Models for the study of neuronal activity during cognitive tasks

Assessment of brain connectivity among different brain areas during cognitive or motor tasks is a crucial problem in neuroscience today. Aim of this research study is to use neural mass models to assess the effect of various connectivity patterns in cortical EEG power spectral density (PSD), and investigate the possibility to derive connectivity circuits from EEG data. To this end, two different models have been built. In the first model an individual region of interest (ROI) has been built as the parallel arrangement of three populations, each one exhibiting a unimodal spectrum, at low, medium or high frequency. Connectivity among ROIs includes three parameters, which specify the strength of connection in the different frequency bands. Subsequent studies demonstrated that a single population can exhibit many different simultaneous rhythms, provided that some of these come from external sources (for instance, from remote regions). For this reason in the second model an individual ROI is simulated only with a single population. Both models have been validated by comparing the simulated power spectral density with that computed in some cortical regions during cognitive and motor tasks. Another research study is focused on multisensory integration of tactile and visual stimuli in the representation of the near space around the body (peripersonal space). This work describes an original neural network to simulate representation of the peripersonal space around the hands, in basal conditions and after training with a tool used to reach the far space. The model is composed of three areas for each hand, two unimodal areas (visual and tactile) connected to a third bimodal area (visual-tactile), which is activated only when a stimulus falls within the peripersonal space. Results show that the peripersonal space, which includes just a small visual space around the hand in normal conditions, becomes elongated in the direction of the tool after training, thanks to a reinforcement of synapses.

Multiresolution spherical wavelet analysis in global seismic tomography

Every seismic event produces seismic waves which travel throughout the Earth. Seismology is the science of interpreting measurements to derive information about the structure of the Earth. Seismic tomography is the most powerful tool for determination of 3D structure of deep Earth's interiors. Tomographic models obtained at the global and regional scales are an underlying tool for determination of geodynamical state of the Earth, showing evident correlation with other geophysical and geological characteristics. The global tomographic images of the Earth can be written as a linear combinations of basis functions from a specifically chosen set, defining the model parameterization. A number of different parameterizations are commonly seen in literature: seismic velocities in the Earth have been expressed, for example, as combinations of spherical harmonics or by means of the simpler characteristic functions of discrete cells. With this work we are interested to focus our attention on this aspect, evaluating a new type of parameterization, performed by means of wavelet functions. It is known from the classical Fourier theory that a signal can be expressed as the sum of a, possibly infinite, series of sines and cosines. This sum is often referred as a Fourier expansion. The big disadvantage of a Fourier expansion is that it has only frequency resolution and no time resolution. The Wavelet Analysis (or Wavelet Transform) is probably the most recent solution to overcome the shortcomings of Fourier analysis. The fundamental idea behind this innovative analysis is to study signal according to scale. Wavelets, in fact, are mathematical functions that cut up data into different frequency components, and then study each component with resolution matched to its scale, so they are especially useful in the analysis of non stationary process that contains multi-scale features, discontinuities and sharp strike. Wavelets are essentially used in two ways when they are applied in geophysical process or signals studies: 1) as a basis for representation or characterization of process; 2) as an integration kernel for analysis to extract information about the process. These two types of applications of wavelets in geophysical field, are object of study of this work. At the beginning we use the wavelets as basis to represent and resolve the Tomographic Inverse Problem. After a briefly introduction to seismic tomography theory, we assess the power of wavelet analysis in the representation of two different type of synthetic models; then we apply it to real data, obtaining surface wave phase velocity maps and evaluating its abilities by means of comparison with an other type of parametrization (i.e., block parametrization). For the second type of wavelet application we analyze the ability of Continuous Wavelet Transform in the spectral analysis, starting again with some synthetic tests to evaluate its sensibility and capability and then apply the same analysis to real data to obtain Local Correlation Maps between different model at same depth or between different profiles of the same model.

Using national FADN database to describe Italian farms and arable fields. A comparison of sustainability level between organic versus conventional regimes.

