Dati geochimici ed ecologici di foraminiferi planctonici. Implicazioni paleoceanografiche in due aree chiave: Oceano Meridionale e Mare Mediterraneo.

La studio della distribuzione spaziale e temporale della associazioni a foraminiferi planctonici, campionati in zone con differente regime idrografico, ha permesso di comprendere che molte specie possono essere diagnostiche della presenza di diverse masse d’acqua superficiali e sottosuperficiali e di diversi regimi di nutrienti nelle acque oceaniche. Parte di questo lavoro di tesi si basa sullo studio delle associazioni a foraminiferi planctonici attualmente viventi nel Settore Pacifico dell’Oceano Meridionale (Mare di Ross e Zona del Fronte Polare) e nel Mare Mediterraneo (Mar Tirreno Meridionale). L’obiettivo di questo studio è quello di comprendere i fattori (temperatura, salinità, nutrienti etc.) che determinano la distribuzione attuale delle diverse specie al fine di valutarne il valore di “indicatori” (proxies) utili alla ricostruzione degli scenari paleoclimatici e paleoceanografici succedutisi in queste aree. I risultati documentano che la distribuzione delle diverse specie, il numero di individui e le variazioni nella morfologia di alcuni taxa sono correlate alle caratteristiche chimico-fisiche della colonna e alla disponibilità di nutrienti e di clorofilla. La seconda parte del lavoro di tesi ha previsto l’analisi degli isotopi stabili dell’ossigeno e del rapporto Mg/Ca in gusci di N. pachyderma (sin) prelevati da pescate di micro zooplancton (per tarare l’equazione di paleo temperatura) da un box core e da una carota provenienti dalla zona del Fronte Polare (Oceano Pacifico meridionale), al fine di ricostruire le variazioni di temperatura negli ultimi 13 ka e durante la Mid-Pleistocene Revolution. Le temperature, dedotte tramite i valori degli isotopi stabili dell’ossigeno, sono coerenti con le temperature attuali documentate in questa zona e il trend di temperatura è paragonabile a quelli riportati in letteratura anche per eventi climatici come lo Younger Dryas e il mid-Holocene Optimum. I valori del rapporto Mg/Ca misurato tramite due diverse tecniche di analisi (laser ablation e analisi in soluzione) sono risultati sempre molto più alti dei valori riportati in letteratura per la stessa specie. La laser ablation sembra carente dal punto di vista del cleaning del campione e da questo studio emerge che le due tecniche non sono comparabili e che non possono essere usate indifferentemente sullo stesso campione. Per quanto riguarda l’analisi dei campioni in soluzione è stato migliorato il protocollo di cleaning per il trattamento di campioni antartici, che ha permesso di ottenere valori veritieri e utili ai fini delle ricostruzioni di paleotemperatura. Tuttavia, rimane verosimile l’ipotesi che in ambienti particolari come questo, con salinità e temperature molto basse, l’incorporazione del Mg all’interno del guscio risenta delle condizioni particolari e che non segua quindi la relazione esponenziale con la temperatura ampiamente dimostrata ad altre latitudini.

Sviluppo di metodi innovativi per la sintesi di nanoparticelle di interesse industriale

Among various nanoparticles, noble metal nanoparticles have attracted considerable attention due to their optical, catalytic and conducting properties. This work has been focused on the development of an innovative method of synthesis for the preparation of metal nanosuspensions of Au, Ag, Cu, in order to achieve stable sols, showing suitable features to allow an industrial scale up of the processes. The research was developed in collaboration with a company interested in the large scale production of the studied nanosuspensions. In order to develop a commercial process, high solid concentration, long time colloidal stability and particle size control, are required. Two synthesis routes, differing by the used solvents, have been implemented: polyol based and water based synthesis. In order to achieve a process intensification the microwave heating has been applied. As a result, colloidal nanosuspensions with suitable dimensions, good optical properties, very high solid content and good stability, have been synthesized by simple and environmental friendly methods. Particularly, due to some interesting results an optimized synthesis process has been patented. Both water and polyol based synthesis, developed in the presence of a reducing agent and of a chelating polymer, allowed to obtain particle size-control and colloidal stability by tuning the different parameters. Furthermore, it has been verified that microwave device, due to its rapid and homogeneous heating, provides some advantages over conventional method. In order to optimize the final suspensions properties, for each synthesis it has been studied the effect of different parameters (temperature, time, precursors concentrations, etc) and throughout a specific optimization action a right control on nucleation and growth processes has been achieved. The achieved nanoparticles were confirmed by XRD analysis to be the desired metal phases, even at the lowest synthesis temperatures. The particles showed a diameter, measured by STEM and dynamic light scattering technique (DLS), ranging from 10 to 60 nm. Surface plasmon resonance (SPR) was monitored by UV-VIS spectroscopy confirming its dependence by nanoparticles size and shape. Moreover the reaction yield has been assessed by ICP analysis performed on the unreacted metal cations. Finally, thermal conductivity and antibacterial activity characterizations of copper and silver sols respectively are now ongoing in order to check their application as nanofluid in heat transfer processes and as antibacterial agent.

