Simultaneous solidification of two catalyst wastes and their effect on the early stages of cement hydration

Two catalyst wastes (RNi and RAI) from polyol production were considered as hazardous, due to their respective high concentration of nickel and aluminum contents. This article presents the study, done to avoid environmental impacts, of the simultaneous solidification/stabilization of both catalyst wastes with type II Portland cement (CP) by non-conventional differential thermal analysis (NCDTA). This technique allows one to monitor the initial stages of cement hydration to evaluate the accelerating and/or retarding effects on the process due to the presence of the wastes and to identify the steps where the changes occur. Pastes with water/cement ratio equal to 0.5 were prepared, into which different amounts of each waste were added. NCDTA has the same basic principle of Differential Thermal Analysis (DTA), but differs in the fact that there is no external heating or cooling system as in the case of DTA. The thermal effects of the cement paste hydration with and without waste presence were evaluated from the energy released during the process in real time by acquiring the temperature data of the sample and reference using thermistors with 0.03 A degrees C resolution, coupled to an analog-digital interface. In the early stages of cement hydration retarding and accelerating effects occur, respectively due to RNi and RAl presence, with significant thermal effects. During the simultaneous use of the two waste catalysts for their stabilization process by solidification in cement, there is a synergic resulting effect, which allows better hydration operating conditions than when each waste is solidified separately. Thermogravimetric (TG) and derivative thermogravimetric analysis (DTG) of 4 and 24 h pastes allow a quantitative information about the main cement hydrated phases and confirm the same accelerating or retarding effects due to the presence of wastes indicated from respective NCDTA curves.

Desenvolvimento de equipamento motorizado para aplicação líquida de produtos fitossanitários na cultura do café

O trabalho teve como objetivo desenvolver um protótipo aplicador de líquidos na superfície do solo para cafezais localizados em regiões de topografia acidentada ou cultivados em sistema de plantio adensado. O protótipo do aplicador construído é um trator de rabiças acionado por um motor de dois tempos a gasolina, de 2,61 kW (3,5 cv), com duas rodas motrizes com bitola de 0,60 m e uma terceira roda direcional, equipado com sistema de pulverização dotado de depósito de 40 L, bomba centrífuga, filtros de linha, regulador de pressão, manômetro, mangueiras, válvulas e suporte de bicos. Para avaliar a eficiência do protótipo, foram instalados dois experimentos de campo em São Sebastião do Paraíso - MG (2003 e 2004), onde foram aplicados inseticidas sistêmicos para o controle da cigarra. Os métodos de aplicação avaliados foram: aplicação em faixa, filete, drench contínuo e drench intermitente. O protótipo aplicador de líquidos à superfície do solo atendeu aos objetivos propostos, visto que conseguiu realizar o controle químico de cigarras com destaque para a aplicação em drench contínuo. O protótipo, se equipado para aplicar simultaneamente nos dois lados da planta, apresentará capacidade de campo operacional semelhante à do equipamento tratorizado.

A Comparison of Deep Drawing and Ironing of Metal Alloy Strip Produced conventionally and Non-conventionally via Semi Solid Material Processing

A semi solid thin strip continuous casting process was used to obtain 50%wt Pb/50%wtSn strip by single and twin roll processing at speed of 15 m/min. A 50%wt Pb/50%wtSn plate ingot was also cast for rolling conventionally into strips of 1.4 mm thickness and 45 mm width for comparison with those achieved non-conventionally. This hypoeutectic alloy has a solidification interval and fusion temperature of approximately 31 degrees C and 215 degrees C respectively. The casting alloy temperature was around 280 degrees C as measured by a type K immersion thermocouple prior to pouring into a tundish designed to maintain a constant melt flow on the cooling slope during semi solid material production. A nozzle with a weir ensures that the semi solid material is dragged smoothly by the lower roll, producing strip with minimum contamination of slag/oxide. The temperatures of the cooling slope and the lower roll were also monitored using K type thermocouples. The coiled semi solid strip, which has a thickness of 1.5 mm and 45 mm width, was rolled conventionally in order to obtain 1.2 mm thick strip. The coiled thixorolled strip had a thickness of 1.2 mm and achieved practically the same width as the conventional strips. Blanks of 40 mm diameter were cut from the strips in a mechanical press, ready for deep drawing and ironing for mechanical characterization. All the strips achieved from non-conventional processing had the same mechanical performance as those achieved conventionally. The limiting drawing ratio (LDR) achieved was approximately 2.0 for all strips. Microscopy examination was made in order to observe phase segregation during processing.

