Produzione automatizzata per nastratura di componenti strutturali in materiale composito

Questa dissertazione tratterà l’argomento dello studio di metodi di progettazione e processi tecnologici innovativi per l’industrializzazione in medio-grande serie di componenti strutturali in materiale composito. L’interesse della ricerca verso questo ambito è suscitato dai notevoli vantaggi che l’utilizzo di materiali dall’alto rapporto prestazioni meccaniche/peso danno nella ricerca di elevate prestazioni in applicazioni sportive e diminuzione dei consumi ed emissioni inquinanti in mezzi di trasporto di grande serie. Lo studio di componenti in materiale composito è caratterizzato dalla peculiarità di non poter disgiungere la progettazione della geometria della parte da quella del materiale e del processo, ed in questo senso nella figura del progettista si vanno a riassumere sinergicamente competenze riguardanti i tre ambiti. Lo scopo di questo lavoro è la proposizione di una metodologia di progettazione e produzione di componenti strutturali che permetta l’utilizzazione ottimale della natura fibrosa del materiale composito sia dal punto di vista del trasferimento dei carichi tra diversi componenti, sia dal punto di vista del processo di laminazione che avviene per nastratura automatizzata. Lo studio è volto a mostrare in quali termini tale tecnologia sia potenzialmente in grado di superare i vincoli di forma ed i limiti di efficienza meccanica delle giunzioni tra le parti e di garantire maggiore produttività e costi inferiori rispetti ai diversi metodi di produzione che rappresentano oggi lo stato dell’arte dell’industrializzazione in medio-grande serie. Particolare attenzione verrà posta sull’utilizzo della tecnologia oggetto di studio per la produzione di telai automobilistici.

Trattamenti ad aria calda per la decontaminazione superficiale delle uova in guscio

In order to improve the animal welfare, the Council Directive 1999/74/EC (defining minimum standards for the welfare of laying hens) will ban conventional cage systems since 2012, in favour of enriched cages or floor systems. As a consequence an increased risk of bacterial contamination of eggshell is expected (EFSA, 2005). Furthermore egg-associated salmonellosis is an important public health problem throughout the world (Roberts et al., 1994). In this regard the introduction of efficient measures to reduce eggshell contamination by S. Enteritidis or other bacterial pathogens, and thus to prevent any potential or additional food safety risk for Human health, may be envisaged. The hot air pasteurization can be a viable alternative for the decontamination of the surface of the egg shell. Few studies have been performed on the decontamination power of this technique on table eggs (Hou et al, 1996; James et al., 2002). The aim of this study was to develop innovative techniques to remove surface contamination of shell eggs by hot air under natural or forced convection. Initially two simplified finite element models describing the thermal interaction between the air and egg were developed, respectively for the natural and forced convection. The numerical models were validated using an egg simulant equipped by type-K thermocouple (Chromel/Alumel). Once validated, the models allowed the selection of a thermal cycle with an inner temperature always lower than 55°C. Subsequently a specific apparatus composed by two hot air generators, one cold air generator and rolling cylinder support, was built to physically condition the eggs. The decontamination power of the thermal treatments was evaluated on shell eggs experimentally inoculated with either Salmonella Enteritidis, Escherichia coli, Listeria monocytogenes and on shell eggs containing only the indigenous microflora. The applicability of treatments was further evaluated by comparing quality traits of treated and not treated eggs immediately after the treatment and after 28 days of storage at 20°C. The results showed that the treatment characterized by two shots of hot air at 350°C for 8 sec, spaced by a cooling interval of 32 (forced convection), reduce the bacterial population of more than 90% (Salmonella enteritidis and Listeria monocytogenes). No statistically significant results were obtained comparing E. coli treated and not treated eggs as well as indigenous microflora treated and not treated eggs. A reduction of 2.6 log was observed on Salmonella enteritidis load of eggs immediately after the treatment in oven at 200°C for 200 minutes (natural convection). Furthermore no detrimental effects on quality traits of treated eggs were recorded. These results support the hot air techniques for the surface decontamination of table eggs as an effective industrial process.

Biomass Gasification - Process analysis and dimensioning aspects for downdraft units and gas cleaning lines

