Magnetohydrodynamic Effects On Mixed Convection Flows In Channels And Ducts

This work focuses on magnetohydrodynamic (MHD) mixed convection flow of electrically conducting fluids enclosed in simple 1D and 2D geometries in steady periodic regime. In particular, in Chapter one a short overview is given about the history of MHD, with reference to papers available in literature, and a listing of some of its most common technological applications, whereas Chapter two deals with the analytical formulation of the MHD problem, starting from the fluid dynamic and energy equations and adding the effects of an external imposed magnetic field using the Ohm's law and the definition of the Lorentz force. Moreover a description of the various kinds of boundary conditions is given, with particular emphasis given to their practical realization. Chapter three, four and five describe the solution procedure of mixed convective flows with MHD effects. In all cases a uniform parallel magnetic field is supposed to be present in the whole fluid domain transverse with respect to the velocity field. The steady-periodic regime will be analyzed, where the periodicity is induced by wall temperature boundary conditions, which vary in time with a sinusoidal law. Local balance equations of momentum, energy and charge will be solved analytically and numerically using as parameters either geometrical ratios or material properties. In particular, in Chapter three the solution method for the mixed convective flow in a 1D vertical parallel channel with MHD effects is illustrated. The influence of a transverse magnetic field will be studied in the steady periodic regime induced by an oscillating wall temperature. Analytical and numerical solutions will be provided in terms of velocity and temperature profiles, wall friction factors and average heat fluxes for several values of the governing parameters. In Chapter four the 2D problem of the mixed convective flow in a vertical round pipe with MHD effects is analyzed. Again, a transverse magnetic field influences the steady periodic regime induced by the oscillating wall temperature of the wall. A numerical solution is presented, obtained using a finite element approach, and as a result velocity and temperature profiles, wall friction factors and average heat fluxes are derived for several values of the Hartmann and Prandtl numbers. In Chapter five the 2D problem of the mixed convective flow in a vertical rectangular duct with MHD effects is discussed. As seen in the previous chapters, a transverse magnetic field influences the steady periodic regime induced by the oscillating wall temperature of the four walls. The numerical solution obtained using a finite element approach is presented, and a collection of results, including velocity and temperature profiles, wall friction factors and average heat fluxes, is provided for several values of, among other parameters, the duct aspect ratio. A comparison with analytical solutions is also provided, as a proof of the validity of the numerical method. Chapter six is the concluding chapter, where some reflections on the MHD effects on mixed convection flow will be made, in agreement with the experience and the results gathered in the analyses presented in the previous chapters. In the appendices special auxiliary functions and FORTRAN program listings are reported, to support the formulations used in the solution chapters.

Mixed Mode Fracture Behaviour of Piezoelectric Materials

Piezoelectrics present an interactive electromechanical behaviour that, especially in recent years, has generated much interest since it renders these materials adapt for use in a variety of electronic and industrial applications like sensors, actuators, transducers, smart structures. Both mechanical and electric loads are generally applied on these devices and can cause high concentrations of stress, particularly in proximity of defects or inhomogeneities, such as flaws, cavities or included particles. A thorough understanding of their fracture behaviour is crucial in order to improve their performances and avoid unexpected failures. Therefore, a considerable number of research works have addressed this topic in the last decades. Most of the theoretical studies on this subject find their analytical background in the complex variable formulation of plane anisotropic elasticity. This theoretical approach bases its main origins in the pioneering works of Muskelishvili and Lekhnitskii who obtained the solution of the elastic problem in terms of independent analytic functions of complex variables. In the present work, the expressions of stresses and elastic and electric displacements are obtained as functions of complex potentials through an analytical formulation which is the application to the piezoelectric static case of an approach introduced for orthotropic materials to solve elastodynamics problems. This method can be considered an alternative to other formalisms currently used, like the Stroh’s formalism. The equilibrium equations are reduced to a first order system involving a six-dimensional vector field. After that, a similarity transformation is induced to reach three independent Cauchy-Riemann systems, so justifying the introduction of the complex variable notation. Closed form expressions of near tip stress and displacement fields are therefore obtained. In the theoretical study of cracked piezoelectric bodies, the issue of assigning consistent electric boundary conditions on the crack faces is of central importance and has been addressed by many researchers. Three different boundary conditions are commonly accepted in literature: the permeable, the impermeable and the semipermeable (“exact”) crack model. This thesis takes into considerations all the three models, comparing the results obtained and analysing the effects of the boundary condition choice on the solution. The influence of load biaxiality and of the application of a remote electric field has been studied, pointing out that both can affect to a various extent the stress fields and the angle of initial crack extension, especially when non-singular terms are retained in the expressions of the electro-elastic solution. Furthermore, two different fracture criteria are applied to the piezoelectric case, and their outcomes are compared and discussed. The work is organized as follows: Chapter 1 briefly introduces the fundamental concepts of Fracture Mechanics. Chapter 2 describes plane elasticity formalisms for an anisotropic continuum (Eshelby-Read-Shockley and Stroh) and introduces for the simplified orthotropic case the alternative formalism we want to propose. Chapter 3 outlines the Linear Theory of Piezoelectricity, its basic relations and electro-elastic equations. Chapter 4 introduces the proposed method for obtaining the expressions of stresses and elastic and electric displacements, given as functions of complex potentials. The solution is obtained in close form and non-singular terms are retained as well. Chapter 5 presents several numerical applications aimed at estimating the effect of load biaxiality, electric field, considered permittivity of the crack. Through the application of fracture criteria the influence of the above listed conditions on the response of the system and in particular on the direction of crack branching is thoroughly discussed.

Analysis and improvements of four-wire power converters for electric vehicle chargers

A robust and well-distributed backbone charging network is the priority to ensure widespread electrification of road transport, providing a driving experience similar to that of internal combustion engine vehicles. International standards set multiple technical targets for on-board and off-board electric vehicle chargers; output voltage levels, harmonic emissions, and isolation requirements strongly influence the design of power converters. Additionally, smart-grid services such as vehicle-to-grid and vehicle-to-vehicle require the implementation of bi-directional stages that inevitably increase system complexity and component count. To face these design challenges, the present thesis provides a rigorous analysis of four-leg and split-capacitor three-phase four-wire active front-end topologies focusing on the harmonic description under different modulation techniques and conditions. The resulting analytical formulation paves the way for converter performance improvements while maintaining regulatory constraints and technical requirements under control. Specifically, split-capacitor inverter current ripple was characterized as providing closed-form formulations valid for every sub-case ranging from synchronous to interleaved PWM. Outcomes are the base for a novel variable switching PWM technique capable of mediating harmonic content limitation and switching loss reduction. A similar analysis is proposed for four-leg inverters with a broad range of continuous and discontinuous PWM modulations. The general superiority of discontinuous PWM modulation in reducing switching losses and limiting harmonic emission was demonstrated. Developments are realized through a parametric description of the neutral wire inductor. Finally, a novel class of integrated isolated converter topologies is proposed aiming at the neutral wire delivery without employing extra switching components rather than the one already available in typical three-phase inverter and dual-active-bridge back-to-back configurations. The fourth leg was integrated inside the dual-active-bridge input bridge providing relevant component count savings. A novel modified single-phase-shift modulation technique was developed to ensure a seamless transition between working conditions like voltage level and power factor. Several simulations and experiments validate the outcomes.

