Vitrocerâmicas de alta resistência mecânica obtidas a partir da cristalização do sistema SiO2-Al2O3-MgO-Li2O com adição de ZrO2 e B2O3

Pós-graduação em Engenharia Mecânica - FEG

Properties of glass-ceramics obtained from crystallization of the SiO2-Al2O3-MgO-Li2O system with addition of ZrO2

This paper presents the study results with glass-ceramics obtained from base glass (MgO-Al2O3- SiO2-Li2O system) with addition of ZrO2 as nucleating agent. The glass was melted at 1650 degrees C for 3 h and at a heating rate of 10 degrees C/min. The molten glass was poured into a graphite mold to obtain monolithic samples and also in water in order to obtain particulate material. Such material was grinded and then pressed by both uniaxial and isostatic pressing methods before being sintered. Both the monolithic and pressed samples were performed under two different conditions of heat treatment so that their nucleation and crystallization occurred. In the first one, the samples were heated to 1100 degrees C with a heating rate of 10 degrees C/min. In the second one, there was an initial heating rate of 10 degrees C/min up to 780 degrees C, which was kept for 5 minutes. After that, the samples were heated to 1100 degrees C at a heating rate of 1 degrees C/min. Microhardness analyses showed that base glass presented values around 7.0 GPa. The glass-ceramics obtained from the powder sintering showed microhardness values lower than those obtained from monolithic samples. The highest hardness values were observed in the samples which were treated with two heating rates, whose values were around 9.2 +/- 0.5 GPa. Moreover, the glass-ceramics which were produced with an only heating rate, presented values around 7.1 +/- 0.2 GPa, very close to those observed in the base glass.

Structural and optical properties of Er3+ doped SiO2-Al2O3-GeO2 compounds prepared by a simple route

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A comparative evaluation of the CF:CS and CRS models in Pb-210 chronological studies applied to hydrographic basins in Brazil

The Constant Flux: Constant Sedimentation (CF:CS) and Constant Rate of Supply (CRS) of unsupported/excess Pb-210 models have been applied to a Pb-210 data set providing of eighteen sediments profiles sampled at four riverine systems occurring in Brazil, South America: Corumbatai River basin (S1=Site 1, Sao Paulo State), Atibaia River basin (S2=Site 2, Sao Paulo State), Ribeirao dos Bagres basin (S3=Site 3, Sao Paulo State) and Amazon River mouth. (S4=Site 4, Amapa State). These sites were chosen for a comparative evaluation of the performance of the CF:CS and CRS models due to their pronounced differences on the geographical location, geological context, soil composition, biodiversity, climate, rainfall, and water flow regime, among other variable aspects. However, all sediments cores exhibited a common denominator consisting on a database built from the use of the same techniques for acquiring the sediments major chemical composition (SiO2, Al2O3, Na2O, K2O, CaO, MgO, Fe2O3, MnO, P2O5, TiO2 and LOI-Loss on Ignition) and unsupported/excess 210Pb activity data. In terms of sedimentation rates, the performance of the CRS model was better than that of the CF:CS model as it yielded values more compatible with those expected from field evidences. Under the chronological point of view, the CRS model always provided ages within the permitted range of the Pb-210-method in the studied sites, whereas the CF:CS model predicted some values above 150 years. The SiO2 content decreased in accordance with the LOI increase in all cores analyzed and such inverse relationship was also tracked in the SiO2-LOI curves of historical trends. The SiO2-LOI concentration fluctuations in sites S1 and S3 also coincided with some Cu and Cr inputs in the drainage systems. (C) 2014 Elsevier Ltd. All rights reserved.

Pb-210 and composition data of near-surface sediments and interstitial waters evidencing anthropogenic inputs in Amazon River mouth, Macapa, Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Pb-210-derived chronology in sediment cores evidencing the anthropogenic occupation history at Corumbata River basin, Brazil

Activity profiles of excess Pb-210 combined with chemical data determined in two sediment cores from Corumbatai River basin, São Paulo State, Brazil, provided new insights into the reconstruction of historical inputs of anthropogenic constituents, contributing to improving management strategies of the hydrological resources in the basin since most of the municipalities extensively utilize the waters of Corumbatai River and tributaries for drinking purposes, among other uses. Excellent significant relationships between loss on ignition (LOI) and organic matter were found for sediments of both analyzed profiles. Silica was found to be inversely related to organic matter at both analyzed profiles: its decrease accompanied an increase in the specific surface of the sediments. This relationship was confirmed by a great number of inverse significant correlations among silica and oxides Na2O, K2O, CaO, MgO, Al2O3, P2O5, Fe2O3, MnO, and TiO2. It was possible to identify the role of organic matter on adsorption of several oxides/elements in the core sediments profiles. Apparent sediment mass accumulation rates corresponding to 224 and 802 mg cm(-2) year(-1) were obtained, and are compatible with field evidence, indicating a higher value associated with sand mining activities interfering with the natural/normal sedimentation process, due to modifications of the channel drainage.

