Cluster-derived Gold/Iron catalysts for environmental applications

During the last years we assisted to an exponential growth of scientific discoveries for catalysis by gold and many applications have been found for Au-based catalysts. In the literature there are several studies concerning the use of gold-based catalysts for environmental applications and good results are reported for the catalytic combustion of different volatile organic compounds (VOCs). Recently it has also been established that gold-based catalysts are potentially capable of being effectively employed in fuel cells in order to remove CO traces by preferential CO oxidation in H2-rich streams. Bi-metallic catalysts have attracted increasing attention because of their markedly different properties from either of the costituent metals, and above all their enhanced catalytic activity, selectivity and stability. In the literature there are several studies demostrating the beneficial effect due to the addition of an iron component to gold supported catalysts in terms of enhanced activity, selectivity, resistence to deactivation and prolonged lifetime of the catalyst. In this work we tried to develop a methodology for the preparation of iron stabilized gold nanoparticles with controlled size and composition, particularly in terms of obtaining an intimate contact between different phases, since it is well known that the catalytic behaviour of multi-component supported catalysts is strongly influenced by the size of the metal particles and by their reciprocal interaction. Ligand stabilized metal clusters, with nanometric dimensions, are possible precursors for the preparation of catalytically active nanoparticles with controlled dimensions and compositions. Among these, metal carbonyl clusters are quite attractive, since they can be prepared with several different sizes and compositions and, moreover, they are decomposed under very mild conditions. A novel preparation method was developed during this thesis for the preparation of iron and gold/iron supported catalysts using bi-metallic carbonyl clusters as precursors of highly dispersed nanoparticles over TiO2 and CeO2, which are widely considered two of the most suitable supports for gold nanoparticles. Au/FeOx catalysts were prepared by employing the bi-metallic carbonyl cluster salts [NEt4]4[Au4Fe4(CO)16] (Fe/Au=1) and [NEt4][AuFe4(CO)16] (Fe/Au=4), and for comparison FeOx samples were prepared by employing the homometallic [NEt4][HFe3(CO)11] cluster. These clusters were prepared by Prof. Longoni research group (Department of Physical and Inorganic Chemistry- University of Bologna). Particular attention was dedicated to the optimization of a suitable thermal treatment in order to achieve, apart from a good Au and Fe metal dispersion, also the formation of appropriate species with good catalytic properties. A deep IR study was carried out in order to understand the physical interaction between clusters and different supports and detect the occurrence of chemical reactions between them at any stage of the preparation. The characterization by BET, XRD, TEM, H2-TPR, ICP-AES and XPS was performed in order to investigate the catalysts properties, whit particular attention to the interaction between Au and Fe and its influence on the catalytic activity. This novel preparation method resulted in small gold metallic nanoparticles surrounded by highly dispersed iron oxide species, essentially in an amorphous phase, on both TiO2 and CeO2. The results presented in this thesis confirmed that FeOx species can stabilize small Au particles, since keeping costant the gold content but introducing a higher iron amount a higher metal dispersion was achieved. Partial encapsulation of gold atoms by iron species was observed since the Au/Fe surface ratio was found much lower than bulk ratio and a strong interaction between gold and oxide species, both of iron oxide and supports, was achieved. The prepared catalysts were tested in the total oxidation of VOCs, using toluene and methanol as probe molecules for aromatics and alchols, respectively, and in the PROX reaction. Different performances were observed on titania and ceria catalysts, on both toluene and methanol combustion. Toluene combustion on titania catalyst was found to be enhanced increasing iron loading while a moderate effect on FeOx-Ti activity was achieved by Au addition. In this case toluene combustion was improved due to a higher oxygen mobility depending on enhanced oxygen activation by FeOx and Au/FeOx dispersed on titania. On the contrary ceria activity was strongly decreased in the presence of FeOx, while the introduction of gold was found to moderate the detrimental effect of iron species. In fact, excellent ceria performances are due to its ability to adsorb toluene and O2. Since toluene activation is the determining factor for its oxidation, the partial coverage of ceria sites, responsible of toluene adsorption, by FeOx species finely dispersed on the surface resulted in worse efficiency in toluene combustion. Better results were obtained for both ceria and titania catalysts on methanol total oxidation. In this case, the performances achieved on differently supported catalysts indicate that the oxygen mobility is the determining factor in this reaction. The introduction of gold on both TiO2 and CeO2 catalysts, lead to a higher oxygen mobility due to the weakening of both Fe-O and Ce-O bonds and consequently to enhanced methanol combustion. The catalytic activity was found to strongly depend on oxygen mobility and followed the same trend observed for catalysts reducibility. Regarding CO PROX reaction, it was observed that Au/FeOx titania catalysts are less active than ceria ones, due to the lower reducibility of titania compared to ceria. In fact the availability of lattice oxygen involved in PROX reaction is much higher in the latter catalysts. However, the CO PROX performances observed for ceria catalysts are not really high compared to data reported in literature, probably due to the very low Au/Fe surface ratio achieved with this preparation method. CO preferential oxidation was found to strongly depend on Au particle size but also on surface oxygen reducibility, depending on the different oxide species which can be formed using different thermal treatment conditions or varying the iron loading over the support.