Analytical challenges in the fields of Nanobioscience and Nanobiotecnology: integrated methods for separation and characterization

Nano(bio)science and nano(bio)technology play a growing and tremendous interest both on academic and industrial aspects. They are undergoing rapid developments on many fronts such as genomics, proteomics, system biology, and medical applications. However, the lack of characterization tools for nano(bio)systems is currently considered as a major limiting factor to the final establishment of nano(bio)technologies. Flow Field-Flow Fractionation (FlFFF) is a separation technique that is definitely emerging in the bioanalytical field, and the number of applications on nano(bio)analytes such as high molar-mass proteins and protein complexes, sub-cellular units, viruses, and functionalized nanoparticles is constantly increasing. This can be ascribed to the intrinsic advantages of FlFFF for the separation of nano(bio)analytes. FlFFF is ideally suited to separate particles over a broad size range (1 nm-1 μm) according to their hydrodynamic radius (rh). The fractionation is carried out in an empty channel by a flow stream of a mobile phase of any composition. For these reasons, fractionation is developed without surface interaction of the analyte with packing or gel media, and there is no stationary phase able to induce mechanical or shear stress on nanosized analytes, which are for these reasons kept in their native state. Characterization of nano(bio)analytes is made possible after fractionation by interfacing the FlFFF system with detection techniques for morphological, optical or mass characterization. For instance, FlFFF coupling with multi-angle light scattering (MALS) detection allows for absolute molecular weight and size determination, and mass spectrometry has made FlFFF enter the field of proteomics. Potentialities of FlFFF couplings with multi-detection systems are discussed in the first section of this dissertation. The second and the third sections are dedicated to new methods that have been developed for the analysis and characterization of different samples of interest in the fields of diagnostics, pharmaceutics, and nanomedicine. The second section focuses on biological samples such as protein complexes and protein aggregates. In particular it focuses on FlFFF methods developed to give new insights into: a) chemical composition and morphological features of blood serum lipoprotein classes, b) time-dependent aggregation pattern of the amyloid protein Aβ1-42, and c) aggregation state of antibody therapeutics in their formulation buffers. The third section is dedicated to the analysis and characterization of structured nanoparticles designed for nanomedicine applications. The discussed results indicate that FlFFF with on-line MALS and fluorescence detection (FD) may become the unparallel methodology for the analysis and characterization of new, structured, fluorescent nanomaterials.

Analytical methods for modeling elastic metasurfaces

This dissertation aims at developing advanced analytical tools able to model surface waves propagating in elastic metasurfaces. In particular, four different objectives are defined and pursued throughout this work to enrich the description of the metasurface dynamics. First, a theoretical framework is developed to describe the dispersion properties of a seismic metasurface composed of discrete resonators placed on a porous medium considering part of it fully saturated. Such a model combines classical elasticity theory, Biot’s poroelasticity and an effective medium approach to describe the metasurface dynamics and its coupling with the poroelastic substrate. Second, an exact formulation based on the multiple scattering theory is developed to extend the two-dimensional classical Lamb’s problem to the case of an elastic half-space coupled to an arbitrary number of discrete surface resonators. To this purpose, the incident wavefield generated by a harmonic source and the scattered field generated by each resonator are calculated. The substrate wavefield is then obtained as solutions of the coupled problem due to the interference of the incident field and the multiple scattered fields of the oscillators. Third, the above discussed formulation is extended to three-dimensional contexts. The purpose here is to investigate the dynamic behavior and the topological properties of quasiperiodic elastic metasurfaces. Finally, the multiple scattering formulation is extended to model flexural metasurfaces, i.e., an array of thin plates. To this end, the resonant plates are modeled by means of their equivalent impedance, derived by exploiting the Kirchhoff plate theory. The proposed formulation permits the treatment of a general flexural metasurface, with no limitation on the number of plates and the configuration taken into account. Overall, the proposed analytical tools could pave the way for a better understanding of metasurface dynamics and their implementation in engineered devices.

Food safety in wine: optimization of analytical controls and evaluation of production technologies

This PhD thesis has been proposed to validate and then apply innovative analytical methodologies for the determination of compounds with harmful impact on human health, such as biogenic amines and ochratoxin A in wines. Therefore, the influence of production technology (pH, amino acids precursor and use of different malolactic starters) on biogenic amines content in wines was evaluated. An HPLC method for simultaneous determination of amino acids and amines with precolumnderivatization with 9-Fluorenyl-methoxycarbonyl chloride (FMOC-Cl) and UV detection was developed. Initially, the influence of pH, time of derivatization, gradient profile were studied. In order to improve the separation of amino acids and amines and reduce the time of analysis, it was decided to study the influence of different flows and the use of different columns in the chromatographic method. Firstly, a C18 Luna column was used and later two monolithic columns Chromolith in series. It appeared to be suitable for an easy, precise and accurate determination of a relatively large number of amino acids and amines in wines. This method was then applied on different wines produced in the Emilia Romagna region. The investigation permitted to discriminate between red and white wines. Amino acids content is related to the winemaking process. Biogenic amines content in these wines does not represent a possible toxicological problem for human health. The results of the study of influence of technologies and wine composition demonstrated that pH of wines and amino acids content are the most important factors. Particularly wines with pH > 3,5 show higher concentration of biogenic amines than wines with lower pH. The enrichment of wines by nutrients also influences the content of some biogenic amines that are higher in wines added with amino acids precursors. In this study, amino acids and biogenic amines are not statistically affected by strain of lactic acid bacteria inoculated as a starter for malolactic fermentation. An evaluation of different clean-up (SPE-MycoSep; IACs and LLE) and determination methods (HPLC and ELISA) of ochratoxin A was carried out. The results obtained proved that the SPE clean-up are reliable at the same level while the LLE procedures shows lowest recovery. The ELISA method gave a lower determination and a low reproducibility than HPLC method.

Luminescent Systems for Genomics and Proteomics

The present PhD project was focused on the development of new tools and methods for luminescence-based techniques. In particular, the ultimate goal was to present substantial improvements to the currently available technologies for both research and diagnostic in the fields of biology, proteomics and genomics. Different aspects and problems were investigated, requiring different strategies and approaches. The whole work was thus divided into separate chapters, each based on the study of one specific aspect of luminescence: Chemiluminescence, Fluorescence and Electrochemiluminescence. CHAPTER 1, Chemiluminescence The work on luminol-enhancer solution lead to a new luminol solution formulation with 1 order of magnitude lower detection limit for HRP. This technology was patented with Cyanagen brand and is now sold worldwide for Western Blot and ELISA applications. CHAPTER 2, Fluorescescence The work on dyed-doped silica nanoparticles is marking a new milestone in the development of nanotechnologies for biological applications. While the project is still in progress, preliminary studies on model structures are leading to very promising results. The improved brightness of these nano-sized objects, their simple synthesis and handling, their low toxicity will soon turn them, we strongly believe, into a new generation of fluorescent labels for many applications. CHAPTER 3, Electrochemiluminescence The work on electrochemiluminescence produced interesting results that can potentially turn into great improvements from an analytical point of view. Ru(bpy)3 derivatives were employed both for on-chip microarray (Chapter 3.1) and for microscopic imaging applications (Chapter 3.2). The development of these new techniques is still under investigation, but the obtained results confirm the possibility to achieve the final goal. Furthermore the development of new ECL-active species (Chapter 3.3, 3.4, 3.5) and their use in these applications can significantly improve overall performances, thus helping to spread ECL as powerful analytical tool for routinary techniques. To conclude, the results obtained are of strong value to largely increase the sensitivity of luminescence techniques, thus fulfilling the expectation we had at the beginning of this research work.