Understanding the Crystallization Mechanism of a Wollastonite Base Glass Using Isoconversional, IKP Methods and Master Plots

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preparation of new glass systems by the polymeric precursor method for dental applications

Glass ionomer cements (GICs) are largely employed in Dentistry for several applications, such as luting cements for the attachment of crowns, bridges, and orthodontic brackets as well as restorative materials. The development of new glass systems is very important in Dentistry to improve of the mechanical properties and chemical stability. The aim of this study is the preparation of two glass systems containing niobium in their compositions for use as GICs. Glass systems based on the composition SiO2,Al2O3-Nb2O5-CaO were prepared by chemical route at 700degreesC. The XRD and DTA results confirmed that the prepared materials are glasses. The structures of the obtained glasses were compared to commercial material using FTIR, Al-27 and Si-29 MAS-NMR. The analysis of FTIR and MAS-NMR spectra indicated that the systems developed and commercial material are formed by SiO4 and AlO4 linked tetrahedra. These structures are essential to get the set time control and to have cements. These results encourage further applications of the experimental glasses in the formation of GICs. (C) 2004 Elsevier B.V. All rights reserved.

Crystal morphologies on a cordierite glass surface

With suitable thermal treatments, a nearly stoichiometric cordierite glass (2 MgO.2 Al2O3. 5 SiO2) shows a variety of crystal morphologies on the external surfaces: lozenges, regular and elongated hexagons, spherical and square shaped particles. We initially identified these morphologies through optical and scanning electron microscopy techniques. Their structural features were distinguished by x-ray diffraction patterns, infrared and Roman microprobe spectra. We concluded that there are close structural similarities for: lozenges and glass matrix; regular and elongated hexagons; spherical and square particles. The ordering degree increases in the following sequence: glass matrix, lozenges, hexagons, squares and spheres. The lozenge crystals are known as X-phase. The hexagons belong to the μ-cordierite (high quartz solid solution) metastable phase and the squares and spheres to the α-cordierite stable phase.

Chemistry of Biotites and Whole Rocks from the Rapakivi Itu Complex (Late Precambrian), State of São Paulo, SE Brazil

Chemical analyses for biotites and their host rocks from the Cabreúva (three facies) and Salto (five facies) intrusions from the multiple-centered rapakivi Itu Complex, State of São Paulo, Brazil, are presented and compared. The Cabreúva intrusion comprises different kinds of mainly even-grained biotite and hornblende-bearing syenogranites, monzogranites and quartz syenites and the Salto intrusion several types of mainly porphyritic biotite syenogranites, some of them hornblende-bearing. The biotites from the Salto intrusion (S-micas) show a more restricted composition than those from the Cabreúva intrusion (C-micas). This reflects the chemical variability of the two bodies which is smaller in the Salto intrusion and larger in the Cabreúva pluton. In the AlIV x Fet/(Fet+Mg) diagram the S- and C-micas show similar AlIV contents, around 2.2-2.3, but C-micas have higher Fet/(Fet+Mg) ratios (0.7-0.9) compared to those of S-micas (0.5-0.6). In the Mg:(Al+Fe+3+Ti):(Fe+2+Mn) diagram the S-micas are defined as Fe+2-biotites and the C-micas occupy the area between the Fe+2-biotites and the siderophyllite/lepidomelane fields, slightly overlapping the latter. In the Al2O3 × FeOt, MgO × FeOt, Al2O3 x MgO and Alt x Mg diagrams, the S-micas always lie on the calc-alkaline/alkaline boundary (or in the subalkaline field) whereas the C-micas systematically plot in the alkaline field, reflecting the higher alkalis content of the Cabreúva intrusion. In the Fet/(Fet+Mg) x SiO2 diagram, the S-micas lie on a smooth line whereas the C-micas from the different facies are separated by distinct chemical gaps reflecting the major or minor chemical overlapping of the facies from the Salto and Cabreúva intrusions.

Relações solo-paisagem em uma litosseqüência arenito-basalto na região de Pereira Barreto, SP