Development of Clinical Decision Support Systems based on Mathematical Models of Physiological Systems

In the last years of research, I focused my studies on different physiological problems. Together with my supervisors, I developed/improved different mathematical models in order to create valid tools useful for a better understanding of important clinical issues. The aim of all this work is to develop tools for learning and understanding cardiac and cerebrovascular physiology as well as pathology, generating research questions and developing clinical decision support systems useful for intensive care unit patients. I. ICP-model Designed for Medical Education We developed a comprehensive cerebral blood flow and intracranial pressure model to simulate and study the complex interactions in cerebrovascular dynamics caused by multiple simultaneous alterations, including normal and abnormal functional states of auto-regulation of the brain. Individual published equations (derived from prior animal and human studies) were implemented into a comprehensive simulation program. Included in the normal physiological modelling was: intracranial pressure, cerebral blood flow, blood pressure, and carbon dioxide (CO2) partial pressure. We also added external and pathological perturbations, such as head up position and intracranial haemorrhage. The model performed clinically realistically given inputs of published traumatized patients, and cases encountered by clinicians. The pulsatile nature of the output graphics was easy for clinicians to interpret. The manoeuvres simulated include changes of basic physiological inputs (e.g. blood pressure, central venous pressure, CO2 tension, head up position, and respiratory effects on vascular pressures) as well as pathological inputs (e.g. acute intracranial bleeding, and obstruction of cerebrospinal outflow). Based on the results, we believe the model would be useful to teach complex relationships of brain haemodynamics and study clinical research questions such as the optimal head-up position, the effects of intracranial haemorrhage on cerebral haemodynamics, as well as the best CO2 concentration to reach the optimal compromise between intracranial pressure and perfusion. We believe this model would be useful for both beginners and advanced learners. It could be used by practicing clinicians to model individual patients (entering the effects of needed clinical manipulations, and then running the model to test for optimal combinations of therapeutic manoeuvres). II. A Heterogeneous Cerebrovascular Mathematical Model Cerebrovascular pathologies are extremely complex, due to the multitude of factors acting simultaneously on cerebral haemodynamics. In this work, the mathematical model of cerebral haemodynamics and intracranial pressure dynamics, described in the point I, is extended to account for heterogeneity in cerebral blood flow. The model includes the Circle of Willis, six regional districts independently regulated by autoregulation and CO2 reactivity, distal cortical anastomoses, venous circulation, the cerebrospinal fluid circulation, and the intracranial pressure-volume relationship. Results agree with data in the literature and highlight the existence of a monotonic relationship between transient hyperemic response and the autoregulation gain. During unilateral internal carotid artery stenosis, local blood flow regulation is progressively lost in the ipsilateral territory with the presence of a steal phenomenon, while the anterior communicating artery plays the major role to redistribute the available blood flow. Conversely, distal collateral circulation plays a major role during unilateral occlusion of the middle cerebral artery. In conclusion, the model is able to reproduce several different pathological conditions