Adaptive wireless multimedia communication systems

In recent years, due to the rapid convergence of multimedia services, Internet and wireless communications, there has been a growing trend of heterogeneity (in terms of channel bandwidths, mobility levels of terminals, end-user quality-of-service (QoS) requirements) for emerging integrated wired/wireless networks. Moreover, in nowadays systems, a multitude of users coexists within the same network, each of them with his own QoS requirement and bandwidth availability. In this framework, embedded source coding allowing partial decoding at various resolution is an appealing technique for multimedia transmissions. This dissertation includes my PhD research, mainly devoted to the study of embedded multimedia bitstreams in heterogenous networks, developed at the University of Bologna, advised by Prof. O. Andrisano and Prof. A. Conti, and at the University of California, San Diego (UCSD), where I spent eighteen months as a visiting scholar, advised by Prof. L. B. Milstein and Prof. P. C. Cosman. In order to improve the multimedia transmission quality over wireless channels, joint source and channel coding optimization is investigated in a 2D time-frequency resource block for an OFDM system. We show that knowing the order of diversity in time and/or frequency domain can assist image (video) coding in selecting optimal channel code rates (source and channel code rates). Then, adaptive modulation techniques, aimed at maximizing the spectral efficiency, are investigated as another possible solution for improving multimedia transmissions. For both slow and fast adaptive modulations, the effects of imperfect channel estimation errors are evaluated, showing that the fast technique, optimal in ideal systems, might be outperformed by the slow adaptive modulation, when a real test case is considered. Finally, the effects of co-channel interference and approximated bit error probability (BEP) are evaluated in adaptive modulation techniques, providing new decision regions concepts, and showing how the widely used BEP approximations lead to a substantial loss in the overall performance.

Evidenze micropaleontologiche e sedimentologiche di cicli deposizionali e climatici circa millenari nei Depositi Tardoquaternari della Piana dell'Arno e del Delta del Po

A multidisciplinary study was carried out on the Late Quaternary-Holocene subsurface deposits of two Mediterranean coastal areas: Arno coastal plain (Northern Tyrrhenian Sea) and Modern Po Delta (Northern Adriatic Sea). Detailed facies analyses, including sedimentological and micropalaeontological (benthic foraminifers and ostracods) investigations, were performed on nine continuously-cored boreholes of variable depth (ca. from 30 meters to100 meters). Six cores were located in the Arno coastal plain and three cores in the Modern Po Delta. To provide an accurate chronological framework, twenty-four organic-rich samples were collected along the fossil successions for radiocarbon dating (AMS 14C). In order to reconstruct the depositional and palaeoenvironmental evolution of the study areas, core data were combined with selected well logs, provided by local companies, along several stratigraphic sections. These sections revealed the presence of a transgressive-regressive (T-R) sequence, composing of continental, coastal and shallow-marine deposits dated to the Late Pleistocene-Holocene period, beneath the Arno coastal plain and the Modern Po Delta. Above the alluvial deposits attributed to the last glacial period, the post-glacial transgressive succession (TST) consists of back-barrier, transgressive barrier and inner shelf deposits. Peak of transgression (MFS) took place around the Late-Middle Holocene transition and was identified by subtle micropalaeontological indicators within undifferentiated fine-grained deposits. Upward a thick prograding succession (HST) records the turnaround to regressive conditions that led to a rapid delta progradation in both study areas. Particularly, the outbuilding of modern-age Po Delta coincides with mud-belt formation during the late HST (ca. 600 cal yr BP), as evidenced by a fossil microfauna similar to the foraminiferal assemblage observed in the present Northern Adriatic mud-belt. A complex interaction between allocyclic and autocyclic factors controlled facies evolution during the highstand period. The presence of local parameters and the absence of a predominant factor prevent from discerning or quantifying consequences of the complex relationships between climate and deltaic evolution. On the contrary transgressive sedimentation seems to be mainly controlled by two allocyclic key factors, sea-level rise and climate variability, that minimized the effects of local parameters on coastal palaeoenvironments. TST depositional architecture recorded in both study areas reflects a well-known millennial-scale variability of sea-level rising trend and climate during the Late glacial-Holocene period. Repeated phases of backswamp development and infilling by crevasse processes (parasequences) were recorded in the subsurface of Modern Po Delta during the early stages of transgression (ca. 11,000-9,500 cal yr BP). In the Arno coastal plain the presence of a deep-incised valley system, probably formed at OSI 3/2 transition, led to the development of a thick (ca. 35-40 m) transgressive succession composed of coastal plain, bay-head delta and estuarine deposits dated to the Last glacial-Early Holocene period. Within the transgressive valley fill sequence, high-resolution facies analyses allowed the identification and lateral tracing of three parasequences of millennial duration. The parasequences, ca. 8-12 meters thick, are bounded by flooding surfaces and show a typical internal shallowing-upward trend evidenced by subtle micropalaeontological investigations. The vertical stacking pattern of parasequences shows a close affinity with the step-like sea-level rising trend occurred between 14,000-8,000 cal years BP. Episodes of rapid sea-level rise and subsequent stillstand phases were paralleled by changes in climatic conditions, as suggested by pollen analyses performed on a core drilled in the proximal section of the Arno palaeovalley (pollen analyses performed by Dr. Marianna Ricci Lucchi). Rapid shifts to warmer climate conditions accompanied episodes of rapid sea-level rise, in contrast stillstand phases occurred during temporary colder climate conditions. For the first time the palaeoclimatic signature of high frequency depositional cycles is clearly documented. Moreover, two of the three "regressive" pulsations, recorded at the top of parasequences by episodes of partial estuary infilling in the proximal and central portions of Arno palaeovalley, may be correlated with the most important cold events of the post-glacial period: Younger Dryas and 8,200 cal yr BP event. The stratigraphic and palaeoclimatic data of Arno coastal plain and Po Delta were compared with those reported for the most important deltaic and coastal systems in the worldwide literature. The depositional architecture of transgressive successions reflects the strong influence of millennial-scale eustatic and climatic variability on worldwide coastal sedimentation during the Late glacial-Holocene period (ca. 14,000-7,000 cal yr BP). The most complete and accurate record of high-frequency eustatic and climatic events are usually found within the transgressive succession of very high accommodation settings, such as incised-valley systems where exceptionally thick packages of Late glacial-Early Holocene deposits are preserved.

