Tools and methods for the quality assurance of force platforms in human movement analysis

The human movement analysis (HMA) aims to measure the abilities of a subject to stand or to walk. In the field of HMA, tests are daily performed in research laboratories, hospitals and clinics, aiming to diagnose a disease, distinguish between disease entities, monitor the progress of a treatment and predict the outcome of an intervention [Brand and Crowninshield, 1981; Brand, 1987; Baker, 2006]. To achieve these purposes, clinicians and researchers use measurement devices, like force platforms, stereophotogrammetric systems, accelerometers, baropodometric insoles, etc. This thesis focus on the force platform (FP) and in particular on the quality assessment of the FP data. The principal objective of our work was the design and the experimental validation of a portable system for the in situ calibration of FPs. The thesis is structured as follows: Chapter 1. Description of the physical principles used for the functioning of a FP: how these principles are used to create force transducers, such as strain gauges and piezoelectrics transducers. Then, description of the two category of FPs, three- and six-component, the signals acquisition (hardware structure), and the signals calibration. Finally, a brief description of the use of FPs in HMA, for balance or gait analysis. Chapter 2. Description of the inverse dynamics, the most common method used in the field of HMA. This method uses the signals measured by a FP to estimate kinetic quantities, such as joint forces and moments. The measures of these variables can not be taken directly, unless very invasive techniques; consequently these variables can only be estimated using indirect techniques, as the inverse dynamics. Finally, a brief description of the sources of error, present in the gait analysis. Chapter 3. State of the art in the FP calibration. The selected literature is divided in sections, each section describes: systems for the periodic control of the FP accuracy; systems for the error reduction in the FP signals; systems and procedures for the construction of a FP. In particular is detailed described a calibration system designed by our group, based on the theoretical method proposed by ?. This system was the “starting point” for the new system presented in this thesis. Chapter 4. Description of the new system, divided in its parts: 1) the algorithm; 2) the device; and 3) the calibration procedure, for the correct performing of the calibration process. The algorithm characteristics were optimized by a simulation approach, the results are here presented. In addiction, the different versions of the device are described. Chapter 5. Experimental validation of the new system, achieved by testing it on 4 commercial FPs. The effectiveness of the calibration was verified by measuring, before and after calibration, the accuracy of the FPs in measuring the center of pressure of an applied force. The new system can estimate local and global calibration matrices; by local and global calibration matrices, the non–linearity of the FPs was quantified and locally compensated. Further, a non–linear calibration is proposed. This calibration compensates the non– linear effect in the FP functioning, due to the bending of its upper plate. The experimental results are presented. Chapter 6. Influence of the FP calibration on the estimation of kinetic quantities, with the inverse dynamics approach. Chapter 7. The conclusions of this thesis are presented: need of a calibration of FPs and consequential enhancement in the kinetic data quality. Appendix: Calibration of the LC used in the presented system. Different calibration set–up of a 3D force transducer are presented, and is proposed the optimal set–up, with particular attention to the compensation of non–linearities. The optimal set–up is verified by experimental results.