Two fluid numerical model for coastal applications

Wave breaking is an important coastal process, influencing hydro-morphodynamic processes such as turbulence generation and wave energy dissipation, run-up on the beach and overtopping of coastal defence structures. During breaking, waves are complex mixtures of air and water (“white water”) whose properties affect velocity and pressure fields in the vicinity of the free surface and, depending on the breaker characteristics, different mechanisms for air entrainment are usually observed. Several laboratory experiments have been performed to investigate the role of air bubbles in the wave breaking process (Chanson & Cummings, 1994, among others) and in wave loading on vertical wall (Oumeraci et al., 2001; Peregrine et al., 2006, among others), showing that the air phase is not negligible since the turbulent energy dissipation involves air-water mixture. The recent advancement of numerical models has given valuable insights in the knowledge of wave transformation and interaction with coastal structures. Among these models, some solve the RANS equations coupled with a free-surface tracking algorithm and describe velocity, pressure, turbulence and vorticity fields (Lara et al. 2006 a-b, Clementi et al., 2007). The single-phase numerical model, in which the constitutive equations are solved only for the liquid phase, neglects effects induced by air movement and trapped air bubbles in water. Numerical approximations at the free surface may induce errors in predicting breaking point and wave height and moreover, entrapped air bubbles and water splash in air are not properly represented. The aim of the present thesis is to develop a new two-phase model called COBRAS2 (stands for Cornell Breaking waves And Structures 2 phases), that is the enhancement of the single-phase code COBRAS0, originally developed at Cornell University (Lin & Liu, 1998). In the first part of the work, both fluids are considered as incompressible, while the second part will treat air compressibility modelling. The mathematical formulation and the numerical resolution of the governing equations of COBRAS2 are derived and some model-experiment comparisons are shown. In particular, validation tests are performed in order to prove model stability and accuracy. The simulation of the rising of a large air bubble in an otherwise quiescent water pool reveals the model capability to reproduce the process physics in a realistic way. Analytical solutions for stationary and internal waves are compared with corresponding numerical results, in order to test processes involving wide range of density difference. Waves induced by dam-break in different scenarios (on dry and wet beds, as well as on a ramp) are studied, focusing on the role of air as the medium in which the water wave propagates and on the numerical representation of bubble dynamics. Simulations of solitary and regular waves, characterized by both spilling and plunging breakers, are analyzed with comparisons with experimental data and other numerical model in order to investigate air influence on wave breaking mechanisms and underline model capability and accuracy. Finally, modelling of air compressibility is included in the new developed model and is validated, revealing an accurate reproduction of processes. Some preliminary tests on wave impact on vertical walls are performed: since air flow modelling allows to have a more realistic reproduction of breaking wave propagation, the dependence of wave breaker shapes and aeration characteristics on impact pressure values is studied and, on the basis of a qualitative comparison with experimental observations, the numerical simulations achieve good results.

Indagine sulla nozione di fatto urbano ne L'architettura della città di Aldo Rossi

