Toxoplasma gondii in animals and the environment

Toxoplasma gondii is an obligate intracellular parasite capable of infecting virtually all warm-blooded species, including humans, but cats are the only definitive hosts. Humans or animals acquire T. gondii infection by ingesting food or water contaminated with sporulated oocysts or by ingesting tissue cysts containing bradyzoites. Toxoplasmosis has the highest human incidence among zoonotic parasitic diseases, but it is still considered an underreported zoonosis. The importance of T. gondii primary infection in livestock is related to the ability of the parasite to produce tissue cysts in infected animals, which may represent important sources of infection for humans. Consumption of undercooked mutton and pork are considered important sources of human Toxoplasma gondii. The first aim of this thesis was to develop a rapid and sensitive in- house indirect ELISA for the detection of antibodies against T. gondii in sheep sera. ROC-curve analysis showed high discriminatory power (AUC=0.999) and high sensitivity (99.4%) and specificity (99.8%) of the method. The ELISA was used to test a batch of sheep sera (375) collected in the Forli-Cesena district. The overall prevalence was estimated at 41.9% demonstrating that T. gondii infection is widely distributed in sheep reared in Forli-Cesena district. Since the epidemiological impact of waterborne transmission route of T.gondii to humans is now thought to be more significant than previously believed, the second aim of the thesis was to evaluate PCR based methods for detecting T. gondii DNA in raw and finished drinking water samples collected in Scotland. Samples were tested using a quantitative PCR on 529 bp repetitive elements. Only one raw water sample (0.3%), out of the 358 examined, tested T. gondii positive demonstrating that there is no evidence that tap water is a source of Toxoplasma infection in Scotland.

The challenges and the limitations in Life Cycle Impact Assessment for metal oxide nanoparticles, a case study on nano- TiO2

Life Cycle Assessment (LCA) is a chain-oriented tool to evaluate the environment performance of products focussing on the entire life cycle of these products: from the extraction of resources, via manufacturing and use, to the final processing of the disposed products. Through all these stages consumption of resources and pollutant releases to air, water, soil are identified and quantified in Life Cycle Inventory (LCI) analysis. Subsequently to the LCI phase follows the Life Cycle Impact Assessment (LCIA) phase; that has the purpose to convert resource consumptions and pollutant releases in environmental impacts. The LCIA aims to model and to evaluate environmental issues, called impact categories. Several reports emphasises the importance of LCA in the field of ENMs. The ENMs offer enormous potential for the development of new products and application. There are however unanswered questions about the impacts of ENMs on human health and the environment. In the last decade the increasing production, use and consumption of nanoproducts, with a consequent release into the environment, has accentuated the obligation to ensure that potential risks are adequately understood to protect both human health and environment. Due to its holistic and comprehensive assessment, LCA is an essential tool evaluate, understand and manage the environmental and health effects of nanotechnology. The evaluation of health and environmental impacts of nanotechnologies, throughout the whole of their life-cycle by using LCA methodology. This is due to the lack of knowledge in relation to risk assessment. In fact, to date, the knowledge on human and environmental exposure to nanomaterials, such ENPs is limited. This bottleneck is reflected into LCA where characterisation models and consequently characterisation factors for ENPs are missed. The PhD project aims to assess limitations and challenges of the freshwater aquatic ecotoxicity potential evaluation in LCIA phase for ENPs and in particular nanoparticles as n-TiO2.

