Fluid dynamic analysis and modelling of industrial chemical equipment

The research is aimed at contributing to the identification of reliable fully predictive Computational Fluid Dynamics (CFD) methods for the numerical simulation of equipment typically adopted in the chemical and process industries. The apparatuses selected for the investigation, specifically membrane modules, stirred vessels and fluidized beds, were characterized by a different and often complex fluid dynamic behaviour and in some cases the momentum transfer phenomena were coupled with mass transfer or multiphase interactions. Firs of all, a novel modelling approach based on CFD for the prediction of the gas separation process in membrane modules for hydrogen purification is developed. The reliability of the gas velocity field calculated numerically is assessed by comparison of the predictions with experimental velocity data collected by Particle Image Velocimetry, while the applicability of the model to properly predict the separation process under a wide range of operating conditions is assessed through a strict comparison with permeation experimental data. Then, the effect of numerical issues on the RANS-based predictions of single phase stirred tanks is analysed. The homogenisation process of a scalar tracer is also investigated and simulation results are compared to original passive tracer homogenisation curves determined with Planar Laser Induced Fluorescence. The capability of a CFD approach based on the solution of RANS equations is also investigated for describing the fluid dynamic characteristics of the dispersion of organics in water. Finally, an Eulerian-Eulerian fluid-dynamic model is used to simulate mono-disperse suspensions of Geldart A Group particles fluidized by a Newtonian incompressible fluid as well as binary segregating fluidized beds of particles differing in size and density. The results obtained under a number of different operating conditions are compared with literature experimental data and the effect of numerical uncertainties on axial segregation is also discussed.

Evaluation of Microbial Contamination in Bivalve Mollusks: Epidemiology and Diagnosis

Shellfish are filter-feeding organisms that can accumulate many bacteria and viruses. Considering that depuration procedures are not effective in removal of certain microorganisms, shellfish-borne diseases are frequent in many parts of the world, and their control must rely primarily on investigation of prevalence of human pathogens in shellfish and water environment. However, the diffusion of enteric viruses and Vibrio bacteria is not known in many geographical areas, for example in Sardinia, Italy. A survey aimed at investigating the prevalence of Norovirus (NoV), hepatitis A virus (HAV), V. parahaemolyticus, V. cholerae and V. vulnificus was carried out, analyzing both local and imported purified, non-purified and retail shellfish from North Italy and Sardinia. Shellfish from both areas were found contaminated by NoVs, HAV and Vibrio, including retail and purified animals. Molecular analysis evidenced different NoV genogroups and genotypes, including bovine NoVs, as well as pathogenic Vibrio strains, underlining the risk for shellfish consumers. However, also other approaches are needed to control the diffusion of shellfish-borne diseases. It was originally thought that enteric viruses are passively accumulated by shellfish. Recently, it was proven that NoVs bind to specific carbohydrate ligands in oysters, and various NoV strains are characterized by a different bioaccumulation pattern. To deepen the knowledge on this argument, a study was carried out, analyzing bioaccumulation of up to 8 different NoV strains in four different species of shellfish. Different bioaccumulation patterns were observed for each shellfish species and NoV strain used, potentially important in setting up effective shellfish purification protocols. Finally, a novel study of evaluation of viral contamination in shellfish from the French Atlantic coast was carried out following the passage of Xynthia tempest over Western Europe which caused massive destruction. Different enteric viruses were found over a one month period, evidencing the potential of these events of contaminating shellfish.