Questa tesi di dottorato di ricerca ha come oggetto la nozione di fatto urbano elaborata e presentata da Aldo Rossi nel libro L’architettura della città edito nel 1966. Ne L’architettura della città sono molteplici le definizioni e le forme con cui è enunciata la nozione di fatto urbano. Nel corso della tesi si è indagato come la costruzione nel tempo di questo concetto è stata preceduta da diversi studi giovanili intrapresi dal 1953, poi riorganizzati e sintetizzati a partire dal 1963 in un quaderno manoscritto dal titolo “Manuale di urbanistica”, in diversi appunti e in due quaderni manoscritti. Il lavoro di ricerca ha ricostruito la formulazione della nozione di fatto urbano attraverso gli scritti di Rossi. In questa direzione la rilevazione della partecipazione di Rossi a dibattiti, seminari, riviste, corsi universitari o ricerche accademiche è apparsa di fondamentale importanza, per comprendere la complessità di un lavoro non riconducibile a dei concetti disciplinari, ma alla formazione di una teoria trasmissibile. Il tentativo di comprendere e spiegare la nozione di fatto urbano ha condotto ad esaminare l’accezione con cui Rossi compone L’architettura della città, che egli stesso assimila ad un trattato. L’analisi ha identificato come la composizione del libro non è direttamente riferibile ad un uso classico della stesura editoriale del trattato, la quale ha tra i riferimenti più noti nel passato la promozione di una pratica corretta come nel caso vitruviano o un’impalcatura instauratrice di una nuova categoria come nel caso dell’Alberti. La mancanza di un sistema globale e prescrittivo a differenza dei due libri fondativi e il rimando non immediato alla stesura di un trattato classico è evidente ne L’architettura della città. Tuttavia la possibilità di condurre la ricerca su una serie di documenti inediti ha permesso di rilevare come negli scritti a partire dal 1953, sia maturata una trattazione delle questioni centrali alla nozione di fatto urbano ricca di intuizioni, che aspirano ad un’autonomia, sintetizzate, seppure in modo non sistematico, nella stesura del celebre libro. Si è così cercato di mettere in luce la precisazione nel tempo della nozione di fatto urbano e della sua elaborazione nei molteplici scritti antecedenti la pubblicazione de L’architettura della città, precisando come Rossi, pur costruendo su basi teoriche la nozione di fatto urbano, ne indichi una visione progressiva, ossia un uso operativo sulla città. La ricerca si è proposta come obiettivo di comprendere le radici culturali della nozione di fatto urbano sia tramite un’esplorazione degli interessi di Rossi nel suo percorso formativo sia rispetto alla definizione della struttura materiale del fatto urbano che Rossi individua nelle permanenze e che alimenta nella sua definizione con differenti apporti derivanti da altre discipline. Compito di questa ricerca è stato rileggere criticamente il percorso formativo compiuto da Rossi, a partire dal 1953, sottolinearne gli ambiti innovativi e precisarne i limiti descrittivi che non vedranno mai la determinazione di una nozione esatta, ma piuttosto la strutturazione di una sintesi complessa e ricca di riferimenti ad altri studi. In sintesi la tesi si compone di tre parti: 1. la prima parte, dal titolo “La teoria dei fatti urbani ne L’architettura della città”, analizza il concetto di fatto urbano inserendolo all’interno del più generale contesto teorico contenuto nel libro L’architettura della città. Questo avviene tramite la scomposizione del libro, la concatenazione delle sue argomentazioni e la molteplicità delle fonti esplicitamente citate da Rossi. In questo ambito si precisa la struttura del libro attraverso la rilettura dei riferimenti serviti a Rossi per comporre il suo progetto teorico. Inoltre si ripercorre la sua vita attraverso le varie edizioni, le ristampe, le introduzioni e le illustrazioni. Infine si analizza il ruolo del concetto di fatto urbano nel libro rilevando come sia posto in un rapporto paritetico con il titolo del libro, conseguendone un’accezione di «fatto da osservare» assimilabile all’uso proposto dalla geografia urbana francese dei primi del Novecento. 2. la seconda parte, dal titolo “La formazione della nozione di fatto urbano 1953-66”, è dedicata alla presentazione dell’elaborazione teorica negli scritti di Rossi prima de L’architettura della città, ossia dal 1953 al 1966. Questa parte cerca di descrivere le radici culturali di Rossi, le sue collaborazioni e i suoi interessi ripercorrendo la progressiva definizione della concezione di città nel tempo. Si è analizzato il percorso maturato da Rossi e i documenti scritti fin dagli anni in cui era studente alla Facoltà di Architettura Politecnico di Milano. Emerge un quadro complesso in cui i primi saggi, gli articoli e gli appunti testimoniano una ricerca intellettuale tesa alla costruzione di un sapere sullo sfondo del realismo degli anni Cinquanta. Rossi matura infatti un impegno culturale che lo porta dopo la laurea ad affrontare discorsi più generali sulla città. In particolare la sua importante collaborazione con la rivista Casabella-continuità, con il suo direttore Ernesto Nathan Rogers e tutto il gruppo redazionale segnano il periodo successivo in cui compare l’interesse per la letteratura urbanistica, l’arte, la sociologia, la geografia, l’economia e la filosofia. Seguono poi dal 1963 gli anni di lavoro insieme al gruppo diretto da Carlo Aymonino all’Istituto Universitario di Architettura di Venezia, e in particolare le ricerche sulla tipologia edilizia e la morfologia urbana, che portano Rossi a compiere una sintesi analitica per la fondazione di una teoria della città. Dall’indagine si rileva infatti come gli scritti antecedenti L’architettura della città sviluppano lo studio dei fatti urbani fino ad andare a costituire il nucleo teorico di diversi capitoli del libro. Si racconta così la genesi del libro, la cui scrittura si è svolta nell’arco di due anni, e le aspirazioni che hanno portato quello che era stato concepito come un “manuale d’urbanistica” a divenire quello che Rossi definirà “l’abbozzo di un trattato” per la formulazione di una scienza urbana. 3. la terza parte, dal titolo “La struttura materiale dei fatti urbani: la teoria della permanenza”, indaga monograficamente lo studio della città come un fatto materiale, un manufatto, la cui costruzione è avvenuta nel tempo e del tempo mantiene le tracce. Sul tema della teoria della permanenza è stato importante impostare un confronto con il dibattito vivo negli anni della ricostruzione dopo la guerra intorno ai temi delle preesistenze ambientali nella ricostruzione negli ambienti storici. Sono emersi fin da subito importanti la relazione con Ernesto Nathan Rogers, le discussioni sulle pagine di Casabella-Continuità, la partecipazione ad alcuni dibatti e ricerche. Si è inoltre Rilevato l’uso di diversi termini mutuati dalle tesi filosofiche di alcune personalità come Antonio Banfi e Enzo Paci, poi elaborati dal nucleo redazionale di Casabella-Continuità, di cui faceva parte anche Rossi. Sono così emersi alcuni spostamenti di senso e la formulazione di un vocabolario di termini all’interno della complessa vicenda della cultura architettonica degli anni Cinquanta e Sessanta. 1. Si è poi affrontato questo tema analizzando le forme con cui Rossi presenta la definizione della teoria della permanenza e i contributi desunti da alcuni autori per la costruzione scientifica di una teoria dell’architettura, il cui fine è quello di essere trasmissibile e di offrire strumenti di indagine concreti. Questa ricerca ha permesso di ipotizzare come il lavoro dei geografi francesi della prima metà del XX secolo, e in particolare il contributo più rilevante di Marcel Poëte e di Pierre Lavedan, costituiscono le fonti principali e il campo d’indagine maggiormente esplorato da Rossi per definire la teoria della permanenza e i monumenti. Le permanenze non sono dunque presentate ne L’architettura della città come il “tutto”, ma emergono da un metodo che sceglie di isolare i fatti urbani permanenti, consentendo così di compiere un’ipotesi su “ciò che resta” dopo le trasformazioni continue che operano nella città. Le fonti su cui ho lavorato sono state quelle annunciate da Rossi ne L’architettura della città, e più precisamente i testi nelle edizioni da lui consultate. Anche questo lavoro ha permesso un confronto dei testi che ha fatto emergere ne L’architettura della città l’uso di termini mutuati da linguaggi appartenenti ad altre discipline e quale sia l’uso di concetti estrapolati nella loro interezza. Presupposti metodologici Della formulazione della nozione di fatto urbano si sono indagate l’originalità dell’espressione, le connessioni presunte o contenute negli studi di Rossi sulla città attraverso la raccolta di fonti dirette e indirette che sono andate a formare un notevole corpus di scritti. Le fonti dirette più rilevanti sono state trovare nelle collezioni speciali del Getty Research Institute di Los Angeles in cui sono conservati gli Aldo Rossi Papers, questo archivio comprende materiali inediti dal 1954 al 1988. La natura dei materiali si presenta sotto forma di manoscritti, dattiloscritti, quaderni, documenti ciclostilati, appunti sparsi e una notevole quantità di corrispondenza. Negli Aldo Rossi Papers si trovano anche 32 dei 47 Quaderni Azzurri, le bozze de L’architettura della città e dell’ Autobiografia Scientifica. Per quanto riguarda in particolare L’architettura della città negli Aldo Rossi Papers sono conservati: un quaderno con il titolo “Manuale d’urbanistica, giugno 1963”, chiara prima bozza del libro, degli “Appunti per libro urbanistica estate/inverno 1963”, un quaderno con la copertina rossa datato 20 settembre 1964-8 agosto 1965 e un quaderno con la copertina blu datato 30 agosto 1965-15 dicembre 1965. La possibilità di accedere a questo archivio ha permesso di incrementare la bibliografia relativa agli studi giovanili consentendo di rileggere il percorso culturale in cui Rossi si è formato. E’ così apparsa fondamentale la rivalutazione di alcune questioni relative al realismo socialista che hanno portato a formare un più preciso quadro dei primi scritti di Rossi sullo sfondo di un complesso scenario intellettuale. A questi testi si è affiancata la raccolta delle ricerche universitarie, degli articoli pubblicati su riviste specializzate e degli interventi a dibattiti e seminari. A proposito de L’architettura della città si è raccolta un’ampia letteratura critica riferita sia al testo in specifico che ad una sua collocazione nella storia dell’architettura, mettendo in discussione alcune osservazioni che pongono L’architettura della città come un libro risolutivo e definitivo. Per quanto riguarda il capitolo sulla teoria della permanenza l’analisi è stata svolta a partire dai testi che Rossi stesso indicava ne L’architettura della città rivelando i diversi apporti della letteratura urbanistica francese, e permettendo alla ricerca di precisare le relazioni con alcuni scritti centrali e al contempo colti da Rossi come opportunità per intraprendere l’elaborazione dell’idea di tipo. Per quest’ultima parte si può precisare come Rossi formuli la sua idea di tipo in un contesto culturale dove l’interesse per questo tema era fondamentale. Dunque le fonti che hanno assunto maggior rilievo in quest’ultima fase emergono da un ricco panorama in cui Rossi compie diverse ricerche sia con il gruppo redazionale di Casabella-continuità, sia all’interno della scuola veneziana negli anni Sessanta, ma anche negli studi per l’ILSES e per l’Istituto Nazionale d’Urbanistica. RESEARCH ON THE NOTION OF URBAN ARTIFACT IN THE ARCHITECTURE OF THE CITY BY ALDO ROSSI. Doctoral candidate: Letizia Biondi