Welfare provision in Sweden and the dominant position of the Sap

There have been almost fifty years since Harry Eckstein' s classic monograph, A Theory of Stable Democracy (Princeton, 1961), where he sketched out the basic tenets of the “congruence theory”, which was to become one of the most important and innovative contributions to understanding democratic rule. His next work, Division and Cohesion in Democracy, (Princeton University Press: 1966) is designed to serve as a plausibility probe for this 'theory' (ftn.) and is a case study of a Northern democratic system, Norway. What is more, this line of his work best exemplifies the contribution Eckstein brought to the methodology of comparative politics through his seminal article, “ “Case Study and Theory in Political Science” ” (in Greenstein and Polsby, eds., Handbook of Political Science, 1975), on the importance of the case study as an approach to empirical theory. This article demonstrates the special utility of “crucial case studies” in testing theory, thereby undermining the accepted wisdom in comparative research that the larger the number of cases the better. Although not along the same lines, but shifting the case study unit of research, I intend to take up here the challenge and build upon an equally unique political system, the Swedish one. Bearing in mind the peculiarities of the Swedish political system, my unit of analysis is going to be further restricted to the Swedish Social Democratic Party, the Svenska Arbetare Partiet. However, my research stays within the methodological framework of the case study theory inasmuch as it focuses on a single political system and party. The Swedish SAP endurance in government office and its electoral success throughout half a century (ftn. As of the 1991 election, there were about 56 years - more than half century - of interrupted social democratic "reign" in Sweden.) are undeniably a performance no other Social Democrat party has yet achieved in democratic conditions. Therefore, it is legitimate to inquire about the exceptionality of this unique political power combination. Which were the different components of this dominance power position, which made possible for SAP's governmental office stamina? I will argue here that it was the end-product of a combination of multifarious factors such as a key position in the party system, strong party leadership and organization, a carefully designed strategy regarding class politics and welfare policy. My research is divided into three main parts, the historical incursion, the 'welfare' part and the 'environment' part. The first part is a historical account of the main political events and issues, which are relevant for my case study. Chapter 2 is devoted to the historical events unfolding in the 1920-1960 period: the Saltsjoebaden Agreement, the series of workers' strikes in the 1920s and SAP's inception. It exposes SAP's ascent to power in the mid 1930s and the party's ensuing strategies for winning and keeping political office, that is its economic program and key economic goals. The following chapter - chapter 3 - explores the next period, i.e. the period from 1960s to 1990s and covers the party's troubled political times, its peak and the beginnings of the decline. The 1960s are relevant for SAP's planning of a long term economic strategy - the Rehn Meidner model, a new way of macroeconomic steering, based on the Keynesian model, but adapted to the new economic realities of welfare capitalist societies. The second and third parts of this study develop several hypotheses related to SAP's 'dominant position' (endurance in politics and in office) and test them afterwards. Mainly, the twin issues of economics and environment are raised and their political relevance for the party analyzed. On one hand, globalization and its spillover effects over the Swedish welfare system are important causal factors in explaining the transformative social-economic challenges the party had to put up with. On the other hand, Europeanization and environmental change influenced to a great deal SAP's foreign policy choices and its domestic electoral strategies. The implications of globalization on the Swedish welfare system will make the subject of two chapters - chapters four and five, respectively, whereupon the Europeanization consequences will be treated at length in the third part of this work - chapters six and seven, respectively. Apparently, at first sight, the link between foreign policy and electoral strategy is difficult to prove and uncanny, in the least. However, in the SAP's case there is a bulk of literature and public opinion statistical data able to show that governmental domestic policy and party politics are in a tight dependence to foreign policy decisions and sovereignty issues. Again, these country characteristics and peculiar causal relationships are outlined in the first chapters and explained in the second and third parts. The sixth chapter explores the presupposed relationship between Europeanization and environmental policy, on one hand, and SAP's environmental policy formulation and simultaneous agenda-setting at the international level, on the other hand. This chapter describes Swedish leadership in environmental policy formulation on two simultaneous fronts and across two different time spans. The last chapter, chapter eight - while trying to develop a conclusion, explores the alternative theories plausible in explaining the outlined hypotheses and points out the reasons why these theories do not fit as valid alternative explanation to my systemic corporatism thesis as the main causal factor determining SAP's 'dominant position'. Among the alternative theories, I would consider Traedgaardh L. and Bo Rothstein's historical exceptionalism thesis and the public opinion thesis, which alone are not able to explain the half century social democratic endurance in government in the Swedish case.

Some issues concerning the dynamic response and damage of composite laminates subjected to low velocity impact