Higher-Order Concurrency: Expressiveness and Decidability Results

Higher-order process calculi are formalisms for concurrency in which processes can be passed around in communications. Higher-order (or process-passing) concurrency is often presented as an alternative paradigm to the first order (or name-passing) concurrency of the pi-calculus for the description of mobile systems. These calculi are inspired by, and formally close to, the lambda-calculus, whose basic computational step ---beta-reduction--- involves term instantiation. The theory of higher-order process calculi is more complex than that of first-order process calculi. This shows up in, for instance, the definition of behavioral equivalences. A long-standing approach to overcome this burden is to define encodings of higher-order processes into a first-order setting, so as to transfer the theory of the first-order paradigm to the higher-order one. While satisfactory in the case of calculi with basic (higher-order) primitives, this indirect approach falls short in the case of higher-order process calculi featuring constructs for phenomena such as, e.g., localities and dynamic system reconfiguration, which are frequent in modern distributed systems. Indeed, for higher-order process calculi involving little more than traditional process communication, encodings into some first-order language are difficult to handle or do not exist. We then observe that foundational studies for higher-order process calculi must be carried out directly on them and exploit their peculiarities. This dissertation contributes to such foundational studies for higher-order process calculi. We concentrate on two closely interwoven issues in process calculi: expressiveness and decidability. Surprisingly, these issues have been little explored in the higher-order setting. Our research is centered around a core calculus for higher-order concurrency in which only the operators strictly necessary to obtain higher-order communication are retained. We develop the basic theory of this core calculus and rely on it to study the expressive power of issues universally accepted as basic in process calculi, namely synchrony, forwarding, and polyadic communication.

Development of Clinical Decision Support Systems based on Mathematical Models of Physiological Systems

In the last years of research, I focused my studies on different physiological problems. Together with my supervisors, I developed/improved different mathematical models in order to create valid tools useful for a better understanding of important clinical issues. The aim of all this work is to develop tools for learning and understanding cardiac and cerebrovascular physiology as well as pathology, generating research questions and developing clinical decision support systems useful for intensive care unit patients. I. ICP-model Designed for Medical Education We developed a comprehensive cerebral blood flow and intracranial pressure model to simulate and study the complex interactions in cerebrovascular dynamics caused by multiple simultaneous alterations, including normal and abnormal functional states of auto-regulation of the brain. Individual published equations (derived from prior animal and human studies) were implemented into a comprehensive simulation program. Included in the normal physiological modelling was: intracranial pressure, cerebral blood flow, blood pressure, and carbon dioxide (CO2) partial pressure. We also added external and pathological perturbations, such as head up position and intracranial haemorrhage. The model performed clinically realistically given inputs of published traumatized patients, and cases encountered by clinicians. The pulsatile nature of the output graphics was easy for clinicians to interpret. The manoeuvres simulated include changes of basic physiological inputs (e.g. blood pressure, central venous pressure, CO2 tension, head up position, and respiratory effects on vascular pressures) as well as pathological inputs (e.g. acute intracranial bleeding, and obstruction of cerebrospinal outflow). Based on the results, we believe the model would be useful to teach complex relationships of brain haemodynamics and study clinical research questions such as the optimal head-up position, the effects of intracranial haemorrhage on cerebral haemodynamics, as well as the best CO2 concentration to reach the optimal compromise between intracranial pressure and perfusion. We believe this model would be useful for both beginners and advanced learners. It could be used by practicing clinicians to model individual patients (entering the effects of needed clinical manipulations, and then running the model to test for optimal combinations of therapeutic manoeuvres). II. A Heterogeneous Cerebrovascular Mathematical Model Cerebrovascular pathologies are extremely complex, due to the multitude of factors acting simultaneously on cerebral haemodynamics. In this work, the mathematical model of cerebral haemodynamics and intracranial pressure dynamics, described in the point I, is extended to account for heterogeneity in cerebral blood flow. The model includes the Circle of Willis, six regional districts independently regulated by autoregulation and CO2 reactivity, distal cortical anastomoses, venous circulation, the cerebrospinal fluid circulation, and the intracranial pressure-volume relationship. Results agree with data in the literature and highlight the existence of a monotonic relationship between transient hyperemic response and the autoregulation gain. During unilateral internal carotid artery stenosis, local blood flow regulation is progressively lost in the ipsilateral territory with the presence of a steal phenomenon, while the anterior communicating artery plays the major role to redistribute the available blood flow. Conversely, distal collateral circulation plays a major role during unilateral occlusion of the middle cerebral artery. In conclusion, the model is able to reproduce several different pathological conditions characterized by heterogeneity in cerebrovascular haemodynamics and can not only explain generalized results in terms of physiological mechanisms involved, but also, by individualizing parameters, may represent a valuable tool to help with difficult clinical decisions. III. Effect of Cushing Response on Systemic Arterial Pressure. During cerebral hypoxic conditions, the sympathetic system causes an increase in arterial pressure (Cushing response), creating a link between the cerebral and the systemic circulation. This work investigates the complex relationships among cerebrovascular dynamics, intracranial pressure, Cushing response, and short-term systemic regulation, during plateau waves, by means of an original mathematical model. The model incorporates the pulsating heart, the pulmonary circulation and the systemic circulation, with an accurate description of the cerebral circulation and the intracranial pressure dynamics (same model as in the first paragraph). Various regulatory mechanisms are included: cerebral autoregulation, local blood flow control by oxygen (O2) and/or CO2 changes, sympathetic and vagal regulation of cardiovascular parameters by several reflex mechanisms (chemoreceptors, lung-stretch receptors, baroreceptors). The Cushing response has been described assuming a dramatic increase in sympathetic activity to vessels during a fall in brain O2 delivery. With this assumption, the model is able to simulate the cardiovascular effects experimentally observed when intracranial pressure is artificially elevated and maintained at constant level (arterial pressure increase and bradicardia). According to the model, these effects arise from the interaction between the Cushing response and the baroreflex response (secondary to arterial pressure increase). Then, patients with severe head injury have been simulated by reducing intracranial compliance and cerebrospinal fluid reabsorption. With these changes, oscillations with plateau waves developed. In these conditions, model results indicate that the Cushing response may have both positive effects, reducing the duration of the plateau phase via an increase in cerebral perfusion pressure, and negative effects, increasing the intracranial pressure plateau level, with a risk of greater compression of the cerebral vessels. This model may be of value to assist clinicians in finding the balance between clinical benefits of the Cushing response and its shortcomings. IV. Comprehensive Cardiopulmonary Simulation Model for the Analysis of Hypercapnic Respiratory Failure We developed a new comprehensive cardiopulmonary model that takes into account the mutual interactions between the cardiovascular and the respiratory systems along with their short-term regulatory mechanisms. The model includes the heart, systemic and pulmonary circulations, lung mechanics, gas exchange and transport equations, and cardio-ventilatory control. Results show good agreement with published patient data in case of normoxic and hyperoxic hypercapnia simulations. In particular, simulations predict a moderate increase in mean systemic arterial pressure and heart rate, with almost no change in cardiac output, paralleled by a relevant increase in minute ventilation, tidal volume and respiratory rate. The model can represent a valid tool for clinical practice and medical research, providing an alternative way to experience-based clinical decisions. In conclusion, models are not only capable of summarizing current knowledge, but also identifying missing knowledge. In the former case they can serve as training aids for teaching the operation of complex systems, especially if the model can be used to demonstrate the outcome of experiments. In the latter case they generate experiments to be performed to gather the missing data.