The study defines a new farm classification and identifies the arable land management. These aspects and several indicators are taken into account to estimate the sustainability level of farms, for organic and conventional regimes. The data source is Italian Farm Account Data Network (RICA) for years 2007-2011, which samples structural and economical information. An environmental data has been added to the previous one to better describe the farm context. The new farm classification describes holding by general informations and farm structure. The general information are: adopted regime and farm location in terms of administrative region, slope and phyto-climatic zone. The farm structures describe the presence of main productive processes and land covers, which are recorded by FADN database. The farms, grouped by homogeneous farm structure or farm typology, are evaluated in terms of sustainability. The farm model MAD has been used to estimate a list of indicators. They describe especially environmental and economical areas of sustainability. Finally arable lands are taken into account to identify arable land managements and crop rotations. Each arable land has been classified by crop pattern. Then crop rotation management has been analysed by spatial and temporal approaches. The analysis reports a high variability inside regimes. The farm structure influences indicators level more than regimes, and it is not always possible to compare the two regimes. However some differences between organic and conventional agriculture have been found. Organic farm structures report different frequency and geographical location than conventional ones. Also different connections among arable lands and farm structures have been identified.

The Moho reflectivity from ambient seismic noise autocorrelations beneath the Western Alps

The lower crustal structure beneath the Western Alps -- including the Moho -- bears the signature of past and present geodynamic processes. It has been the subject of many studies until now. However, its current knowledge still leaves significant open questions. In order to derive new information, independent from previous determinations, here I wish to address this topic using a different method --- ambient seismic noise autocorrelation --- that is for the first time applied to reveal Moho depth in the Western Alps. Moho reflections are identified by picking reflectivity changes in ambient seismic noise autocorrelations. The seismic data is retrieved from more than 200 broadband seismic stations, from the China--Italy--France Alps (CIFALPS) linear seismic network, and from a subset of the AlpArray Seismic Network (AASN). The automatically-picked reflectivity changes along the CIFALPS transect in the southwestern Alps show the best results in the 0.5--1 Hz frequency band. The autocorrelation reflectivity profile of the CIFALPS transect shows a steeper subduction profile,~55 to ~70 km, of the European Plate underneath the Adriatic Plate. The dense spacing of the CIFALPS network facilitates the detection of lateral continuity of crustal structure, and of the Ivrea mantle wedge reaching shallow crustal depths in the southwestern Alps. The data of the AASN stations are filtered in the 0.4--1 and 0.5--1 Hz frequency bands. Although the majority of the stations give the same Moho depth for the different frequency bands, the few stations with different Moho depths shows the care that has to be taken when choosing the frequency band for filtering the autocorrelation stacks. The new Moho depth maps by using the AASN stations are a compilation of the first and second picked reflectivity changes. The results show the complex crust-mantle structure with clear differences between the northwestern and southwestern Alps.

Characterization and modeling of low-frequency noise in MOSFETs

For many years, RF and analog integrated circuits have been mainly developed using bipolar and compound semiconductor technologies due to their better performance. In the last years, the advance made in CMOS technology allowed analog and RF circuits to be built with such a technology, but the use of CMOS technology in RF application instead of bipolar technology has brought more issues in terms of noise. The noise cannot be completely eliminated and will therefore ultimately limit the accuracy of measurements and set a lower limit on how small signals can be detected and processed in an electronic circuit. One kind of noise which affects MOS transistors much more than bipolar ones is the low-frequency noise. In MOSFETs, low-frequency noise is mainly of two kinds: flicker or 1/f noise and random telegraph signal noise (RTS). The objective of this thesis is to characterize and to model the low-frequency noise by studying RTS and flicker noise under both constant and switched bias conditions. The effect of different biasing schemes on both RTS and flicker noise in time and frequency domain has been investigated.

