Caratterizzazione di membrane metalliche e ionomeriche per applicazioni energetiche

The work of this thesis has been focused on the characterization of metallic membranes for the hydrogen purification from steam reforming process and also of perfluorosulphonic acid ionomeric (PFSI) membranes suitable as electrolytes in fuel cell applications. The experimental study of metallic membranes was divided in three sections: synthesis of palladium and silver palladium coatings on porous ceramic support via electroless deposition (ELD), solubility and diffusivity analysis of hydrogen in palladium based alloys (temperature range between 200 and 400 °C up to 12 bar of pressure) and permeation experiments of pure hydrogen and mixtures containing, besides hydrogen, also nitrogen and methane at high temperatures (up to 600 °C) and pressures (up to 10 bar). Sequential deposition of palladium and silver on to porous alumina tubes by ELD technique was carried out using two different procedures: a stirred batch and a continuous flux method. Pure palladium as well as Pd-Ag membranes were produced: the Pd-Ag membranes’ composition is calculated to be close to 77% Pd and 23% Ag by weight which was the target value that correspond to the best performance of the palladium-based alloys. One of the membranes produced showed an infinite selectivity through hydrogen and relatively high permeability value and is suitable for the potential use as a hydrogen separator. The hydrogen sorption in silver palladium alloys was carried out in a gravimetric system on films produced by ELD technique. In the temperature range inspected, up to 400°C, there is still a lack in literature. The experimental data were analyzed with rigorous equations allowing to calculate the enthalpy and entropy values of the Sieverts’ constant; the results were in very good agreement with the extrapolation made with literature data obtained a lower temperature (up to 150 °C). The information obtained in this study would be directly usable in the modeling of hydrogen permeation in Pd-based systems. Pure and mixed gas permeation tests were performed on Pd-based hydrogen selective membranes at operative conditions close to steam-reforming ones. Two membranes (one produced in this work and another produced by NGK Insulators Japan) showed a virtually infinite selectivity and good permeability. Mixture data revealed the existence of non negligible resistances to hydrogen transport in the gas phase. Even if the decrease of the driving force due to polarization concentration phenomena occurs, in principle, in all membrane-based separation systems endowed with high perm-selectivity, an extensive experimental analysis lack, at the moment, in the palladium-based membrane process in literature. Moreover a new procedure has been introduced for the proper comparison of the mass transport resistance in the gas phase and in the membrane. Another object of study was the water vapor sorption and permeation in PFSI membranes with short and long side chains was also studied; moreover the permeation of gases (i.e. He, N2 and O2) in dry and humid conditions was considered. The water vapor sorption showed strong interactions between the hydrophilic groups and the water as revealed from the hysteresis in the sorption-desorption isotherms and thermo gravimetric analysis. The data obtained were used in the modeling of water vapor permeation, that was described as diffusion-reaction of water molecules, and in the humid gases permeation experiments. In the dry gas experiments the permeability and diffusivity was found to increase with temperature and with the equivalent weight (EW) of the membrane. A linear correlation was drawn between the dry gas permeability and the opposite of the equivalent weight of PFSI membranes, based on which the permeability of pure PTFE is retrieved in the limit of high EW. In the other hand O2 ,N2 and He permeability values was found to increase significantly, and in a similar fashion, with water activity. A model that considers the PFSI membrane as a composite matrix with a hydrophilic and a hydrophobic phase was considered allowing to estimate the variation of gas permeability with relative humidity on the basis of the permeability in the dry PFSI membrane and in pure liquid water.

Genetica molecolare dell'autismo: studi di associazione ed analisi di geni candidati

