Study of thiabendazole resistance and volatile organic compounds production of Penicillium expansum strains

The years of excessive use of thiabendazole to control Penicillium expansum has induced the development of resistance. Sensitivity of fourty eight strains collected from orchards and packinghouses in Emilia Romagna to pure and commercial TBZ was determined in vitro on TBZ amended medium (400μg/mL). Out of 48 strains, 35 were thiabendazole-sensitive (S) and 13 were thiabendazole-resistant (R). Microtiter assay adapted to P. expansum, showed EC50 values ranging from 54 to 320 μg/mL for ten TBZ-resistant strains. At the highest dose (50 μg/mL), resistant strains growth was not inhibited and the reported MICs value were >1000 μg/mL. Therefore, preliminary screening combined with microtiter assay, can be a good strategy to test susceptibility to TBZ. Mutations in the β-tubulin gene were studied on amino acid sequences from residue 167 to residue 357 of 10 P. expansum strains. Mutation at codon 198 was associated with TBZ-resistance. However, its absence in 3 resistant strains can be explained by the involvement of other mechanisms. Moreover, a P. expansum strain LB8/99 showed good antifungal effect against some fungal pathogens through double petri dish assay. It inhibited both mycelium growth and conidia germination of B. cinerea, C. acutatum, and M. laxa, and reduced significantly by 53% and 18% respectively P. expansum. Three major VOCS: geosmin, phenethyl alcolhol (PEA) and an unknown substance were identified by GC-MS analysis. Consistent fumigation of fungal pathogens with PEA (1230 mg/mL), inhibited both conidia germination and mycelium growth of all pathogens, except conidia germination of P. expansum that was reduced by 90% with respect to control. While, the concentration of PEA produced naturally by LB8/99 was ineffective in controlling the pathogens and seemed to have a synergic or additive effect with the other VOCS. Investigations to study the biofumigant effect of LB8/99 on other commodities like seeds and seedlings are in progress.

Optimization of an innovative T6 heat treatment for the AlSi10Mg alloy processed by Laser-based Powder Bed Fusion: effect on microstructure, mechanical properties, and tribological behavior

Laser-based Powder Bed Fusion (L-PBF) technology is one of the most commonly used metal Additive Manufacturing (AM) techniques to produce highly customized and value-added parts. The AlSi10Mg alloy has received more attention in the L-PBF process due to its good printability, high strength/weight ratio, corrosion resistance, and relatively low cost. However, a deep understanding of the effect of heat treatments on this alloy's metastable microstructure is still required for developing tailored heat treatments for the L-PBF AlSi10Mg alloy to overcome the limits of the as-built condition. Several authors have already investigated the effects of conventional heat treatment on the microstructure and mechanical behavior of the L-PBF AlSi10Mg alloy but often overlooked the peculiarities of the starting supersatured and ultrafine microstructure induced by rapid solidification. For this reason, the effects of innovative T6 heat treatment (T6R) on the microstructure and mechanical behavior of the L-PBF AlSi10Mg alloy were assessed. The short solution soaking time (10 min) and the relatively low temperature (510 °C) reduced the typical porosity growth at high temperatures and led to a homogeneous distribution of fine globular Si particles in the Al matrix. In addition, it increased the amount of Mg and Si in the solid solution available for precipitation hardening during the aging step. The mechanical (at room temperature and 200 °C) and tribological properties of the T6R alloy were evaluated and compared with other solutions, especially with an optimized direct-aged alloy (T5 alloy). Results showed that the innovative T6R alloy exhibits the best mechanical trade-off between strength and ductility, the highest fatigue strength among the analyzed conditions, and interesting tribological behavior. Furthermore, the high-temperature mechanical performances of the heat-treated L-PBF AlSi10Mg alloy make it suitable for structural components operating in mild service conditions at 200 °C.