Computational analyses on the structure-function relation in ion channels

Ion channels are protein molecules, embedded in the lipid bilayer of the cell membranes. They act as powerful sensing elements switching chemicalphysical stimuli into ion-fluxes. At a glance, ion channels are water-filled pores, which can open and close in response to different stimuli (gating), and one once open select the permeating ion species (selectivity). They play a crucial role in several physiological functions, like nerve transmission, muscular contraction, and secretion. Besides, ion channels can be used in technological applications for different purpose (sensing of organic molecules, DNA sequencing). As a result, there is remarkable interest in understanding the molecular determinants of the channel functioning. Nowadays, both the functional and the structural characteristics of ion channels can be experimentally solved. The purpose of this thesis was to investigate the structure-function relation in ion channels, by computational techniques. Most of the analyses focused on the mechanisms of ion conduction, and the numerical methodologies to compute the channel conductance. The standard techniques for atomistic simulation of complex molecular systems (Molecular Dynamics) cannot be routinely used to calculate ion fluxes in membrane channels, because of the high computational resources needed. The main step forward of the PhD research activity was the development of a computational algorithm for the calculation of ion fluxes in protein channels. The algorithm - based on the electrodiffusion theory - is computational inexpensive, and was used for an extensive analysis on the molecular determinants of the channel conductance. The first record of ion-fluxes through a single protein channel dates back to 1976, and since then measuring the single channel conductance has become a standard experimental procedure. Chapter 1 introduces ion channels, and the experimental techniques used to measure the channel currents. The abundance of functional data (channel currents) does not match with an equal abundance of structural data. The bacterial potassium channel KcsA was the first selective ion channels to be experimentally solved (1998), and after KcsA the structures of four different potassium channels were revealed. These experimental data inspired a new era in ion channel modeling. Once the atomic structures of channels are known, it is possible to define mathematical models based on physical descriptions of the molecular systems. These physically based models can provide an atomic description of ion channel functioning, and predict the effect of structural changes. Chapter 2 introduces the computation methods used throughout the thesis to model ion channels functioning at the atomic level. In Chapter 3 and Chapter 4 the ion conduction through potassium channels is analyzed, by an approach based on the Poisson-Nernst-Planck electrodiffusion theory. In the electrodiffusion theory ion conduction is modeled by the drift-diffusion equations, thus describing the ion distributions by continuum functions. The numerical solver of the Poisson- Nernst-Planck equations was tested in the KcsA potassium channel (Chapter 3), and then used to analyze how the atomic structure of the intracellular vestibule of potassium channels affects the conductance (Chapter 4). As a major result, a correlation between the channel conductance and the potassium concentration in the intracellular vestibule emerged. The atomic structure of the channel modulates the potassium concentration in the vestibule, thus its conductance. This mechanism explains the phenotype of the BK potassium channels, a sub-family of potassium channels with high single channel conductance. The functional role of the intracellular vestibule is also the subject of Chapter 5, where the affinity of the potassium channels hEag1 (involved in tumour-cell proliferation) and hErg (important in the cardiac cycle) for several pharmaceutical drugs was compared. Both experimental measurements and molecular modeling were used in order to identify differences in the blocking mechanism of the two channels, which could be exploited in the synthesis of selective blockers. The experimental data pointed out the different role of residue mutations in the blockage of hEag1 and hErg, and the molecular modeling provided a possible explanation based on different binding sites in the intracellular vestibule. Modeling ion channels at the molecular levels relates the functioning of a channel to its atomic structure (Chapters 3-5), and can also be useful to predict the structure of ion channels (Chapter 6-7). In Chapter 6 the structure of the KcsA potassium channel depleted from potassium ions is analyzed by molecular dynamics simulations. Recently, a surprisingly high osmotic permeability of the KcsA channel was experimentally measured. All the available crystallographic structure of KcsA refers to a channel occupied by potassium ions. To conduct water molecules potassium ions must be expelled from KcsA. The structure of the potassium-depleted KcsA channel and the mechanism of water permeation are still unknown, and have been investigated by numerical simulations. Molecular dynamics of KcsA identified a possible atomic structure of the potassium-depleted KcsA channel, and a mechanism for water permeation. The depletion from potassium ions is an extreme situation for potassium channels, unlikely in physiological conditions. However, the simulation of such an extreme condition could help to identify the structural conformations, so the functional states, accessible to potassium ion channels. The last chapter of the thesis deals with the atomic structure of the !- Hemolysin channel. !-Hemolysin is the major determinant of the Staphylococcus Aureus toxicity, and is also the prototype channel for a possible usage in technological applications. The atomic structure of !- Hemolysin was revealed by X-Ray crystallography, but several experimental evidences suggest the presence of an alternative atomic structure. This alternative structure was predicted, combining experimental measurements of single channel currents and numerical simulations. This thesis is organized in two parts, in the first part an overview on ion channels and on the numerical methods adopted throughout the thesis is provided, while the second part describes the research projects tackled in the course of the PhD programme. The aim of the research activity was to relate the functional characteristics of ion channels to their atomic structure. In presenting the different research projects, the role of numerical simulations to analyze the structure-function relation in ion channels is highlighted.