Cluster-derived Gold/Iron catalysts for environmental applications

During the last years we assisted to an exponential growth of scientific discoveries for catalysis by gold and many applications have been found for Au-based catalysts. In the literature there are several studies concerning the use of gold-based catalysts for environmental applications and good results are reported for the catalytic combustion of different volatile organic compounds (VOCs). Recently it has also been established that gold-based catalysts are potentially capable of being effectively employed in fuel cells in order to remove CO traces by preferential CO oxidation in H2-rich streams. Bi-metallic catalysts have attracted increasing attention because of their markedly different properties from either of the costituent metals, and above all their enhanced catalytic activity, selectivity and stability. In the literature there are several studies demostrating the beneficial effect due to the addition of an iron component to gold supported catalysts in terms of enhanced activity, selectivity, resistence to deactivation and prolonged lifetime of the catalyst. In this work we tried to develop a methodology for the preparation of iron stabilized gold nanoparticles with controlled size and composition, particularly in terms of obtaining an intimate contact between different phases, since it is well known that the catalytic behaviour of multi-component supported catalysts is strongly influenced by the size of the metal particles and by their reciprocal interaction. Ligand stabilized metal clusters, with nanometric dimensions, are possible precursors for the preparation of catalytically active nanoparticles with controlled dimensions and compositions. Among these, metal carbonyl clusters are quite attractive, since they can be prepared with several different sizes and compositions and, moreover, they are decomposed under very mild conditions. A novel preparation method was developed during this thesis for the preparation of iron and gold/iron supported catalysts using bi-metallic carbonyl clusters as precursors of highly dispersed nanoparticles over TiO2 and CeO2, which are widely considered two of the most suitable supports for gold nanoparticles. Au/FeOx catalysts were prepared by employing the bi-metallic carbonyl cluster salts [NEt4]4[Au4Fe4(CO)16] (Fe/Au=1) and [NEt4][AuFe4(CO)16] (Fe/Au=4), and for comparison FeOx samples were prepared by employing the homometallic [NEt4][HFe3(CO)11] cluster. These clusters were prepared by Prof. Longoni research group (Department of Physical and Inorganic Chemistry- University of Bologna). Particular attention was dedicated to the optimization of a suitable thermal treatment in order to achieve, apart from a good Au and Fe metal dispersion, also the formation of appropriate species with good catalytic properties. A deep IR study was carried out in order to understand the physical interaction between clusters and different supports and detect the occurrence of chemical reactions between them at any stage of the preparation. The characterization by BET, XRD, TEM, H2-TPR, ICP-AES and XPS was performed in order to investigate the catalysts properties, whit particular attention to the interaction between Au and Fe and its influence on the catalytic activity. This novel preparation method resulted in small gold metallic nanoparticles surrounded by highly dispersed iron oxide species, essentially in an amorphous phase, on both TiO2 and CeO2. The results presented in this thesis confirmed that FeOx species can stabilize small Au particles, since keeping costant the gold content but introducing a higher iron amount a higher metal dispersion was achieved. Partial encapsulation of gold atoms by iron species was observed since the Au/Fe surface ratio was found much lower than bulk ratio and a strong interaction between gold and oxide species, both of iron oxide and supports, was achieved. The prepared catalysts were tested in the total oxidation of VOCs, using toluene and methanol as probe molecules for aromatics and alchols, respectively, and in the PROX reaction. Different performances were observed on titania and ceria catalysts, on both toluene and methanol combustion. Toluene combustion on titania catalyst was found to be enhanced increasing iron loading while a moderate effect on FeOx-Ti activity was achieved by Au addition. In this case toluene combustion was improved due to a higher oxygen mobility depending on enhanced oxygen activation by FeOx and Au/FeOx dispersed on titania. On the contrary ceria activity was strongly decreased in the presence of FeOx, while the introduction of gold was found to moderate the detrimental effect of iron species. In fact, excellent ceria performances are due to its ability to adsorb toluene and O2. Since toluene activation is the determining factor for its oxidation, the partial coverage of ceria sites, responsible of toluene adsorption, by FeOx species finely dispersed on the surface resulted in worse efficiency in toluene combustion. Better results were obtained for both ceria and titania catalysts on methanol total oxidation. In this case, the performances achieved on differently supported catalysts indicate that the oxygen mobility is the determining factor in this reaction. The introduction of gold on both TiO2 and CeO2 catalysts, lead to a higher oxygen mobility due to the weakening of both Fe-O and Ce-O bonds and consequently to enhanced methanol combustion. The catalytic activity was found to strongly depend on oxygen mobility and followed the same trend observed for catalysts reducibility. Regarding CO PROX reaction, it was observed that Au/FeOx titania catalysts are less active than ceria ones, due to the lower reducibility of titania compared to ceria. In fact the availability of lattice oxygen involved in PROX reaction is much higher in the latter catalysts. However, the CO PROX performances observed for ceria catalysts are not really high compared to data reported in literature, probably due to the very low Au/Fe surface ratio achieved with this preparation method. CO preferential oxidation was found to strongly depend on Au particle size but also on surface oxygen reducibility, depending on the different oxide species which can be formed using different thermal treatment conditions or varying the iron loading over the support.

