CMoS lab-on-a-chip devices for individual cell biology

The development of microlectronic lab-on-a-chip devices (LOACs) can now be pursued thanks to the continous advances in silicon technology. LOACs are miniaturized devices whose aim is to perform in a more efficient way specific chemical or biological analysis protocols which are usually carried out with traditional laboratory equipment. In this application area, CMOS technology has the potential to integrate LOAC functionalities for cell biology applications in single chips, e.g. sensors, actuators, signal conditioning and processing circuits. In this work, after a review of the state of the art, the development of a CMOS prototype chip for individual cell manipulation and detection based on dielectrophoresis will be presented. Issues related to the embedded optical and capacitive detection of cells will be discussed together with the main experimental results obtained in manipulation and detection of living cells and microparticles.

Tecniche per il controllo dinamico del consumo di potenza per piattaforme system-on-chip

Providing support for multimedia applications on low-power mobile devices remains a significant research challenge. This is primarily due to two reasons: • Portable mobile devices have modest sizes and weights, and therefore inadequate resources, low CPU processing power, reduced display capabilities, limited memory and battery lifetimes as compared to desktop and laptop systems. • On the other hand, multimedia applications tend to have distinctive QoS and processing requirementswhichmake themextremely resource-demanding. This innate conflict introduces key research challenges in the design of multimedia applications and device-level power optimization. Energy efficiency in this kind of platforms can be achieved only via a synergistic hardware and software approach. In fact, while System-on-Chips are more and more programmable thus providing functional flexibility, hardwareonly power reduction techniques cannot maintain consumption under acceptable bounds. It is well understood both in research and industry that system configuration andmanagement cannot be controlled efficiently only relying on low-level firmware and hardware drivers. In fact, at this level there is lack of information about user application activity and consequently about the impact of power management decision on QoS. Even though operating system support and integration is a requirement for effective performance and energy management, more effective and QoSsensitive power management is possible if power awareness and hardware configuration control strategies are tightly integratedwith domain-specificmiddleware services. The main objective of this PhD research has been the exploration and the integration of amiddleware-centric energymanagement with applications and operating-system. We choose to focus on the CPU-memory and the video subsystems, since they are the most power-hungry components of an embedded system. A second main objective has been the definition and implementation of software facilities (like toolkits, API, and run-time engines) in order to improve programmability and performance efficiency of such platforms. Enhancing energy efficiency and programmability ofmodernMulti-Processor System-on-Chips (MPSoCs) Consumer applications are characterized by tight time-to-market constraints and extreme cost sensitivity. The software that runs on modern embedded systems must be high performance, real time, and even more important low power. Although much progress has been made on these problems, much remains to be done. Multi-processor System-on-Chip (MPSoC) are increasingly popular platforms for high performance embedded applications. This leads to interesting challenges in software development since efficient software development is a major issue for MPSoc designers. An important step in deploying applications on multiprocessors is to allocate and schedule concurrent tasks to the processing and communication resources of the platform. The problem of allocating and scheduling precedenceconstrained tasks on processors in a distributed real-time system is NP-hard. There is a clear need for deployment technology that addresses thesemulti processing issues. This problem can be tackled by means of specific middleware which takes care of allocating and scheduling tasks on the different processing elements and which tries also to optimize the power consumption of the entire multiprocessor platform. This dissertation is an attempt to develop insight into efficient, flexible and optimalmethods for allocating and scheduling concurrent applications tomultiprocessor architectures. It is a well-known problem in literature: this kind of optimization problems are very complex even in much simplified variants, therefore most authors propose simplified models and heuristic approaches to solve it in reasonable time. Model simplification is often achieved by abstracting away platform implementation ”details”. As a result, optimization problems become more tractable, even reaching polynomial time complexity. Unfortunately, this approach creates an abstraction gap between the optimization model and the real HW-SW platform. The main issue with heuristic or, more in general, with incomplete search is that they introduce an optimality gap of unknown size. They provide very limited or no information on the distance between the best computed solution and the optimal one. The goal of this work is to address both abstraction and optimality gaps, formulating accurate models which accounts for a number of ”non-idealities” in real-life hardware platforms, developing novel mapping algorithms that deterministically find optimal solutions, and implementing software infrastructures required by developers to deploy applications for the targetMPSoC platforms. Energy Efficient LCDBacklightAutoregulation on Real-LifeMultimediaAp- plication Processor Despite the ever increasing advances in Liquid Crystal Display’s (LCD) technology, their power consumption is still one of the major limitations to the battery life of mobile appliances such as smart phones, portable media players, gaming and navigation devices. There is a clear trend towards the increase of LCD size to exploit the multimedia capabilities of portable devices that can receive and render high definition video and pictures. Multimedia applications running on these devices require LCD screen sizes of 2.2 to 3.5 inches andmore to display video sequences and pictures with the required quality. LCD power consumption is dependent on the backlight and pixel matrix driving circuits and is typically proportional to the panel area. As a result, the contribution is also likely to be considerable in future mobile appliances. To address this issue, companies are proposing low power technologies suitable for mobile applications supporting low power states and image control techniques. On the research side, several power saving schemes and algorithms can be found in literature. Some of them exploit software-only techniques to change the image content to reduce the power associated with the crystal polarization, some others are aimed at decreasing the backlight level while compensating the luminance reduction by compensating the user perceived quality degradation using pixel-by-pixel image processing algorithms. The major limitation of these techniques is that they rely on the CPU to perform pixel-based manipulations and their impact on CPU utilization and power consumption has not been assessed. This PhDdissertation shows an alternative approach that exploits in a smart and efficient way the hardware image processing unit almost integrated in every current multimedia application processors to implement a hardware assisted image compensation that allows dynamic scaling of the backlight with a negligible impact on QoS. The proposed approach overcomes CPU-intensive techniques by saving system power without requiring either a dedicated display technology or hardware modification. Thesis Overview The remainder of the thesis is organized as follows. The first part is focused on enhancing energy efficiency and programmability of modern Multi-Processor System-on-Chips (MPSoCs). Chapter 2 gives an overview about architectural trends in embedded systems, illustrating the principal features of new technologies and the key challenges still open. Chapter 3 presents a QoS-driven methodology for optimal allocation and frequency selection for MPSoCs. The methodology is based on functional simulation and full system power estimation. Chapter 4 targets allocation and scheduling of pipelined stream-oriented applications on top of distributed memory architectures with messaging support. We tackled the complexity of the problem by means of decomposition and no-good generation, and prove the increased computational efficiency of this approach with respect to traditional ones. Chapter 5 presents a cooperative framework to solve the allocation, scheduling and voltage/frequency selection problem to optimality for energyefficient MPSoCs, while in Chapter 6 applications with conditional task graph are taken into account. Finally Chapter 7 proposes a complete framework, called Cellflow, to help programmers in efficient software implementation on a real architecture, the Cell Broadband Engine processor. The second part is focused on energy efficient software techniques for LCD displays. Chapter 8 gives an overview about portable device display technologies, illustrating the principal features of LCD video systems and the key challenges still open. Chapter 9 shows several energy efficient software techniques present in literature, while Chapter 10 illustrates in details our method for saving significant power in an LCD panel. Finally, conclusions are drawn, reporting the main research contributions that have been discussed throughout this dissertation.