Strumenti e metodi per lo sviluppo prodotto di lenti oftalmiche

The recent introduction of free form NC machining in the ophthalmic field involved a full review of the former product development process both from the design and the manufacturing viewpoint. Aim of the present work is to investigate and to set up innovative methods and tools supporting the product development, particularly for lenses characterized by free form geometry, as e.g. progressive lenses. In the design stage, the research addressed geometric modeling of complex lens shapes and relevant analysis tools for the optical-geometrical characterization of the produced models. In the manufacturing stage, the main interest was focused on the set-up of the fabrication process, particularly on the NC machining process for which an integration CADCAM software was developed for the generation and the simulation of the machining cycle. The methodologies and tools made available by the present work are currently used in the development of new complex geometry product typologies as, e.g. progressive lenses.

Simulatore di interfaccia uomo-macchina per i controllo di UAV

Recent statistics have demonstrated that two of the most important causes of failures of the UAVs (Uninhabited Aerial Vehicle) missions are related to the low level of decisional autonomy of vehicles and to the man machine interface. Therefore, a relevant issue is to design a display/controls architecture which allows the efficient interaction between the operator and the remote vehicle and to develop a level of automation which allows the vehicle the decision about change in mission. The research presented in this paper focuses on a modular man-machine interface simulator for the UAV control, which simulates UAV missions, developed to experiment solution to this problem. The main components of the simulator are an advanced interface and a block defined automation, which comprehend an algorithm that implements the level of automation of the system. The simulator has been designed and developed following a user-centred design approach in order to take into account the operator’s needs in the communication with the vehicle. The level of automation has been developed following the supervisory control theory which says that the human became a supervisor who sends high level commands, such as part of mission, target, constraints, in then-rule, while the vehicle receives, comprehends and translates such commands into detailed action such as routes or action on the control system. In order to allow the vehicle to calculate and recalculate the safe and efficient route, in term of distance, time and fuel a 3D planning algorithm has been developed. It is based on considering UASs representative of real world systems as objects moving in a virtual environment (terrain, obstacles, and no fly zones) which replicates the airspace. Original obstacle avoidance strategies have been conceived in order to generate mission planes which are consistent with flight rules and with the vehicle performance constraints. The interface is based on a touch screen, used to send high level commands to the vehicle, and a 3D Virtual Display which provides a stereoscopic and augmented visualization of the complex scenario in which the vehicle operates. Furthermore, it is provided with an audio feedback message generator. Simulation tests have been conducted with pilot trainers to evaluate the reliability of the algorithm and the effectiveness and efficiency of the interface in supporting the operator in the supervision of an UAV mission. Results have revealed that the planning algorithm calculate very efficient routes in few seconds, an adequate level of workload is required to command the vehicle and that the 3D based interface provides the operator with a good sense of presence and enhances his awareness of the mission scenario and of the vehicle under his control.

Design and development of new pressure sensors for aerodynamic applications

This artwork reports on two different projects that were carried out during the three years of Doctor of the Philosophy course. In the first years a project regarding Capacitive Pressure Sensors Array for Aerodynamic Applications was developed in the Applied Aerodynamic research team of the Second Faculty of Engineering, University of Bologna, Forlì, Italy, and in collaboration with the ARCES laboratories of the same university. Capacitive pressure sensors were designed and fabricated, investigating theoretically and experimentally the sensor’s mechanical and electrical behaviours by means of finite elements method simulations and by means of wind tunnel tests. During the design phase, the sensor figures of merit are considered and evaluated for specific aerodynamic applications. The aim of this work is the production of low cost MEMS-alternative devices suitable for a sensor network to be implemented in air data system. The last two year was dedicated to a project regarding Wireless Pressure Sensor Network for Nautical Applications. Aim of the developed sensor network is to sense the weak pressure field acting on the sail plan of a full batten sail by means of instrumented battens, providing a real time differential pressure map over the entire sail surface. The wireless sensor network and the sensing unit were designed, fabricated and tested in the faculty laboratories. A static non-linear coupled mechanical-electrostatic simulation, has been developed to predict the pressure versus capacitance static characteristic suitable for the transduction process and to tune the geometry of the transducer to reach the required resolution, sensitivity and time response in the appropriate full scale pressure input A time dependent viscoelastic error model has been inferred and developed by means of experimental data in order to model, predict and reduce the inaccuracy bound due to the viscolelastic phenomena affecting the Mylar® polyester film used for the sensor diaphragm. The development of the two above mentioned subjects are strictly related but presently separately in this artwork.