Biomass Gasification - Process analysis and dimensioning aspects for downdraft units and gas cleaning lines

In such territories where food production is mostly scattered in several small / medium size or even domestic farms, a lot of heterogeneous residues are produced yearly, since farmers usually carry out different activities in their properties. The amount and composition of farm residues, therefore, widely change during year, according to the single production process periodically achieved. Coupling high efficiency micro-cogeneration energy units with easy handling biomass conversion equipments, suitable to treat different materials, would provide many important advantages to the farmers and to the community as well, so that the increase in feedstock flexibility of gasification units is nowadays seen as a further paramount step towards their wide spreading in rural areas and as a real necessity for their utilization at small scale. Two main research topics were thought to be of main concern at this purpose, and they were therefore discussed in this work: the investigation of fuels properties impact on gasification process development and the technical feasibility of small scale gasification units integration with cogeneration systems. According to these two main aspects, the present work was thus divided in two main parts. The first one is focused on the biomass gasification process, that was investigated in its theoretical aspects and then analytically modelled in order to simulate thermo-chemical conversion of different biomass fuels, such as wood (park waste wood and softwood), wheat straw, sewage sludge and refuse derived fuels. The main idea is to correlate the results of reactor design procedures with the physical properties of biomasses and the corresponding working conditions of gasifiers (temperature profile, above all), in order to point out the main differences which prevent the use of the same conversion unit for different materials. At this scope, a gasification kinetic free model was initially developed in Excel sheets, considering different values of air to biomass ratio and the downdraft gasification technology as particular examined application. The differences in syngas production and working conditions (process temperatures, above all) among the considered fuels were tried to be connected to some biomass properties, such elementary composition, ash and water contents. The novelty of this analytical approach was the use of kinetic constants ratio in order to determine oxygen distribution among the different oxidation reactions (regarding volatile matter only) while equilibrium of water gas shift reaction was considered in gasification zone, by which the energy and mass balances involved in the process algorithm were linked together, as well. Moreover, the main advantage of this analytical tool is the easiness by which the input data corresponding to the particular biomass materials can be inserted into the model, so that a rapid evaluation on their own thermo-chemical conversion properties is possible to be obtained, mainly based on their chemical composition A good conformity of the model results with the other literature and experimental data was detected for almost all the considered materials (except for refuse derived fuels, because of their unfitting chemical composition with the model assumptions). Successively, a dimensioning procedure for open core downdraft gasifiers was set up, by the analysis on the fundamental thermo-physical and thermo-chemical mechanisms which are supposed to regulate the main solid conversion steps involved in the gasification process. Gasification units were schematically subdivided in four reaction zones, respectively corresponding to biomass heating, solids drying, pyrolysis and char gasification processes, and the time required for the full development of each of these steps was correlated to the kinetics rates (for pyrolysis and char gasification processes only) and to the heat and mass transfer phenomena from gas to solid phase. On the basis of this analysis and according to the kinetic free model results and biomass physical properties (particles size, above all) it was achieved that for all the considered materials char gasification step is kinetically limited and therefore temperature is the main working parameter controlling this step. Solids drying is mainly regulated by heat transfer from bulk gas to the inner layers of particles and the corresponding time especially depends on particle size. Biomass heating is almost totally achieved by the radiative heat transfer from the hot walls of reactor to the bed of material. For pyrolysis, instead, working temperature, particles size and the same nature of biomass (through its own pyrolysis heat) have all comparable weights on the process development, so that the corresponding time can be differently depending on one of these factors according to the particular fuel is gasified and the particular conditions are established inside the gasifier. The same analysis also led to the estimation of reaction zone volumes for each biomass fuel, so as a comparison among the dimensions of the differently fed gasification units was finally accomplished. Each biomass material showed a different volumes distribution, so that any dimensioned gasification unit does not seem to be suitable for more than one biomass species. Nevertheless, since reactors diameters were found out quite similar for all the examined materials, it could be envisaged to design a single units for all of them by adopting the largest diameter and by combining together the maximum heights of each reaction zone, as they were calculated for the different biomasses. A total height of gasifier as around 2400mm