A mass transfer model applied to the supercritical extraction with CO2 of curcumins from turmeric rhizomes (Curcuma longa L)

ABSTRACT: Increasing restrictions on the use of artificial pigments in the food industry, imposed by the international market, have increased the importance of raw materials containing natural pigments. Of those natural substances with potential applications turmeric rhizomes (Curcuma longa L), are one of the most important natural sources of yellow coloring. Three different pigments (curcumin, desmetoxycurcumin, and bis-desmetoxycurcumin) constitute the curcuminoids. These pigments are largely used in the food industry as substitutes for synthetic dyes like tartrazin. Extraction of curcuminoids from tumeric rhizomes with supercritical CO2 can be applied as an alternative method to obtain curcuminoids, as natural pigments are in general unstable, and hence degrade when submitted to extraction with organic solvents at high temperatures. Extraction experiments were carried out in a supercritical extraction pilot plant at pressures between 25 and 30 MPa and a temperature of 318 K. The influence of drying pretreatment on extraction yield was evaluated by analyzing the mass transfer kinetics and the content of curcuminoids in the extracts during the course of extraction. The chemical identification of curcuminoids in both the extract and the residual solid was performed by spectrophotometry. Mass transfer within the solid matrix was described by a linear first-order desorption model, while that in the gas phase was described by a convective mass transfer model. Experimental results showed that the concentration profile for curcuminoids during the supercritical extraction process was higher when the turmeric rhizomes were submitted to a drying pretreatment at 343 K.

Extração de oleoresina de Cúrcuma (Curcuma longa l) com CO2 supercrítico

Dentre as fontes de corantes naturais mais utilizadas na indústria de alimentos, encontra-se a cúrcuma (Curcuma longa L.) uma rizomaina do qual podem ser obtidas substâncias como a curcumina, demetoxicurcumina e bis-demetoxicurcumina. Estes pigmentos possuem coloração amarela e capacidade de substituir corantes artificiais. Com a finalidade de verificar a influência do pré-tratamento de secagem na extração, foram realizados experimentos de extração de oleoresina de cúrcuma com CO2 supercrítico, na unidade de extração do Laboratório de Engenharia Química da Universidade Federal do Pará, submetendo-se a matéria-prima a uma secagem nas temperaturas de 70 e 105oC. As extrações foram feitas a pressões de 200, 250 e 300 bar, e na temperatura de 45oC. Os resultados estão apresentados em tabelas e gráficos, em termos de rendimentos totais e teor de curcumina presente na oleoresina. A secagem a 70oC favoreceu a extração de oleoresina em termos de tempo de extração, e contribuiu para a manutenção de curcumina na matéria-prima.

Integral transform solution for the forced convection of herschel-bulkley fluids in circular tubes and parallel-plates ducts

ABSTRACT: The thermal entry region in laminar forced convection of Herschel-Bulkley fluids is solved analytically through the integral transform technique, for both circular and parallel-plates ducts, which are maintained at a prescribed wall temperature or at a prescribed wall heat flux. The local Nusselt numbers are obtained with high accuracy in both developing and fully-developed thermal regions, and critical comparisons with previously reported numerical results are performed.

Integral transform method for laminar heat transfer convection of herschel-bulkley fluids within concentric annular ducts

ABSTRACT: Related momentum and energy equations describing the heat and fluid flow of Herschel-Bulkley fluids within concentric annular ducts are analytically solved using the classical integral transform technique, which permits accurate determination of parameters of practical interest in engineering such as friction factors and Nusselt numbers for the duct length. In analyzing the problem, thermally developing flow is assumed and the duct walls are subjected to boundary conditions of first kind. Results are computed for the velocity and temperature fields as well as for the parameters cited above with different power-law indices, yield numbers and aspect ratios. Comparisons are also made with previous work available in the literature, providing direct validation of the results and showing that they are consistent.

Determinação de parâmetros de transferência de massa do processo de extração supercrítica

A extração com fluido supercrítico de materiais líquidos e sólidos despertou o interesse para aplicações industriais nas últimas décadas, mais particularmente sob o conceito de química verde e biorrefinarias, portanto é fundamental que se faça uma modelagem desse processo a fim de otimizar as condições operacionais e simular o processo. O objetivo geral deste trabalho consiste na determinação de parâmetros de transferência de massa do processo de extração supercrítica de matriz sólida, empregando o dióxido de carbono como solvente, a partir de dados cinéticos de extração e na avaliação sistemática de cinco modelos matemáticos para descrever as cinéticas de extração dos óleos da polpa e da casca do buriti, do óleo de açaí de da oleoresina de cúrcuma, medidas no Laboratório de Extração Supercrítica, da Faculdade de Engenharia Química (UFPA), a fim de contribuir para o estudo de ampliação de escala e análise de custo de produção. Foram avaliados os modelos de Tan e Liou, Goto et al. (1993), Martinez et al. (2003), Esquível et al. (1999), e Sovová (1994). A modelagem das cinéticas de extração foi realizada utilizando aplicativos computacionais desenvolvidos e validados neste trabalho a partir de diferentes dados experimentais publicados na literatura. Diante de 40 cinéticas medidas com diferentes equipamentos de extração, configurações de leito, tipos de matérias primas, preparo dos materiais, pressão e temperatura e outros parâmetros de processo (com destaque ao rendimento global e a vazão de solvente), foi construído um panorama dos resultados acerca da capacidade dos modelos de transferência de massa em descrever as mais diferentes curvas globais de extração. De forma geral, os modelos de Goto et al. (1993) e Sovová (1994) apresentaram as melhores previsões aos dados experimentais das matérias primas tratadas neste trabalho com menores valores de quadrado, erros relativo, faixa de erro e desvios padrão e valores de R² próximos da unidade.