Abstract. This thesis presents a discussion on a few specific topics regarding the low velocity impact behaviour of laminated composites. These topics were chosen because of their significance as well as the relatively limited attention received so far by the scientific community. The first issue considered is the comparison between the effects induced by a low velocity impact and by a quasi-static indentation experimental test. An analysis of both test conditions is presented, based on the results of experiments carried out on carbon fibre laminates and on numerical computations by a finite element model. It is shown that both quasi-static and dynamic tests led to qualitatively similar failure patterns; three characteristic contact force thresholds, corresponding to the main steps of damage progression, were identified and found to be equal for impact and indentation. On the other hand, an equal energy absorption resulted in a larger delaminated area in quasi-static than in dynamic tests, while the maximum displacement of the impactor (or indentor) was higher in the case of impact, suggesting a probably more severe fibre damage than in indentation. Secondly, the effect of different specimen dimensions and boundary conditions on its impact response was examined. Experimental testing showed that the relationships of delaminated area with two significant impact parameters, the absorbed energy and the maximum contact force, did not depend on the in-plane dimensions and on the support condition of the coupons. The possibility of predicting, by means of a simplified numerical computation, the occurrence of delaminations during a specific impact event is also discussed. A study about the compressive behaviour of impact damaged laminates is also presented. Unlike most of the contributions available about this subject, the results of compression after impact tests on thin laminates are described in which the global specimen buckling was not prevented. Two different quasi-isotropic stacking sequences, as well as two specimen geometries, were considered. It is shown that in the case of rectangular coupons the lay-up can significantly affect the damage induced by impact. Different buckling shapes were observed in laminates with different stacking sequences, in agreement with the results of numerical analysis. In addition, the experiments showed that impact damage can alter the buckling mode of the laminates in certain situations, whereas it did not affect the compressive strength in every case, depending on the buckling shape. Some considerations about the significance of the test method employed are also proposed. Finally, a comprehensive study is presented regarding the influence of pre-existing in-plane loads on the impact response of laminates. Impact events in several conditions, including both tensile and compressive preloads, both uniaxial and biaxial, were analysed by means of numerical finite element simulations; the case of laminates impacted in postbuckling conditions was also considered. The study focused on how the effect of preload varies with the span-to-thickness ratio of the specimen, which was found to be a key parameter. It is shown that a tensile preload has the strongest effect on the peak stresses at low span-to-thickness ratios, leading to a reduction of the minimum impact energy required to initiate damage, whereas this effect tends to disappear as the span-to-thickness ratio increases. On the other hand, a compression preload exhibits the most detrimental effects at medium span-to-thickness ratios, at which the laminate compressive strength and the critical instability load are close to each other, while the influence of preload can be negligible for thin plates or even beneficial for very thick plates. The possibility to obtain a better explanation of the experimental results described in the literature, in view of the present findings, is highlighted. Throughout the thesis the capabilities and limitations of the finite element model, which was implemented in an in-house program, are discussed. The program did not include any damage model of the material. It is shown that, although this kind of analysis can yield accurate results as long as damage has little effect on the overall mechanical properties of a laminate, it can be helpful in explaining some phenomena and also in distinguishing between what can be modelled without taking into account the material degradation and what requires an appropriate simulation of damage. Sommario. Questa tesi presenta una discussione su alcune tematiche specifiche riguardanti il comportamento dei compositi laminati soggetti ad impatto a bassa velocità. Tali tematiche sono state scelte per la loro importanza, oltre che per l’attenzione relativamente limitata ricevuta finora dalla comunità scientifica. La prima delle problematiche considerate è il confronto fra gli effetti prodotti da una prova sperimentale di impatto a bassa velocità e da una prova di indentazione quasi statica. Viene presentata un’analisi di entrambe le condizioni di prova, basata sui risultati di esperimenti condotti su laminati in fibra di carbonio e su calcoli numerici svolti con un modello ad elementi finiti. È mostrato che sia le prove quasi statiche sia quelle dinamiche portano a un danneggiamento con caratteristiche qualitativamente simili; tre valori di soglia caratteristici della forza di contatto, corrispondenti alle fasi principali di progressione del danno, sono stati individuati e stimati uguali per impatto e indentazione. D’altro canto lo stesso assorbimento di energia ha portato ad un’area delaminata maggiore nelle prove statiche rispetto a quelle dinamiche, mentre il massimo spostamento dell’impattatore (o indentatore) è risultato maggiore nel caso dell’impatto, indicando la probabilità di un danneggiamento delle fibre più severo rispetto al caso dell’indentazione. In secondo luogo è stato esaminato l’effetto di diverse dimensioni del provino e diverse condizioni al contorno sulla sua risposta all’impatto. Le prove sperimentali hanno mostrato che le relazioni fra l’area delaminata e due parametri di impatto significativi, l’energia assorbita e la massima forza di contatto, non dipendono dalle dimensioni nel piano dei provini e dalle loro condizioni di supporto. Viene anche discussa la possibilità di prevedere, per mezzo di un calcolo numerico semplificato, il verificarsi di delaminazioni durante un determinato caso di impatto. È presentato anche uno studio sul comportamento a compressione di laminati danneggiati da impatto. Diversamente della maggior parte della letteratura disponibile su questo argomento, vengono qui descritti i risultati di prove di compressione dopo impatto su laminati sottili durante le quali l’instabilità elastica globale dei provini non è stata impedita. Sono state considerate due differenti sequenze di laminazione quasi isotrope, oltre a due geometrie per i provini. Viene mostrato come nel caso di provini rettangolari la sequenza di laminazione possa influenzare sensibilmente il danno prodotto dall’impatto. Due diversi tipi di deformate in condizioni di instabilità sono stati osservati per laminati con diversa laminazione, in accordo con i risultati dell’analisi numerica. Gli esperimenti hanno mostrato inoltre che in certe situazioni il danno da impatto può alterare la deformata che il laminato assume in seguito ad instabilità; d’altra parte tale danno non ha sempre influenzato la resistenza a compressione, a seconda della deformata. Vengono proposte anche alcune considerazioni sulla significatività del metodo di prova utilizzato. Infine viene presentato uno studio esaustivo riguardo all’influenza di carichi membranali preesistenti sulla risposta all’impatto dei laminati. Sono stati analizzati con simulazioni numeriche ad elementi finiti casi di impatto in diverse condizioni di precarico, sia di trazione sia di compressione, sia monoassiali sia biassiali; è stato preso in considerazione anche il caso di laminati impattati in condizioni di postbuckling. Lo studio si è concentrato in particolare sulla dipendenza degli effetti del precarico dal rapporto larghezza-spessore del provino, che si è rivelato un parametro fondamentale. Viene illustrato che un precarico di trazione ha l’effetto più marcato sulle massime tensioni per bassi rapporti larghezza-spessore, portando ad una riduzione della minima energia di impatto necessaria per innescare il danneggiamento, mentre questo effetto tende a scomparire all’aumentare di tale rapporto. Il precarico di compressione evidenzia invece gli effetti più deleteri a rapporti larghezza-spessore intermedi, ai quali la resistenza a compressione del laminato e il suo carico critico di instabilità sono paragonabili, mentre l’influenza del precarico può essere trascurabile per piastre sottili o addirittura benefica per piastre molto spesse. Viene evidenziata la possibilità di trovare una spiegazione più soddisfacente dei risultati sperimentali riportati in letteratura, alla luce del presente contributo. Nel corso della tesi vengono anche discussi le potenzialità ed i limiti del modello ad elementi finiti utilizzato, che è stato implementato in un programma scritto in proprio. Il programma non comprende alcuna modellazione del danneggiamento del materiale. Viene però spiegato come, nonostante questo tipo di analisi possa portare a risultati accurati soltanto finché il danno ha scarsi effetti sulle proprietà meccaniche d’insieme del laminato, esso possa essere utile per spiegare alcuni fenomeni, oltre che per distinguere fra ciò che si può riprodurre senza tenere conto del degrado del materiale e ciò che invece richiede una simulazione adeguata del danneggiamento.

