed by navigated procedures. As for in-vitro tests, consistent patello-femoral joint kinematic patterns were observed over specimens throughout the knee flexion arc. Generally, the physiological intact knee patellar motion was not restored after the implant. This restoration was successfully achieved in the two further tests where all component implants, included the patellar insert, were fully navigated, i.e. by means of intra-operative assessment of also patellar component positioning and general tibio-femoral and patello-femoral joint assessment. The tests for assessing the behavior of the main knee ligaments revealed the complexity of the latter and the different functional roles played by the several sub-bundles compounding each ligament. Also in this case, total knee arthroplasty altered the physiological behavior of these knee soft tissues. These results reveal in-vitro the relevance and the feasibility of the applications of new techniques for accurate knee soft tissues monitoring, patellar tracking assessment and navigated patellar resurfacing intra-operatively in the contest of the most modern operative techniques. This present research work gives a contribution to the much controversial knowledge on the normal and replaced of knee kinematics by testing the reported new methodologies. The consistence of these results provides fundamental information for the comprehension and improvements of knee orthopedic treatments. In the future, the reported new techniques can be safely applied in-vivo and also adopted in other joint replacements.

Methodological improvement of 3D fluoroscopic analysis for the robust quantification of 3D kinematics of human joints

3D video-fluoroscopy is an accurate but cumbersome technique to estimate natural or prosthetic human joint kinematics. This dissertation proposes innovative methodologies to improve the 3D fluoroscopic analysis reliability and usability. Being based on direct radiographic imaging of the joint, and avoiding soft tissue artefact that limits the accuracy of skin marker based techniques, the fluoroscopic analysis has a potential accuracy of the order of mm/deg or better. It can provide fundamental informations for clinical and methodological applications, but, notwithstanding the number of methodological protocols proposed in the literature, time consuming user interaction is exploited to obtain consistent results. The user-dependency prevented a reliable quantification of the actual accuracy and precision of the methods, and, consequently, slowed down the translation to the clinical practice. The objective of the present work was to speed up this process introducing methodological improvements in the analysis. In the thesis, the fluoroscopic analysis was characterized in depth, in order to evaluate its pros and cons, and to provide reliable solutions to overcome its limitations. To this aim, an analytical approach was followed. The major sources of error were isolated with in-silico preliminary studies as: (a) geometric distortion and calibration errors, (b) 2D images and 3D models resolutions, (c) incorrect contour extraction, (d) bone model symmetries, (e) optimization algorithm limitations, (f) user errors. The effect of each criticality was quantified, and verified with an in-vivo preliminary study on the elbow joint. The dominant source of error was identified in the limited extent of the convergence domain for the local optimization algorithms, which forced the user to manually specify the starting pose for the estimating process. To solve this problem, two different approaches were followed: to increase the optimal pose convergence basin, the local approach used sequential alignments of the 6 degrees of freedom in order of sensitivity, or a geometrical feature-based estimation of the initial conditions for the optimization; the global approach used an unsupervised memetic algorithm to optimally explore the search domain. The performances of the technique were evaluated with a series of in-silico studies and validated in-vitro with a phantom based comparison with a radiostereometric gold-standard. The accuracy of the method is joint-dependent, and for the intact knee joint, the new unsupervised algorithm guaranteed a maximum error lower than 0.5 mm for in-plane translations, 10 mm for out-of-plane translation, and of 3 deg for rotations in a mono-planar setup; and lower than 0.5 mm for translations and 1 deg for rotations in a bi-planar setups. The bi-planar setup is best suited when accurate results are needed, such as for methodological research studies. The mono-planar analysis may be enough for clinical application when the analysis time and cost may be an issue. A further reduction of the user interaction was obtained for prosthetic joints kinematics. A mixed region-growing and level-set segmentation method was proposed and halved the analysis time, delegating the computational burden to the machine. In-silico and in-vivo studies demonstrated that the reliability of the new semiautomatic method was comparable to a user defined manual gold-standard. The improved fluoroscopic analysis was finally applied to a first in-vivo methodological study on the foot kinematics. Preliminary evaluations showed that the presented methodology represents a feasible gold-standard for the validation of skin marker based foot kinematics protocols.

Possibilities for the healthy and nutritional improvement of confectionery and sweet products.

The overall objective of this PhD was to investigate the possibility to increase the nutritional value of confectionary products by the use of natural ingredients with healthy functions. The first part of the thesis focused on the possible substitution of the most characteristic component of confectionary products, i.e. refined sugar. Many natural whole sweetening alternatives are available, though not widely used; the use of molasses, the byproduct of sugar beet and cane production, still rich in healthy components as minerals and phytochemicals is hereby discussed; after having verified molasses effectiveness in oxidative stress counteraction on liver cultured cells, the higher antioxidant capacity of a sweet food prepared with molasses instead of refined sugar was confirmed. A second step of the project dealt with another main ingredient of various sweet products, namely wheat. Particularly, the exploitation of soft and durum wheat byproducts could be another sustainable strategy to improve the healthy value of confectionery. The isolation of oligosaccharides with bioactive functions form different fractions of the wheat milling stream was studied and the new ingredients were shown to have a high dietary fiber and antioxidants content. As valid alternative, product developers should consider the appealing and healthy addition of ancient grains flour to sweet baked goods. The possibility of substituting the modern whole durum wheat with the ancient Kamut® khorasan was considered, and the antioxidant and anti-inflammatory effects of these grains were evaluated and compared both in vitro and in vivo on rats. Finally, since high consumption of confectionery is a risk factor for obesity, a possible strategy for the counteraction of this disease was investigated. The ability of three bioactives in inhibiting adipocytes differentiation was investigated. In fact, theoretically, compounds able to influence adipogenesis could be used in the formulation of functional sweet products and contribute to prevent obesity.