characterized by heterogeneity in cerebrovascular haemodynamics and can not only explain generalized results in terms of physiological mechanisms involved, but also, by individualizing parameters, may represent a valuable tool to help with difficult clinical decisions. III. Effect of Cushing Response on Systemic Arterial Pressure. During cerebral hypoxic conditions, the sympathetic system causes an increase in arterial pressure (Cushing response), creating a link between the cerebral and the systemic circulation. This work investigates the complex relationships among cerebrovascular dynamics, intracranial pressure, Cushing response, and short-term systemic regulation, during plateau waves, by means of an original mathematical model. The model incorporates the pulsating heart, the pulmonary circulation and the systemic circulation, with an accurate description of the cerebral circulation and the intracranial pressure dynamics (same model as in the first paragraph). Various regulatory mechanisms are included: cerebral autoregulation, local blood flow control by oxygen (O2) and/or CO2 changes, sympathetic and vagal regulation of cardiovascular parameters by several reflex mechanisms (chemoreceptors, lung-stretch receptors, baroreceptors). The Cushing response has been described assuming a dramatic increase in sympathetic activity to vessels during a fall in brain O2 delivery. With this assumption, the model is able to simulate the cardiovascular effects experimentally observed when intracranial pressure is artificially elevated and maintained at constant level (arterial pressure increase and bradicardia). According to the model, these effects arise from the interaction between the Cushing response and the baroreflex response (secondary to arterial pressure increase). Then, patients with severe head injury have been simulated by reducing intracranial compliance and cerebrospinal fluid reabsorption. With these changes, oscillations with plateau waves developed. In these conditions, model results indicate that the Cushing response may have both positive effects, reducing the duration of the plateau phase via an increase in cerebral perfusion pressure, and negative effects, increasing the intracranial pressure plateau level, with a risk of greater compression of the cerebral vessels. This model may be of value to assist clinicians in finding the balance between clinical benefits of the Cushing response and its shortcomings. IV. Comprehensive Cardiopulmonary Simulation Model for the Analysis of Hypercapnic Respiratory Failure We developed a new comprehensive cardiopulmonary model that takes into account the mutual interactions between the cardiovascular and the respiratory systems along with their short-term regulatory mechanisms. The model includes the heart, systemic and pulmonary circulations, lung mechanics, gas exchange and transport equations, and cardio-ventilatory control. Results show good agreement with published patient data in case of normoxic and hyperoxic hypercapnia simulations. In particular, simulations predict a moderate increase in mean systemic arterial pressure and heart rate, with almost no change in cardiac output, paralleled by a relevant increase in minute ventilation, tidal volume and respiratory rate. The model can represent a valid tool for clinical practice and medical research, providing an alternative way to experience-based clinical decisions. In conclusion, models are not only capable of summarizing current knowledge, but also identifying missing knowledge. In the former case they can serve as training aids for teaching the operation of complex systems, especially if the model can be used to demonstrate the outcome of experiments. In the latter case they generate experiments to be performed to gather the missing data.