Materiali a memoria di forma: caratterizzazione e applicazioni nel campo dei beni culturali

Questo lavoro di tesi nasce da un progetto di ricerca promosso nel 2001 dal Prof. Leonardo Seccia (Seconda Facoltà di Ingegneria, sede di Forlì, e C.I.R.A.M., Università di Bologna), dal Prof. Nicola Santopuoli (Facoltà di Architettura Valle Giulia, Sapienza Università di Roma), dal Prof. Ingo Muller e dal Dott. André Musolff (Technical University Berlin, Facultat III, Thermodynamics). Tale progetto ha avuto come obiettivo lo studio, la progettazione e la realizzazione di un dispositivo di ancoraggio in lega a memoria di forma per il restauro di affreschi e mosaici parietali, che presentino distacchi più o meno evidenti fra gli strati di intonaco di supporto, proponendosi come mezzo efficace per la salvaguardia strutturale di tali zone variamente ammalorate. In particolare, è stata programmata una serie di prove di laboratorio per caratterizzare in modo preciso il comportamento del materiale prescelto, al fine di realizzare un prototipo rispondente alle caratteristiche di progetto ed anche per implementare un modello numerico sufficientemente realistico. A questo proposito, è stato anche approfondito il problema della scelta del modello costitutivo più adeguato. Successivamente, i risultati ottenuti sono stati impiegati nella progettazione e realizzazione di nuovi dispositivi in lega a memoria di forma da impiegare nel campo dei beni culturali, fra cui sistemi reversibili per il ricongiungimento di parti fratturate e sistemi di movimentazione intelligenti sia per lastre di protezione di superfici affrescate, sia per finestre da inserire in contesti museali per il controllo del microclima.

Modellazione e simulazione di sistemi meccanici ad elevato numero di gradi di libertà mediante metodi non convenzionali e sistemi CAD

Recent developments in piston engine technology have increased performance in a very significant way. Diesel turbocharged/turbo compound engines, fuelled by jet fuels, have great performances. The focal point of this thesis is the transformation of the FIAT 1900 jtd diesel common rail engine for the installation on general aviation aircrafts like the CESSNA 172. All considerations about the diesel engine are supported by the studies that have taken place in the laboratories of the II Faculty of Engineering in Forlì. This work, mostly experimental, concerns the transformation of the automotive FIAT 1900 jtd – 4 cylinders – turbocharged – diesel common rail into an aircraft engine. The design philosophy of the aluminium alloy basement of the spark ignition engine have been transferred to the diesel version while the pistons and the head of the FIAT 1900 jtd are kept in the aircraft engine. Different solutions have been examined in this work. A first V 90° cylinders version that can develop up to 300 CV and whose weight is 30 kg, without auxiliaries and turbocharging group. The second version is a development of e original version of the diesel 1900 cc engine with an optimized crankshaft, that employ a special steel, 300M, and that is verified for the aircraft requirements. Another version with an augmented stroke and with a total displacement of 2500 cc has been examined; the result is a 30% engine heavier. The last version proposed is a 1600 cc diesel engine that work at 5000 rpm, with a reduced stroke and capable of more than 200 CV; it was inspired to the Yamaha R1 motorcycle engine. The diesel aircraft engine design keeps the bore of 82 mm, while the stroke is reduced to 64.6 mm, so the engine size is reduced along with weight. The basement weight, in GD AlSi 9 MgMn alloy, is 8,5 kg. Crankshaft, rods and accessories have been redesigned to comply to aircraft standards. The result is that the overall size is increased of only the 8% when referred to the Yamaha engine spark ignition version, while the basement weight increases of 53 %, even if the bore of the diesel version is 11% lager. The original FIAT 1900 jtd piston has been slightly modified with the combustion chamber reworked to the compression ratio of 15:1. The material adopted for the piston is the aluminium alloy A390.0-T5 commonly used in the automotive field. The piston weight is 0,5 kg for the diesel engine. The crankshaft is verified to torsional vibrations according to the Lloyd register of shipping requirements. The 300M special steel crankshaft total weight is of 14,5 kg. The result reached is a very small and light engine that may be certified for general aviation: the engine weight, without the supercharger, air inlet assembly, auxiliary generators and high pressure body, is 44,7 kg and the total engine weight, with enlightened HP pump body and the titanium alloy turbocharger is less than 100 kg, the total displacement is 1365 cm3 and the estimated output power is 220 CV. The direct conversion of automotive piston engine to aircrafts pays too huge weight penalties. In fact the main aircraft requirement is to optimize the power to weight ratio in order to obtain compact and fast engines for aeronautical use: this 1600 common rail diesel engine version demonstrates that these results can be reached.

