Metrologia dei campi di radiazioni di bassa energia

The conversion coefficients from air kerma to ICRU operational dose equivalent quantities for ENEA’s realization of the X-radiation qualities L10-L35 of the ISO “Low Air Kerma rate” series (L), N10-N40 of the ISO “Narrow spectrum” series (N) and H10-H60 of the ISO “High Air-kerma rate” (H) series and two beams at 5 kV and 7.5 kV were determined by utilising X-ray spectrum measurements. The pulse-height spectra were measured using a planar high-purity germanium spectrometer (HPGe) and unfolded to fluence spectra using a stripping procedure then validate with using Monte Carlo generated data of the spectrometer response. HPGe portable detector has a diameter of 8.5 mm and a thickness of 5 mm. The entrance window of the crystal is collimated by a 0.5 mm thick Aluminum ring to an open diameter of 6.5 mm. The crystal is mounted at a distance of 5 mm from the Berillium window (thickness 25.4 micron). The Monte Carlo method (MCNP-4C) was used to calculate the efficiency, escape and Compton curves of a planar high-purity germanium detector (HPGe) in the 5-60 keV energy. These curves were used for the determination of photon spectra produced by the X-ray machine SEIFERT ISOVOLT 160 kV in order to allow a precise characterization of photon beams in the low energy range, according to the ISO 4037. The detector was modelled with the MCNP computer code and validated with experimental data. To verify the measuring and the stripping procedure, the first and the second half-value layers and the air kerma rate were calculated from the counts spectra and compared with the values measured using an a free-air ionization chamber. For each radiation quality, the spectrum was characterized by the parameters given in ISO 4037-1. The conversion coefficients from the air kerma to the ICRU operational quantities Hp(10), Hp(0.07), H’(0.07) and H*(10) were calculated using monoenergetic conversion coefficients. The results are discussed with respect to ISO 4037-4, and compared with published results for low-energy X-ray spectra. The main motivation for this work was the lack of a treatment of the low photon energy region (from a few keV up to about 60 keV).

Sistema per l'estrazione e purificazione di sostanze antiossidanti naturali nelle acque di vegetazione delle olive

The olive oil extraction industry is responsible for the production of high quantities of vegetation waters, represented by the constitutive water of the olive fruit and by the water used during the process. This by-product represent an environmental problem in the olive’s cultivation areas because of its high content of organic matter, with high value of BOD5 and COD. For that reason the disposal of the vegetation water is very difficult and needs a previous depollution. The organic matter of vegetation water mainly consists of polysaccharides, sugars, proteins, organic acids, oil and polyphenols. This last compounds are the principal responsible for the pollution problems, due to their antimicrobial activity, but, at the same time they are well known for their antioxidant properties. The most concentrate phenolic compounds in waters and also in virgin olive oils are secoiridoids like oleuropein, demethyloleuropein and ligstroside derivatives (the dialdehydic form of elenolic acid linked to 3,4-DHPEA, or p-HPEA (3,4-DHPEA-EDA or p-HPEA-EDA) and an isomer of the oleuropein aglycon (3,4-DHPEA-EA). The management of the olive oil vegetation water has been extensively investigated and several different valorisation methods have been proposed, such as the direct use as fertilizer or the transformation by physico-chemical or biological treatments. During the last years researchers focused their interest on the recovery of the phenolic fraction from this waste looking for its exploitation as a natural antioxidant source. At the present only few contributes have been aimed to the utilization for a large scale phenols recovery and further investigations are required for the evaluation of feasibility and costs of the proposed processes. The present PhD thesis reports a preliminary description of a new industrial scale process for the recovery of the phenolic fraction from olive oil vegetation water treated with enzymes, by direct membrane filtration (microfiltration/ultrafiltration with a cut-off of 250 KDa, ultrafiltration with a cut-off of 7 KDa/10 KDa and nanofiltration/reverse osmosis), partial purification by the use of a purification system based on SPE analysis and by a liquid-liquid extraction system (LLE) with contemporary reduction of the pollution related problems. The phenolic fractions of all the samples obtained were qualitatively and quantitatively by HPLC analysis. The work efficiency in terms of flows and in terms of phenolic recovery gave good results. The final phenolic recovery is about 60% respect the initial content in the vegetation waters. The final concentrate has shown a high content of phenols that allow to hypothesize a possible use as zootechnic nutritional supplements. The purification of the final concentrate have garanteed an high purity level of the phenolic extract especially in SPE analysis by the use of XAD-16 (73% of the total phenolic content of the concentrate). This purity level could permit a future food industry employment such as food additive, or, thanks to the strong antioxidant activity, it would be also use in pharmaceutical or cosmetic industry. The vegetation water depollutant activity has brought good results, as a matter of fact the final reverse osmosis permeate has a low pollutant rate in terms of COD and BOD5 values (2% of the initial vegetation water), that could determinate a recycling use in the virgin olive oil mechanical extraction system producing a water saving and reducing thus the oil industry disposal costs .

Thiophene- Based Materials for Photovoltaic Applications

Thiophene oligomers (OTs) and polymers (PTs) are currently attracting remarkable attention as organic materials showing semiconducting, fluorescent, nonlinear optical and liquid crystalline properties. All these properties can be fine-tuned through minor structural modifications. As a consequence, thiophene oligomers and polymers are among the most investigated compounds for applications in organic electronics, optoelectronics and thin film devices such as field effect transistors (FETs), light emitting diodes (LEDs) and photovoltaic devices (PVDs). Our research aims to explore the self-assembly features and the optical, electrical and photovoltaic properties of a class of thiophene based materials so far scarcely investigated, namely that of oligo- and polythiophenes head-to-head substituted with alkyl or S-alkyl chains. In particular, we synthesized these compounds in short reaction times, high yields, high purity and environmentally friendly procedures taking advantage of ultrasound (US) and microwave (MW) enabling technologies in Suzuki-Miyaura cross-couplings.