Autism is a neurodevelpmental disorder characterized by impaired verbal communication, limited reciprocal social interaction, restricted interests and repetitive behaviours. Twin and family studies indicate a large genetic contribution to ASDs (Autism Spectrum Disorders). During my Ph.D. I have been involved in several projects in which I used different genetic approaches in order to identify susceptibility genes in autism on chromosomes 2, 7 and X: 1)High-density SNP association and CNV analysis of two Autism Susceptibility Loci. The International Molecular Genetic Study of Autism Consortium (IMGSAC) previously identified linkage loci on chromosomes 7 and 2, termed AUTS1 and AUTS5, respectively. In this study, we evaluated the patterns of linkage disequilibrium (LD) and the distribution of haplotype blocks, utilising data from the HapMap project, across the two strongest peaks of linkage on chromosome 2 and 7. More than 3000 SNPs have been selected in each locus in all known genes, as well as SNPs in non-genic highly conserved sequences. All markers have been genotyped to perform a high-density association analysis and to explore copy number variation within these regions. The study sample consisted of 127 and 126 multiplex families, showing linkage to the AUTS1 and AUTS5 regions, respectively, and 188 gender-matched controls. Association and CNV analysis implicated several new genes, including IMMP2L and DOCK4 on chromosome 7 and ZNF533 and NOSTRIN on the chromosome 2. Particularly, my contribution to this project focused on the characterization of the best candidate gene in each locus: On the AUTS5 locus I carried out a transcript study of ZNF533 in different human tissues to verify which isoforms and start exons were expressed. High transcript variability and a new exon, never described before, has been identified in this analysis. Furthermore, I selected 31 probands for the risk haplotype and performed a mutation screen of all known exons in order to identify novel coding variants associated to autism. On the AUTS1 locus a duplication was detected in one multiplex family that was transmitted from father to an affected son. This duplication interrupts two genes: IMMP2L and DOCK4 and warranted further analysis. Thus, I performed a screening of the cohort of IMGSAC collection (285 multiplex families), using a QMPSF assay (Quantitative Multiplex PCR of Short fluorescent Fragments) to analyse if CNVs in this genic region segregate with autism phenotype and compare their frequency with a sample of 475 UK controls. Evidence for a role of DOCK4 in autism susceptibility was supported by independent replication of association at rs2217262 and the finding of a deletion segregating in a sib-pair family. 2)Analysis of X chromosome inactivation. Skewed X chromosome inactivation (XCI) is observed in females carrying gene mutations involved in several X-linked syndromes. We aimed to estimate the role of X-linked genes in ASD susceptibility by ascertaining the XCI pattern in a sample of 543 informative mothers of children with ASD and in a sample of 164 affected girls. The study sample included families from different european consortia. I analysed the XCI inactivation pattern in a sample of italian mothers from singletons families with ASD and also a control groups (144 adult females and 40 young females). We observed no significant excess of skewed XCI in families with ASD. Interestingly, two mothers and one girl carrying known mutations in X-linked genes (NLGN3, ATRX, MECP2) showed highly skewed XCI, suggesting that ascertainment of XCI could reveal families with X-linked mutations. Linkage analysis was carried out in the subgroup of multiplex families with skewed XCI (≥80:20) and a modest increased allele sharing was obtained in the Xq27-Xq28 region, with a peak Z score of 1.75 close to rs719489. In this region FMR1 and MECP2 have been associated in some cases with austim and therefore represent candidates for the disorder. I performed a mutation screen of MECP2 in 33 unrelated probands from IMGSAC and italian families, showing XCI skewness. Recently, Xq28 duplications including MECP2, have been identified in families with MR, with asymptomatic carrier females showing extreme (>85%) skewing of XCI. For these reason I used the sample of probands from X-skewed families to perform CNV analysis by Real-time quantitative PCR. No duplications have been found in our sample. I have also confirmed all data using as alternative method the MLPA assay (Multiplex Ligation dependent Probe Amplification). 3)ASMT as functional candidate gene for autism. Recently, a possible involvement of the acetylserotonin O-methyltransferase (ASMT) gene in susceptibility to ASDs has been reported: mutation screening of the ASMT gene in 250 individuals from the PARIS collection revealed several rare variants with a likely functional role; Moreover, significant association was reported for two SNPs (rs4446909 and rs5989681) located in one of the two alternative promoters of the gene. To further investigate these findings, I carried out a replication study using a sample of 263 affected individuals from the IMGSAC collection and 390 control individuals. Several rare mutations were identified, including the splice site mutation IVS5+2T>C and the L326F substitution previously reported by Melke et al (2007), but the same rare variants have been found also in control individuals in our study. Interestingly, a new R319X stop mutation was found in a single autism proband of Italian origin and is absent from the entire control sample. Furthermore, no replication has been found in our case-control study typing the SNPs on the ASMT promoter B.