Design and Performance Evaluation of Network-on-Chip Communication Protocols and Architectures

The scale down of transistor technology allows microelectronics manufacturers such as Intel and IBM to build always more sophisticated systems on a single microchip. The classical interconnection solutions based on shared buses or direct connections between the modules of the chip are becoming obsolete as they struggle to sustain the increasing tight bandwidth and latency constraints that these systems demand. The most promising solution for the future chip interconnects are the Networks on Chip (NoC). NoCs are network composed by routers and channels used to inter- connect the different components installed on the single microchip. Examples of advanced processors based on NoC interconnects are the IBM Cell processor, composed by eight CPUs that is installed on the Sony Playstation III and the Intel Teraflops pro ject composed by 80 independent (simple) microprocessors. On chip integration is becoming popular not only in the Chip Multi Processor (CMP) research area but also in the wider and more heterogeneous world of Systems on Chip (SoC). SoC comprehend all the electronic devices that surround us such as cell-phones, smart-phones, house embedded systems, automotive systems, set-top boxes etc... SoC manufacturers such as ST Microelectronics , Samsung, Philips and also Universities such as Bologna University, M.I.T., Berkeley and more are all proposing proprietary frameworks based on NoC interconnects. These frameworks help engineers in the switch of design methodology and speed up the development of new NoC-based systems on chip. In this Thesis we propose an introduction of CMP and SoC interconnection networks. Then focusing on SoC systems we propose: • a detailed analysis based on simulation of the Spidergon NoC, a ST Microelectronics solution for SoC interconnects. The Spidergon NoC differs from many classical solutions inherited from the parallel computing world. Here we propose a detailed analysis of this NoC topology and routing algorithms. Furthermore we propose aEqualized a new routing algorithm designed to optimize the use of the resources of the network while also increasing its performance; • a methodology flow based on modified publicly available tools that combined can be used to design, model and analyze any kind of System on Chip; • a detailed analysis of a ST Microelectronics-proprietary transport-level protocol that the author of this Thesis helped developing; • a simulation-based comprehensive comparison of different network interface designs proposed by the author and the researchers at AST lab, in order to integrate shared-memory and message-passing based components on a single System on Chip; • a powerful and flexible solution to address the time closure exception issue in the design of synchronous Networks on Chip. Our solution is based on relay stations repeaters and allows to reduce the power and area demands of NoC interconnects while also reducing its buffer needs; • a solution to simplify the design of the NoC by also increasing their performance and reducing their power and area consumption. We propose to replace complex and slow virtual channel-based routers with multiple and flexible small Multi Plane ones. This solution allows us to reduce the area and power dissipation of any NoC while also increasing its performance especially when the resources are reduced. This Thesis has been written in collaboration with the Advanced System Technology laboratory in Grenoble France, and the Computer Science Department at Columbia University in the city of New York.