In such territories where food production is mostly scattered in several small / medium size or even domestic farms, a lot of heterogeneous residues are produced yearly, since farmers usually carry out different activities in their properties. The amount and composition of farm residues, therefore, widely change during year, according to the single production process periodically achieved. Coupling high efficiency micro-cogeneration energy units with easy handling biomass conversion equipments, suitable to treat different materials, would provide many important advantages to the farmers and to the community as well, so that the increase in feedstock flexibility of gasification units is nowadays seen as a further paramount step towards their wide spreading in rural areas and as a real necessity for their utilization at small scale. Two main research topics were thought to be of main concern at this purpose, and they were therefore discussed in this work: the investigation of fuels properties impact on gasification process development and the technical feasibility of small scale gasification units integration with cogeneration systems. According to these two main aspects, the present work was thus divided in two main parts. The first one is focused on the biomass gasification process, that was investigated in its theoretical aspects and then analytically modelled in order to simulate thermo-chemical conversion of different biomass fuels, such as wood (park waste wood and softwood), wheat straw, sewage sludge and refuse derived fuels. The main idea is to correlate the results of reactor design procedures with the physical properties of biomasses and the corresponding working conditions of gasifiers (temperature profile, above all), in order to point out the main differences which prevent the use of the same conversion unit for different materials. At this scope, a gasification kinetic free model was initially developed in Excel sheets, considering different values of air to biomass ratio and the downdraft gasification technology as particular examined application. The differences in syngas production and working conditions (process temperatures, above all) among the considered fuels were tried to be connected to some biomass properties, such elementary composition, ash and water contents. The novelty of this analytical approach was the use of kinetic constants ratio in order to determine oxygen distribution among the different oxidation reactions (regarding volatile matter only) while equilibrium of water gas shift reaction was considered in gasification zone, by which the energy and mass balances involved in the process algorithm were linked together, as well. Moreover, the main advantage of this analytical tool is the easiness by which the input data corresponding to the particular biomass materials can be inserted into the model, so that a rapid evaluation on their own thermo-chemical conversion properties is possible to be obtained, mainly based on their chemical composition A good conformity of the model results with the other literature and experimental data was detected for almost all the considered materials (except for refuse derived fuels, because of their unfitting chemical composition with the model assumptions). Successively, a dimensioning procedure for open core downdraft gasifiers was set up, by the analysis on the fundamental thermo-physical and thermo-chemical mechanisms which are supposed to regulate the main solid conversion steps involved in the gasification process. Gasification units were schematically subdivided in four reaction zones, respectively corresponding to biomass heating, solids drying, pyrolysis and char gasification processes, and the time required for the full development of each of these steps was correlated to the kinetics rates (for pyrolysis and char gasification processes only) and to the heat and mass transfer phenomena from gas to solid phase. On the basis of this analysis and according to the kinetic free model results and biomass physical properties (particles size, above all) it was achieved that for all the considered materials char gasification step is kinetically limited and therefore temperature is the main working parameter controlling this step. Solids drying is mainly regulated by heat transfer from bulk gas to the inner layers of particles and the corresponding time especially depends on particle size. Biomass heating is almost totally achieved by the radiative heat transfer from the hot walls of reactor to the bed of material. For pyrolysis, instead, working temperature, particles size and the same nature of biomass (through its own pyrolysis heat) have all comparable weights on the process development, so that the corresponding time can be differently depending on one of these factors according to the particular fuel is gasified and the particular conditions are established inside the gasifier. The same analysis also led to the estimation of reaction zone volumes for each biomass fuel, so as a comparison among the dimensions of the differently fed gasification units was finally accomplished. Each biomass material showed a different volumes distribution, so that any dimensioned gasification unit does not seem to be suitable for more than one biomass species. Nevertheless, since reactors diameters were found out quite similar for all the examined materials, it could be envisaged to design a single units for all of them by adopting the largest diameter and by combining together the maximum heights of each reaction zone, as they were calculated for the different biomasses. A total height of gasifier as around 2400mm would be obtained in this case. Besides, by arranging air injecting nozzles at different levels along the reactor, gasification zone could be properly set up according to the particular material is in turn gasified. Finally, since gasification and pyrolysis times were found to considerably change according to even short temperature variations, it could be also envisaged to regulate air feeding rate for each gasified material (which process temperatures depend on), so as the available reactor volumes would be suitable for the complete development of solid conversion in each case, without even changing fluid dynamics behaviour of the unit as well as air/biomass ratio in noticeable measure. The second part of this work dealt with the gas cleaning systems to be adopted downstream the gasifiers in order to run high efficiency CHP units (i.e. internal engines and micro-turbines). Especially in the case multi–fuel gasifiers are assumed to be used, weightier gas cleaning lines need to be envisaged in order to reach the standard gas quality degree required to fuel cogeneration units. Indeed, as the more heterogeneous feed to the gasification unit, several contaminant species can simultaneously be present in the exit gas stream and, as a consequence, suitable gas cleaning systems have to be designed. In this work, an overall study on gas cleaning lines assessment is carried out. Differently from the other research efforts carried out in the same field, the main scope is to define general arrangements for gas cleaning lines suitable to remove several contaminants from the gas stream, independently on the feedstock material and the energy plant size The gas contaminant species taken into account in this analysis were: particulate, tars, sulphur (in H2S form), alkali metals, nitrogen (in NH3 form) and acid gases (in HCl form). For each of these species, alternative cleaning devices were designed according to three different plant sizes, respectively corresponding with 8Nm3/h, 125Nm3/h and 350Nm3/h gas flows. Their performances were examined on the basis of their optimal working conditions (efficiency, temperature and pressure drops, above all) and their own consumption of energy and materials. Successively, the designed units were combined together in different overall gas cleaning line arrangements, paths, by following some technical constraints which were mainly determined from the same performance analysis on the cleaning units and from the presumable synergic effects by contaminants on the right working of some of them (filters clogging, catalysts deactivation, etc.). One of the main issues to be stated in paths design accomplishment was the tars removal from the gas stream, preventing filters plugging and/or line pipes clogging At this scope, a catalytic tars cracking unit was envisaged as the only solution to be adopted, and, therefore, a catalytic material which is able to work at relatively low temperatures was chosen. Nevertheless, a rapid drop in tars cracking efficiency was also estimated for this same material, so that an high frequency of catalysts regeneration and a consequent relevant air consumption for this operation were calculated in all of the cases. Other difficulties had to be overcome in the abatement of alkali metals, which condense at temperatures lower than tars, but they also need to be removed in the first sections of gas cleaning line in order to avoid corrosion of materials. In this case a dry scrubber technology was envisaged, by using the same fine particles filter units and by choosing for them corrosion resistant materials, like ceramic ones. Besides these two solutions which seem to be unavoidable in gas cleaning line design, high temperature gas cleaning lines were not possible to be achieved for the two larger plant sizes, as well. Indeed, as the use of temperature control devices was precluded in the adopted design procedure, ammonia partial oxidation units (as the only considered methods for the abatement of ammonia at high temperature) were not suitable for the large scale units, because of the high increase of reactors temperature by the exothermic reactions involved in the process. In spite of these limitations, yet, overall arrangements for each considered plant size were finally designed, so that the possibility to clean the gas up to the required standard degree was technically demonstrated, even in the case several contaminants are simultaneously present in the gas stream. Moreover, all the possible paths defined for the different plant sizes were compared each others on the basis of some defined operational parameters, among which total pressure drops, total energy losses, number of units and secondary materials consumption. On the basis of this analysis, dry gas cleaning methods proved preferable to the ones including water scrubber technology in al of the cases, especially because of the high water consumption provided by water scrubber units in ammonia adsorption process. This result is yet connected to the possibility to use activated carbon units for ammonia removal and Nahcolite adsorber for chloride acid. The very high efficiency of this latter material is also remarkable. Finally, as an estimation of the overall energy loss pertaining the gas cleaning process, the total enthalpy losses estimated for the three plant sizes were compared with the respective gas streams energy contents, these latter obtained on the basis of low heating value of gas only. This overall study on gas cleaning systems is thus proposed as an analytical tool by which different gas cleaning line configurations can be evaluated, according to the particular practical application they are adopted for and the size of cogeneration unit they are connected to.