Practical implications of aflatoxin contamination in corn

Aflatoxin (AFL) contamination of corn is a serious economic and food security issue. Although a variety of technical solutions for reducing AFL contamination of corn have been proposed, only a few have produced satisfactory results. A successful approach is a biocontrol strategy consisting of using non-flatoxigenic strains of Aspergillus flavus to replace indigenous AFL-producing isolates. The main objective of the present thesis was to investigate the dynamic and contamination of AFL/A. flavus in corn in Northern Italy. The study also investigated the role of the key-pest of corn, the European Corn Borer (ECB), on AFL contamination and dispersal of A. flavus propagules in corn. Finally, the study evaluated the feasibility of bioplastic-based granules entrapping a non-aflatoxigenic A. flavus strain for the biocontrol of this fungus in corn. The 2-year field study demonstrated the efficacy of the bioplastic formulation to reduce AFL contamination in corn. More precisely, although AFL contamination varied among the two years, application of 15 and 30 kg ha-1 of granules reduced AFL contamination to up 60 and 85% in 2009 and 2010 respectively. Microbiological analysis showed that the relative abundance of non-aflatoxigenic soil isolates significantly increased after 1 month from granules application (mid-May) and throughout the corn-growing season. These findings were consistent with data obtained using a bioplastic-based bait specifically developed to selectively isolate Aspergilli from soil and other environmental samples. In addition, field and laboratory evaluations showed that the level of damages produced by ECB larvae were not significantly correlated to A. flavus infestation and AFL contamination. Taking together, these findings demonstrated that AFL contamination of corn in Northern Italy was variable, but above the EU limit for human consumption. First proposed in the USA, this study showed the practical possibility of this formulation to be use for reducing AFL contamination in corn in the EU.

Application of innovative methods of source apportionment in air contamination assessment

In this work, new tools in atmospheric pollutant sampling and analysis were applied in order to go deeper in source apportionment study. The project was developed mainly by the study of atmospheric emission sources in a suburban area influenced by a municipal solid waste incinerator (MSWI), a medium-sized coastal tourist town and a motorway. Two main research lines were followed. For what concerns the first line, the potentiality of the use of PM samplers coupled with a wind select sensor was assessed. Results showed that they may be a valid support in source apportionment studies. However, meteorological and territorial conditions could strongly affect the results. Moreover, new markers were investigated, particularly focusing on the processes of biomass burning. OC revealed a good biomass combustion process indicator, as well as all determined organic compounds. Among metals, lead and aluminium are well related to the biomass combustion. Surprisingly PM was not enriched of potassium during bonfire event. The second research line consists on the application of Positive Matrix factorization (PMF), a new statistical tool in data analysis. This new technique was applied to datasets which refer to different time resolution data. PMF application to atmospheric deposition fluxes identified six main sources affecting the area. The incinerator’s relative contribution seemed to be negligible. PMF analysis was then applied to PM2.5 collected with samplers coupled with a wind select sensor. The higher number of determined environmental indicators allowed to obtain more detailed results on the sources affecting the area. Vehicular traffic revealed the source of greatest concern for the study area. Also in this case, incinerator’s relative contribution seemed to be negligible. Finally, the application of PMF analysis to hourly aerosol data demonstrated that the higher the temporal resolution of the data was, the more the source profiles were close to the real one.

Advanced polymeric materials for applications in technical equipment for snow sports

The thesis is divided in three chapters, each one covering one topic. Initially, the thermo-mechanical and impact properties of materials used for back protectors have been analysed. Dynamical mechanical analysis (DMTA) has shown that materials used for soft-shell protectors present frequency-sensitive properties. Furthermore, through impact tests, the shock absorbing characteristics of the materials have been investigated proving the differences between soft and hard-shell protectors; moreover it has been demonstrated that the materials used for soft-shell protectors maintain their protective properties after multi-impacts. The second chapter covers the effect of the visco-elastic properties of the thermoplastic polymers on the flexural and rebound behaviours of ski boots. DMTA analysis on the materials and flexural and rebound testing on the boots have been performed. A comparison of the results highlighted a correlation between the visco-elastic properties and the flexural and rebound behaviour of ski boots. The same experimental methods have been used to investigate the influence of the design on the flexural and rebound behaviours. Finally in the third chapter the thermoplastic materials employed for the construction of ski boots soles have been characterized in terms of chemical composition, hardness, crystallinity, surface roughness and coefficient of friction (COF). The results showed a relation between material hardness and grip, in particular softer materials provide more grip with respect to harder materials. On the contrary, the surface roughness has a negative effect on friction because of the decrease in contact area. The measure of grip on inclined wet surfaces showed again a relation between hardness and grip. The performance ranking of the different materials has been the same for the COF and for the slip angle tests, indicating that COF can be used as a parameter for the choice of the optimal material to be used for the soles of ski boots.