A statistical evaluation of the effects of process variables during catalytic hydrogenation of passion fruit (passiflora edulis) seed oil

ABSTRACT: Hydrogenation of passion fruit (passiflora edulis) seed oil was carried out with a commercial nickel/silica catalyst under different experimental conditions. The influence of reaction parameters (reaction temperature, hydrogen pressure, amount of catalyst, agitation rate and reaction time) on the response variable (iodine value) was studied using a central composite rotatable design and six center points for replication. Under the experimental conditions used, the model response equations for the iodine value showed good agreement with the experimental results.

Optimization of annatto (Bixa orellana L.) drying in fixed bed

ABSTRACT: The drying of annatto seeds (Bixa orellana L.), red piave cultivate, was studied in a fixed bed dryer. The best conditions were estimated to minimize the loss of coloring and to obtain final moisture of the seeds in appropriate levels to its conservation and maintenance of quality. The quantification of the influence of entrance variables in the final contents of bixin and moisture seeds and the identification of the optimal point was performed through the techniques of factorial design, response surfaces methodology, canonical analysis and desirability function. It was verified that the final moisture of the seeds may be estimated by a second-order polynomial model and that the final content of bixin is only significantly influenced by the time of drying being described properly by a linear model, for the seeds used in this study.

Supercritical extraction of pupunha (Guilielma speciosa) oil in a fixed bed using carbon dioxide

The pupunha (Guilielma speciosa) is the fruit of a palm tree typical of the Brazilian Northern region, whose stem is used as a source of heart of palm. The fruit, which is about 65% pulp, is a source of oil and carotenes. In the present work, an analysis of the kinetics of supercritical extraction of oil from the pupunha pulp is presented. Carbon dioxide was used as solvent. The extractions were carried out at 25 MPa and 323 K and 30 MPa and 318 K. The chemical composition of the extracts in terms of fatty acids was determined by gas chromatography. The amount of oleic acid, a saturated fatty acid, in the CO2 extracts was larger than that in the extract obtained with hexane. The overall extraction curves were modeled using the single-parameter model proposed in the literature to describe the desorption of toluene from activated coal.

Preliminary risk analysis applied to the handling of health-care waste

Between 75% and 90% of the waste produced by health-care providers no risk or is "general" health-care waste, comparable to domestic waste. The remaining 10-25% of health-care waste is regarded as hazardous due to one or more of the following characteristics: it may contain infectious agents, sharps, toxic or hazardous chemicals or it may be radioactive. Infectious health-care waste, particularly sharps, has been responsible for most of the accidents reported in the literature. In this work the preliminary risks analysis (PRA) technique was used to evaluate practices in the handling of infectious health-care waste. Currently the PRA technique is being used to identify and to evaluate the potential for hazard of the activities, products, and services from facilities and industries. The system studied was a health-care establishment which has handling practices for infectious waste. Thirty-six procedures related to segregation, containment, internal collection, and storage operation were analyzed. The severity of the consequences of the failure (risk) that can occur from careless management of infectious health-care waste was classified into four categories: negligible, marginal, critical, and catastrophic. The results obtained in this study showed that events with critics consequences, about 80%, may occur during the implementation of the containment operation, suggesting the need to prioritize this operation. As a result of the methodology applied in this work, a flowchart the risk series was also obtained. In the flowchart the events that can occur as a consequence of a improper handling of infectious health-care waste, which can cause critical risks such as injuries from sharps and contamination (infection) from pathogenic microorganisms, are shown.

On the prediction of pickup and saltation velocities in pneumatic conveying

This paper presents a comparative study of the critical pickup and saltation velocities of particles in horizontal pipelines for pneumatic conveying design. A comparative study is performed using different existing correlations in the literature for the determination of the minimum velocity of transport as a function of the particle and pipe diameter, particle density, solid mass flow rate and particle sphericity. Their limitations and difficulties in predicting those critical velocities are analyzed. For the pickup velocity, an experimental study was also carried out in order to support the analysis. Recommendations are presented on the use of such correlations.

Desorption of heavy metals from ion exchange resin with water and carbon dioxide

Adsorption and regeneration of ion exchange resins were studied using a subcritical solution of a CO₂-H₂O mixture and a fixed bed column. The commercial Amberlite IRC-50/IRC-86 cation exchange resins and Amberlite IRA-67 anion exchange resin were tested for heavy metals (Pb, Cu, Cd) adsorption from a solution with different initial metal concentrations at different temperatures. After adsorption, the loaded resins were regenerated with water and carbon dioxide at different temperatures and a pressure of 25 MPa. The efficiency of the IRC-50 resin was lower than that of the IRC-86 resin for the adsorption of metals like Cd, Cu and Pb. Results obtained for desorption of these metals indicated that the process could be used for Cd and in principle for Cu. Sorption of metal ions depended strongly on feed concentration. Mathematical modeling of the metal desorption process was carried out successfully as an extraction process. For this purpose, the VTII Model, which is applied to extraction from solids using supercritical solvents, was used in this work.