Tecniche di ottimizzazione del software per sistemi su singolo chip per applicazioni di Nomadic Computing

I moderni sistemi embedded sono equipaggiati con risorse hardware che consentono l’esecuzione di applicazioni molto complesse come il decoding audio e video. La progettazione di simili sistemi deve soddisfare due esigenze opposte. Da un lato è necessario fornire un elevato potenziale computazionale, dall’altro bisogna rispettare dei vincoli stringenti riguardo il consumo di energia. Uno dei trend più diffusi per rispondere a queste esigenze opposte è quello di integrare su uno stesso chip un numero elevato di processori caratterizzati da un design semplificato e da bassi consumi. Tuttavia, per sfruttare effettivamente il potenziale computazionale offerto da una batteria di processoriè necessario rivisitare pesantemente le metodologie di sviluppo delle applicazioni. Con l’avvento dei sistemi multi-processore su singolo chip (MPSoC) il parallel programming si è diffuso largamente anche in ambito embedded. Tuttavia, i progressi nel campo della programmazione parallela non hanno mantenuto il passo con la capacità di integrare hardware parallelo su un singolo chip. Oltre all’introduzione di multipli processori, la necessità di ridurre i consumi degli MPSoC comporta altre soluzioni architetturali che hanno l’effetto diretto di complicare lo sviluppo delle applicazioni. Il design del sottosistema di memoria, in particolare, è un problema critico. Integrare sul chip dei banchi di memoria consente dei tempi d’accesso molto brevi e dei consumi molto contenuti. Sfortunatamente, la quantità di memoria on-chip che può essere integrata in un MPSoC è molto limitata. Per questo motivo è necessario aggiungere dei banchi di memoria off-chip, che hanno una capacità molto maggiore, come maggiori sono i consumi e i tempi d’accesso. La maggior parte degli MPSoC attualmente in commercio destina una parte del budget di area all’implementazione di memorie cache e/o scratchpad. Le scratchpad (SPM) sono spesso preferite alle cache nei sistemi MPSoC embedded, per motivi di maggiore predicibilità, minore occupazione d’area e – soprattutto – minori consumi. Per contro, mentre l’uso delle cache è completamente trasparente al programmatore, le SPM devono essere esplicitamente gestite dall’applicazione. Esporre l’organizzazione della gerarchia di memoria ll’applicazione consente di sfruttarne in maniera efficiente i vantaggi (ridotti tempi d’accesso e consumi). Per contro, per ottenere questi benefici è necessario scrivere le applicazioni in maniera tale che i dati vengano partizionati e allocati sulle varie memorie in maniera opportuna. L’onere di questo compito complesso ricade ovviamente sul programmatore. Questo scenario descrive bene l’esigenza di modelli di programmazione e strumenti di supporto che semplifichino lo sviluppo di applicazioni parallele. In questa tesi viene presentato un framework per lo sviluppo di software per MPSoC embedded basato su OpenMP. OpenMP è uno standard di fatto per la programmazione di multiprocessori con memoria shared, caratterizzato da un semplice approccio alla parallelizzazione tramite annotazioni (direttive per il compilatore). La sua interfaccia di programmazione consente di esprimere in maniera naturale e molto efficiente il parallelismo a livello di loop, molto diffuso tra le applicazioni embedded di tipo signal processing e multimedia. OpenMP costituisce un ottimo punto di partenza per la definizione di un modello di programmazione per MPSoC, soprattutto per la sua semplicità d’uso. D’altra parte, per sfruttare in maniera efficiente il potenziale computazionale di un MPSoC è necessario rivisitare profondamente l’implementazione del supporto OpenMP sia nel compilatore che nell’ambiente di supporto a runtime. Tutti i costrutti per gestire il parallelismo, la suddivisione del lavoro e la sincronizzazione inter-processore comportano un costo in termini di overhead che deve essere minimizzato per non comprometterre i vantaggi della parallelizzazione. Questo può essere ottenuto soltanto tramite una accurata analisi delle caratteristiche hardware e l’individuazione dei potenziali colli di bottiglia nell’architettura. Una implementazione del task management, della sincronizzazione a barriera e della condivisione dei dati che sfrutti efficientemente le risorse hardware consente di ottenere elevate performance e scalabilità. La condivisione dei dati, nel modello OpenMP, merita particolare attenzione. In un modello a memoria condivisa le strutture dati (array, matrici) accedute dal programma sono fisicamente allocate su una unica risorsa di memoria raggiungibile da tutti i processori. Al crescere del numero di processori in un sistema, l’accesso concorrente ad una singola risorsa di memoria costituisce un evidente collo di bottiglia. Per alleviare la pressione sulle memorie e sul sistema di connessione vengono da noi studiate e proposte delle tecniche di partizionamento delle strutture dati. Queste tecniche richiedono che una singola entità di tipo array venga trattata nel programma come l’insieme di tanti sotto-array, ciascuno dei quali può essere fisicamente allocato su una risorsa di memoria differente. Dal punto di vista del programma, indirizzare un array partizionato richiede che ad ogni accesso vengano eseguite delle istruzioni per ri-calcolare l’indirizzo fisico di destinazione. Questo è chiaramente un compito lungo, complesso e soggetto ad errori. Per questo motivo, le nostre tecniche di partizionamento sono state integrate nella l’interfaccia di programmazione di OpenMP, che è stata significativamente estesa. Specificamente, delle nuove direttive e clausole consentono al programmatore di annotare i dati di tipo array che si vuole partizionare e allocare in maniera distribuita sulla gerarchia di memoria. Sono stati inoltre sviluppati degli strumenti di supporto che consentono di raccogliere informazioni di profiling sul pattern di accesso agli array. Queste informazioni vengono sfruttate dal nostro compilatore per allocare le partizioni sulle varie risorse di memoria rispettando una relazione di affinità tra il task e i dati. Più precisamente, i passi di allocazione nel nostro compilatore assegnano una determinata partizione alla memoria scratchpad locale al processore che ospita il task che effettua il numero maggiore di accessi alla stessa.