Interazioni tra Glicoproteine che mediano la penetrazione del Virus Herpes Simplex nella cellula e disegno razionale di Peptidi Inibitori

Herpes simplex virus entry into cells requires a multipartite fusion apparatus made of gD, gB and heterodimer gH/gL. gD serves as receptor-binding glycoprotein and trigger of fusion; its ectodomain is organized in a N-terminal domain carrying the receptor-binding sites, and a C-terminal domain carrying the profusion domain, required for fusion but not receptor-binding. gB and gH/gL execute fusion. To understand how the four glycoproteins cross-talk to each other we searched for biochemical defined complexes in infected and transfected cells, and in virions. We report that gD formed complexes with gB in absence of gH/gL, and with gH/gL in absence of gB. Complexes with similar composition were formed in infected and transfected cells. They were also present in virions prior to entry, and did not increase at virus fusion with cell. A panel of gD mutants enabled the preliminary location of part of the binding site in gD to gB to the aa 240-260 portion and downstream, with T306P307 as critical residues, and of the binding site to gH/gL at aa 260-310 portion, with P291P292 as critical residues. The results indicate that gD carries composite independent binding sites for gB and gH/gL, both of which partly located in the profusion domain. The second part of the project dealt with rational design of peptides inhibiting virus entry has been performed. Considering gB and gD, the crystal structure is known, so we designed peptides that dock in the structure or prevent the adoption of the final conformation of target molecule. Considering the other glycoproteins, of which the structure is not known, peptide libraries were analyzed. Among several peptides, some were identified as active, designed on glycoprotein B. Two of them were further analyzed. We identified peptide residues fundamental for the inhibiting activity, suggesting a possible mechanism of action. Furthermore, changing the flexibility of peptides, an increased activity was observed,with an EC50 under 10μM. New approaches will try to demonstrate the direct interaction between these peptides and the target glycoprotein B.

Meccanismi evolutivi dei parapoxvirus: caratterizzazione genomica di pseudocowpoxvirus e messa a punto di sistemi per lo studio delle ricombinazioni

The Poxviruses are a family of double stranded DNA (dsDNA) viruses that cause disease in many species, both vertebrate and invertebrate. Their genomes range in size from 135 to 365 kbp and show conservation in both organization and content. In particular, the central genomic regions of the chordopoxvirus subfamily (those capable of infecting vertebrates) contain 88 genes which are present in all the virus species characterised to date and which mostly occur in the same order and orientation. In contrast, however, the terminal regions of the genomes frequently contain genes that are species or genera-specific and that are not essential for the growth of the virus in vitro but instead often encode factors with important roles in vivo including modulation of the host immune response to infection and determination of the host range of the virus. The Parapoxviruses (PPV), of which Orf virus is the prototypic species, represent a genus within the chordopoxvirus subfamily of Poxviridae and are characterised by their ability to infect ruminants and humans. The genus currently contains four recognised species of virus, bovine papular stomatitis virus (BPSV) and pseudocowpox virus (PCPV) both of which infect cattle, orf virus (OV) that infects sheep and goats, and parapoxvirus of red deer in New Zealand (PVNZ). The ORFV genome has been fully sequenced, as has that of BPSV, and is ~138 kb in length encoding ~132 genes. The vast majority of these genes allow the virus to replicate in the cytoplasm of the infected host cell and therefore encode proteins involved in replication, transcription and metabolism of nucleic acids. These genes are well conserved between all known genera of poxviruses. There is however another class of genes, located at either end of the linear dsDNA genome, that encode proteins which are non-essential for replication and generally dictate host range and virulence of the virus. The non-essential genes are often the most variable within and between species of virus and therefore are potentially useful for diagnostic purposes. Given their role in subverting the host-immune response to infection they are also targets for novel therapeutics. The function of only a relatively small number of these proteins has been elucidated and there are several genes whose function still remains obscure principally because there is little similarity between them and proteins of known function in current sequence databases. It is thought that by selectively removing some of the virulence genes, or at least neutralising the proteins in some way, current vaccines could be improved. The evolution of poxviruses has been proposed to be an adaptive process involving frequent events of gene gain and loss, such that the virus co-evolves with its specific host. Gene capture or horizontal gene transfer from the host to the virus is considered an important source of new viral genes including those likely to be involved in host range and those enabling the virus to interfere with the host immune response to infection. Given the low rate of nucleotide substitution, recombination can be seen as an essential evolutionary driving force although it is likely underestimated. Recombination in poxviruses is intimately linked to DNA replication with both viral and cellular proteins participate in this recombination-dependent replication. It has been shown, in other poxvirus genera, that recombination between isolates and perhaps even between species does occur, thereby providing another mechanism for the acquisition of new genes and for the rapid evolution of viruses. Such events may result in viruses that have a selective advantage over others, for example in re-infections (a characteristic of the PPV), or in viruses that are able to jump the species barrier and infect new hosts. Sequence data related to viral strains isolated from goats suggest that possible recombination events may have occurred between OV and PCPV (Ueda et al. 2003). The recombination events are frequent during poxvirus replication and comparative genomic analysis of several poxvirus species has revealed that recombinations occur frequently on the right terminal region. Intraspecific recombination can occur between strains of the same PPV species, but also interspecific recombination can happen depending on enough sequence similarity to enable recombination between distinct PPV species. The most important pre-requisite for a successful recombination is the coinfection of the individual host by different virus strains or species. Consequently, the following factors affecting the distribution of different viruses to shared target cells need to be considered: dose of inoculated virus, time interval between inoculation of the first and the second virus, distance between the marker mutations, genetic homology. At present there are no available data on the replication dynamics of PPV in permissive and non permissive hosts and reguarding co-infetions there are no information on the interference mechanisms occurring during the simultaneous replication of viruses of different species. This work has been carried out to set up permissive substrates allowing the replication of different PPV species, in particular keratinocytes monolayers and organotypic skin cultures. Furthermore a method to isolate and expand ovine skin stem cells was has been set up to indeep further aspects of viral cellular tropism during natural infection. The study produced important data to elucidate the replication dynamics of OV and PCPV virus in vitro as well as the mechanisms of interference that can arise during co-infection with different viral species. Moreover, the analysis carried on the genomic right terminal region of PCPV 1303/05 contributed to a better knowledge of the viral genes involved in host interaction and pathogenesis as well as to locate recombination breakpoints and genetic homologies between PPV species. Taken together these data filled several crucial gaps for the study of interspecific recombinations of PPVs which are thought to be important for a better understanding of the viral evolution and to improve the biosafety of antiviral therapy and PPV-based vectors.

