Dynamic identification of structures: experimental assessment of modal parameteres through methods in frequency domain, in time-frequency domain and model updating

Among the experimental methods commonly used to define the behaviour of a full scale system, dynamic tests are the most complete and efficient procedures. A dynamic test is an experimental process, which would define a set of characteristic parameters of the dynamic behaviour of the system, such as natural frequencies of the structure, mode shapes and the corresponding modal damping values associated. An assessment of these modal characteristics can be used both to verify the theoretical assumptions of the project, to monitor the performance of the structural system during its operational use. The thesis is structured in the following chapters: The first introductive chapter recalls some basic notions of dynamics of structure, focusing the discussion on the problem of systems with multiply degrees of freedom (MDOF), which can represent a generic real system under study, when it is excited with harmonic force or in free vibration. The second chapter is entirely centred on to the problem of dynamic identification process of a structure, if it is subjected to an experimental test in forced vibrations. It first describes the construction of FRF through classical FFT of the recorded signal. A different method, also in the frequency domain, is subsequently introduced; it allows accurately to compute the FRF using the geometric characteristics of the ellipse that represents the direct input-output comparison. The two methods are compared and then the attention is focused on some advantages of the proposed methodology. The third chapter focuses on the study of real structures when they are subjected to experimental test, where the force is not known, like in an ambient or impact test. In this analysis we decided to use the CWT, which allows a simultaneous investigation in the time and frequency domain of a generic signal x(t). The CWT is first introduced to process free oscillations, with excellent results both in terms of frequencies, dampings and vibration modes. The application in the case of ambient vibrations defines accurate modal parameters of the system, although on the damping some important observations should be made. The fourth chapter is still on the problem of post processing data acquired after a vibration test, but this time through the application of discrete wavelet transform (DWT). In the first part the results obtained by the DWT are compared with those obtained by the application of CWT. Particular attention is given to the use of DWT as a tool for filtering the recorded signal, in fact in case of ambient vibrations the signals are often affected by the presence of a significant level of noise. The fifth chapter focuses on another important aspect of the identification process: the model updating. In this chapter, starting from the modal parameters obtained from some environmental vibration tests, performed by the University of Porto in 2008 and the University of Sheffild on the Humber Bridge in England, a FE model of the bridge is defined, in order to define what type of model is able to capture more accurately the real dynamic behaviour of the bridge. The sixth chapter outlines the necessary conclusions of the presented research. They concern the application of a method in the frequency domain in order to evaluate the modal parameters of a structure and its advantages, the advantages in applying a procedure based on the use of wavelet transforms in the process of identification in tests with unknown input and finally the problem of 3D modeling of systems with many degrees of freedom and with different types of uncertainty.

Mixed Mode Fracture Behaviour of Piezoelectric Materials

Piezoelectrics present an interactive electromechanical behaviour that, especially in recent years, has generated much interest since it renders these materials adapt for use in a variety of electronic and industrial applications like sensors, actuators, transducers, smart structures. Both mechanical and electric loads are generally applied on these devices and can cause high concentrations of stress, particularly in proximity of defects or inhomogeneities, such as flaws, cavities or included particles. A thorough understanding of their fracture behaviour is crucial in order to improve their performances and avoid unexpected failures. Therefore, a considerable number of research works have addressed this topic in the last decades. Most of the theoretical studies on this subject find their analytical background in the complex variable formulation of plane anisotropic elasticity. This theoretical approach bases its main origins in the pioneering works of Muskelishvili and Lekhnitskii who obtained the solution of the elastic problem in terms of independent analytic functions of complex variables. In the present work, the expressions of stresses and elastic and electric displacements are obtained as functions of complex potentials through an analytical formulation which is the application to the piezoelectric static case of an approach introduced for orthotropic materials to solve elastodynamics problems. This method can be considered an alternative to other formalisms currently used, like the Stroh’s formalism. The equilibrium equations are reduced to a first order system involving a six-dimensional vector field. After that, a similarity transformation is induced to reach three independent Cauchy-Riemann systems, so justifying the introduction of the complex variable notation. Closed form expressions of near tip stress and displacement fields are therefore obtained. In the theoretical study of cracked piezoelectric bodies, the issue of assigning consistent electric boundary conditions on the crack faces is of central importance and has been addressed by many researchers. Three different boundary conditions are commonly accepted in literature: the permeable, the impermeable and the semipermeable (“exact”) crack model. This thesis takes into considerations all the three models, comparing the results obtained and analysing the effects of the boundary condition choice on the solution. The influence of load biaxiality and of the application of a remote electric field has been studied, pointing out that both can affect to a various extent the stress fields and the angle of initial crack extension, especially when non-singular terms are retained in the expressions of the electro-elastic solution. Furthermore, two different fracture criteria are applied to the piezoelectric case, and their outcomes are compared and discussed. The work is organized as follows: Chapter 1 briefly introduces the fundamental concepts of Fracture Mechanics. Chapter 2 describes plane elasticity formalisms for an anisotropic continuum (Eshelby-Read-Shockley and Stroh) and introduces for the simplified orthotropic case the alternative formalism we want to propose. Chapter 3 outlines the Linear Theory of Piezoelectricity, its basic relations and electro-elastic equations. Chapter 4 introduces the proposed method for obtaining the expressions of stresses and elastic and electric displacements, given as functions of complex potentials. The solution is obtained in close form and non-singular terms are retained as well. Chapter 5 presents several numerical applications aimed at estimating the effect of load biaxiality, electric field, considered permittivity of the crack. Through the application of fracture criteria the influence of the above listed conditions on the response of the system and in particular on the direction of crack branching is thoroughly discussed.