Different approaches to identify markers for meat quality and production traits in pigs: analysis of the transcriptome in post mortem skeletal muscle and investigation of candidate genes

Due to the growing attention of consumers towards their food, improvement of quality of animal products has become one of the main focus of research. To this aim, the application of modern molecular genetics approaches has been proved extremely useful and effective. This innovative drive includes all livestock species productions, including pork. The Italian pig breeding industry is unique because needs heavy pigs slaughtered at about 160 kg for the production of high quality processed products. For this reason, it requires precise meat quality and carcass characteristics. Two aspects have been considered in this thesis: the application of the transcriptome analysis in post mortem pig muscles as a possible method to evaluate meat quality parameters related to the pre mortem status of the animals, including health, nutrition, welfare, and with potential applications for product traceability (chapters 3 and 4); the study of candidate genes for obesity related traits in order to identify markers associated with fatness in pigs that could be applied to improve carcass quality (chapters 5, 6, and 7). Chapter three addresses the first issue from a methodological point of view. When we considered this issue, it was not obvious that post mortem skeletal muscle could be useful for transcriptomic analysis. Therefore we demonstrated that the quality of RNA extracted from skeletal muscle of pigs sampled at different post mortem intervals (20 minutes, 2 hours, 6 hours, and 24 hours) is good for downstream applications. Degradation occurred starting from 48 h post mortem even if at this time it is still possible to use some RNA products. In the fourth chapter, in order to demonstrate the potential use of RNA obtained up to 24 hours post mortem, we present the results of RNA analysis with the Affymetrix microarray platform that made it possible to assess the level of expression of more of 24000 mRNAs. We did not identify any significant differences between the different post mortem times suggesting that this technique could be applied to retrieve information coming from the transcriptome of skeletal muscle samples not collected just after slaughtering. This study represents the first contribution of this kind applied to pork. In the fifth chapter, we investigated as candidate for fat deposition the TBC1D1 [TBC1 (tre-2/USP6, BUB2, cdc16) gene. This gene is involved in mechanisms regulating energy homeostasis in skeletal muscle and is associated with predisposition to obesity in humans. By resequencing a fragment of the TBC1D1 gene we identified three synonymous mutations localized in exon 2 (g.40A>G, g.151C>T, and g.172T>C) and 2 polymorphisms localized in intron 2 (g.219G>A and g.252G>A). One of these polymorphisms (g.219G>A) was genotyped by high resolution melting (HRM) analysis and PCR-RFLP. Moreover, this gene sequence was mapped by radiation hybrid analysis on porcine chromosome 8. The association study was conducted in 756 performance tested pigs of Italian Large White and Italian Duroc breeds. Significant results were obtained for lean meat content, back fat thickness, visible intermuscular fat and ham weight. In chapter six, a second candidate gene (tribbles homolog 3, TRIB3) is analyzed in a study of association with carcass and meat quality traits. The TRIB3 gene is involved in energy metabolism of skeletal muscle and plays a role as suppressor of adipocyte differentiation. We identified two polymorphisms in the first coding exon of the porcine TRIB3 gene, one is a synonymous SNP (c.132T> C), a second is a missense mutation (c.146C> T, p.P49L). The two polymorphisms appear to be in complete linkage disequilibrium between and within breeds. The in silico analysis of the p.P49L substitution suggests that it might have a functional effect. The association study in about 650 pigs indicates that this marker is associated with back fat thickness in Italian Large White and Italian Duroc breeds in two different experimental designs. This polymorphisms is also associated with lactate content of muscle semimembranosus in Italian Large White pigs. Expression analysis indicated that this gene is transcribed in skeletal muscle and adipose tissue as well as in other tissues. In the seventh chapter, we reported the genotyping results for of 677 SNPs in extreme divergent groups of pigs chosen according to the extreme estimated breeding values for back fat thickness. SNPs were identified by resequencing, literature mining and in silico database mining. analysis, data reported in the literature of 60 candidates genes for obesity. Genotyping was carried out using the GoldenGate (Illumina) platform. Of the analyzed SNPs more that 300 were polymorphic in the genotyped population and had minor allele frequency (MAF) >0.05. Of these SNPs, 65 were associated (P<0.10) with back fat thickness. One of the most significant gene marker was the same TBC1D1 SNPs reported in chapter 5, confirming the role of this gene in fat deposition in pig. These results could be important to better define the pig as a model for human obesity other than for marker assisted selection to improve carcass characteristics.