Riparazione del danno ischemico ostruttivo del miocardio mediante cellule staminali mesenchimali sottoposte a stimolazione elettromeccanica in bioreattore

Nell’ambito dell’ingegneria dei tessuti, la possibilità di rigenerazione del miocardio post-infartuale è un argomento “caldo”, che suscita grandi speranze ma solleva altrettanto grandi interrogativi - sostenuti dal sussistere di dubbi di base sulle scelte operative praticabili. Esiste tuttavia concordanza nel considerare fondamentale l’utilizzo di un “supporto” che possa mantenere nella sede peri-infartuale le cellule competenti. Infatti, la semplice iniezione di cellule staminali per via endovenosa o direttamente nell’area infartuata non si è dimostrata particolarmente efficace, soprattutto a causa della cospicua perdita cellulare che si verifica rapidamente dopo il trapianto. Ci si orienta quindi verso la strategia di seminare cellule in grado di transdifferenziare in senso muscolare cardiaco su un materiale biocompatibile in vitro e di impiantare successivamente il costrutto ottenuto in vivo dove ci si attende il riassorbimento del biomateriale e l’integrazione delle cellule. Tuttavia, mentre in altri settori della medicina - quali ortopedia e dermatologia - l’impiego di pseudotessuti ingegnerizzati ha già permesso di conseguire ottimi risultati nella rigenerazione di tessuti danneggiati, allo stato attuale, i progressi ottenuti nell’ambito della rigenerazione del miocardio infartuato appaiono ancora aneddotici e distanti dall’ottenere protocolli condivisi per l’impiego in clinica. Il lavoro presentato in questa ricerca, condotto grazie alla sinergia di competenze interdisciplinari negli ambiti chimico, biologico e dell’ingegneria biomedica meccanica ed elettronica, è uno studio di fattibilità di una metodica standardizzata in grado di indirizzare cellule staminali mesenchimali (MSCs) indifferenziate verso l’acquisizione in vitro di caratteri fenotipici confrontabili con quelli delle cellule muscolari cardiache attraverso il paradigma della coltura dinamica in bioreattore. Il prototipo di bioreattore impiegato, in quanto sviluppato originalmente nel corso di questa attività di ricerca, presenta rispetto ad altri strumenti descritti l’innovazione e il vantaggio di non richiedere l’utilizzo di un incubatore, in quanto esso stesso permette di coltivare cellule al suo interno in condizioni controllate di temperatura, pH e concentrazione di CO2. La sua flessibilità operativa consente di impostare e controllare da personal computer leggi di moto di qualsiasi forma anche con cicliche molto veloci. Infine, la presenza di estensimetri in grado di misurare finemente la variazione di tensione esercitata sulla matrice polimerica utilizzata, posta in trazione tra due afferraggi, permette di applicare nel tempo una forza di stiramento costante, ottenendo deformazioni controllate e risultati riproducibili in termini di modificazioni cellulari. Il superamento delle problematiche sorte durante la fase di messa a punto del sistema, che deve essere ritenuto parte integrante del lavoro di sviluppo condotto, ha permesso di studiare l’adattamento di MSCs allo stiramento ciclico, mostrando che questo effettivamente determina alcune differenze fenotipiche rispetto al controllo statico. Inoltre le cellule hanno acquistato una disposizione orientata lungo l’asse longitudinale delle fibre, dato questo particolarmente importante se si considera la disposizione ordinata delle cellule del miocardio, le quali costituiscono un vero e proprio sincizio, indispensabile per una diffusione sincrona dell’impulso elettrico di contrazione. La creazione di uno pseudotessuto cardiaco ottimale richiederà ovviamente ulteriore lavoro, ma la metodica qui presentata si propone al tempo stesso come uno strumento di studio e come una strategia operativa per un approccio innovativo e standardizzabile alla medicina rigenerativa del miocardio.