Tutor: Valter Balducci The present doctoral dissertation deals with the notion of urban artifact that was formulated and presented by Aldo Rossi in his book The Architecture of the City, published in 1966. In The Architecture of the City, the notion of urban artifact is enunciated through a wide range of definitions and forms. In this thesis, a research was done on how the construction of this concept over time was preceded by various studies started in 1953 during the author’s youth, then re-organized and synthesized since 1963 in a manuscript titled “Manual of urban planning” and in two more manuscripts later on. The work of research re-constructed the formulation of the notion of urban artifact through Rossi’s writings. In this sense, the examination of Rossi’s participation in debates, seminars, reviews, university courses or academic researches was of fundamental importance to understand the complexity of a work which is not to be attributed to disciplinary concepts, but to the formulation of a communicable theory. The effort to understand and to explain the notion of urban artifact led to an examination of the meaning used by Rossi to compose The Architecture of the City, which he defines as similar to a treatise. Through this analysis, it emerged that the composition of the book is not directly ascribable to the classical use of editorial writing of a treatise, whose most famous references in the past are the promotion of a correct practice as in the case of Vitruvio’s treatise, or the use of a structure that introduces a new category as in the Alberti case. Contrary to the two founding books, the lack of a global and prescriptive system and the not immediate reference to the writing of a classical treatise are evident in The Architecture of the City. However, the possibility of researching on some unpublished documents allowed to discover that in the writings starting from 1953 the analysis of the questions that are at the core of the notion of urban artifact is rich of intuitions, that aim to autonomy and that would be synthesized, even though not in a systematic way, in his famous book. The attempt was that of highlighting the specification over time of the notion of urban artifact and its elaboration in the various writings preceding the publication of The Architecture of the City. It was also specified that, despite building on theoretical grounds, Rossi indicates a progressive version of the notion of urban artifact, that is a performing use in the city. The present research aims to understand the cultural roots of the notion of urban artifact in two main directions: analyzing, firstly, Rossi’s interests along his formation path and, secondly, the definition of material structure of an urban artifact identified by Rossi in the permanences and enriched by various contributions from other disciplines. The purpose of the present research is to revise the formation path made by Rossi in a critical way, starting by 1953, underlining its innovative aspects and identifying its describing limits, which will never lead to the formulation of an exact notion, but rather to the elaboration of a complex synthesis, enriched by references to other studies. In brief, the thesis is composed of three parts: 1. The first part, titled “The Theory of urban artifacts in The Architecture of the City”, analyzes the concept of urban artifact in the more general theoretical context of the book The Architecture of the City. Such analysis is done by “disassembling” the book, and by linking together the argumentations and the multiplicity of the sources which are explicitly quoted by Rossi. In this context, the book’s structure is defined more precisely through the revision of the references used by Rossi to compose his theoretical project. Moreover, the author’s life is traced back through the various editions, re-printings, introductions and illustrations. Finally, it is specified which role the concept of urban artifact has in the book, pointing out that it is placed in an equal relation with the book’s title; by so doing, the concept of urban artifact gets the new meaning of “fact to be observed”, similar to the use that was suggested by the French urban geography at the beginning of the 20th century. 2. The second part, titled “The formation of the notion of urban artifact 1953-66”, introduces the theoretical elaboration in Rossi’s writings before The Architecture of the City, that is from 1953 to 1966. This part tries to describe Rossi’s cultural roots, his collaborations and his interests, tracing back the progressive definition of his conception of city over time. The analysis focuses on the path followed by Rossi and on the documents that he wrote since the years as a student at the Department of Architecture at the Politecnico in Milan. This leads to a complex scenario of first essays, articles and notes that bear witness to the intellectual research aiming to the construction of a knowledge on the background of the Realism of the 1950s. Rossi develops, in fact, a cultural engagement that leads him after his studies to deal with more general issues about the city. In particular, his important collaboration with the architecture magazine “Casabella-continuità”, with the director Ernesto Nathan Rogers and with the whole redaction staff mark the following period when he starts getting interested in city planning literature, art, sociology, geography, economics and philosophy. Since 1963, Rossi has worked with the group directed by Carlo Aymonino at the “Istituto Universitario di Architettura” (University Institute of Architecture) in Venice, especially researching on building typologies and urban morphology. During these years, Rossi elaborates an analytical synthesis for the formulation of a theory about the city. From the present research, it is evident that the writings preceding The Architecture of the City develop the studies on urban artifacts, which will become theoretical core of different chapters of the book. In conclusion, the genesis of the book is described; written in two years, what was conceived to be an “urban planning manual” became a “treatise draft” for the formulation of an urban science, as Rossi defines it. 3. The third part is titled “The material structure of urban artifacts: the theory of permanence”. This research is made on the study of the city as a material fact, a manufacture, whose construction was made over time, bearing the traces of time. As far as the topic of permanence is concerned, it was also important to draw a comparison with the debate about the issues of environmental pre-existence of re-construction in historical areas, which was very lively during the years of the Reconstruction. Right from the beginning, of fundamental importance were the relationship with Ernesto Nathan Rogers, the discussions on the pages of Casabella-Continuità and the participation to some debates and researches. It is to note that various terms were taken by the philosophical thesis by some personalities such as Antonio Banfi and Enzo Paci, and then re-elaborated by the redaction staff at Casabella-Continuità, which Rossi took part in as well. Through this analysis, it emerged that there were some shifts in meaning and the formulation of a vocabulary of terms within the complex area of the architectonic culture in the 1950s and 1960s. Then, I examined the shapes in which Rossi introduces the definition of the theory of permanence and the references by some authors for the scientific construction of an architecture theory whose aim is being communicable and offering concrete research tools. Such analysis allowed making a hypothesis about the significance for Rossi of the French geographers of the first half of the 20th century: in particular, the work by Marcel Poëte and by Pierre Lavedan is the main source and the research area which Rossi mostly explored to define the theory of permanence and monuments. Therefore, in The Architecture of the City, permanencies are not presented as the “whole”, but they emerge from a method which isolates permanent urban artifacts, in this way allowing making a hypothesis on “what remains” after the continuous transformations made in the city. The sources examined were quoted by Rossi in The Architecture of the City; in particular I analyzed them in the same edition which Rossi referred to. Through such an analysis, it was possible to make a comparison of the texts with one another, which let emerge the use of terms taken by languages belonging to other disciplines in The Architecture of the City and which the use of wholly extrapolated concepts is. Methodological premises As far as the formulation of the notion of urban artifact is concerned, the analysis focuses on the originality of the expression, the connections that are assumed or contained in Rossi’s writings about the city, by collecting direct and indirect sources which formed a significant corpus of writings. The most relevant direct sources were found in the special collections of the Getty Research Institute in Los Angeles, where the “Aldo Rossi Papers” are conserved. This archive contains unpublished material from 1954 to 1988, such as manuscripts, typescripts, notebooks, cyclostyled documents, scraps and notes, and several letters. In the Aldo Rossi Papers there are also 32 out of the 47 Light Blue Notebooks (Quaderni Azzurri), the rough drafts of The Architecture of the City and of the “A Scientific Autobiography”. As regards The Architecture of the City in particular, the Aldo Rossi Papers preserve: a notebook by the title of “Urban planning manual, June, 1963”, which is an explicit first draft of the book; “Notes for urban planning book summer/winter 1963”; a notebook with a red cover dated September 20th, 1964 – August 8th, 1965; and a notebook with a blue cover dated August 30th, 1965 – December 15th, 1965. The possibility of accessing this archive allowed to increase the bibliography related to the youth studies, enabling a revision of the cultural path followed by Rossi’s education. To that end, it was fundamental to re-evaluate some issues linked to the socialist realism which led to a more precise picture of the first writings by Rossi against the background of the intellectual scenario where he formed. In addition to these texts, the collection of university researches, the articles published on specialized reviews and the speeches at debates and seminars were also examined. About The Architecture of the City, a wide-ranging critical literature was collected, related both to the text specifics and to its collocation in the story of architecture, questioning some observations which define The Architecture of the City as a conclusive and definite book. As far as the chapter on the permanence theory is concerned, the analysis started by the texts that Rossi indicated in The Architecture of the City, revealing the different contributions from the French literature on urban planning. This allowed to the present research a more specific definition of the connections to some central writings which, at the same time, were seen by Rossi as an opportunity to start up the elaboration of the idea of type. For this last part, it can be specified that Rossi formulates his idea of type in a cultural context where the interest in this topic was fundamental. Therefore, the sources which played a central role in this final phase emerge from an extensive panorama in which Rossi researched not only with the redaction staff at Casablanca-continuità and within the School of Venice in the 1960s, but also in his studies for the ILSES (Institute of the Region Lombardia for Economics and Social Studies) and for the National Institute of Urban Planning.