Cluster-derived Gold/Iron catalysts for environmental applications

During the last years we assisted to an exponential growth of scientific discoveries for catalysis by gold and many applications have been found for Au-based catalysts. In the literature there are several studies concerning the use of gold-based catalysts for environmental applications and good results are reported for the catalytic combustion of different volatile organic compounds (VOCs). Recently it has also been established that gold-based catalysts are potentially capable of being effectively employed in fuel cells in order to remove CO traces by preferential CO oxidation in H2-rich streams. Bi-metallic catalysts have attracted increasing attention because of their markedly different properties from either of the costituent metals, and above all their enhanced catalytic activity, selectivity and stability. In the literature there are several studies demostrating the beneficial effect due to the addition of an iron component to gold supported catalysts in terms of enhanced activity, selectivity, resistence to deactivation and prolonged lifetime of the catalyst. In this work we tried to develop a methodology for the preparation of iron stabilized gold nanoparticles with controlled size and composition, particularly in terms of obtaining an intimate contact between different phases, since it is well known that the catalytic behaviour of multi-component supported catalysts is strongly influenced by the size of the metal particles and by their reciprocal interaction. Ligand stabilized metal clusters, with nanometric dimensions, are possible precursors for the preparation of catalytically active nanoparticles with controlled dimensions and compositions. Among these, metal carbonyl clusters are quite attractive, since they can be prepared with several different sizes and compositions and, moreover, they are decomposed under very mild conditions. A novel preparation method was developed during this thesis for the preparation of iron and gold/iron supported catalysts using bi-metallic carbonyl clusters as precursors of highly dispersed nanoparticles over TiO2 and CeO2, which are widely considered two of the most suitable supports for gold nanoparticles. Au/FeOx catalysts were prepared by employing the bi-metallic carbonyl cluster salts [NEt4]4[Au4Fe4(CO)16] (Fe/Au=1) and [NEt4][AuFe4(CO)16] (Fe/Au=4), and for comparison FeOx samples were prepared by employing the homometallic [NEt4][HFe3(CO)11] cluster. These clusters were prepared by Prof. Longoni research group (Department of Physical and Inorganic Chemistry- University of Bologna). Particular attention was dedicated to the optimization of a suitable thermal treatment in order to achieve, apart from a good Au and Fe metal dispersion, also the formation of appropriate species with good catalytic properties. A deep IR study was carried out in order to understand the physical interaction between clusters and different supports and detect the occurrence of chemical reactions between them at any stage of the preparation. The characterization by BET, XRD, TEM, H2-TPR, ICP-AES and XPS was performed in order to investigate the catalysts properties, whit particular attention to the interaction between Au and Fe and its influence on the catalytic activity. This novel preparation method resulted in small gold metallic nanoparticles surrounded by highly dispersed iron oxide species, essentially in an amorphous phase, on both TiO2 and CeO2. The results presented in this thesis confirmed that FeOx species can stabilize small Au particles, since keeping costant the gold content but introducing a higher iron amount a higher metal dispersion was achieved. Partial encapsulation of gold atoms by iron species was observed since the Au/Fe surface ratio was found much lower than bulk ratio and a strong interaction between gold and oxide species, both of iron oxide and supports, was achieved. The prepared catalysts were tested in the total oxidation of VOCs, using toluene and methanol as probe molecules for aromatics and alchols, respectively, and in the PROX reaction. Different performances were observed on titania and ceria catalysts, on both toluene and methanol combustion. Toluene combustion on titania catalyst was found to be enhanced increasing iron loading while a moderate effect on FeOx-Ti activity was achieved by Au addition. In this case toluene combustion was improved due to a higher oxygen mobility depending on enhanced oxygen activation by FeOx and Au/FeOx dispersed on titania. On the contrary ceria activity was strongly decreased in the presence of FeOx, while the introduction of gold was found to moderate the detrimental effect of iron species. In fact, excellent ceria performances are due to its ability to adsorb toluene and O2. Since toluene activation is the determining factor for its oxidation, the partial coverage of ceria sites, responsible of toluene adsorption, by FeOx species finely dispersed on the surface resulted in worse efficiency in toluene combustion. Better results were obtained for both ceria and titania catalysts on methanol total oxidation. In this case, the performances achieved on differently supported catalysts indicate that the oxygen mobility is the determining factor in this reaction. The introduction of gold on both TiO2 and CeO2 catalysts, lead to a higher oxygen mobility due to the weakening of both Fe-O and Ce-O bonds and consequently to enhanced methanol combustion. The catalytic activity was found to strongly depend on oxygen mobility and followed the same trend observed for catalysts reducibility. Regarding CO PROX reaction, it was observed that Au/FeOx titania catalysts are less active than ceria ones, due to the lower reducibility of titania compared to ceria. In fact the availability of lattice oxygen involved in PROX reaction is much higher in the latter catalysts. However, the CO PROX performances observed for ceria catalysts are not really high compared to data reported in literature, probably due to the very low Au/Fe surface ratio achieved with this preparation method. CO preferential oxidation was found to strongly depend on Au particle size but also on surface oxygen reducibility, depending on the different oxide species which can be formed using different thermal treatment conditions or varying the iron loading over the support.

Il monitoraggio suolo-pianta per la valutazione dell'inquinamento da metalli pesanti nell'ambiente urbano