Modelizzazione spazio-temporale delle dinamiche di uso del suolo ed analisi comparativa di differenti approcci predittivi. Uso integrato di SIG e telerilevamento nello studio dei processi di deforestazione nella regione La Joyanca in Peten, Guatemala

L’uso frequente dei modelli predittivi per l’analisi di sistemi complessi, naturali o artificiali, sta cambiando il tradizionale approccio alle problematiche ambientali e di rischio. Il continuo miglioramento delle capacità di elaborazione dei computer facilita l’utilizzo e la risoluzione di metodi numerici basati su una discretizzazione spazio-temporale che permette una modellizzazione predittiva di sistemi reali complessi, riproducendo l’evoluzione dei loro patterns spaziali ed calcolando il grado di precisione della simulazione. In questa tesi presentiamo una applicazione di differenti metodi predittivi (Geomatico, Reti Neurali, Land Cover Modeler e Dinamica EGO) in un’area test del Petén, Guatemala. Durante gli ultimi decenni questa regione, inclusa nella Riserva di Biosfera Maya, ha conosciuto una rapida crescita demografica ed un’incontrollata pressione sulle sue risorse naturali. L’area test puó essere suddivisa in sotto-regioni caratterizzate da differenti dinamiche di uso del suolo. Comprendere e quantificare queste differenze permette una migliore approssimazione del sistema reale; é inoltre necessario integrare tutti i parametri fisici e socio-economici, per una rappresentazione più completa della complessità dell’impatto antropico. Data l’assenza di informazioni dettagliate sull’area di studio, quasi tutti i dati sono stati ricavati dall’elaborazione di 11 immagini ETM+, TM e SPOT; abbiamo poi realizzato un’analisi multitemporale dei cambi uso del suolo passati e costruito l’input per alimentare i modelli predittivi. I dati del 1998 e 2000 sono stati usati per la fase di calibrazione per simulare i cambiamenti nella copertura terrestre del 2003, scelta come data di riferimento per la validazione dei risultati. Quest’ultima permette di evidenziare le qualità ed i limiti per ogni modello nelle differenti sub-regioni.

Influenza della variabilità spaziale sul trasporto reattivo

La tesi ha per obiettivo di quantificare gli effetti che la variabilità spaziale del mezzo poroso ha sull'evoluzione di un sistema geochimico. Le reazioni di dissoluzione o precipiazione di minerali modificano la struttura microscopica del mezzo, e con essa le proprietà idrodinamiche del sistema, la permeabilità in modo particolare. La variabilità spaziale iniziale del mezzo può essere causa della formazione di digitazioni o canalizzazioni? La prima parte della tesi tratta il cambiamento di scala, necessario per passare da una simulazione geostatistica su griglia fine al calcolo di trasporto su una tessellazione più grossolana. Nel caso del codice di calcolo Hytec, che implementa uno schema ai volumi finiti basato su discretizzazione in poligoni di Voronoï, sono stati confrontati diversi metodi di calcolo della permeabilità equivalente, seguendo differenti criteri. La seconda parte riguarda i calcoli di trasporto reattivo condotti su famiglie di simulazioni geostatistiche del mezzo; l'influenza della variabilità spaziale iniziale sull'evoluzione dei sistemi viene quantificata grazie ad opportune grandezze osservabili. Sono state studiate due reazioni distinte: un caso di dissoluzione, in maniera più approfondita, e più rapidamente un caso di precipitazione, il cui effetto complessivo è quello di riequilibrare il sistema.