Sviluppo di algoritmi avanzati di analisi e diagnosi combustione in tempo reale per motori endotermici alternativi

Increasingly stringent exhaust emission limits and higher fuel economy are the main drivers of the engine development process. As a consequence, the complexity of the propulsion units and its subsystems increase, due to the extensive use of sensors and actuators needed to obtain a precise control over the combustion phase. Since engine calibration process consumes most of the development time, new tools and methodologies are needed to shorten the development time and increase the performance attainable. Real time combustion analysis, based on the in-cylinder pressure signal, can significantly improve the calibration of the engine control strategies and the development of new algorithms, giving instantaneous feedback on the engine behavior. A complete combustion analysis and diagnosis system has been developed, capable of evaluating the most important indicators about the combustion process, such as indicated mean effective pressure, heat release, mass fraction burned and knock indexes. Such a tool is built on top of a flexible, modular and affordable hardware platform, capable of satisfying the requirements needed for accuracy and precision, but also enabling the use directly on-board the vehicle, due to its small form factor.

Influenza delle caratteristiche quali-quantitative della luce da fonti artificiali sulla fisio-morfologia di piante verdi per interior landscaping

La conoscenza delle esigenze luminose (intensità, spettro, durata minima, massima ed ottimale del fotoperiodo di illuminazione) e della tolleranza alle condizioni degli interni delle piante ad uso decorativo, è di fondamentale importanza per una giusta tecnica di progettazione (dimensionamento e dislocazione dei punti luce) dell’indoor plantscaping. Il lungo periodo di condizionamento al quale queste piante vengono sottoposte, caratterizzato principalmente dalla scarsa disponibilità di luce naturale e dagli alti livelli di concentrazione di CO2 determina una forte influenza sui processi morfo-fisiologici. Il presente studio analizza il fattore luminoso ed è articolato su più punti quali; • caratterizzazione della riposta fotosintetica all’intensità luminosa di 21 delle principali specie a fogliame decorativo comunemente utilizzate nella realizzazione degli spazi verdi indoor, per stabilire quali siano i minimi ed ottimali livelli di PAR tali da garantire una fotosintesi netta positiva e nel complesso le condizioni di maggior benessere per le piante; • quantificazione dell’incremento fotosintetico netto dovuto ad una maggior concentrazione di CO2 negli interni rispetto alla concentrazione CO2 atmosferica esterna, all’aumentare dell’ intensità luminosa artificiale sulle precedenti specie; • monitoraggio dell’andamento delle attività fotosintetiche durante il periodo di illuminazione di 8 ore comunemente utilizzato in un interno ad uso lavorativo, a PAR costante e variabile in Ficus elastica e Dieffenbachia picta, al fine di stabilire quali possano essere le durate e le modalità di somministrazione della luce per rendere massima la fotosintesi netta riducendo al minimo i consumi energetici dovuti all’accensione delle lampade; • valutazione della risposta morfo-fisiologica e fotosintetica a modificazioni dello spettro luminoso mediante l’uso di LED monocromatici colorati ad emissione nel bianco, blu e rosso in Ficus benjamina e Iresine herbistii al