Architectures and design patterns for functional design of logic control and diagnostics in industrial automation

Recently in most of the industrial automation process an ever increasing degree of automation has been observed. This increasing is motivated by the higher requirement of systems with great performance in terms of quality of products/services generated, productivity, efficiency and low costs in the design, realization and maintenance. This trend in the growth of complex automation systems is rapidly spreading over automated manufacturing systems (AMS), where the integration of the mechanical and electronic technology, typical of the Mechatronics, is merging with other technologies such as Informatics and the communication networks. An AMS is a very complex system that can be thought constituted by a set of flexible working stations, one or more transportation systems. To understand how this machine are important in our society let considerate that every day most of us use bottles of water or soda, buy product in box like food or cigarets and so on. Another important consideration from its complexity derive from the fact that the the consortium of machine producers has estimated around 350 types of manufacturing machine. A large number of manufacturing machine industry are presented in Italy and notably packaging machine industry,in particular a great concentration of this kind of industry is located in Bologna area; for this reason the Bologna area is called “packaging valley”. Usually, the various parts of the AMS interact among them in a concurrent and asynchronous way, and coordinate the parts of the machine to obtain a desiderated overall behaviour is an hard task. Often, this is the case in large scale systems, organized in a modular and distributed manner. Even if the success of a modern AMS from a functional and behavioural point of view is still to attribute to the design choices operated in the definition of the mechanical structure and electrical electronic architecture, the system that governs the control of the plant is becoming crucial, because of the large number of duties associated to it. Apart from the activity inherent to the automation of themachine cycles, the supervisory system is called to perform other main functions such as: emulating the behaviour of traditional mechanical members thus allowing a drastic constructive simplification of the machine and a crucial functional flexibility; dynamically adapting the control strategies according to the different productive needs and to the different operational scenarios; obtaining a high quality of the final product through the verification of the correctness of the processing; addressing the operator devoted to themachine to promptly and carefully take the actions devoted to establish or restore the optimal operating conditions; managing in real time information on diagnostics, as a support of the maintenance operations of the machine. The kind of facilities that designers can directly find on themarket, in terms of software component libraries provides in fact an adequate support as regard the implementation of either top-level or bottom-level functionalities, typically pertaining to the domains of user-friendly HMIs, closed-loop regulation and motion control, fieldbus-based interconnection of remote smart devices. What is still lacking is a reference framework comprising a comprehensive set of highly reusable logic control components that, focussing on the cross-cutting functionalities characterizing the automation domain, may help the designers in the process of modelling and structuring their applications according to the specific needs. Historically, the design and verification process for complex automated industrial systems is performed in empirical way, without a clear distinction between functional and technological-implementation concepts and without a systematic method to organically deal with the complete system. Traditionally, in the field of analog and digital control design and verification through formal and simulation tools have been adopted since a long time ago, at least for multivariable and/or nonlinear controllers for complex time-driven dynamics as in the fields of vehicles, aircrafts, robots, electric drives and complex power electronics equipments. Moving to the field of logic control, typical for industrial manufacturing automation, the design and verification process is approached in a completely different way, usually very “unstructured”. No clear distinction between functions and implementations, between functional architectures and technological architectures and platforms is considered. Probably this difference is due to the different “dynamical framework”of logic control with respect to analog/digital control. As a matter of facts, in logic control discrete-events dynamics replace time-driven dynamics; hence most of the formal and mathematical tools of analog/digital control cannot be directly migrated to logic control to enlighten the distinction between functions and implementations. In addition, in the common view of application technicians, logic control design is strictly connected to the adopted implementation technology (relays in the past, software nowadays), leading again to a deep confusion among functional view and technological view. In Industrial automation software engineering, concepts as modularity, encapsulation, composability and reusability are strongly emphasized and profitably realized in the so-calledobject-oriented methodologies. Industrial automation is receiving lately this approach, as testified by some IEC standards IEC 611313, IEC 61499 which have been considered in commercial products only recently. On the other hand, in the scientific and technical literature many contributions have been already proposed to establish a suitable modelling framework for industrial automation. During last years it was possible to note a considerable growth in the exploitation of innovative concepts and technologies from ICT world in industrial automation systems. For what concerns the logic control design, Model Based Design (MBD) is being imported in industrial automation from software engineering field. Another key-point in industrial automated systems is the growth of requirements in terms of availability, reliability and safety for technological systems. In other words, the control system should not only deal with the nominal behaviour, but should also deal with other important duties, such as diagnosis and faults isolations, recovery and safety management. Indeed, together with high performance, in complex systems fault occurrences increase. This is a consequence of the fact that, as it typically occurs in reliable mechatronic systems, in complex systems such as AMS, together with reliable mechanical elements, an increasing number of electronic devices are also present, that are more vulnerable by their own nature. The diagnosis problem and the faults isolation in a generic dynamical system consists in the design of an elaboration unit that, appropriately processing the inputs and outputs of the dynamical system, is also capable of detecting incipient faults on the plant devices, reconfiguring the control system so as to guarantee satisfactory performance. The designer should be able to formally verify the product, certifying that, in its final implementation, it will perform itsrequired function guarantying the desired level of reliability and safety; the next step is that of preventing faults and eventually reconfiguring the control system so that faults are tolerated. On this topic an important improvement to formal verification of logic control, fault diagnosis and fault tolerant control results derive from Discrete Event Systems theory. The aimof this work is to define a design pattern and a control architecture to help the designer of control logic in industrial automated systems. The work starts with a brief discussion on main characteristics and description of industrial automated systems on Chapter 1. In Chapter 2 a survey on the state of the software engineering paradigm applied to industrial automation is discussed. Chapter 3 presentes a architecture for industrial automated systems based on the new concept of Generalized Actuator showing its benefits, while in Chapter 4 this architecture is refined using a novel entity, the Generalized Device in order to have a better reusability and modularity of the control logic. In Chapter 5 a new approach will be present based on Discrete Event Systems for the problemof software formal verification and an active fault tolerant control architecture using online diagnostic. Finally conclusive remarks and some ideas on new directions to explore are given. In Appendix A are briefly reported some concepts and results about Discrete Event Systems which should help the reader in understanding some crucial points in chapter 5; while in Appendix B an overview on the experimental testbed of the Laboratory of Automation of University of Bologna, is reported to validated the approach presented in chapter 3, chapter 4 and chapter 5. In Appendix C some components model used in chapter 5 for formal verification are reported.