Architetture di interconnessione per sistemi su singolo chip e per sistemi ad integrazione tridimensionale

I continui sviluppi nel campo della fabbricazione dei circuiti integrati hanno comportato frequenti travolgimenti nel design, nell’implementazione e nella scalabilità dei device elettronici, così come nel modo di utilizzarli. Anche se la legge di Moore ha anticipato e caratterizzato questo trend nelle ultime decadi, essa stessa si trova a fronteggiare attualmente enormi limitazioni, superabili solo attraverso un diverso approccio nella produzione di chip, consistente in pratica nella sovrapposizione verticale di diversi strati collegati elettricamente attraverso speciali vias. Sul singolo strato, le network on chip sono state suggerite per ovviare le profonde limitazioni dovute allo scaling di strutture di comunicazione condivise. Questa tesi si colloca principalmente nel contesto delle nascenti piattaforme multicore ad alte prestazioni basate sulle 3D NoC, in cui la network on chip viene estesa nelle 3 direzioni. L’obiettivo di questo lavoro è quello di fornire una serie di strumenti e tecniche per poter costruire e aratterizzare una piattaforma tridimensionale, cosi come dimostrato nella realizzazione del testchip 3D NOC fabbricato presso la fonderia IMEC. Il primo contributo è costituito sia una accurata caratterizzazione delle interconnessioni verticali (TSVs) (ovvero delle speciali vias che attraversano l’intero substrato del die), sia dalla caratterizzazione dei router 3D (in cui una o più porte sono estese nella direzione verticale) ed infine dal setup di un design flow 3D utilizzando interamente CAD 2D. Questo primo step ci ha permesso di effettuare delle analisi dettagliate sia sul costo sia sulle varie implicazioni. Il secondo contributo è costituito dallo sviluppo di alcuni blocchi funzionali necessari per garantire il corretto funziomento della 3D NoC, in presenza sia di guasti nelle TSVs (fault tolerant links) che di deriva termica nei vari clock tree dei vari die (alberi di clock indipendenti). Questo secondo contributo è costituito dallo sviluppo delle seguenti soluzioni circuitali: 3D fault tolerant link, Look Up Table riconfigurabili e un sicnronizzatore mesocrono. Il primo è costituito fondamentalmente un bus verticale equipaggiato con delle TSV di riserva da utilizzare per rimpiazzare le vias guaste, più la logica di controllo per effettuare il test e la riconfigurazione. Il secondo è rappresentato da una Look Up Table riconfigurabile, ad alte prestazioni e dal costo contenuto, necesaria per bilanciare sia il traffico nella NoC che per bypassare link non riparabili. Infine la terza soluzione circuitale è rappresentata da un sincronizzatore mesocrono necessario per garantire la sincronizzazione nel trasferimento dati da un layer and un altro nelle 3D Noc. Il terzo contributo di questa tesi è dato dalla realizzazione di un interfaccia multicore per memorie 3D (stacked 3D DRAM) ad alte prestazioni, e dall’esplorazione architetturale dei benefici e del costo di questo nuovo sistema in cui il la memoria principale non è piu il collo di bottiglia dell’intero sistema. Il quarto ed ultimo contributo è rappresentato dalla realizzazione di un 3D NoC test chip presso la fonderia IMEC, e di un circuito full custom per la caratterizzazione della variability dei parametri RC delle interconnessioni verticali.

