Componenti spaziali della rappresentazione cognitiva della grandezza del numero

The humans process the numbers in a similar way to animals. There are countless studies in which similar performance between animals and humans (adults and/or children) are reported. Three models have been developed to explain the cognitive mechanisms underlying the number processing. The triple-code model (Dehaene, 1992) posits an mental number line as preferred way to represent magnitude. The mental number line has three particular effects: the distance, the magnitude and the SNARC effects. The SNARC effect shows a spatial association between number and space representations. In other words, the small numbers are related to left space while large numbers are related to right space. Recently a vertical SNARC effect has been found (Ito & Hatta, 2004; Schwarz & Keus, 2004), reflecting a space-related bottom-to-up representation of numbers. The magnitude representations horizontally and vertically could influence the subject performance in explicit and implicit digit tasks. The goal of this research project aimed to investigate the spatial components of number representation using different experimental designs and tasks. The experiment 1 focused on horizontal and vertical number representations in a within- and between-subjects designs in a parity and magnitude comparative tasks, presenting positive or negative Arabic digits (1-9 without 5). The experiment 1A replied the SNARC and distance effects in both spatial arrangements. The experiment 1B showed an horizontal reversed SNARC effect in both tasks while a vertical reversed SNARC effect was found only in comparative task. In the experiment 1C two groups of subjects performed both tasks in two different instruction-responding hand assignments with positive numbers. The results did not show any significant differences between two assignments, even if the vertical number line seemed to be more flexible respect to horizontal one. On the whole the experiment 1 seemed to demonstrate a contextual (i.e. task set) influences of the nature of the SNARC effect. The experiment 2 focused on the effect of horizontal and vertical number representations on spatial biases in a paper-and-pencil bisecting tasks. In the experiment 2A the participants were requested to bisect physical and number (2 or 9) lines horizontally and vertically. The findings demonstrated that digit 9 strings tended to generate a more rightward bias comparing with digit 2 strings horizontally. However in vertical condition the digit 2 strings generated a more upperward bias respect to digit 9 strings, suggesting a top-to-bottom number line. In the experiment 2B the participants were asked to bisect lines flanked by numbers (i.e. 1 or 7) in four spatial arrangements: horizontal, vertical, right-diagonal and left-diagonal lines. Four number conditions were created according to congruent or incongruent number line representation: 1-1, 1-7, 7-1 and 7-7. The main results showed a more reliable rightward bias in horizontal congruent condition (1-7) respect to incongruent condition (7-1). Vertically the incongruent condition (1-7) determined a significant bias towards bottom side of line respect to congruent condition (7-1). The experiment 2 suggested a more rigid horizontal number line while in vertical condition the number representation could be more flexible. In the experiment 3 we adopted the materials of experiment 2B in order to find a number line effect on temporal (motor) performance. The participants were presented horizontal, vertical, rightdiagonal and left-diagonal lines flanked by the same digits (i.e. 1-1 or 7-7) or by different digits (i.e. 1-7 or 7-1). The digits were spatially congruent or incongruent with their respective hypothesized mental representations. Participants were instructed to touch the lines either close to the large digit, or close to the small digit, or to bisected the lines. Number processing influenced movement execution more than movement planning. Number congruency influenced spatial biases mostly along the horizontal but also along the vertical dimension. These results support a two-dimensional magnitude representation. Finally, the experiment 4 addressed the visuo-spatial manipulation of number representations for accessing and retrieval arithmetic facts. The participants were requested to perform a number-matching and an addition verification tasks. The findings showed an interference effect between sum-nodes and neutral-nodes only with an horizontal presentation of digit-cues, in number-matching tasks. In the addition verification task, the performance was similar for horizontal and vertical presentations of arithmetic problems. In conclusion the data seemed to show an automatic activation of horizontal number line also used to retrieval arithmetic facts. The horizontal number line seemed to be more rigid and the preferred way to order number from left-to-right. A possible explanation could be the left-to-right direction for reading and writing. The vertical number line seemed to be more flexible and more dependent from the tasks, reflecting perhaps several example in the environment representing numbers either from bottom-to-top or from top-to-bottom. However the bottom-to-top number line seemed to be activated by explicit task demands.

Reduced-order modelling, circuit-level design and SOI fabrication of microelectromechanical resonators

This thesis deals with two important research aspects concerning radio frequency (RF) microresonators and switches. First, a new approach for compact modeling and simulation of these devices is presented. Then, a combined process flow for their simultaneous fabrication on a SOI substrate is proposed. Compact models for microresonators and switches are extracted by applying mathematical model order reduction (MOR) to the devices finite element (FE) description in ANSYS c° . The behaviour of these devices includes forms of nonlinearities. However, an approximation in the creation of the FE model is introduced, which enables the use of linear model order reduction. Microresonators are modeled with the introduction of transducer elements, which allow for direct coupling of the electrical and mechanical domain. The coupled system element matrices are linearized around an operating point and reduced. The resulting macromodel is valid for small signal analysis around the bias point, such as harmonic pre-stressed analysis. This is extremely useful for characterizing the frequency response of resonators. Compact modelling of switches preserves the nonlinearity of the device behaviour. Nonlinear reduced order models are obtained by reducing the number of nonlinearities in the system and handling them as input to the system. In this way, the system can be reduced using linear MOR techniques and nonlinearities are introduced directly in the reduced order model. The reduction of the number of system nonlinearities implies the approximation of all distributed forces in the model with lumped forces. Both for microresonators and switches, a procedure for matrices extraction has been developed so that reduced order models include the effects of electrical and mechanical pre-stress. The extraction process is fast and can be done automatically from ANSYS binary files. The method has been applied for the simulation of several devices both at devices and circuit level. Simulation results have been compared with full model simulations, and, when available, experimental data. Reduced order models have proven to conserve the accuracy of finite element method and to give a good description of the overall device behaviour, despite the introduced approximations. In addition, simulation is very fast, both at device and circuit level. A combined process-flow for the integrated fabrication of microresonators and switches has been defined. For this purpose, two processes that are optimized for the independent fabrication of these devices are merged. The major advantage of this process is the possibility to create on-chip circuit blocks that include both microresonators and switches. An application is, for example, aswitched filter bank for wireless transceiver. The process for microresonators fabrication is characterized by the use of silicon on insulator (SOI) wafers and on a deep reactive ion etching (DRIE) step for the creation of the vibrating structures in single-crystal silicon and the use of a sacrificial oxide layer for the definition of resonator to electrode distance. The fabrication of switches is characterized by the use of two different conductive layers for the definition of the actuation electrodes and by the use of a photoresist as a sacrificial layer for the creation of the suspended structure. Both processes have a gold electroplating step, for the creation of the resonators electrodes, transmission lines and suspended structures. The combined process flow is designed such that it conserves the basic properties of the original processes. Neither the performance of the resonators nor the performance of the switches results affected by the simultaneous fabrication. Moreover, common fabrication steps are shared, which allows for cheaper and faster fabrication.