Evaluation of strip rolling directly from the semi-solid state

defect metal alloy strip when thixorolling directly from the semi-solid state. To facilitate the study lead/tin alloys were chosen for their relatively low operating temperature. The objective is to extrapolate these findings to the higher temperature aluminium, alloys. Three alloys (70%Pb30%Sn, 60%Pb-40%Sn, 50%Pb-50%wtSn) were used particularly to study the influence of the solidification interval. The equipment consists of a two roll mill arranged as an upper and lower roller, where both rollers are driven at a controlled speed. The lower roller is fed with semi solid alloy through a ceramic nozzle attached to the lower end of a cooling slope. Several types of nozzle and their position at the roller were tested. This produced different solidifications and consequently different finished strip. The alloys were first cast and then poured onto the cooling slope through a tundish in order to create a continuous laminar flow of slurry and uniformity of metal strip quality. The pouring was tested at different positions along the slope. The cooling slope was coated with colloidal graphite to promote a smooth slurry flow and avoid the problem of adherence and premature solidification. The metallic slurry not only cools along the slope but is also initially super-cooled to a mush by the lower roller whilst at room temperatures, thus enabling thixorolling. It was also found that the nozzle position could be adjusted to enable the upper roller to also contribute to the solidification of the metallic slurry. However the rollers and the cooling slope naturally heat up. Temperature distribution in these zones was analysed by means of three thermocouples positioned along the cooling slope and a fourth in the base of the semi solid pool within the nozzle. The objective being to design an optimum pouring and cooling system. The formed strip was cooled down to room temperature with a shower of water. Microstructures of the thixorolling process were analysed. The differences in solidification conditions resulted in differing qualities of finished strip and corresponding defect types, all of which are a serious quality issue for the rolled product.

Nd:YAG Laser Irradiation of Etched/Unetched Dentin Through an Uncured Two-step Etch-and-Rinse Adhesive and its Effect on Microtensile Bond Strength

Purpose: To evaluate whether Nd:YAG laser irradiation of etched and unetched dentin through an uncured adhesive affected the microtensile bond strength (pTBS).Materials and Methods: Flat dentin surfaces were created in 19 extracted human third molars. Adper Single Bond (SB) adhesive was applied over etched (groups 1 to 3) or unetched dentin (groups 4 to 6). The dentin was then irradiated with a Nd:YAG laser through the uncured adhesive, using 0.75 or 1 W power settings, except for the control groups (groups 1 and 4). The adhesive was light cured and composite crowns were built up. After 24 h, the teeth were sectioned into beams, with cross-sectional areas of 0.49 mm(2), and were stressed under tension. Data were statistically analyzed using two-way ANOVA and Tukey's test (alpha = 5%). Dentin surfaces of fractured specimens and the interfaces of untested beams were observed under scanning electron microscopy (SEM).Results: Acid etching, laser irradiation, and their interaction significantly affected bonding (p < 0.05). Laser irradiation did not improve bonding of etched dentin to resin (p > 0.05). However, higher pTBS means were found on unetched lased dentin (groups 5 and 6), but only in comparison to group 4, where neither lasing nor etching was performed. Groups 4 to 6 showed the lowest pTBS means among all groups tested (p < 0.05). Laser irradiation did not change the characteristics of the hybrid layers created, while solidification globules were observed on lased dentin surfaces under SEM.Conclusion: Laser irradiation of dentin through the uncured adhesive did not significantly improve the pTBS in comparison to the suggested manufacturer's technique.

Analysis of Bothrops jararacussu venomous gland transcriptome focusing on structural and functional aspects: I - gene expression profile of highly expressed phospholipases A(2)

Snake venom glands are a rich source of bioactive molecules such as peptides, proteins and enzymes that show important pharmacological activity leading to in local and systemic effects as pain, edema, bleeding and muscle necrosis. Most studies on pharmacologically active peptides and proteins from snake venoms have been concerned with isolation and structure elucidation through methods of classical biochemistry. As an attempt to examine the transcripts expressed in the venom gland of Bothrops jararacussu and to unveil the toxicological and pharmacological potential of its products at the molecular level, we generated 549 expressed sequence tags (ESTs) from a directional cDNA library. Sequences obtained from single-pass sequencing of randomly selected cDNA clones could be identified by similarities searches on existing databases, resulting in 197 sequences with significant similarity to phospholipase A(2) (PLA(2)), of which 83.2% were Lys49-PLA(2) homologs (BOJU-1), 0.1% were basic Asp49-PLA(2)s (BOJU-II) and 0.6% were acidic Asp49-PLA(2)s (BOJU-III). Adjoining this very abundant class of proteins we found 88 transcripts codifying for putative sequences of metalloproteases, which after clustering and assembling resulted in three full-length sequences: BOJUMET-I, BOJUMET-II and BOJUMET-III; as well as 25 transcripts related to C-type lectin like protein including a full-length cDNA of a putative galactose binding C-type lectin and a cluster of eight serine-proteases transcripts including a full-length cDNA of a putative serine protease. Among the full-length sequenced clones we identified a nerve growth factor (Bj-NGF) with 92% identity with a human NGF (NGHUBM) and an acidic phospholipase A2 (BthA-I-PLA(2)) displaying 85-93% identity with other snake venom toxins. Genetic distance among PLA(2)s from Bothrops species were evaluated by phylogenetic analysis. Furthermore, analysis of full-length putative Lys49-PLA(2) through molecular modeling showed conserved structural domains, allowing the characterization of those proteins as group II PLA(2)s. The constructed cDNA library provides molecular clones harboring sequences that can be used to probe directly the genetic material from gland venom of other snake species. Expression of complete cDNAs or their modified derivatives will be useful for elucidation of the structure-function relationships of these toxins and peptides of biotechnological interest. (C) 2004 Elsevier SAS. All rights reserved.

