Development and performance assessment of a Plasma Focus electron beam generator for Intra-Operative Radiation Therapy

The Plasma Focus is a device designed to generate a plasma sheet between two coaxial electrodes by means of a high voltage difference. The plasma is then driven to collapse into a “pinch”, where thermonuclear conditions prevail. During the “pinch phase” charged particles are emitted, with two main components: an ion beam peaked forward and an electron beam directed backward. The electron beam emitted backward by Plasma Focus devices is being investigated as a radiation source for medical applications, using it to produce x-rays by interaction with appropriate targets (through bremsstrahlung and characteristic emission). A dedicated Plasma Focus device, named PFMA-3 (Plasma Focus for Medical Applications number 3), has been designed, put in operation and tested by the research groups of the Universities of Bologna and Ferrara. The very high dose rate (several gray per discharge, in less than 1 µs) is a peculiarity of this device that has to be investigated, as it might modify the relative biological effectiveness (RBE). Aim of this Ph.D. project was to investigate the main physical properties of the low-energy x-ray beams produced by a Plasma Focus device and their potential medical applications to IORT treatments. It was necessary to develop the optimal geometrical configuration; to evaluate the x-rays produced and their dose deposited; to estimate the energy electron spectrum produced in the “pinch phase”; to study an optimal target for the conversion of the x-rays; to conduct simulations to study the physics involved; and in order to evaluate the radio-biological features of the beam, cell holders had to be developed for both irradiations and cell growth conditions.

Zirconia in dentistry

The above factors emphasize the scope of this thesis for further investigations on zirconia, the improvement of all-ceramic zirconia restorations, and especially the interaction of zirconia and veneering and its influence on the performance of the whole restoration. The introduction, chapter 1, gave a literature overview on zirconia ceramics. In chapter 2, the objective of the study was to evaluate the effect of abrading before and after sintering using alumina-based abrasives on the surface of yttria-tetragonal zirconia polycrystals. Particular attention was paid to the amount of surface stress–assisted phase transformation (tetragonal→monoclinic) and the presence of microcracks. Chapter 3 is based on the idea that the conventional sintering techniques for zirconia based materials, which are commonly used in dental reconstruction, may not provide a uniform heating, with consequent generation of microstructural flaws in the final component. As a consequence of the sintering system, using microwave heating, may represent a viable alternative. The purpose of the study was to compare the dimensional variations and physical and microstructural characteristics of commercial zirconia (Y-TZP), used as a dental restoration material, sintered in conventional and microwave furnaces. Chapter 4 described the effect of sandblasting before and after sintering on the surface roughness of zirconia and the microtensile bond strength of a pressable veneering ceramic to zirconia.

Guidelines of Special Care Dentistry in Patients with Chromosomal and Genetic syndromes

Chromosomal and genetic syndromes are frequently associated with dental and cranio-facial alterations. The aim of our study is to identify and describe the dental and craniofacial alterations typical of six genetic and chromosomal syndromes examined. Materials and Methods- A dental visit was performed to 195 patients referred from Sant’Orsola Hospital of Bologna, University of Bologna, to Service of Special Need Dentistry, Dental Clinic, Department of Biomedical and Neuromotor Science, University of Bologna. The patients recruited were 137 females and 58 males, in an age range of 3-49 years (mean age of 13.8±7.4). The total sample consisted of subjects affected with Down Syndrome (n=133), Familiar Hypophosphatemic Ricket (n=10), Muscular Dystrophies (n=12), Noonan Syndrome (n=13), Turner Syndrome (n=17), Williams Syndrome(n=10). A questionnaire regarding detailed medical and dental history, oral health and dietary habits, was filled by parents/caregivers, or patients themselves when possible. The intra-oral and extra-oral examination valued the presence of facial asymmetries, oral habits, dental and skeletal malocclusions, dental formula, dental anomalies, Plaque Index (Silness&LÖe Index), caries prevalence (dmft/DMFT index), gingivitis and periodontal disease, and mucosal lesions. Radiographic examinations (Intraoral radiographies, Orthopanoramic, Skull teleradiography) were executed according to patient’s age and treatment planning. A review of literature about each syndrome and its dental and cranio-facial characteristics and about caries, hygiene status and malocclusion prevalence on syndromic and non-syndromic population was performed. Results - The data of all the patients were collected in the “Data Collection Tables” created for each syndrome. General anamnesis information, oral hygiene habits and dmft/DMFT, PI, malocclusion prevalence were calculated and compared to syndromic and non-syndromic population results found in literature. Discussions and conclusions - Guidelines of Special Care dentistry were indicated for each syndrome, in relation to each syndrome features and individual patient characteristics.