Multi Processor Systems On Chip with Configurable Hardware Acceleration

The evolution of the electronics embedded applications forces electronics systems designers to match their ever increasing requirements. This evolution pushes the computational power of digital signal processing systems, as well as the energy required to accomplish the computations, due to the increasing mobility of such applications. Current approaches used to match these requirements relies on the adoption of application specific signal processors. Such kind of devices exploits powerful accelerators, which are able to match both performance and energy requirements. On the other hand, the too high specificity of such accelerators often results in a lack of flexibility which affects non-recurrent engineering costs, time to market, and market volumes too. The state of the art mainly proposes two solutions to overcome these issues with the ambition of delivering reasonable performance and energy efficiency: reconfigurable computing and multi-processors computing. All of these solutions benefits from the post-fabrication programmability, that definitively results in an increased flexibility. Nevertheless, the gap between these approaches and dedicated hardware is still too high for many application domains, especially when targeting the mobile world. In this scenario, flexible and energy efficient acceleration can be achieved by merging these two computational paradigms, in order to address all the above introduced constraints. This thesis focuses on the exploration of the design and application spectrum of reconfigurable computing, exploited as application specific accelerators for multi-processors systems on chip. More specifically, it introduces a reconfigurable digital signal processor featuring a heterogeneous set of reconfigurable engines, and a homogeneous multi-core system, exploiting three different flavours of reconfigurable and mask-programmable technologies as implementation platform for applications specific accelerators. In this work, the various trade-offs concerning the utilization multi-core platforms and the different configuration technologies are explored, characterizing the design space of the proposed approach in terms of programmability, performance, energy efficiency and manufacturing costs.

Model predictive control in thermal management of multiprocessor systems-on-chip

MultiProcessor Systems-on-Chip (MPSoC) are the core of nowadays and next generation computing platforms. Their relevance in the global market continuously increase, occupying an important role both in everydaylife products (e.g. smartphones, tablets, laptops, cars) and in strategical market sectors as aviation, defense, robotics, medicine. Despite of the incredible performance improvements in the recent years processors manufacturers have had to deal with issues, commonly called “Walls”, that have hindered the processors development. After the famous “Power Wall”, that limited the maximum frequency of a single core and marked the birth of the modern multiprocessors system-on-chip, the “Thermal Wall” and the “Utilization Wall” are the actual key limiter for performance improvements. The former concerns the damaging effects of the high temperature on the chip caused by the large power densities dissipation, whereas the second refers to the impossibility of fully exploiting the computing power of the processor due to the limitations on power and temperature budgets. In this thesis we faced these challenges by developing efficient and reliable solutions able to maximize performance while limiting the maximum temperature below a fixed critical threshold and saving energy. This has been possible by exploiting the Model Predictive Controller (MPC) paradigm that solves an optimization problem subject to constraints in order to find the optimal control decisions for the future interval. A fully-distributedMPC-based thermal controller with a far lower complexity respect to a centralized one has been developed. The control feasibility and interesting properties for the simplification of the control design has been proved by studying a partial differential equation thermal model. Finally, the controller has been efficiently included in more complex control schemes able to minimize energy consumption and deal with mixed-criticalities tasks

Parallel Architectures for Many-Core Systems-On-Chip in Deep Sub-Micron Technology