Evaluation of alkali flooding combined with intermittent flow in carbonate reservoir

The majority of carbonate reservoir is oil-wet, which is an unfavorable condition for oil production. Generally, the total oil recovery after both primary and secondary recovery in an oil-wet reservoir is low. The amount of producible oil by enhanced oil recovery techniques is still large. Alkali substances are proven to be able to reverse rock wettability from oil-wet to water-wet, which is a favorable condition for oil production. However, the wettability reversal mechanism would require a noneconomical aging period to reach the maximum reversal condition. An intermittent flow with the optimum pausing period is then combined with alkali flooding (combination technique) to increase the wettability reversal mechanism and as a consequence, oil recovery is improved. The aims of this study are to evaluate the efficiency of the combination technique and to study the parameters that affect this method. In order to implement alkali flooding, reservoir rock and fluid properties were gathered, e.g. interfacial tension of fluids, rock wettability, etc. The flooding efficiency curves are obtained from core flooding and used as a major criterion for evaluation the performance of technique. The combination technique improves oil recovery when the alkali concentration is lower than 1% wt. (where the wettability reversal mechanism is dominant). The soap plug (that appears when high alkali concentration is used) is absent in this combination as seen from no drop of production rate. Moreover, the use of low alkali concentration limits alkali loss. This combination probably improves oil recovery also in the fractured carbonate reservoirs in which oil is uneconomically produced. The results from the current study indicate that the combination technique is an option that can improve the production of carbonate reservoirs. And a less quantity of alkali is consumed in the process.

Valutazione delle performance degli scalpelli da perforazione: studi teorici, analisi dati e valutazioni tecnico-economiche

The study is aimed to calculate an innovative numerical index for bit performance evaluation called Bit Index (BI), applied on a new type of bit database named Formation Drillability Catalogue (FDC). A dedicated research programme (developed by Eni E&P and the University of Bologna) studied a drilling model for bit performance evaluation named BI, derived from data recorded while drilling (bit records, master log, wireline log, etc.) and dull bit evaluation. This index is calculated with data collected inside the FDC, a novel classification of Italian formations aimed to the geotechnical and geomechanical characterization and subdivisions of the formations, called Minimum Interval (MI). FDC was conceived and prepared at Eni E&P Div., and contains a large number of significant drilling parameters. Five wells have been identified inside the FDC and have been tested for bit performance evaluation. The values of BI are calculated for each bit run and are compared with the values of the cost per metre. The case study analyzes bits of the same type, diameters and run in the same formation. The BI methodology implemented on MI classification of FDC can improve consistently the bit performances evaluation, and it helps to identify the best performer bits. Moreover, FDC turned out to be functional to BI, since it discloses and organizes formation details that are not easily detectable or usable from bit records or master logs, allowing for targeted bit performance evaluations. At this stage of development, the BI methodology proved to be economic and reliable. The quality of bit performance analysis obtained with BI seems also more effective than the traditional “quick look” analysis, performed on bit records, or on the pure cost per metre evaluation.