Il lavoro di tesi è incentrato sulla valutazione del degrado del suolo dovuto a fenomeni di inquinamento da metalli pesanti aerodispersi, ovvero apportati al suolo mediante deposizioni atmosferiche secche ed umide, in ambiente urbano. Lo scopo della ricerca è legato principalmente alla valutazione dell’efficienza del metodo di monitoraggio ideato che affianca al campionamento e all’analisi pedologica l’utilizzo di bioindicatori indigeni, quali il muschio, il cotico erboso, le foglie di piante arboree e il materiale pulverulento depositatosi su di esse. Una semplice analisi pedologica infatti non permette di discriminare la natura dei contaminanti in esso ritrovati. I metalli pesanti possono raggiungere il suolo attraverso diverse vie. In primo luogo questi elementi in traccia si trovano naturalmente nei suoi; ma numerose sono le fonti antropiche: attività industriali, traffico veicolare, incenerimento dei rifiuti, impianti di riscaldamento domestico, pratiche agricole, utilizzo di acque con bassi requisiti di qualità, ecc. Questo fa capire come una semplice analisi del contenuto totale o pseudo - totale di metalli pesanti nel suolo non riesca a rispondere alla domanda su quale si la fonte di provenienza di queste sostanze. Il metodo di monitoraggio integrato suolo- pianta è stato applicato a due diversi casi di studio. Il primo denominato “Progetto per il monitoraggio e valutazione delle concentrazioni in metalli pesanti e micro elementi sul sistema suolo - pianta in aree urbane adibite a verde pubblico dell’Emilia – Romagna” ha permesso di valutare l’insorgenza di una diminuzione della qualità dell’ecosistema parco urbano causata dalla ricaduta di metalli pesanti aerotrasportati, in tre differenti realtà urbane dell’Emilia Romagna: le città di Bologna, Ferrara e Cesena. Le città presentano caratteristiche pedologiche, ambientali ed economico-sociali molto diverse tra loro. Questo ha permesso di studiare l’efficienza del metodo su campioni di suolo e di vegetali molto diversi per quanto riguarda le aliquote di metalli pesanti riscontrate. Il secondo caso di studio il “Monitoraggio relativo al contenuto in metalli pesanti e microelementi nel sistema acqua-suolo-pianta delle aree circostanti l’impianto di termovalorizzazione e di incenerimento del Frullo (Granarolo dell’Emilia - BO)” è stato invece incentrato sulla valutazione della qualità ambientale delle aree circostanti l’inceneritore. Qui lo scenario si presentava più omogeneo dal punto di vista pedologico rispetto al caso di studio precedente, ma molto più complesso l’ecosistema di riferimento (urbano, extra-urbano ed agricolo). Seppure il metodo suolo-pianta abbia permesso di valutare gli apporti di metalli pesanti introdotti per via atmosferica, non è stato possibile imputarne l’origine alle sole emissioni prodotte dall’inceneritore.

Integrated analysis and design of optimization and up-scaling of inductively coupled plasma synthesis of nanoparticles

This study is focused on radio-frequency inductively coupled thermal plasma (ICP) synthesis of nanoparticles, combining experimental and modelling approaches towards process optimization and industrial scale-up, in the framework of the FP7-NMP SIMBA European project (Scaling-up of ICP technology for continuous production of Metallic nanopowders for Battery Applications). First the state of the art of nanoparticle production through conventional and plasma routes is summarized, then results for the characterization of the plasma source and on the investigation of the nanoparticle synthesis phenomenon, aiming at highlighting fundamental process parameters while adopting a design oriented modelling approach, are presented. In particular, an energy balance of the torch and of the reaction chamber, employing a calorimetric method, is presented, while results for three- and two-dimensional modelling of an ICP system are compared with calorimetric and enthalpy probe measurements to validate the temperature field predicted by the model and used to characterize the ICP system under powder-free conditions. Moreover, results from the modeling of critical phases of ICP synthesis process, such as precursor evaporation, vapour conversion in nanoparticles and nanoparticle growth, are presented, with the aim of providing useful insights both for the design and optimization of the process and on the underlying physical phenomena. Indeed, precursor evaporation, one of the phases holding the highest impact on industrial feasibility of the process, is discussed; by employing models to describe particle trajectories and thermal histories, adapted from the ones originally developed for other plasma technologies or applications, such as DC non-transferred arc torches and powder spherodization, the evaporation of micro-sized Si solid precursor in a laboratory scale ICP system is investigated. Finally, a discussion on the role of thermo-fluid dynamic fields on nano-particle formation is presented, as well as a study on the effect of the reaction chamber geometry on produced nanoparticle characteristics and process yield.

Flow Field–Flow Fractionation for size analysis and characterization of nanoparticles for applications in Life Sciences