Despite the several issues faced in the past, the evolutionary trend of silicon has kept its constant pace. Today an ever increasing number of cores is integrated onto the same die. Unfortunately, the extraordinary performance achievable by the many-core paradigm is limited by several factors. Memory bandwidth limitation, combined with inefficient synchronization mechanisms, can severely overcome the potential computation capabilities. Moreover, the huge HW/SW design space requires accurate and flexible tools to perform architectural explorations and validation of design choices. In this thesis we focus on the aforementioned aspects: a flexible and accurate Virtual Platform has been developed, targeting a reference many-core architecture. Such tool has been used to perform architectural explorations, focusing on instruction caching architecture and hybrid HW/SW synchronization mechanism. Beside architectural implications, another issue of embedded systems is considered: energy efficiency. Near Threshold Computing is a key research area in the Ultra-Low-Power domain, as it promises a tenfold improvement in energy efficiency compared to super-threshold operation and it mitigates thermal bottlenecks. The physical implications of modern deep sub-micron technology are severely limiting performance and reliability of modern designs. Reliability becomes a major obstacle when operating in NTC, especially memory operation becomes unreliable and can compromise system correctness. In the present work a novel hybrid memory architecture is devised to overcome reliability issues and at the same time improve energy efficiency by means of aggressive voltage scaling when allowed by workload requirements. Variability is another great drawback of near-threshold operation. The greatly increased sensitivity to threshold voltage variations in today a major concern for electronic devices. We introduce a variation-tolerant extension of the baseline many-core architecture. By means of micro-architectural knobs and a lightweight runtime control unit, the baseline architecture becomes dynamically tolerant to variations.

Localizzazione della topoisomerasi IB sui telomeri di S. cerevisiae e ruolo della sua attività catalitica sulle modificazioni istoniche

Il superavvolgimento del DNA nelle cellule, regolato dalle DNA Topoisomerasi, influenza molti processi biologici, quali la trascrizione, la replicazione, la ricombinazione ed il rimodellamento della cromatina. La DNA Topoisomerasi IB eucariotica, (Top1), è un enzima efficiente nella rimozione dei superavvolgimenti del DNA in vitro e la sua principale funzione cellulare è la rimozione dei superavvolgimenti positivi e negativi generati durante la trascrizione e la replicazione. Risultati recenti hanno fornito evidenze sperimentali del coinvolgimento di Top1 in meccanismi multipli di regolazione dell’espressione genica eucariotica, in particolare nella fase di inizio e maturazione dei trascritti. Tuttavia, le funzioni di Top1 non sono ancora state stabilite a livello globale. Pertanto, nella presente tesi di dottorato abbiamo risposto a questa domanda con l’analisi dei profili di trascrizione genica globale e con studi di immunoprecipitazione della cromatina (ChIP) in cellule di S. cerevisiae. Circa il 9% dei geni sono influenzati da Top1, e l’analisi dei profili di espressione mostra che Top1 wt aumenta l’utilizzo del glucosio e dei pathway per la produzione di energia, con specifica diminuzione della trascrizione dei geni telomerici e subtelomerici. Abbiamo inoltre dimostrato che Top1 wt, ma non il suo mutante inattivo, aumenta la velocità di crescita cellulare nelle cellule di lievito studiate. Le analisi di ChIP mostrano che, in confronto all’assenza dell’enzima, Top1 wt diminuisce l’acetilazione dell’istone H4, compresa quella specifica della lisina 16, nel telomero destro del cromosoma XIV mentre la mutazione che inattiva l’enzima aumenta in maniera marcata l’acetilazione dell’istone H4 e la di-metilazione della lisina 4 dell’istone H3. Top1 wt incrementa anche il reclutamento di Sir3 nelle regioni di confine della cromatina silenziata dello stesso telomero. Studi di immunoprecipitazione indicano che l’enzima interagisce direttamente con la struttura della cromatina telomerica poichè entrambe le proteine, quella wt e quella inattiva, sono localizzate sulle ripetizioni telomeriche dei cromosomi di lievito. Questi risultati dimostrano che Top1, una proteina non essenziale in lievito, ottimizza i livelli globali dei trascritti per una crescita più efficiente di cellule in fase esponenziale. Indagando il meccanismo che è alla base della specifica repressione dei geni telomerici, abbiamo dimostrato che Top1 favorisce delle modifiche posttraduzionali degli istoni che indicano una struttura della cromatina repressa nelle regioni telomeriche.