Evaluation of the effects of insertion of viscous dampers in Moment Resisting Frames

This research work faces the problem of insertion of viscous dampers into Moment Resisiting Frames (MRF) for maximum efficiency in mitigation of the seismic effects. The work would lead to a precise design indication. The fundamental result of the thesis consists in showing that, even for moment-resisting structures, you can design a system of added viscous dampers able to achieve target levels of performances. Ie given the reduction factor in the seismic response, discover the characteristics of the viscous dampers which allow to achieve it.

Calcolo della posizione di reti di stazioni permanenti

Con il trascorrere del tempo, le reti di stazioni permanenti GNSS (Global Navigation Satellite System) divengono sempre più un valido supporto alle tecniche di rilevamento satellitare. Esse sono al tempo stesso un’efficace materializzazione del sistema di riferimento e un utile ausilio ad applicazioni di rilevamento topografico e di monitoraggio per il controllo di deformazioni. Alle ormai classiche applicazioni statiche in post-processamento, si affiancano le misure in tempo reale sempre più utilizzate e richieste dall’utenza professionale. In tutti i casi risulta molto importante la determinazione di coordinate precise per le stazioni permanenti, al punto che si è deciso di effettuarla tramite differenti ambienti di calcolo. Sono stati confrontati il Bernese, il Gamit (che condividono l’approccio differenziato) e il Gipsy (che utilizza l’approccio indifferenziato). L’uso di tre software ha reso indispensabile l’individuazione di una strategia di calcolo comune in grado di garantire che, i dati ancillari e i parametri fisici adottati, non costituiscano fonte di diversificazione tra le soluzioni ottenute. L’analisi di reti di dimensioni nazionali oppure di reti locali per lunghi intervalli di tempo, comporta il processamento di migliaia se non decine di migliaia di file; a ciò si aggiunge che, talora a causa di banali errori, oppure al fine di elaborare test scientifici, spesso risulta necessario reiterare le elaborazioni. Molte risorse sono quindi state investite nella messa a punto di procedure automatiche finalizzate, da un lato alla preparazione degli archivi e dall’altro all’analisi dei risultati e al loro confronto qualora si sia in possesso di più soluzioni. Dette procedure sono state sviluppate elaborando i dataset più significativi messi a disposizione del DISTART (Dipartimento di Ingegneria delle Strutture, dei Trasporti, delle Acque, del Rilevamento del Territorio - Università di Bologna). E’ stato così possibile, al tempo stesso, calcolare la posizione delle stazioni permanenti di alcune importanti reti locali e nazionali e confrontare taluni fra i più importanti codici scientifici che assolvono a tale funzione. Per quanto attiene il confronto fra i diversi software si è verificato che: • le soluzioni ottenute dal Bernese e da Gamit (i due software differenziati) sono sempre in perfetto accordo; • le soluzioni Gipsy (che utilizza il metodo indifferenziato) risultano, quasi sempre, leggermente più disperse rispetto a quelle degli altri software e mostrano talvolta delle apprezzabili differenze numeriche rispetto alle altre soluzioni, soprattutto per quanto attiene la coordinata Est; le differenze sono però contenute in pochi millimetri e le rette che descrivono i trend sono comunque praticamente parallele a quelle degli altri due codici; • il citato bias in Est tra Gipsy e le soluzioni differenziate, è più evidente in presenza di determinate combinazioni Antenna/Radome e sembra essere legato all’uso delle calibrazioni assolute da parte dei diversi software. E’ necessario altresì considerare che Gipsy è sensibilmente più veloce dei codici differenziati e soprattutto che, con la procedura indifferenziata, il file di ciascuna stazione di ciascun giorno, viene elaborato indipendentemente dagli altri, con evidente maggior elasticità di gestione: se si individua un errore strumentale su di una singola stazione o se si decide di aggiungere o togliere una stazione dalla rete, non risulta necessario il ricalcolo dell’intera rete. Insieme alle altre reti è stato possibile analizzare la Rete Dinamica Nazionale (RDN), non solo i 28 giorni che hanno dato luogo alla sua prima definizione, bensì anche ulteriori quattro intervalli temporali di 28 giorni, intercalati di sei mesi e che coprono quindi un intervallo temporale complessivo pari a due anni. Si è così potuto verificare che la RDN può essere utilizzata per l’inserimento in ITRF05 (International Terrestrial Reference Frame) di una qualsiasi rete regionale italiana nonostante l’intervallo temporale ancora limitato. Da un lato sono state stimate le velocità ITRF (puramente indicative e non ufficiali) delle stazioni RDN e, dall’altro, è stata effettuata una prova di inquadramento di una rete regionale in ITRF, tramite RDN, e si è verificato che non si hanno differenze apprezzabili rispetto all’inquadramento in ITRF, tramite un congruo numero di stazioni IGS/EUREF (International GNSS Service / European REference Frame, SubCommission for Europe dello International Association of Geodesy).