Innovative analytical methods for Central Nervous System Drug analysis in biological fluids

During recent years a consistent number of central nervous system (CNS) drugs have been approved and introduced on the market for the treatment of many psychiatric and neurological disorders, including psychosis, depression, Parkinson disease and epilepsy. Despite the great advancements obtained in the treatment of CNS diseases/disorders, partial response to therapy or treatment failure are frequent, at least in part due to poor compliance, but also genetic variability in the metabolism of psychotropic agents or polypharmacy, which may lead to sub-therapeutic or toxic plasma levels of the drugs, and finally inefficacy of the treatment or adverse/toxic effects. With the aim of improving the treatment, reducing toxic/side effects and patient hospitalisation, Therapeutic Drug Monitoring (TDM) is certainly useful, allowing for a personalisation of the therapy. Reliable analytical methods are required to determine the plasma levels of psychotropic drugs, which are often present at low concentrations (tens or hundreds of nanograms per millilitre). The present PhD Thesis has focused on the development of analytical methods for the determination of CNS drugs in biological fluids, including antidepressants (sertraline and duloxetine), antipsychotics (aripiprazole), antiepileptics (vigabatrin and topiramate) and antiparkinsons (pramipexole). Innovative methods based on liquid chromatography or capillary electrophoresis coupled to diode-array or laser-induced fluorescence detectors have been developed, together with the suitable sample pre-treatment for interference removal and fluorescent labelling in case of LIF detection. All methods have been validated according to official guidelines and applied to the analysis of real samples obtained from patients, resulting suitable for the TDM of psychotropic drugs.

Studio e sviluppo di sistemi RFID in banda UHF

The recent widespread diffusion of radio-frequency identification (RFID) applications operating in the UHF band has been supported by both the request for greater interrogation ranges and greater and faster data exchange. UHF-RFID systems, exploiting a physical interaction based on Electromagnetic propagation, introduce many problems that have not been fully explored for the previous generations of RFID systems (e.g. HF). Therefore, the availability of reliable tools for modeling and evaluating the radio-communication between Reader and Tag within an RFID radio-link are needed. The first part of the thesis discuss the impact of real environment on system performance. In particular an analytical closed form formulation for the back-scattered field from the Tag antenna and the formulation for the lower bound of the BER achievable at the Reader side will be presented, considering different possible electromagnetic impairments. By means of the previous formulations, of the analysis of the RFID link operating in near filed conditions and of some electromagnetic/system-level co-simulations, an in-depth study of the dimensioning parameters and the actual performance of the systems will be discussed and analyzed, showing some relevant properties and trade-offs in transponder and reader design. Moreover a new low cost approach to extend the read range of the RFID UHF passive systems will be discussed. Within the scope to check the reliability of the analysis approaches and of innovative proposals, some reference transponder antennas have been designed and extensive measurement campaign has been carried out with satisfactory results. Finally, some commercial ad-hoc transponder for industrial application have been designed within the cooperation with Datalogic s.p.a., some guidelines and results will be briefly presented.

Numerical and analytical vibro-acoustic modelling of porous materials: the Cell Method for poroelasticity and the case of inclusions

Porous materials are widely used in many fields of industrial applications, to achieve the requirements of noise reduction, that nowadays derive from strict regulations. The modeling of porous materials is still a problematic issue. Numerical simulations are often problematic in case of real complex geometries, especially in terms of computational times and convergence. At the same time, analytical models, even if partly limited by restrictive simplificative hypotheses, represent a powerful instrument to capture quickly the physics of the problem and general trends. In this context, a recently developed numerical method, called the Cell Method, is described, is presented in the case of the Biot's theory and applied for representative cases. The peculiarity of the Cell Method is that it allows for a direct algebraic and geometrical discretization of the field equations, without any reduction to a weak integral form. Then, the second part of the thesis presents the case of interaction between two poroelastic materials under the context of double porosity. The idea of using periodically repeated inclusions of a second porous material into a layer composed by an original material is described. In particular, the problem is addressed considering the efficiency of the analytical method. A analytical procedure for the simulation of heterogeneous layers based is described and validated considering both conditions of absorption and transmission; a comparison with the available numerical methods is performed. ---------------- I materiali porosi sono ampiamente utilizzati per diverse applicazioni industriali, al fine di raggiungere gli obiettivi di riduzione del rumore, che sono resi impegnativi da norme al giorno d'oggi sempre più stringenti. La modellazione dei materiali porori per applicazioni vibro-acustiche rapprensenta un aspetto di una certa complessità. Le simulazioni numeriche sono spesso problematiche quando siano coinvolte geometrie di pezzi reali, in particolare riguardo i tempi computazionali e la convergenza. Allo stesso tempo, i modelli analitici, anche se parzialmente limitati a causa di ipotesi semplificative che ne restringono l'ambito di utilizzo, rappresentano uno strumento molto utile per comprendere rapidamente la fisica del problema e individuare tendenze generali. In questo contesto, un metodo numerico recentemente sviluppato, il Metodo delle Celle, viene descritto, implementato nel caso della teoria di Biot per la poroelasticità e applicato a casi rappresentativi. La peculiarità del Metodo delle Celle consiste nella discretizzazione diretta algebrica e geometrica delle equazioni di campo, senza alcuna riduzione a forme integrali deboli. Successivamente, nella seconda parte della tesi viene presentato il caso delle interazioni tra due materiali poroelastici a contatto, nel contesto dei materiali a doppia porosità. Viene descritta l'idea di utilizzare inclusioni periodicamente ripetute di un secondo materiale poroso all'interno di un layer a sua volta poroso. In particolare, il problema è studiando il metodo analitico e la sua efficienza. Una procedura analitica per il calcolo di strati eterogenei di materiale viene descritta e validata considerando sia condizioni di assorbimento, sia di trasmissione; viene effettuata una comparazione con i metodi numerici a disposizione.