Valutazione in opera ed in laboratorio della trasmissione laterale nelle tipologie edilizie italiane

L’attività di ricerca del dottorando è stata rivolta allo studio della trasmissione del rumore per via strutturale negli edifici. Questo argomento e' di notevole interesse sia fondamentale che applicativo. Il fenomeno e le problematiche ad essa connesse contribuiscono alla diminuzione delle prestazioni fonoisolanti, sia per le strutture verticali (usualmente valutate rispetto al rumore aereo), sia per quelle orizzontali (valutate anche rispetto al rumore impattivo) ed è tipico degli edifici con struttura portante a telaio e tamponatura in laterizi. Si tratta delle tipiche tipologie edilizie italiane, per le quali il problema risulta amplificato rispetto ad altre tipologie. La metodologia di studio è stata di tipo sperimentale. La scelta è dettata sia dall’insufficiente avanzamento dello stato dell’arte dei metodi di calcolo teorici, o delle loro versioni numeriche, sia dalla necessità di disporre di dati certi da confrontare con i valori forniti dai metodi previsionali semplificati indicati nelle norme UNI (modello CEN); infatti queste ultime sono un recepimento letterale di quelle europee, sebbene esse si basino su tipologie costruttive, materiali e tecniche di realizzazione differenti da quelle comunemente in uso in Italia; da qui la difformità di risultati tra formule previsionali e misurazioni sperimentali. Al fine di realizzare uno studio completo delle principali casistiche della trasmissione laterale sono state utilizzate 6 configurazioni in scala reale, con elementi edilizi diversamente collegati fra loro in modo da simulare i nodi strutturali comunemente realizzati negli edifici. La parte sperimentale della ricerca è stata svolta presso le “Camere Acustiche di Prova” del Laboratorio del Lazzaretto “R. Alessi” del DIENCA. Oltre alle usuali misurazioni di isolamento acustico, sono state eseguite numerose misurazioni di vibrazione. Infatti, dal confronto dei livelli di velocità di vibrazione dei diversi elementi di una struttura, rigidamente connessi, è possibile determinare l’indice di riduzione delle vibrazioni Kij che è la grandezza chiave per modellizzare il fenomeno della trasmissione laterale. La possibilità di determinare sperimentalmente tali valori nel contesto di un lavoro di ricerca finalizzato a determinare i meccanismi di propagazione delle vibrazioni nelle strutture, permette di valutare la precisione delle formule previsionali del modello CEN e di proporne varianti e integrazioni. I valori di Kij così determinati assumono grande importanza anche in fase di progetto, fornendo dati attendibili da utilizzare per la progettazione acustica degli edifici.

Metrologia dei campi di radiazioni di bassa energia

The conversion coefficients from air kerma to ICRU operational dose equivalent quantities for ENEA’s realization of the X-radiation qualities L10-L35 of the ISO “Low Air Kerma rate” series (L), N10-N40 of the ISO “Narrow spectrum” series (N) and H10-H60 of the ISO “High Air-kerma rate” (H) series and two beams at 5 kV and 7.5 kV were determined by utilising X-ray spectrum measurements. The pulse-height spectra were measured using a planar high-purity germanium spectrometer (HPGe) and unfolded to fluence spectra using a stripping procedure then validate with using Monte Carlo generated data of the spectrometer response. HPGe portable detector has a diameter of 8.5 mm and a thickness of 5 mm. The entrance window of the crystal is collimated by a 0.5 mm thick Aluminum ring to an open diameter of 6.5 mm. The crystal is mounted at a distance of 5 mm from the Berillium window (thickness 25.4 micron). The Monte Carlo method (MCNP-4C) was used to calculate the efficiency, escape and Compton curves of a planar high-purity germanium detector (HPGe) in the 5-60 keV energy. These curves were used for the determination of photon spectra produced by the X-ray machine SEIFERT ISOVOLT 160 kV in order to allow a precise characterization of photon beams in the low energy range, according to the ISO 4037. The detector was modelled with the MCNP computer code and validated with experimental data. To verify the measuring and the stripping procedure, the first and the second half-value layers and the air kerma rate were calculated from the counts spectra and compared with the values measured using an a free-air ionization chamber. For each radiation quality, the spectrum was characterized by the parameters given in ISO 4037-1. The conversion coefficients from the air kerma to the ICRU operational quantities Hp(10), Hp(0.07), H’(0.07) and H*(10) were calculated using monoenergetic conversion coefficients. The results are discussed with respect to ISO 4037-4, and compared with published results for low-energy X-ray spectra. The main motivation for this work was the lack of a treatment of the low photon energy region (from a few keV up to about 60 keV).