Dynamic identification of structures: experimental assessment of modal parameteres through methods in frequency domain, in time-frequency domain and model updating

Among the experimental methods commonly used to define the behaviour of a full scale system, dynamic tests are the most complete and efficient procedures. A dynamic test is an experimental process, which would define a set of characteristic parameters of the dynamic behaviour of the system, such as natural frequencies of the structure, mode shapes and the corresponding modal damping values associated. An assessment of these modal characteristics can be used both to verify the theoretical assumptions of the project, to monitor the performance of the structural system during its operational use. The thesis is structured in the following chapters: The first introductive chapter recalls some basic notions of dynamics of structure, focusing the discussion on the problem of systems with multiply degrees of freedom (MDOF), which can represent a generic real system under study, when it is excited with harmonic force or in free vibration. The second chapter is entirely centred on to the problem of dynamic identification process of a structure, if it is subjected to an experimental test in forced vibrations. It first describes the construction of FRF through classical FFT of the recorded signal. A different method, also in the frequency domain, is subsequently introduced; it allows accurately to compute the FRF using the geometric characteristics of the ellipse that represents the direct input-output comparison. The two methods are compared and then the attention is focused on some advantages of the proposed methodology. The third chapter focuses on the study of real structures when they are subjected to experimental test, where the force is not known, like in an ambient or impact test. In this analysis we decided to use the CWT, which allows a simultaneous investigation in the time and frequency domain of a generic signal x(t). The CWT is first introduced to process free oscillations, with excellent results both in terms of frequencies, dampings and vibration modes. The application in the case of ambient vibrations defines accurate modal parameters of the system, although on the damping some important observations should be made. The fourth chapter is still on the problem of post processing data acquired after a vibration test, but this time through the application of discrete wavelet transform (DWT). In the first part the results obtained by the DWT are compared with those obtained by the application of CWT. Particular attention is given to the use of DWT as a tool for filtering the recorded signal, in fact in case of ambient vibrations the signals are often affected by the presence of a significant level of noise. The fifth chapter focuses on another important aspect of the identification process: the model updating. In this chapter, starting from the modal parameters obtained from some environmental vibration tests, performed by the University of Porto in 2008 and the University of Sheffild on the Humber Bridge in England, a FE model of the bridge is defined, in order to define what type of model is able to capture more accurately the real dynamic behaviour of the bridge. The sixth chapter outlines the necessary conclusions of the presented research. They concern the application of a method in the frequency domain in order to evaluate the modal parameters of a structure and its advantages, the advantages in applying a procedure based on the use of wavelet transforms in the process of identification in tests with unknown input and finally the problem of 3D modeling of systems with many degrees of freedom and with different types of uncertainty.

Foetal heart rate recording: analysis and comparison of different methodologies

Monitoring foetal health is a very important task in clinical practice to appropriately plan pregnancy management and delivery. In the third trimester of pregnancy, ultrasound cardiotocography is the most employed diagnostic technique: foetal heart rate and uterine contractions signals are simultaneously recorded and analysed in order to ascertain foetal health. Because ultrasound cardiotocography interpretation still lacks of complete reliability, new parameters and methods of interpretation, or alternative methodologies, are necessary to further support physicians’ decisions. To this aim, in this thesis, foetal phonocardiography and electrocardiography are considered as different techniques. Further, variability of foetal heart rate is thoroughly studied. Frequency components and their modifications can be analysed by applying a time-frequency approach, for a distinct understanding of the spectral components and their change over time related to foetal reactions to internal and external stimuli (such as uterine contractions). Such modifications of the power spectrum can be a sign of autonomic nervous system reactions and therefore represent additional, objective information about foetal reactivity and health. However, some limits of ultrasonic cardiotocography still remain, such as in long-term foetal surveillance, which is often recommendable mainly in risky pregnancies. In these cases, the fully non-invasive acoustic recording, foetal phonocardiography, through maternal abdomen, represents a valuable alternative to the ultrasonic cardiotocography. Unfortunately, the so recorded foetal heart sound signal is heavily loaded by noise, thus the determination of the foetal heart rate raises serious signal processing issues. A new algorithm for foetal heart rate estimation from foetal phonocardiographic recordings is presented in this thesis. Different filtering and enhancement techniques, to enhance the first foetal heart sounds, were applied, so that different signal processing techniques were implemented, evaluated and compared, by identifying the strategy characterized on average by the best results. In particular, phonocardiographic signals were recorded simultaneously to ultrasonic cardiotocographic signals in order to compare the two foetal heart rate series (the one estimated by the developed algorithm and the other provided by cardiotocographic device). The algorithm performances were tested on phonocardiographic signals recorded on pregnant women, showing reliable foetal heart rate signals, very close to the ultrasound cardiotocographic recordings, considered as reference. The algorithm was also tested by using a foetal phonocardiographic recording simulator developed and presented in this research thesis. The target was to provide a software for simulating recordings relative to different foetal conditions and recordings situations and to use it as a test tool for comparing and assessing different foetal heart rate extraction algorithms. Since there are few studies about foetal heart sounds time characteristics and frequency content and the available literature is poor and not rigorous in this area, a data collection pilot study was also conducted with the purpose of specifically characterising both foetal and maternal heart sounds. Finally, in this thesis, the use of foetal phonocardiographic and electrocardiographic methodology and their combination, are presented in order to detect foetal heart rate and other functioning anomalies. The developed methodologies, suitable for longer-term assessment, were able to detect heart beat events correctly, such as first and second heart sounds and QRS waves. The detection of such events provides reliable measures of foetal heart rate, potentially information about measurement of the systolic time intervals and foetus circulatory impedance.