would be obtained in this case. Besides, by arranging air injecting nozzles at different levels along the reactor, gasification zone could be properly set up according to the particular material is in turn gasified. Finally, since gasification and pyrolysis times were found to considerably change according to even short temperature variations, it could be also envisaged to regulate air feeding rate for each gasified material (which process temperatures depend on), so as the available reactor volumes would be suitable for the complete development of solid conversion in each case, without even changing fluid dynamics behaviour of the unit as well as air/biomass ratio in noticeable measure. The second part of this work dealt with the gas cleaning systems to be adopted downstream the gasifiers in order to run high efficiency CHP units (i.e. internal engines and micro-turbines). Especially in the case multi–fuel gasifiers are assumed to be used, weightier gas cleaning lines need to be envisaged in order to reach the standard gas quality degree required to fuel cogeneration units. Indeed, as the more heterogeneous feed to the gasification unit, several contaminant species can simultaneously be present in the exit gas stream and, as a consequence, suitable gas cleaning systems have to be designed. In this work, an overall study on gas cleaning lines assessment is carried out. Differently from the other research efforts carried out in the same field, the main scope is to define general arrangements for gas cleaning lines suitable to remove several contaminants from the gas stream, independently on the feedstock material and the energy plant size The gas contaminant species taken into account in this analysis were: particulate, tars, sulphur (in H2S form), alkali metals, nitrogen (in NH3 form) and acid gases (in HCl form). For each of these species, alternative cleaning devices were designed according to three different plant sizes, respectively corresponding with 8Nm3/h, 125Nm3/h and 350Nm3/h gas flows. Their performances were examined on the basis of their optimal working conditions (efficiency, temperature and pressure drops, above all) and their own consumption of energy and materials. Successively, the designed units were combined together in different overall gas cleaning line arrangements, paths, by following some technical constraints which were mainly determined from the same performance analysis on the cleaning units and from the presumable synergic effects by contaminants on the right working of some of them (filters clogging, catalysts deactivation, etc.). One of the main issues to be stated in paths design accomplishment was the tars removal from the gas stream, preventing filters plugging and/or line pipes clogging At this scope, a catalytic tars cracking unit was envisaged as the only solution to be adopted, and, therefore, a catalytic material which is able to work at relatively low temperatures was chosen. Nevertheless, a rapid drop in tars cracking efficiency was also estimated for this same material, so that an high frequency of catalysts regeneration and a consequent relevant air consumption for this operation were calculated in all of the cases. Other difficulties had to be overcome in the abatement of alkali metals, which condense at temperatures lower than tars, but they also need to be removed in the first sections of gas cleaning line in order to avoid corrosion of materials. In this case a dry scrubber technology was envisaged, by using the same fine particles filter units and by choosing for them corrosion resistant materials, like ceramic ones. Besides these two solutions which seem to be unavoidable in gas cleaning line design, high temperature gas cleaning lines were not possible to be achieved for the two larger plant sizes, as well. Indeed, as the use of temperature control devices was precluded in the adopted design procedure, ammonia partial oxidation units (as the only considered methods for the abatement of ammonia at high temperature) were not suitable for the large scale units, because of the high increase of reactors temperature by the exothermic reactions involved in the process. In spite of these limitations, yet, overall arrangements for each considered plant size were finally designed, so that the possibility to clean the gas up to the required standard degree was technically demonstrated, even in the case several contaminants are simultaneously present in the gas stream. Moreover, all the possible paths defined for the different plant sizes were compared each others on the basis of some defined operational parameters, among which total pressure drops, total energy losses, number of units and secondary materials consumption. On the basis of this analysis, dry gas cleaning methods proved preferable to the ones including water scrubber technology in al of the cases, especially because of the high water consumption provided by water scrubber units in ammonia adsorption process. This result is yet connected to the possibility to use activated carbon units for ammonia removal and Nahcolite adsorber for chloride acid. The very high efficiency of this latter material is also remarkable. Finally, as an estimation of the overall energy loss pertaining the gas cleaning process, the total enthalpy losses estimated for the three plant sizes were compared with the respective gas streams energy contents, these latter obtained on the basis of low heating value of gas only. This overall study on gas cleaning systems is thus proposed as an analytical tool by which different gas cleaning line configurations can be evaluated, according to the particular practical application they are adopted for and the size of cogeneration unit they are connected to.