Le reologia dei leganti bituminosi stradali: studio delle proprietà meccaniche a seguito di processi di “aging” in laboratorio

Lo studio effettuato pone le sue basi sulla ricerca di materiali stradali che combinino ad elevati standard prestazionali, la riduzione dell’impatto ambientale in fase realizzativa e manutentiva. In particolare il seguente lavoro si occupa dello studio di 7 leganti modificati con polimeri ed additivati con cere. I primi infatti conferiscono alla miscela maggiore elastoplasticità, incrementandone la durabilità e la resistenza a fatica. Nei secondi la presenza del materiale paraffinico contribuisce a ridurre la viscosità del bitume, consentendo un notevole abbassamento della temperatura di produzione e stesa della miscela. Numerosi studi hanno dimostrato che le caratteristiche meccaniche della pavimentazione sono fortemente influenzate dal grado di ossidazione delle componenti organiche del bitume, ovvero dal fenomeno dell’invecchiamento o aging. Pertanto allo studio reologico del bitume, si sono affiancate prove di simulazione dell’ invecchiamento nel breve e lungo termine. In fase di ricerca sperimentale si sono analizzati i leganti modificati ed additivati secondo la teoria della viscoelasticità, simulando le reali condizioni di carico ed invecchiamento alle quali il bitume è sottoposto. Tutte le prove di caratterizzazione reologica avanzata sono state effettuate mediante l’utilizzo del DSR (Dynamic Shear Rheometer - UNI EN 14770 ) in varie configurazioni di prova e l’invecchiamento a breve termine è stato simulato mediante RTFOT (Rolling thin film oven test -UNI EN 12607-1). Si è proposto inoltre una nuova procedura di aging invecchiando il bitume alla temperatura di Twork, ovvero a quel valore della temperatura tale per cui, in fase di messa in opera, si avrà una distribuzione molecolare omogenea del modificante all’interno del bitume.

Networking: the "making of" social networks. A closer look at the process and antecedents of some resourcing-oriented behaviors in organizations.

Social networks are one of the “hot” themes in people’s life and contemporary social research. Considering our “embeddedness” in a thick web of social relations is a study perspective that could unveil a number of explanations of how people may manage their personal and social resources. Looking at people’s behaviors of building and managing their social networks, seems to be an effective way to find some possible rationalization about how to help people getting the best from their resources . The main aim of this dissertation is to give a closer look at the role of networking behaviors. Antecedents, motivations, different steps and measures about networking behaviors and outcomes are analyzed and discussed. Results seem to confirm, in a different setting and time perspective, that networking behaviors include different types and goals that change over time. Effects of networking behaviors seem to find empirical confirmation through social network analysis methods. Both personality and situational self-efficacy seem to predict networking behaviors. Different types of motivational drivers seem to be related to diverse networking behaviors.