Multifunctional nanocarriers encapsulating anti-Alzheimer drug for nasal delivery to central nervous system

Alzheimer's disease (AD) is a fatal neurodegenerative condition characterized clinically by progressive memory loss and irreversible cognitive deterioration. It has been shown that there is a progressive degeneration of the brain cholinergic neurons which leads to the appearance of cognitive symptoms of the disease. The aim of this work was the formulation of multifunctional nanocarriers for nasal administration of tacrine-HCl (THA). This route has many advantages; in particular is possible to convey the drug directly to the Central Nervous System, through the olfactory bulb. In particular, were prepared Albumin nanoparticles carrying beta cyclodextrin and two different beta cyclodextrin derivatives (hydroxypropyl beta cyclodextrin and sulphobutylether beta cyclodextrin), and Multifunctional liposomes, prepared using traditional excipients (cholesterol and phosphatidylcholine), partly enriched with α-tocopherol (Toc) and/or polyunsaturated fatty acids (eicosapentaenoic acid and docosahexaenoic acid) (Ω3). Both nanosystems were characterized in terms of size, Zeta potential and encapsulation efficiency. Were also evaluated their functional properties such as mucoadhesion and permeability, using an ex-vivo assay based on nasal sheep mucosa. On Liposomes were also assessed drug neuronal uptake, cell toxicity, antioxidant and, cytoprotective activity in the human neuronal cell line SH-SY5Y and finally tocopherol trans-membrane diffusion. Both the nanocarriers produced presented excellent properties and a high potential as new systems for CNS-delivery of anti-Alzheimer drugs via the nasal route.