Modellazione multibody di veicoli ferroviari: sviluppo ed implementazione di modelli innovativi per l'analisi del contatto ruota - rotaia

The wheel - rail contact analysis plays a fundamental role in the multibody modeling of railway vehicles. A good contact model must provide an accurate description of the global contact phenomena (contact forces and torques, number and position of the contact points) and of the local contact phenomena (position and shape of the contact patch, stresses and displacements). The model has also to assure high numerical efficiency (in order to be implemented directly online within multibody models) and a good compatibility with commercial multibody software (Simpack Rail, Adams Rail). The wheel - rail contact problem has been discussed by several authors and many models can be found in the literature. The contact models can be subdivided into two different categories: the global models and the local (or differential) models. Currently, as regards the global models, the main approaches to the problem are the so - called rigid contact formulation and the semi – elastic contact description. The rigid approach considers the wheel and the rail as rigid bodies. The contact is imposed by means of constraint equations and the contact points are detected during the dynamic simulation by solving the nonlinear algebraic differential equations associated to the constrained multibody system. Indentation between the bodies is not permitted and the normal contact forces are calculated through the Lagrange multipliers. Finally the Hertz’s and the Kalker’s theories allow to evaluate the shape of the contact patch and the tangential forces respectively. Also the semi - elastic approach considers the wheel and the rail as rigid bodies. However in this case no kinematic constraints are imposed and the indentation between the bodies is permitted. The contact points are detected by means of approximated procedures (based on look - up tables and simplifying hypotheses on the problem geometry). The normal contact forces are calculated as a function of the indentation while, as in the rigid approach, the Hertz’s and the Kalker’s theories allow to evaluate the shape of the contact patch and the tangential forces. Both the described multibody approaches are computationally very efficient but their generality and accuracy turn out to be often insufficient because the physical hypotheses behind these theories are too restrictive and, in many circumstances, unverified. In order to obtain a complete description of the contact phenomena, local (or differential) contact models are needed. In other words wheel and rail have to be considered elastic bodies governed by the Navier’s equations and the contact has to be described by suitable analytical contact conditions. The contact between elastic bodies has been widely studied in literature both in the general case and in the rolling case. Many procedures based on variational inequalities, FEM techniques and convex optimization have been developed. This kind of approach assures high generality and accuracy but still needs very large computational costs and memory consumption. Due to the high computational load and memory consumption, referring to the current state of the art, the integration between multibody and differential modeling is almost absent in literature especially in the railway field. However this integration is very important because only the differential modeling allows an accurate analysis of the contact problem (in terms of contact forces and torques, position and shape of the contact patch, stresses and displacements) while the multibody modeling is the standard in the study of the railway dynamics. In this thesis some innovative wheel – rail contact models developed during the Ph. D. activity will be described. Concerning the global models, two new models belonging to the semi – elastic approach will be presented; the models satisfy the following specifics: 1) the models have to be 3D and to consider all the six relative degrees of freedom between wheel and rail 2) the models have to consider generic railway tracks and generic wheel and rail profiles 3) the models have to assure a general and accurate handling of the multiple contact without simplifying hypotheses on the problem geometry; in particular the models have to evaluate the number and the position of the contact points and, for each point, the contact forces and torques 4) the models have to be implementable directly online within the multibody models without look - up tables 5) the models have to assure computation times comparable with those of commercial multibody software (Simpack Rail, Adams Rail) and compatible with RT and HIL applications 6) the models have to be compatible with commercial multibody software (Simpack Rail, Adams Rail). The most innovative aspect of the new global contact models regards the detection of the contact points. In particular both the models aim to reduce the algebraic problem dimension by means of suitable analytical techniques. This kind of reduction allows to obtain an high numerical efficiency that makes possible the online implementation of the new procedure and the achievement of performance comparable with those of commercial multibody software. At the same time the analytical approach assures high accuracy and generality. Concerning the local (or differential) contact models, one new model satisfying the following specifics will be presented: 1) the model has to be 3D and to consider all the six relative degrees of freedom between wheel and rail 2) the model has to consider generic railway tracks and generic wheel and rail profiles 3) the model has to assure a general and accurate handling of the multiple contact without simplifying hypotheses on the problem geometry; in particular the model has to able to calculate both the global contact variables (contact forces and torques) and the local contact variables (position and shape of the contact patch, stresses and displacements) 4) the model has to be implementable directly online within the multibody models 5) the model has to assure high numerical efficiency and a reduced memory consumption in order to achieve a good integration between multibody and differential modeling (the base for the local contact models) 6) the model has to be compatible with commercial multibody software (Simpack Rail, Adams Rail). In this case the most innovative aspects of the new local contact model regard the contact modeling (by means of suitable analytical conditions) and the implementation of the numerical algorithms needed to solve the discrete problem arising from the discretization of the original continuum problem. Moreover, during the development of the local model, the achievement of a good compromise between accuracy and efficiency turned out to be very important to obtain a good integration between multibody and differential modeling. At this point the contact models has been inserted within a 3D multibody model of a railway vehicle to obtain a complete model of the wagon. The railway vehicle chosen as benchmark is the Manchester Wagon the physical and geometrical characteristics of which are easily available in the literature. The model of the whole railway vehicle (multibody model and contact model) has been implemented in the Matlab/Simulink environment. The multibody model has been implemented in SimMechanics, a Matlab toolbox specifically designed for multibody dynamics, while, as regards the contact models, the CS – functions have been used; this particular Matlab architecture allows to efficiently connect the Matlab/Simulink and the C/C++ environment. The 3D multibody model of the same vehicle (this time equipped with a standard contact model based on the semi - elastic approach) has been then implemented also in Simpack Rail, a commercial multibody software for railway vehicles widely tested and validated. Finally numerical simulations of the vehicle dynamics have been carried out on many different railway tracks with the aim of evaluating the performances of the whole model. The comparison between the results obtained by the Matlab/ Simulink model and those obtained by the Simpack Rail model has allowed an accurate and reliable validation of the new contact models. In conclusion to this brief introduction to my Ph. D. thesis, we would like to thank Trenitalia and the Regione Toscana for the support provided during all the Ph. D. activity. Moreover we would also like to thank the INTEC GmbH, the society the develops the software Simpack Rail, with which we are currently working together to develop innovative toolboxes specifically designed for the wheel rail contact analysis.