fine di stabilire se questo tipo di lampade possano essere utilizzate come fonte integrativa e/o sostitutiva nella realizzazione degli spazi verdi interni. Vengono analizzati il punto si compensazione alla luce (g), il punto di saturazione alla luce (s), l’efficienza quantica (AQE), il punto di respirazione al buio (Rd) e la fotosintesi netta massima (A max) per (Aglaonema commutatum, Asplenium nidus, Anthurium andreanum, Begonia rex, Calathea luoise, Calathea veitchiana, Calathea rufibarba, Calathea zebrina, Codiaeum variegatum, Cthenanthe oppenheimiana, Dieffenbakia picta, Ficus benjamina, Ficus elatica, Ficus longifolia, Fittonia verschaffeltii, Iresine herbistii, Philodendron erubescens, Philodendron pertusum, Potos aureus, Spathiphillum wallisi, Syngonium podophillum ) e classificate le specie in funzione di Amax in quattro categorie; A max < 2 µmol CO2 m-2 s-1, A max compresa tra 2 e 4 µmol CO2 m-2 s-1, Amax cpmpresa tra 4 e 6 µmol CO2 m-2 s-1, Amax > 6 µmol CO2 m-2 s-1, al fine di mettere in risalto la potenzialità fotosintetiche di ogni singola specie. I valori di PAR compresi tra (g) ed (s) forniscono le indicazioni sulle quali basarsi per scegliere una giusta lampada o dimensionare un punto luce per ogni singola specie e/o composizione. È stimata l’influenza di due livelli di concentrazione di CO2 ambientale (400 e 800 ppm) all’incrementare dell’intensità luminosa sul processo fotosintetico delle specie precedenti. Per quasi tutte le specie 800 ppm di CO2 non favoriscono nessun incremento all’attività fotosintetica ad eccezione di Ficus benjamina, Ficus elatica e Syngonium podophillum se non accompagnati da una disponibilità luminosa superiore alle 10 µmol m-2 s-1. Viene monitorato l’andamento dell’attività fotosintetica a PAR costante e variabile (intervallando periodi di 8 minuti a PAR 40 e 80) durante 8 ore di illuminazione su Ficus elastica e Dieffenbachia picta al fine di stabilire la miglior modalità di somministrazione della luce. La fotosintesi netta cumulativa per l’intera durata di illuminazione a PAR costante mostra un calo dopo alcune ore dall’attivazione in Dieffenbackia, e un andamento oscillatorio in Ficus. L’illuminazione alternata consente di raggiungere i quantitativi di CO2 organicata a 80 µmol m-2 s-1 di PAR, dopo 5 ore e mezza sia in Ficus che Dieffenbackia sebbene le potenzialità fotosintetiche delle due piante siano molto differenti. È stato valutato l’effetto dell’illuminazione artificiale mediante LED (15W) a luce bianca, blu e rossa monocromatica in rapporto alla luce neon(36W) bianca tradizionale (con differenti abbinamenti tra le lampade) sui principali parametri morfologici e fisiologici, in Ficus benjamin ‘Variegata’ e Iresine herbistii per verificare se tali fonti possono rappresentare una valida alternativa nella sostituzione o integrazione di altre lampade per gli spazi verdi indoor. Tutte le combinazioni LED indagate possono rappresentare un’alternativa di sostituzione alla coltivazione con neon ed un risparmio energetico di oltre il 50%. Una PAR di 20,6 µmol m-2 s-1 della singola lampada LED bianco è sufficiente per mantenere la pianta in condizioni di sopravvivenza con un consumo di 15W a fronte dei 36W necessari per il funzionamento di ogni neon. La combinazione LED bianco + LED blu monocromatico favorisce il contenimento della taglia della pianta, caratteristica gradita nella fase di utilizzo indoor, una maggior produzione di sostanza secca e un’attività fotosintetica più elevata.