Plasmodium falciparum: sequence diversity and antibody recognition of the Merozoite surface protein-2 (MSP-2) in Brazilian Amazonia

The merozoite surface protein-2 (MSP-2) of Plasmodium falciparum comprises repeats flanked by dimorphic domains defining the allelic families FC27 and IC1. Here, we examined sequence diversity at the msp-2 locus in Brazil and its impact on MSP-2 antibody recognition by local patients. Only 25 unique partial sequences of msp-2 were found in 61 isolates examined. The finding of identical msp-2 sequences in unrelated parasites, collected 6-13 years apart, suggests that no major directional selection is exerted by variant-specific immunity in this malaria-endemic area. To examine antibody cross-reactivity, recombinant polypeptides derived from locally prevalent and foreign MSP-2 variants were used in ELISA. Foreign IC1-type variants, such as 3D7 (currently tested for human vaccination), were less frequently recognized than FC27-type and local IC1-type variants. Antibodies discriminated between local and foreign IC1-type variants, but cross-recognized structurally different local IC1-type variants. The use of evolutionary models of MSP-2 is suggested to design vaccines that minimize differences between local parasites and vaccine antigens. (C) 2004 Elsevier B.V. All rights reserved.

Partitioning the relative fitness effects of diet and trophic morphology in the threespine stickleback

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Broiler walking ability and toe asymmetry under harsh rearing conditions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Larvas de Scinax rizibilis (Bokermann) (Anura, Hylidae): avaliando o efeito parental

A controlled experiment, related with the mating system of Scinax rizibilis (Bokermann, 1964), was conducted to assess if larval variation could be due to size of male or its ability to manage an amplexus. Adult individuals were caught during breeding activity (from February 1993 to January 1994), in a temporary pond in the municipality of Ribeirão Branco. São Paulo State, southeastern Brazil. The duration of the larval period was not different between tadpoles of large and small males, nor was it different between tadpoles coming from natural or artificial pairs. The reproductive status of the male (if it had managed an amplexus) also did not influence the total length nor the mass of the tadpoles close to metamorphosis. However, tadpoles of larger and heavier males were, on average, approximately 5.5% and 11% larger and heavier, respectively, than tadpoles of smaller males. These results indicate that the breeding system of S. rizibilis could potentially have a directional effect on the larval characteristics.

Avaliação da qualidade do corte florestal com motosserra

Objetivou-se, com esta pesquisa, avaliar a qualidade do corte florestal com motosserra, em propriedades rurais no sul do Espírito Santo, considerando aspectos da qualidade e a perda de madeira retida nas cepas. Foram lançadas parcelas de 250 m², onde foram feitas as observações após o corte com motosserra, avaliando-se a qualidade do corte nos seguintes aspectos: presença de espetos; danos por rachadura; cepas com faixa de ruptura fora do padrão; cepas sem o entalhe direcional e a altura da cepa remanescente, com vistas a mensurar a perda de madeira retida nas cepas. de acordo com os resultados, em média, houve presença de espetos em 21,9% das cepas, de rachaduras em 17,2%, de cepas fora do padrão em 44,6% e de cepas sem entalhe direcional em 34,5% das avaliações. Para verificar a influência da realização do entalhe direcional na altura das cepas, o teste-t, a 5% de probabilidade demonstrou que há contribuição para ocorrer maior altura de cepas, nos casos em que o corte foi feito sem o entalhe direcional. A quantidade de madeira retida nas cepas, acima do máximo recomendado, foi, em média, de 2,43 m³/ha, representando um prejuízo de R$ 172,53/ha. Foi verificada que a perda de madeira remanescente nas cepas de eucalipto foi maior nos locais onde, para a derrubada das árvores, não houve a realização do entalhe direcional. Os itens avaliados demonstraram qualidade irregular, indicando a necessidade de melhoria no corte com motosserras.

Dental caries and the nutritional status of preschool children: a spatial analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)