Mediterranean brachiopods: morphological, ecological and phylogenetic aspects

The Brachiopoda of the Marine Protected Area “Secche di Tor Paterno”, Central Tyrrhenian Sea, have been investigated in order to give a first glance of the diversity of the brachiopods of this area and provide a new report on the Mediterranean Brachiopod fauna. Four species were reported: Novocrania anomala (Müller, 1776), Megathiris detruncata (Gmelin, 1790), Joania cordata (Risso,1826) and Argyrotheca cuneata (Risso,1826). For all the four species a morphological analysis was carried out. For the two most abundant species, J.cordata and A. cuneata, a morphometric study, based on thickness/width and length/width scattergrams, was carried out, in order to investigate their variability. Size-frequency distributions relative to the three dimensions of the shell were also computed, aimed at a evaluation of population dynamics of these two species. The results showed that, for both species, the parameters which most determine the rise of the shell during the growth of animal are width and length and that frequency distributions are mainly bi- or plurymodal and that they are difficult to interpret, as reported by other studies. Analysis of drill holes found on the shell of some specimens of the two same species revealed a predatory origin and that three different predators are responsible for them. Partial sequences of two different genetic markers, the Internal Transcribed Spacer 1 (ITS1) and the cytochrome oxidase subunit 1 (COI), were used to investigate the phylogenetic relationship between two populations of the eurybathic brachiopod species Gryphus vitreus (Born,1778) across the strait of Gibraltar. This represents the first genetic population study on brachiopods. Results from AMOVA and Bayesian analysis performed on 31 specimens highlighted no genetic differentiation indicating a likely panmixia, dispite the lecitotrophic development of the species.

Wavelet analysis of heart rate variability related to nocturnal frontal lobe epilepsy seizures

Introduction: Nocturnal frontal lobe epilepsy (NFLE) is a distinct syndrome of partial epilepsy whose clinical features comprise a spectrum of paroxysmal motor manifestations of variable duration and complexity, arising from sleep. Cardiovascular changes during NFLE seizures have previously been observed, however the extent of these modifications and their relationship with seizure onset has not been analyzed in detail. Objective: Aim of present study is to evaluate NFLE seizure related changes in heart rate (HR) and in sympathetic/parasympathetic balance through wavelet analysis of HR variability (HRV). Methods: We evaluated the whole night digitally recorded video-polysomnography (VPSG) of 9 patients diagnosed with NFLE with no history of cardiac disorders and normal cardiac examinations. Events with features of NFLE seizures were selected independently by three examiners and included in the study only if a consensus was reached. Heart rate was evaluated by measuring the interval between two consecutive R-waves of QRS complexes (RRi). RRi series were digitally calculated for a period of 20 minutes, including the seizures and resampled at 10 Hz using cubic spline interpolation. A multiresolution analysis was performed (Daubechies-16 form), and the squared level specific amplitude coefficients were summed across appropriate decomposition levels in order to compute total band powers in bands of interest (LF: 0.039062 - 0.156248, HF: 0.156248 - 0.624992). A general linear model was then applied to estimate changes in RRi, LF and HF powers during three different period (Basal) (30 sec, at least 30 sec before seizure onset, during which no movements occurred and autonomic conditions resulted stationary); pre-seizure period (preSP) (10 sec preceding seizure onset) and seizure period (SP) corresponding to the clinical manifestations. For one of the patients (patient 9) three seizures associated with ictal asystole were recorded, hence he was treated separately. Results: Group analysis performed on 8 patients (41 seizures) showed that RRi remained unchanged during the preSP, while a significant tachycardia was observed in the SP. A significant increase in the LF component was instead observed during both the preSP and the SP (p<0.001) while HF component decreased only in the SP (p<0.001). For patient 9 during the preSP and in the first part of SP a significant tachycardia was observed associated with an increased sympathetic activity (increased LF absolute values and LF%). In the second part of the SP a progressive decrease in HR that gradually exceeded basal values occurred before IA. Bradycardia was associated with an increase in parasympathetic activity (increased HF absolute values and HF%) contrasted by a further increase in LF until the occurrence of IA. Conclusions: These data suggest that changes in autonomic balance toward a sympathetic prevalence always preceded clinical seizure onset in NFLE, even when HR changes were not yet evident, confirming that wavelet analysis is a sensitive technique to detect sudden variations of autonomic balance occurring during transient phenomena. Finally we demonstrated that epileptic asystole is associated with a parasympathetic hypertonus counteracted by a marked sympathetic activation.

A model for diffusive and displacive phase transitions in steels

Heat treatment of steels is a process of fundamental importance in tailoring the properties of a material to the desired application; developing a model able to describe such process would allow to predict the microstructure obtained from the treatment and the consequent mechanical properties of the material. A steel, during a heat treatment, can undergo two different kinds of phase transitions [p.t.]: diffusive (second order p.t.) and displacive (first order p.t.); in this thesis, an attempt to describe both in a thermodynamically consistent framework is made; a phase field, diffuse interface model accounting for the coupling between thermal, chemical and mechanical effects is developed, and a way to overcome the difficulties arising from the treatment of the non-local effects (gradient terms) is proposed. The governing equations are the balance of linear momentum equation, the Cahn-Hilliard equation and the balance of internal energy equation. The model is completed with a suitable description of the free energy, from which constitutive relations are drawn. The equations are then cast in a variational form and different numerical techniques are used to deal with the principal features of the model: time-dependency, non-linearity and presence of high order spatial derivatives. Simulations are performed using DOLFIN, a C++ library for the automated solution of partial differential equations by means of the finite element method; results are shown for different test-cases. The analysis is reduced to a two dimensional setting, which is simpler than a three dimensional one, but still meaningful.