Conservazione del seme sortato di suino

Gli spermatozoi di suino sottoposti alla procedura di sessaggio mediante citofluorimetria presentano una serie di modificazioni morfo-funzionali che compromettono nel tempo la loro sopravvivenza e la capacità fecondante. Questi spermatozoi, inoltre, a causa della sensibilità ai danni indotti dalla crioconservazione, vengono solitamente conservati allo stato liquido a 15-17°C, con conseguente ulteriore peggioramento nel tempo della qualità delle cellule spermatiche sessate. Lo scopo della ricerca è stato quello di valutare le modificazioni di alcune caratteristiche morfo-funzionali degli spermatozoi in seguito a sex-sorting e conseguente conservazione. Successivamente si è cercato di migliorare i parametri qualitativi del seme sessato mediante l’aggiunta di sostanze antiossidanti e la messa a punto di una nuova metodica di conservazione. I risultati ottenuti hanno evidenziato che la procedura di sessaggio e la conseguente conservazione per 24-26 ore a 15°C hanno indotto un peggioramento significativo delle caratteristiche morfo-funzionali (vitalità, integrità acrosomiale, quantità e distribuzione dell’Hsp70, capacità fecondante). Mentre l’azione degli antiossidanti non si è rivelata efficace nel miglioramento della qualità degli spermatozoi durante le fasi di colorazione e passaggio attraverso il citofluorimetro, l’azione congiunta del plasma seminale e degli antiossidanti superossido-dismutasi ed epigallocatechina-3-gallato ha indotto un miglioramento significativo della vitalità degli spermatozoi. Per la conservazione del seme di suino è stata testata la tecnica di incapsulazione in membrane di alginato di bario che permette, durante l’inseminazione artificiale, un rilascio graduale degli spermatozoi e l’utilizzo di un quantitativo inferiore di materiale seminale. L’applicazione di tale tecnica per la conservazione degli spermatozoi di suino sessati non sembra provocare un calo significativo della vitalità, dell’integrità acrosomiale e dell’efficienza totale di fecondazione rispetto al seme sortato e conservato diluito suggerendo futuri studi in vivo. Una migliore conoscenza dei danni indotti da queste tecnologie e la loro minimizzazione potrà stimolare in futuro l’utilizzo su vasta scala del seme sessato nel suino.

3D nanostructured microcarriers for cell therapy in regenerative medicine

Supercritical Emulsion Extraction technology (SEE-C) was proposed for the production of poly-lactic-co-glycolic acid microcarriers. SEE-C operating parameters as pressure, temperature and flow rate ratios were analyzed and the process performance was optimized in terms of size distribution and encapsulation efficiency. Microdevices loaded with bovine serum insulin were produced with different sizes (2 and 3 µm) or insulin charges (3 and 6 mg/g) and with an encapsulation efficiency of 60%. The microcarriers were characterized in terms of insulin release profile in two different media (PBS and DMEM) and the diffusion and degradation constants were also estimated by using a mathematical model. PLGA microdevices were also used in a cultivation of embryonic ventricular myoblasts (cell line H9c2 obtained from rat) in a FBS serum free medium to monitor cell viability and growth in dependence of insulin released. Good cell viability and growth were observed on 3 µm microdevices loaded with 3 mg/g of insulin. PLGA microspheres loaded with growth factors (GFs) were charged into alginate scaffold with human Mesenchimal Steam Cells (hMSC) for bone tissue engineering with the aim of monitoring the effect of the local release of these signals on cells differentiation. These “living” 3D scaffolds were incubated in a direct perfusion tubular bioreactor to enhance nutrient transport and exposing the cells to a given shear stress. Different GFs such as, h-VEGF, h-BMP2 and a mix of two (ratio 1:1) were loaded and alginate beads were recovered from dynamic (tubular perfusion system bioreactor) and static culture at different time points (1st, 7th, 21st days) for the analytical assays such as, live/dead; alkaline phosphatase; osteocalcin; osteopontin and Van Kossa Immunoassay. The immunoassay confirmed always a better cells differentiation in the bioreactor with respect to the static culture and revealed a great influence of the BMP-2 released in the scaffold on cell differentiation.

Spectroscopic studies on Cyclodextrin and Metal Organic Framework based potential nanovectors for delivery of Anticancer and Antiviral drugs