Development of original analytical methods for the therapeutic drug monitoring of CNS druges: Antipsychotics, Antidepressants and Anxiolytics-hypnotics

Great strides have been made in the last few years in the pharmacological treatment of neuropsychiatric disorders, with the introduction into the therapy of several new and more efficient agents, which have improved the quality of life of many patients. Despite these advances, a large percentage of patients is still considered “non-responder” to the therapy, not drawing any benefits from it. Moreover, these patients have a peculiar therapeutic profile, due to the very frequent application of polypharmacy, attempting to obtain satisfactory remission of the multiple aspects of psychiatric syndromes. Therapy is heavily individualised and switching from one therapeutic agent to another is quite frequent. One of the main problems of this situation is the possibility of unwanted or unexpected pharmacological interactions, which can occur both during polypharmacy and during switching. Simultaneous administration of psychiatric drugs can easily lead to interactions if one of the administered compounds influences the metabolism of the others. Impaired CYP450 function due to inhibition of the enzyme is frequent. Other metabolic pathways, such as glucuronidation, can also be influenced. The Therapeutic Drug Monitoring (TDM) of psychotropic drugs is an important tool for treatment personalisation and optimisation. It deals with the determination of parent drugs and metabolites plasma levels, in order to monitor them over time and to compare these findings with clinical data. This allows establishing chemical-clinical correlations (such as those between administered dose and therapeutic and side effects), which are essential to obtain the maximum therapeutic efficacy, while minimising side and toxic effects. It is evident the importance of developing sensitive and selective analytical methods for the determination of the administered drugs and their main metabolites, in order to obtain reliable data that can correctly support clinical decisions. During the three years of Ph.D. program, some analytical methods based on HPLC have been developed, validated and successfully applied to the TDM of psychiatric patients undergoing treatment with drugs belonging to following classes: antipsychotics, antidepressants and anxiolytic-hypnotics. The biological matrices which have been processed were: blood, plasma, serum, saliva, urine, hair and rat brain. Among antipsychotics, both atypical and classical agents have been considered, such as haloperidol, chlorpromazine, clotiapine, loxapine, risperidone (and 9-hydroxyrisperidone), clozapine (as well as N-desmethylclozapine and clozapine N-oxide) and quetiapine. While the need for an accurate TDM of schizophrenic patients is being increasingly recognized by psychiatrists, only in the last few years the same attention is being paid to the TDM of depressed patients. This is leading to the acknowledgment that depression pharmacotherapy can greatly benefit from the accurate application of TDM. For this reason, the research activity has also been focused on first and second-generation antidepressant agents, like triciclic antidepressants, trazodone and m-chlorophenylpiperazine (m-cpp), paroxetine and its three main metabolites, venlafaxine and its active metabolite, and the most recent antidepressant introduced into the market, duloxetine. Among anxiolytics-hypnotics, benzodiazepines are very often involved in the pharmacotherapy of depression for the relief of anxious components; for this reason, it is useful to monitor these drugs, especially in cases of polypharmacy. The results obtained during these three years of Ph.D. program are reliable and the developed HPLC methods are suitable for the qualitative and quantitative determination of CNS drugs in biological fluids for TDM purposes.

Development of muliplexed analytical methods based on bioluminescent whole-cell biosensors

The subject of this Ph.D. research thesis is the development and application of multiplexed analytical methods based on bioluminescent whole-cell biosensors. One of the main goals of analytical chemistry is multianalyte testing in which two or more analytes are measured simultaneously in a single assay. The advantages of multianalyte testing are work simplification, high throughput, and reduction in the overall cost per test. The availability of multiplexed portable analytical systems is of particular interest for on-field analysis of clinical, environmental or food samples as well as for the drug discovery process. To allow highly sensitive and selective analysis, these devices should combine biospecific molecular recognition with ultrasensitive detection systems. To address the current need for rapid, highly sensitive and inexpensive devices for obtaining more data from each sample,genetically engineered whole-cell biosensors as biospecific recognition element were combined with ultrasensitive bioluminescence detection techniques. Genetically engineered cell-based sensing systems were obtained by introducing into bacterial, yeast or mammalian cells a vector expressing a reporter protein whose expression is controlled by regulatory proteins and promoter sequences. The regulatory protein is able to recognize the presence of the analyte (e.g., compounds with hormone-like activity, heavy metals…) and to consequently activate the expression of the reporter protein that can be readily measured and directly related to the analyte bioavailable concentration in the sample. Bioluminescence represents the ideal detection principle for miniaturized analytical devices and multiplexed assays thanks to high detectability in small sample volumes allowing an accurate signal localization and quantification. In the first chapter of this dissertation is discussed the obtainment of improved bioluminescent proteins emitting at different wavelenghts, in term of increased thermostability, enhanced emission decay kinetic and spectral resolution. The second chapter is mainly focused on the use of these proteins in the development of whole-cell based assay with improved analytical performance. In particular since the main drawback of whole-cell biosensors is the high variability of their analyte specific response mainly caused by variations in cell viability due to aspecific effects of the sample’s matrix, an additional bioluminescent reporter has been introduced to correct the analytical response thus increasing the robustness of the bioassays. The feasibility of using a combination of two or more bioluminescent proteins for obtaining biosensors with internal signal correction or for the simultaneous detection of multiple analytes has been demonstrated by developing a dual reporter yeast based biosensor for androgenic activity measurement and a triple reporter mammalian cell-based biosensor for the simultaneous monitoring of two CYP450 enzymes activation, involved in cholesterol degradation, with the use of two spectrally resolved intracellular luciferases and a secreted luciferase as a control for cells viability. In the third chapter is presented the development of a portable multianalyte detection system. In order to develop a portable system that can be used also outside the laboratory environment even by non skilled personnel, cells have been immobilized into a new biocompatible and transparent polymeric matrix within a modified clear bottom black 384 -well microtiter plate to obtain a bioluminescent cell array. The cell array was placed in contact with a portable charge-coupled device (CCD) light sensor able to localize and quantify the luminescent signal produced by different bioluminescent whole-cell biosensors. This multiplexed biosensing platform containing whole-cell biosensors was successfully used to measure the overall toxicity of a given sample as well as to obtain dose response curves for heavy metals and to detect hormonal activity in clinical samples (PCT/IB2010/050625: “Portable device based on immobilized cells for the detection of analytes.” Michelini E, Roda A, Dolci LS, Mezzanotte L, Cevenini L , 2010). At the end of the dissertation some future development steps are also discussed in order to develop a point of care (POCT) device that combine portability, minimum sample pre-treatment and highly sensitive multiplexed assays in a short assay time. In this POCT perspective, field-flow fractionation (FFF) techniques, in particular gravitational variant (GrFFF) that exploit the earth gravitational field to structure the separation, have been investigated for cells fractionation, characterization and isolation. Thanks to the simplicity of its equipment, amenable to miniaturization, the GrFFF techniques appears to be particularly suited for its implementation in POCT devices and may be used as pre-analytical integrated module to be applied directly to drive target analytes of raw samples to the modules where biospecifc recognition reactions based on ultrasensitive bioluminescence detection occurs, providing an increase in overall analytical output.