New materials for electrochemiluminescence

The study of electrochemiluminescence (ECL) involves photophysical and electrochemical aspects. Excited states are populated by an electrical stimulus. The most important applications are in the diagnostic field where a number of different biologically-relevant molecules (e.g. proteins and nucleic acids) can be recognized and quantified with a sensitivity and specificity previously not reachable. As a matter of fact the electrochemistry, differently to the classic techniques as fluorescence and chemiluminescence, allows to control the excited state generation spatially and temporally. The two research visits into A. J. Bard electrochemistry laboratories were priceless. Dr. Bard has been one of ECL pioneers, the first to introduce the technique and the one who discovered in 1972 the surprising emission of Ru(bpy)3 2+. I consider necessary to thank by now my supervisors Massimo and Francesco for their help and for giving me the great opportunity to know this unique science man that made me feel enthusiastic. I will never be grateful enough… Considering that the experimental techniques of ECL did not changed significantly in these last years the most convenient research direction has been the developing of materials with new or improved properties. In Chapter I the basics concepts and mechanisms of ECL are introduced so that the successive experiments can be easily understood. In the final paragraph the scopes of the thesis are briefly described. In Chapter II by starting from ECL experimental apparatus of Dr. Bard’s laboratories the design, assembly and preliminary tests of the new Bologna instrument are carefully described. The instrument assembly required to work hard but resulted in the introduction of the new technique in our labs by allowing the continuation of the ECL studies began in Texas. In Chapter III are described the results of electrochemical and ECL studies performed on new synthesized Ru(II) complexes containing tetrazolate based ligands. ECL emission has been investigated in solution and in solid thin films. The effect of the chemical protonation of the tetrazolate ring on ECL emission has been also investigated evidencing the possibility of a catalytic effect (generation of molecular hydrogen) of one of the complexes in organic media. Finally, after a series of preliminary studies on ECL emission in acqueous buffers, the direct interaction with calf thymus DNA of some complexes has been tested by ECL and photoluminescence (PL) titration. In Chapter IV different Ir(III) complexes have been characterized electrochemically and photophysically (ECL and PL). Some complexes were already well-known in literature for their high quantum efficiency whereas the remaining were new synthesized compounds containing tetrazolate based ligands analogous to those investigated in Chapt. III. During the tests on a halogenated complex was unexpectedly evidenced the possibility to follow the kinetics of an electro-induced chemical reaction by using ECL signal. In the last chapter (V) the possibility to use mono-use silicon chips electrodes as ECL analitycal devices is under investigation. The chapter begins by describing the chip structure and materials then a signal reproducibility study and geometry optimization is carried on by using two different complexes. In the following paragraphs is reported in detail the synthesis of an ECL label based on Ru(bpy)3 2+ and the chip functionalization by using a lipoic acid SAM and the same label. After some preliminary characterizations (mass spectroscopy TOF) has been demonstrated that by mean of a simple and fast ECL measurement it’s possible to confirm the presence of the coupling product SAM-label into the chip with a very high sensitivity. No signal was detected from the same system by using photoluminescence.

Reduced-order modelling, circuit-level design and SOI fabrication of microelectromechanical resonators

This thesis deals with two important research aspects concerning radio frequency (RF) microresonators and switches. First, a new approach for compact modeling and simulation of these devices is presented. Then, a combined process flow for their simultaneous fabrication on a SOI substrate is proposed. Compact models for microresonators and switches are extracted by applying mathematical model order reduction (MOR) to the devices finite element (FE) description in ANSYS c° . The behaviour of these devices includes forms of nonlinearities. However, an approximation in the creation of the FE model is introduced, which enables the use of linear model order reduction. Microresonators are modeled with the introduction of transducer elements, which allow for direct coupling of the electrical and mechanical domain. The coupled system element matrices are linearized around an operating point and reduced. The resulting macromodel is valid for small signal analysis around the bias point, such as harmonic pre-stressed analysis. This is extremely useful for characterizing the frequency response of resonators. Compact modelling of switches preserves the nonlinearity of the device behaviour. Nonlinear reduced order models are obtained by reducing the number of nonlinearities in the system and handling them as input to the system. In this way, the system can be reduced using linear MOR techniques and nonlinearities are introduced directly in the reduced order model. The reduction of the number of system nonlinearities implies the approximation of all distributed forces in the model with lumped forces. Both for microresonators and switches, a procedure for matrices extraction has been developed so that reduced order models include the effects of electrical and mechanical pre-stress. The extraction process is fast and can be done automatically from ANSYS binary files. The method has been applied for the simulation of several devices both at devices and circuit level. Simulation results have been compared with full model simulations, and, when available, experimental data. Reduced order models have proven to conserve the accuracy of finite element method and to give a good description of the overall device behaviour, despite the introduced approximations. In addition, simulation is very fast, both at device and circuit level. A combined process-flow for the integrated fabrication of microresonators and switches has been defined. For this purpose, two processes that are optimized for the independent fabrication of these devices are merged. The major advantage of this process is the possibility to create on-chip circuit blocks that include both microresonators and switches. An application is, for example, aswitched filter bank for wireless transceiver. The process for microresonators fabrication is characterized by the use of silicon on insulator (SOI) wafers and on a deep reactive ion etching (DRIE) step for the creation of the vibrating structures in single-crystal silicon and the use of a sacrificial oxide layer for the definition of resonator to electrode distance. The fabrication of switches is characterized by the use of two different conductive layers for the definition of the actuation electrodes and by the use of a photoresist as a sacrificial layer for the creation of the suspended structure. Both processes have a gold electroplating step, for the creation of the resonators electrodes, transmission lines and suspended structures. The combined process flow is designed such that it conserves the basic properties of the original processes. Neither the performance of the resonators nor the performance of the switches results affected by the simultaneous fabrication. Moreover, common fabrication steps are shared, which allows for cheaper and faster fabrication.