Advances in understanding of osmotic dehydration and vacuum impregnation of fruits

Osmotic Dehydration and Vacuum Impregnation are interesting operations in the food industry with applications in minimal fruit processing and/or freezing, allowing to develop new products with specific innovative characteristics. Osmotic dehydration is widely used for the partial removal of water from cellular tissue by immersion in hypertonic (osmotic) solution. The driving force for the diffusion of water from the tissue is provided by the differences in water chemical potential between the external solution and the internal liquid phase of the cells. Vacuum Impregnation of porous products immersed in a liquid phase consist of reduction of pressure in a solid-liquid system (vacuum step) followed by the restoration of atmospheric pressure (atmospheric step). During the vacuum step the internal gas in the product pores is expanded and partially flows out while during the atmospheric step, there is a compression of residual gas and the external liquid flows into the pores (Fito, 1994). This process is also a very useful unit operation in food engineering as it allows to introduce specific solutes in the tissue which can play different functions (antioxidants, pH regulators, preservatives, cryoprotectants etc.). The present study attempts to enhance our understanding and knowledge of fruit as living organism, interacting dynamically with the environment, and to explore metabolic, structural, physico-chemical changes during fruit processing. The use of innovative approaches and/or technologies such as SAFES (Systematic Approach to Food Engineering System), LF-NMR (Low Frequency Nuclear Magnetic Resonance), GASMAS (Gas in Scattering Media Absorption Spectroscopy) are very promising to deeply study these phenomena. SAFES methodology was applied in order to study irreversibility of the structural changes of kiwifruit during short time of osmotic treatment. The results showed that the deformed tissue can recover its initial state 300 min after osmotic dehydration at 25 °C. The LF-NMR resulted very useful in water status and compartmentalization study, permitting to separate observation of three different water population presented in vacuole, cytoplasm plus extracellular space and cell wall. GASMAS techniques was able to study the pressure equilibration after Vacuum Impregnation showing that after restoration of atmospheric pressure in the solid-liquid system, there was a reminding internal low pressure in the apple tissue that slowly increases until reaching the atmospheric pressure, in a time scale that depends on the vacuum applied during the vacuum step. The physiological response of apple tissue on Vacuum Impregnation process was studied indicating the possibility of vesicular transport within the cells. Finally, the possibility to extend the freezing tolerance of strawberry fruits impregnated with cryoprotectants was proven.

Sustainability indicators for environmental management and decision making

The general objective of this research is to explore theories and methodologies of sustainability indicators, environmental management and decision making disciplines with the operational purpose of producing scientific, robust and relevant information for supporting system understanding and decision making in real case studies. Several tools have been applied in order to increase the understanding of socio-ecological systems as well as providing relevant information on the choice between alternatives. These tools have always been applied having in mind the complexity of the issues and the uncertainty tied to the partial knowledge of the systems under study. Two case studies with specific application to performances measurement (environmental performances in the case of the K8 approach and sustainable development performances in the case of the EU Sustainable Development Strategy) and a case study about the selection of sustainable development indicators amongst Municipalities in Scotland, are discussed in the first part of the work. In the second part of the work, the common denominator among subjects consists in the application of spatial indices and indicators to address operational problems in land use management within the territory of the Ravenna province (Italy). The main conclusion of the thesis is that a ‘perfect’ methodological approach which always produces the best results in assessing sustainability performances does not exist. Rather, there is a pool of correct approaches answering different evaluation questions, to be used when methodologies fit the purpose of the analysis. For this reason, methodological limits and conceptual assumptions as well as consistency and transparency of the assessment, become the key factors for assessing the quality of the analysis.

Reexamining the Role of Incarceration and Stigma in Criminal Law

One of the ways by which the legal system has responded to different sets of problems is the blurring of the traditional boundaries of criminal law, both procedural and substantive. This study aims to explore under what conditions does this trend lead to the improvement of society's welfare by focusing on two distinguishing sanctions in criminal law, incarceration and social stigma. In analyzing how incarceration affects the incentive to an individual to violate a legal standard, we considered the crucial role of the time constraint. This aspect has not been fully explored in the literature on law and economics, especially with respect to the analysis of the beneficiality of imposing either a fine or a prison term. We observed that that when individuals are heterogeneous with respect to wealth and wage income, and when the level of activity can be considered a normal good, only the middle wage and middle income groups can be adequately deterred by a fixed fines alone regime. The existing literature only considers the case of the very poor, deemed as judgment proof. However, since imprisonment is a socially costly way to deprive individuals of their time, other alternatives may be sought such as the imposition of discriminatory monetary fine, partial incapacitation and other alternative sanctions. According to traditional legal theory, the reason why criminal law is obeyed is not mainly due to the monetary sanctions but to the stigma arising from the community’s moral condemnation that accompanies conviction or merely suspicion. However, it is not sufficiently clear whether social stigma always accompanies a criminal conviction. We addressed this issue by identifying the circumstances wherein a criminal conviction carries an additional social stigma. Our results show that social stigma is seen to accompany a conviction under the following conditions: first, when the law coincides with the society's social norms; and second, when the prohibited act provides information on an unobservable attribute or trait of an individual -- crucial in establishing or maintaining social relationships beyond mere economic relationships. Thus, even if the social planner does not impose the social sanction directly, the impact of social stigma can still be influenced by the probability of conviction and the level of the monetary fine imposed as well as the varying degree of correlation between the legal standard violated and the social traits or attributes of the individual. In this respect, criminal law serves as an institution that facilitates cognitive efficiency in the process of imposing the social sanction to the extent that the rest of society is boundedly rational and use judgment heuristics. Paradoxically, using criminal law in order to invoke stigma for the violation of a legal standard may also serve to undermine its strength. To sum, the results of our analysis reveal that the scope of criminal law is narrow both for the purposes of deterrence and cognitive efficiency. While there are certain conditions where the enforcement of criminal law may lead to an increase in social welfare, particularly with respect to incarceration and stigma, we have also identified the channels through which they could affect behavior. Since such mechanisms can be replicated in less costly ways, society should first try or seek to employ these legal institutions before turning to criminal law as a last resort.