Toward a Magnitude Scale for Low Frequency Seismicity The LP energy for Campi Flegrei caldera

The energy released during a seismic crisis in volcanic areas is strictly related to the physical processes in the volcanic structure. In particular Long Period seismicity, that seems to be related to the oscillation of a fluid-filled crack (Chouet , 1996, Chouet, 2003, McNutt, 2005), can precedes or accompanies an eruption. The present doctoral thesis is focused on the study of the LP seismicity recorded in the Campi Flegrei volcano (Campania, Italy) during the October 2006 crisis. Campi Flegrei Caldera is an active caldera; the combination of an active magmatic system and a dense populated area make the Campi Flegrei a critical volcano. The source dynamic of LP seismicity is thought to be very different from the other kind of seismicity ( Tectonic or Volcano Tectonic): it’s characterized by a time sustained source and a low content in frequency. This features implies that the duration–magnitude, that is commonly used for VT events and sometimes for LPs as well, is unadapted for LP magnitude evaluation. The main goal of this doctoral work was to develop a method for the determination of the magnitude for the LP seismicity; it’s based on the comparison of the energy of VT event and LP event, linking the energy to the VT moment magnitude. So the magnitude of the LP event would be the moment magnitude of a VT event with the same energy of the LP. We applied this method to the LP data-set recorded at Campi Flegrei caldera in 2006, to an LP data-set of Colima volcano recorded in 2005 – 2006 and for an event recorded at Etna volcano. Experimenting this method to lots of waveforms recorded at different volcanoes we tested its easy applicability and consequently its usefulness in the routinely and in the quasi-real time work of a volcanological observatory.

Effect of different management intensities on natural and human-induced carbon fluxes in a golf course in northern Italy

Turfgrasses are ubiquitous in urban landscape and their role on carbon (C) cycle is increasing important also due to the considerable footprint related to their management practices. It is crucial to understand the mechanisms driving the C assimilation potential of these terrestrial ecosystems Several approaches have been proposed to assess C dynamics: micro-meteorological methods, small-chamber enclosure system (SC), chrono-sequence approach and various models. Natural and human-induced variables influence turfgrasses C fluxes. Species composition, environmental conditions, site characteristics, former land use and agronomic management are the most important factors considered in literature driving C sequestration potential. At the same time different approaches seem to influence C budget estimates. In order to study the effect of different management intensities on turfgrass, we estimated net ecosystem exchange (NEE) through a SC approach in a hole of a golf course in the province of Verona (Italy) for one year. The SC approach presented several advantages but also limits related to the measurement frequency, timing and duration overtime, and to the methodological errors connected to the measuring system. Daily CO2 fluxes changed according to the intensity of maintenance, likely due to different inputs and disturbances affecting biogeochemical cycles, combined also to the different leaf area index (LAI). The annual cumulative NEE decreased with the increase of the intensity of management. NEE was related to the seasonality of turfgrass, following temperatures and physiological activity. Generally on the growing season CO2 fluxes towards atmosphere exceeded C sequestered. The cumulative NEE showed a system near to a steady state for C dynamics. In the final part greenhouse gases (GHGs) emissions due to fossil fuel consumption for turfgrass upkeep were estimated, pinpointing that turfgrass may result a considerable C source. The C potential of trees and shrubs needs to be considered to obtain a complete budget.