Interconnection systems for highly integrated computation devices

The sustained demand for faster,more powerful chips has beenmet by the availability of chip manufacturing processes allowing for the integration of increasing numbers of computation units onto a single die. The resulting outcome, especially in the embedded domain, has often been called SYSTEM-ON-CHIP (SOC) or MULTI-PROCESSOR SYSTEM-ON-CHIP (MPSOC). MPSoC design brings to the foreground a large number of challenges, one of the most prominent of which is the design of the chip interconnection. With a number of on-chip blocks presently ranging in the tens, and quickly approaching the hundreds, the novel issue of how to best provide on-chip communication resources is clearly felt. NETWORKS-ON-CHIPS (NOCS) are the most comprehensive and scalable answer to this design concern. By bringing large-scale networking concepts to the on-chip domain, they guarantee a structured answer to present and future communication requirements. The point-to-point connection and packet switching paradigms they involve are also of great help in minimizing wiring overhead and physical routing issues. However, as with any technology of recent inception, NoC design is still an evolving discipline. Several main areas of interest require deep investigation for NoCs to become viable solutions: • The design of the NoC architecture needs to strike the best tradeoff among performance, features and the tight area and power constraints of the on-chip domain. • Simulation and verification infrastructure must be put in place to explore, validate and optimize the NoC performance. • NoCs offer a huge design space, thanks to their extreme customizability in terms of topology and architectural parameters. Design tools are needed to prune this space and pick the best solutions. • Even more so given their global, distributed nature, it is essential to evaluate the physical implementation of NoCs to evaluate their suitability for next-generation designs and their area and power costs. This dissertation focuses on all of the above points, by describing a NoC architectural implementation called ×pipes; a NoC simulation environment within a cycle-accurate MPSoC emulator called MPARM; a NoC design flow consisting of a front-end tool for optimal NoC instantiation, called SunFloor, and a set of back-end facilities for the study of NoC physical implementations. This dissertation proves the viability of NoCs for current and upcoming designs, by outlining their advantages (alongwith a fewtradeoffs) and by providing a full NoC implementation framework. It also presents some examples of additional extensions of NoCs, allowing e.g. for increased fault tolerance, and outlines where NoCsmay find further application scenarios, such as in stacked chips.

Memory hierarchy and data communication in heterogeneous reconfigurable SoCs

The miniaturization race in the hardware industry aiming at continuous increasing of transistor density on a die does not bring respective application performance improvements any more. One of the most promising alternatives is to exploit a heterogeneous nature of common applications in hardware. Supported by reconfigurable computation, which has already proved its efficiency in accelerating data intensive applications, this concept promises a breakthrough in contemporary technology development. Memory organization in such heterogeneous reconfigurable architectures becomes very critical. Two primary aspects introduce a sophisticated trade-off. On the one hand, a memory subsystem should provide well organized distributed data structure and guarantee the required data bandwidth. On the other hand, it should hide the heterogeneous hardware structure from the end-user, in order to support feasible high-level programmability of the system. This thesis work explores the heterogeneous reconfigurable hardware architectures and presents possible solutions to cope the problem of memory organization and data structure. By the example of the MORPHEUS heterogeneous platform, the discussion follows the complete design cycle, starting from decision making and justification, until hardware realization. Particular emphasis is made on the methods to support high system performance, meet application requirements, and provide a user-friendly programmer interface. As a result, the research introduces a complete heterogeneous platform enhanced with a hierarchical memory organization, which copes with its task by means of separating computation from communication, providing reconfigurable engines with computation and configuration data, and unification of heterogeneous computational devices using local storage buffers. It is distinguished from the related solutions by distributed data-flow organization, specifically engineered mechanisms to operate with data on local domains, particular communication infrastructure based on Network-on-Chip, and thorough methods to prevent computation and communication stalls. In addition, a novel advanced technique to accelerate memory access was developed and implemented.