The aim of this work is to contribute to the development of new multifunctional nanocarriers for improved encapsulation and delivery of anticancer and antiviral drugs. The work focused on water soluble and biocompatible oligosaccharides, the cyclodextrins (CyDs), and a new family of nanostructured, biodegradable carrier materials made of porous metal-organic frameworks (nanoMOFs). The drugs of choice were the anticancer doxorubicin (DOX), azidothymidine (AZT) and its phosphate derivatives and artemisinin (ART). DOX possesses a pharmacological drawback due to its self-aggregation tendency in water. The non covalent binding of DOX to a series of CyD derivatives, such as g-CyD, an epichlorohydrin crosslinked b-CyD polymer (pb-CyD) and a citric acid crosslinked g-CyD polymer (pg-CyD) was studied by UV visible absorption, circular dichroism and fluorescence. Multivariate global analysis of multiwavelength data from spectroscopic titrations allowed identification and characterization of the stable complexes. pg-CyD proved to be the best carrier showing both high association constants and ability to monomerize DOX. AZT is an important antiretroviral drug. The active form is AZT-triphosphate (AZT-TP), formed in metabolic paths of low efficiency. Direct administration of AZT-TP is limited by its poor stability in biological media. So the development of suitable carriers is highly important. In this context we studied the binding of some phosphorilated derivatives to nanoMOFs by spectroscopic methods. The results obtained with iron(III)-trimesate nanoMOFs allowed to prove that the binding of these drugs mainly occurs by strong iono-covalent bonds to iron(III) centers. On the basis of these and other results obtained in partner laboratories, it was possible to propose this highly versatile and “green” carrier system for delivery of phosphorylated nucleoside analogues. The interaction of DOX with nanoMOFs was also studied. Finally the binding of the antimalarial drug, artemisinin (ART) with two cyclodextrin-based carriers,the pb-CyD and a light responsive bis(b-CyD) host, was also studied.

A universal delta model

This thesis presents a universal model of documents and deltas. This model formalize what it means to find differences between documents and to shows a single shared formalization that can be used by any algorithm to describe the differences found between any kind of comparable documents. The main scientific contribution of this thesis is a universal delta model that can be used to represent the changes found by an algorithm. The main part of this model are the formal definition of changes (the pieces of information that records that something has changed), operations (the definitions of the kind of change that happened) and deltas (coherent summaries of what has changed between two documents). The fundamental mechanism tha makes the universal delta model a very expressive tool is the use of encapsulation relations between changes. In the universal delta model, changes are not always simple records of what has changed, they can also be combined into more complex changes that reflects the detection of more meaningful modifications. In addition to the main entities (i.e., changes, operations and deltas), the model describes and defines also documents and the concept of equivalence between documents. As a corollary to the model, there is also an extensible catalog of possible operations that algorithms can detect, used to create a common library of operations, and an UML serialization of the model, useful as a reference when implementing APIs that deal with deltas. The universal delta model presented in this thesis acts as the formal groundwork upon which algorithm can be based and libraries can be implemented. It removes the need to recreate a new delta model and terminology whenever a new algorithm is devised. It also alleviates the problems that toolmakers have when adapting their software to new diff algorithms.

Strategie formulative per la veicolazione nasale di farmaci

Microparticelle a base di complessi polielettrolitici di Chitosano/Pectina per il rilascio nasale di Tacrina cloridrato. Lo scopo di questo studio è stata la ricerca di nuove formulazioni solide per la somministrazione nasale di Tacrina cloridrato allo scopo di ridurre l’eccessivo effetto di primo passaggio epatico ed aumentarne la biodisponibilità a livello del Sistema Nervoso Centrale. La Tacrina è stata incapsulata in microparticelle mucoadesive a base di complessi elettrolitici di chitosano e pectina. Le microparticelle sono state preparate mediante due diversi approcci tecnologici (spray-drying e spray-drying/liofilizzazione) e analizzate in termini di caratteristiche dimensionali, morfologiche e chimico-fisiche. Nanoparticelle di Chitosano reticolate con Sodio Cromoglicato per il trattamento della rinite allergica. Il Sodio Cromoglicato è uno dei farmaci utilizzati per il trattamento della rinite allergica. Come noto, la clearance mucociliare provoca una rapida rimozione dei farmaci in soluzione dalla cavità nasale, aumentando così il numero di somministrazioni giornaliere e, di conseguenza, riducendo la compliance del paziente. Per ovviare a tale problema, si è pensato di includere il sodio cromoglicato in nanoparticelle di chitosano, un polimero capace di aderire alla mucosa nasale, prolungare il contatto della formulazione con il sito di applicazione e ridurre il numero di somministrazioni giornaliere. Le nanoparticelle ottenute sono state caratterizzate in termini di dimensioni, resa, efficienza di incapsulazione e caricamento del farmaco, potenziale zeta e caratteristiche mucoadesive. Analisi quantitativa di Budesonide amorfa tramite calorimetria a scansione differenziale. È stato sviluppato un nuovo metodo quantitativo allo stato solido basato sulla Calorimetria a Scansione Differenziale (DSC) in grado di quantificare in modo selettivo e accurato la quantità di Budesonide amorfa presente in una miscela solida. Durante lo sviluppo del metodo sono stati affrontati problemi relativi alla convalida di metodi analitici su campioni solidi quali la miscelazione di polveri solide per la preparazione di miscele standard e il calcolo della precisione.