The synthesis of maleic anhydride: study of a new process and improvement of the industrial catalyst

Maleic anhydride is an important chemical intermediate mainly produced by the selective oxidation of n-butane, an industrial process catalyzed by vanadyl pyrophosphate-based materials, (VO)2P2O7. The first topic was investigated in collaboration with a company specialized in the production of organic anhydrides (Polynt SpA), with the aim of improving the performance of the process for the selective oxidation of n-butane to maleic anhydride, comparing the behavior of an industrial vanadyl pyrophosphate catalysts when utilized either in the industrial plant or in lab-scale reactor. The study was focused on how the catalyst characteristics and reactivity are affected by the reaction conditions and how the addition of a dopant can enhance the catalytic performance. Moreover, the ageing of the catalyst was studied, in order to correlate the deactivation process with the modifications occurring in the catalyst. The second topic was produced within the Seventh Framework (FP7) European Project “EuroBioRef”. The study was focused on a new route for the synthesis of maleic anhydride starting from an alternative reactant produced by fermentation of biomass:“bio-1-butanol”. In this field, the different possible catalytic configurations were investigated: the process was divided into two main reactions, the dehydration of 1-butanol to butenes and the selective oxidation of butenes to maleic anhydride. The features needed to catalyze the two steps were analyzed and different materials were proposed as catalysts, namely Keggin-type polyoxometalates, VOPO4∙2H2O and (VO)2P2O7. The reactivity of 1-butanol was tested under different conditions, in order to optimize the performance and understand the nature of the interaction between the alcohol and the catalyst surface. Then, the key intermediates in the mechanism of 1-butanol oxidehydration to MA were studied, with the aim of understanding the possible reaction mechanism. Lastly, the reactivity of the chemically sourced 1-butanol was compared with that one of different types of bio-butanols produced by biomass fermentation.

Improvement of photon transport model by including coupled photon-electron transport and kernel refinement

The first part of this work deals with the inverse problem solution in the X-ray spectroscopy field. An original strategy to solve the inverse problem by using the maximum entropy principle is illustrated. It is built the code UMESTRAT, to apply the described strategy in a semiautomatic way. The application of UMESTRAT is shown with a computational example. The second part of this work deals with the improvement of the X-ray Boltzmann model, by studying two radiative interactions neglected in the current photon models. Firstly it is studied the characteristic line emission due to Compton ionization. It is developed a strategy that allows the evaluation of this contribution for the shells K, L and M of all elements with Z from 11 to 92. It is evaluated the single shell Compton/photoelectric ratio as a function of the primary photon energy. It is derived the energy values at which the Compton interaction becomes the prevailing process to produce ionization for the considered shells. Finally it is introduced a new kernel for the XRF from Compton ionization. In a second place it is characterized the bremsstrahlung radiative contribution due the secondary electrons. The bremsstrahlung radiation is characterized in terms of space, angle and energy, for all elements whit Z=1-92 in the energy range 1–150 keV by using the Monte Carlo code PENELOPE. It is demonstrated that bremsstrahlung radiative contribution can be well approximated with an isotropic point photon source. It is created a data library comprising the energetic distributions of bremsstrahlung. It is developed a new bremsstrahlung kernel which allows the introduction of this contribution in the modified Boltzmann equation. An example of application to the simulation of a synchrotron experiment is shown.

Percieved Organizational Efficacy in Internationalized Companies: Application of Competing Values Approach and Collective Efficacy

This dissertation focuses on “organizational efficacy”, in particular on employees’ beliefs of organizational capacity to be efficacious. Organizational efficacy is considered from two perspectives – competing values approach and collective efficacy, and evaluated in internationalized companies. The dissertation is composed of three studies. The data were collected in thirteen Italian companies on different stages of internationalization for a total number of respondents is 358. In the first study the factorial validity of the competing values instrument (Rohrbaugh, 1981) was investigated and confirmed. Two scales were used to measure collective efficacy: a general collective efficacy scale (Bohn, 2010), and a specific collective efficacy scale, developed following suggestions of Borgogni et al. (2001), it evaluates employees’ beliefs of efficacy of organizations in the international market. The findings suggest that competing values and collective organizational efficacy instruments may provide a multi-faceted measurement of employees’ beliefs of organizational efficacy. The second study examined the relationship between organizational efficacy and collective work engagement. To measure collective work engagement the UWES-9 (Schaufeli & Bakker, 2003) was adapted at the group level; its factor structure and reliability were similar to the standard UWES-9. The findings suggest that organizational efficacy fully predicts collective work engagement. Also we investigated whether leadership moderates the relationship between organizational efficacy and collective work engagement. We operationalized leadership style with MLQ (Bass & Avolio, 1995); the results suggest that intellectual stimulation and idealized influence (transformational leadership) and contingent reward (transactional leadership) enhance the impact of organizational efficacy on collective work engagement. In the third study we investigated organizational efficacy and collective work engagement in internationalized companies. The findings show that beliefs of organizational efficacy vary across companies in different stages of internationalization, while no significant difference was found for collective work engagement. Limitations, practical implications and future studies are discussed in the conclusion.