Antiepileptic drugs and pregnancy. Population based pharmaco-epidemiological study on prescription patterns, pregnancy outcome and foetal health

Aims of the study: To assess the prevalence of Antiepileptic Drug (AED) exposure in pregnant women with or without epilepsy and the comparative risk of terminations of pregnancy (TOPs), spontaneous abortions, stillbirth, major congenital malformations (MCMs) and foetal growth retardation (FGR) following intrauterine AED exposure in the Emilia Romagna region (RER), Northern Italy (4 million inhabitants). Methods: Data were obtained from official regional registries: Certificate of Delivery Assistance, Hospital Discharge Card, reimbursed prescription databases and Registry of Congenital Malformations. We identified all the deliveries, hospitalized abortions and MCMs occurred between January 2009 and December 2011. Results: We identified 145,243 pregnancies: 111,284 deliveries (112,845 live births and 279 stillbirths), 16408 spontaneous abortions and 17551 TOPs. Six hundred and eleven pregnancies (0.42% 95% Cl: 0.39-0.46) were exposed to AEDs. Twenty-one per cent of pregnancies ended in TOP in the AED group vs 12% in the non-exposed (OR:2.24; CI 1.41-3.56). The rate of spontaneous abortions and stillbirth was comparable in the two groups. Three hundred fifty-three babies (0.31%, 95% CI: 0.28-0.35) were exposed to AEDs during the first trimester. The rate of MCMs was 2.3% in the AED group (2.2% in babies exposed to monotherapy and 3.1% in babies exposed to polytherapy) vs 2.0% in the non-exposed. The risk of FGR was 12.7 % in the exposed group compared to 10% in the non-exposed. Discussion and Conclusion: The prevalence of AED exposure in pregnancy in the RER was 0.42%. The rate of MCMs in children exposed to AEDs in utero was almost superimposable to the one of the non-exposed, however polytherapy carried a slightly increased risk . The rate of TOPs was significantly higher in the exposed women. Further studies are needed to clarify whether this high rate reflects a higher rate of MCMs detected prenatally or other more elusive reasons.