Nanotechnologies are rapidly expanding because of the opportunities that the new materials offer in many areas such as the manufacturing industry, food production, processing and preservation, and in the pharmaceutical and cosmetic industry. Size distribution of the nanoparticles determines their properties and is a fundamental parameter that needs to be monitored from the small-scale synthesis up to the bulk production and quality control of nanotech products on the market. A consequence of the increasing number of applications of nanomaterial is that the EU regulatory authorities are introducing the obligation for companies that make use of nanomaterials to acquire analytical platforms for the assessment of the size parameters of the nanomaterials. In this work, Asymmetrical Flow Field-Flow Fractionation (AF4) and Hollow Fiber F4 (HF5), hyphenated with Multiangle Light Scattering (MALS) are presented as tools for a deep functional characterization of nanoparticles. In particular, it is demonstrated the applicability of AF4-MALS for the characterization of liposomes in a wide series of mediums. Afterwards the technique is used to explore the functional features of a liposomal drug vector in terms of its biological and physical interaction with blood serum components: a comprehensive approach to understand the behavior of lipid vesicles in terms of drug release and fusion/interaction with other biological species is described, together with weaknesses and strength of the method. Afterwards the size characterization, size stability, and conjugation of azidothymidine drug molecules with a new generation of metastable drug vectors, the Metal Organic Frameworks, is discussed. Lastly, it is shown the applicability of HF5-ICP-MS for the rapid screening of samples of relevant nanorisk: rather than a deep and comprehensive characterization it this time shown a quick and smart methodology that within few steps provides qualitative information on the content of metallic nanoparticles in tattoo ink samples.

Identificazione di possibili unita' di stock di Anguilla anguilla mediante analisi microchimica e morfometrica degli otoliti

L’anguilla europea, è una specie eurialina catadroma con un complesso ciclo biologico: l’area di riproduzione, unica, si trova molto distante da quella di distribuzione. La specie necessita di una gestione dello stock a fini conservazionistici. Il problema è europeo: lo stock è unico, distribuito in Europa e nell’Africa settentrionale, si riproduce in Atlantico ed è panmittico. C’è preoccupazione per il declino del reclutamento e delle catture di adulti. Lo scopo del progetto è di individuare possibili unità di stock nella penisola italiana. La ricerca è basata sullo studio degli otoliti mediante analisi morfometrica e microchimica. I contorni degli otoliti sono sottoposti ad analisi ellittica di Fourier per individuare eventuali gruppi. Gli otoliti sono stati levigati per effettuare: letture d’età, indagini microstrutturali al SEM delle fasi larvali, analisi microchimiche LA-ICP-MS del nucleo, studiarne l’origine e valutare l’ambiente di sviluppo. Le indagini morfometriche mostrano evidenti pattern ontogenetici, ma non legati ocorrelati alla località, sesso o anno di nascita. Le indagini microstrutturali hanno evidenziano l’alto contenuto organico nucleare, un pattern comune di crescita ed eventi chiave delle fasi larvali, con una media di 212 anelli giornalieri. La microchimica rivela che le larve si sviluppano in acque salate fino alla metamorfosi, poi migrano verso acque meno salate. Le analisi su campioni nati nello stesso anno, evidenziano due gruppi: individui di rimonta naturale e individui di ripopolamento. I profili nucleo bordo evidenziano la permanenza a salinità intermedie degli adulti. L’attività di ricerca si è dimostrata proficua dal punto di vista tecnico con la messa a punto di protocolli innovativi e con forti ricadute sulla riduzione dei tempi e costi d’analisi. Il debole segnale di possibili unità di stock andrà verificato in futuro mediante analisi più dettagliate discriminando meglio la storia di ogni singolo individuo.

Modelling, diagnostics and experimental analysis of plasma assisted processes for material treatment

This work presents results from experimental investigations of several different atmospheric pressure plasmas applications, such as Metal Inert Gas (MIG) welding and Plasma Arc Cutting (PAC) and Welding (PAW) sources, as well as Inductively Coupled Plasma (ICP) torches. The main diagnostic tool that has been used is High Speed Imaging (HSI), often assisted by Schlieren imaging to analyse non-visible phenomena. Furthermore, starting from thermo-fluid-dynamic models developed by the University of Bologna group, such plasma processes have been studied also with new advanced models, focusing for instance on the interaction between a melting metal wire and a plasma, or considering non-equilibrium phenomena for diagnostics of plasma arcs. Additionally, the experimental diagnostic tools that have been developed for industrial thermal plasmas have been used also for the characterization of innovative low temperature atmospheric pressure non equilibrium plasmas, such as dielectric barrier discharges (DBD) and Plasma Jets. These sources are controlled by few kV voltage pulses with pulse rise time of few nanoseconds to avoid the formation of a plasma arc, with interesting applications in surface functionalization of thermosensitive materials. In order to investigate also bio-medical applications of thermal plasma, a self-developed quenching device has been connected to an ICP torch. Such device has allowed inactivation of several kinds of bacteria spread on petri dishes, by keeping the substrate temperature lower than 40 degrees, which is a strict requirement in order to allow the treatment of living tissues.