Addressing tumor heterogeneity in esophageal adenocarcinoma through different molecular approaches

Several studies have shown epidemiologic, clinical, immune-histochemical and molecular differences among esophageal adenocarcinomas (EAC). Since pathogenesis and biology of this tumor are far to be well defined, our study aimed to examine intra- and inter-tumor heterogeneity and to solve crucial controversies through different molecular approaches. Target sequencing was performed for sorted cancer subpopulations from formalin embedded material obtained from 38 EACs, not treated with neoadjuvant therapy. 35 out 38 cases carried at least one somatic mutation, not present in the corresponding sorted stromal cells. 73.7% of cases carried mutations in TP53 and 10.5% in CDKN2A. Mutations in other genes occurred at lower frequency, including HNF1A, not previously associated with EAC. Sorting allowed us to isolate clones with different mutational loads and/or additional copy number amplifications, confirming the high intra-tumor heterogeneity of these cancers. In our cohort TP53 gene abnormalities correlated with a better survival (P = 0.028); conversely, loss of SMAD4 protein expression was associated with a higher recurrence rate (P = 0.015). Shifting the focus on the epigenetic characterization of EAC, miR-221 and miR-483-3p resulted upregulated from the MicroRNA Array card analysis and confirmed with further testing. The up-regulation of both miRNAs correlated with clinical outcomes, in particular with a reduced cancer-specific survival (miR483-3p P=0.0293; miR221 P=0.0059). In vitro analyses demonstrated an increase for miR-483-3p (fold-change=2.7) that appear to be inversely correlated with SMAD4 expression in FLO-1 cell-line. In conclusion, selective sorting allowed to define the real mutation status and to isolate different cancer subclones. MiRNA expression analysis revealed a significant up-regulation of miR-221 and miR-483-3p, which correlated with worst prognosis, implying that they can be considered oncogenic factors in EAC. Therefore, cell sorting technologies, coupled with next generation sequencing, and the analysis of microRNA profiles seem to be promising strategies to guide treatment and help classify cancer prognosis.

Study of new particle acceleration mechanisms in galaxy clusters through low frequency radio observations

Diffuse radio emission in galaxy clusters has been observed with different size and properties. Giant radio halos (RH), Mpc-size sources found in merging clusters, and mini halos (MH), 0.1-0.5 Mpc size sources located in relaxed cool-core clusters, are thought to be distinct classes of objects with different formation mechanisms. However, recent observations have revealed the unexpected presence of diffuse emission on Mpc-scales in relaxed clusters that host a central MH and show no signs of major mergers. The study of these sources is still at the beginning and it is not yet clear what could be the origin of their unusual emission. The main goal of this thesis is to test the occurrence of these peculiar sources and investigate their properties using low frequency radio observations. This thesis consists in the study of a sample of 12 cool-core galaxy clusters which present some level of dynamical disturbances on large-scale. The heterogeneity of sources in the sample allowed me to investigate under which conditions a halo-type emission is present in MH clusters; and also to study the connection between AGN bubbles and the local environment. Using high sensitivity LOFAR observations, I have detected large-scale emission in four non-merging clusters, in addition to the central MH. I have constrained for the first time the spectral properties of diffuse emission in these double radio component galaxy clusters, and I have investigated the connection between their thermal and non-thermal emission for a better comprehension of the acceleration mechanism. Furthermore, I derived upper limits to the halo power for the other clusters in the sample, which could present large-scale diffuse emission under the detection threshold. Finally, I have reconstructed the duty-cycle of one of the most powerful AGN known, located at the centre of a galaxy cluster of the sample.