La responsabilità del vettore terrestre nel trasporto di cose per conto terzi: riflessi assicurativi.

La ricerca ha ad oggetto l’analisi della disciplina della responsabilità del vettore terrestre di merci per conto terzi ed i riflessi che detta disciplina ha avuto modo di svilupparsi nel mercato assicurativo. L’attenzione è stata rivolta al contratto di trasporto di cose in generale, seguendone la disciplina codicistica e le evoluzioni legislative intervenute. Particolare rilievo assume la novella apportata all’art. 1696 c.c., introdotta dall’art. 10 del Dlgs. 286/2005, grazie alla quale l’ordinamento italiano ha potuto codificare il limite di indennizzo dovuto dal vettore nell’ipotesi di colpa lieve, L’introduzione del limite legale di indennizzo per le ipotesi di responsabilità per perdita o avaria della merce trasportata ha generato nel mondo assicurativo interessanti reazioni. L’elaborato esamina anche l’evoluzione giurisprudenziale formatisi in tema di responsabilità vettoriale, evidenziando il crescente rigore imposto dalla giurisprudenza fondato sul principio del receptum. Tale fenomeno ha visto immediata reazione nel mercato assicurativo il quale, sulla base di testi contrattuali non dissimili tra le diverse compagnie di assicurazioni operanti sul mercato domestico e che traevano origine dai formulari approvati dall’ANIA, ha seguito l’evoluzione giurisprudenziale apportando significative restrizioni al rischio tipico previsto dalle coperture della responsabilità civile vettoriale. La ricerca si è poi focalizzata sull’esame delle più comuni clausole contemplate dalle polizze di assicurazioni di responsabilità civile e sul loro significato alla luce delle disposizioni di legge in materia. Tale analisi riveste preminente interesse poiché consente di verificare in concreto come l’assicurazione possa effettivamente costituire per l’impresa di trasporto non tanto un costo bensì una opportunità di risparmio da un lato ed un modello comportamentale, sebbene indotto, dall’altro lato per il raggiungimento di quei canoni di diligenza che qualsiasi operatore del settore dovrebbe tenere durante l’esecuzione del trasporto ed il cui venir meno determina, come detto, sensibili effetti pregiudizievoli di carattere economico.

Rare and complicated forms of infantile hemangiomas: new therapeutic outlooks

Infantile hemangiomas (IHs) are the most common benign neoplastic pathology of childhood; their natural history generally involves three phases: after the onset, which usually occurs in the first weeks of life, there is the proliferation phase where the IH reaches its maximum development and it is followed by the spontaneous involution which leads to the IH regression. The duration and the extent of these phases may vary widely even though in most of the cases the involution process begins around twelve months of life and the regression, complete or partial, is completed around seventh-ninth year of life. The majority of the IHs does not require any treatment. However, 10%-20% is likely to develop serious complications, functional impairments or aesthetic alterations and entail a timely treatment. Although there is no treatment protocol currently shared, therapies usually used in cases with a complication risk consist in: systemic or intralesional steroids as a first choice; interferon α, vincristine and/or bleomicin as second or third choice and/or surgical treatment. Propranolol, a non-selective beta-blocker, has been used for cardiovascular diseases even in childhood for decades. Since 2008 it has been widely used in the IHs treatment, although it is still "off-label". In literature there are hundreds of cases and some clinical studies that show the effectiveness and safety of this drug for this indication. Thanks to a multidisciplinary team (Dermatologists, Cardiologists, Paediatricians, and Radiologists) of S. Orsola-Malpighi Hospital, a clinical study, which has been previously approved by the ethics committee, is carried out in order to evaluate the efficacy and safety of systemic propranolol in the treatment of IHs in paediatric age. At the end of 2012, 78 patients underwent this treatment: the results we have obtained so far show a good efficacy and safety profile in agreement with the data provided by the literature.

Antipodal random sequences with prescribed second-order statistics: application to Compressive Sensing and UWB system based on DS-CDMA

It is usual to hear a strange short sentence: «Random is better than...». Why is randomness a good solution to a certain engineering problem? There are many possible answers, and all of them are related to the considered topic. In this thesis I will discuss about two crucial topics that take advantage by randomizing some waveforms involved in signals manipulations. In particular, advantages are guaranteed by shaping the second order statistic of antipodal sequences involved in an intermediate signal processing stages. The first topic is in the area of analog-to-digital conversion, and it is named Compressive Sensing (CS). CS is a novel paradigm in signal processing that tries to merge signal acquisition and compression at the same time. Consequently it allows to direct acquire a signal in a compressed form. In this thesis, after an ample description of the CS methodology and its related architectures, I will present a new approach that tries to achieve high compression by design the second order statistics of a set of additional waveforms involved in the signal acquisition/compression stage. The second topic addressed in this thesis is in the area of communication system, in particular I focused the attention on ultra-wideband (UWB) systems. An option to produce and decode UWB signals is direct-sequence spreading with multiple access based on code division (DS-CDMA). Focusing on this methodology, I will address the coexistence of a DS-CDMA system with a narrowband interferer. To do so, I minimize the joint effect of both multiple access (MAI) and narrowband (NBI) interference on a simple matched filter receiver. I will show that, when spreading sequence statistical properties are suitably designed, performance improvements are possible with respect to a system exploiting chaos-based sequences minimizing MAI only.