Os objetivos deste trabalho foram estudar as relações solo-paisagem em uma litosseqüência de transição arenito-basalto e verificar a similaridade dos limites de superfícies geomórficas mapeados no campo com os limites mapeados a partir de técnicas geoestatísticas. Foi realizado o mapeamento de uma área de 530 ha, utilizando-se equipamento de GPS, e em seguida elaborou-se o Modelo de Elevação Digital, que possibilitou o estabelecimento da transeção de 2.100 m a partir do topo. Ao longo da transeção, o terreno foi estaqueado a intervalos regulares de 50 m, nos quais foram realizadas medidas da altitude para confecção do perfil altimétrico. As superfícies geomórficas foram identificadas e delimitadas conforme critérios topográficos e estratigráficos, com base em intensas investigações de campo. Coletaram-se amostras de solo em pontos laterais em 67 locais, nas superfícies geomórficas identificadas, nas profundidades de 0,0-0,25 m e 0,80-1,00 m. Além disso, foram abertas trincheiras nos segmentos de vertente inseridos nas superfícies geomórficas mapeadas. As amostras coletadas foram analisadas quanto a densidade do solo, textura, Ca2+, K+, Mg2+, SB, CTC, V, pH (água e KCl), SiO2, Al2O3 e Fe2O3 (ataque por H2SO4), óxidos de Fe livres extraído com ditionito-citrato-bicarbonato e ferro mal cristalizado extraídos com oxalato de amônio. A fração argila desferrificada foi analisada por difração de raios X. A compartimentação da paisagem em superfícies geomórficas e a identificação do material de origem mostraram-se bastante eficientes para entendimento da variação dos atributos do solo. A análise individual desses atributos por meio de estatística univariada auxiliou na discriminação das três superfícies geomórficas. O uso de técnicas de geoestatística permitiu a confirmação de que mesmo os atributos do solo apresentaram limites próximos aos das superfícies geomórficas.

Relações solo-paisagem em topossequência de origem basáltica

Variações nos atributos do solo dependem da posição do solo na paisagem e processos de drenagem, erosão e deposição. Este estudo objetivou avaliar os atributos físicos e químicos do solo, em uma topossequência de origem basáltica, na região de Batatais (SP). A área possui relevo aplanado e altitude oscilando entre 740 m e 610 m, em região dominada por basaltos. Foi estabelecido caminhamento de 3.000 m, a partir do espigão da vertente, no seu declive mais suave. As superfícies geomórficas foram identificadas e delimitadas conforme critérios topográficos e estratigráficos, com base em intensas investigações detalhadas de campo. Foram coletadas amostras laterais aos perfis modais representativos das diversas superfícies geomórficas (S.G.) da topossequência (S.G. I = topo; S.G. II = meia encosta e sopé de transporte; S.G. III = ombro e sopé de deposição), totalizando 142 amostras. Além disto, foram abertas trincheiras, nos segmentos de vertente inseridos nas superfícies geomórficas mapeadas. As amostras coletadas foram analisadas quanto à densidade do solo, textura, bases trocáveis (Ca2+, K+ e Mg2+), soma de bases, capacidade de troca catiônica, saturação por bases, pH (água e KCl), SiO2, Al2O3, Fe2O3 (ataque por H2SO4), óxidos de Fe livres extraídos com ditionito-citrato-bicarbonato e Fe mal cristalizado extraído com oxalato de amônio. Os resultados revelaram que os solos oriundos de basalto apresentaram atributos físicos e químicos com comportamento dependente das formas do relevo. Com o uso de técnicas estatísticas multivariadas, foi possível distinguir três diferentes ambientes, que equivalem às três superfícies geomórficas.

Modelos de paisagem e susceptibilidade magnética na identificação e caracterização do solo

O conhecimento detalhado do solo e de seus atributos, ao longo da paisagem, é uma demanda permanente dos sistemas urbanos e agroindustriais, para o planejamento sustentável de uso e ocupação. O presente trabalho objetivou estudar o potencial de modelos de paisagem e susceptibilidade magnética na identificação e caracterização de latossolos, em Guariba (SP). Foram coletadas 514 amostras de solo, em 110,0 ha, às profundidades de 0,0-0,20 m e 0,60-0,80 m. Foram identificados diferentes compartimentos de paisagem, com base no modelo de superfície geomórfica e segmento de vertente. em cada compartimento de paisagem, foram abertas trincheiras, para classificação do solo. As amostras foram analisadas quanto à granulometria e atributos químicos, pH (água, CaCl2 e KCl), matéria orgânica, P extraível, K+, Ca2+, Mg2+ e H+ + Al3+. Também foram determinados os teores de SiO2, Al2O3, Fe2O3 e óxidos de Fe livres (Fe d) e pouco cristalizados (Fe o), nas amostras das trincheiras, além da susceptibilidade magnética (SM). Solos taxonomicamente iguais, porém em diferentes compartimentos da paisagem, apresentaram valores distintos, para os atributos estudados, indicando que os modelos de paisagem e a susceptibilidade magnética podem ser viáveis, como técnica de campo, para auxiliar no detalhamento da variação dos atributos do solo. A susceptibilidade magnética demonstrou ter potencial para delimitação das superfícies geomórficas mapeadas no campo, o que indica o seu potencial de uso, na identificação e caracterização de áreas mais homogêneas.

Solos do assentamento malhada do meio, Chapadinha-MA: classificação e variabilidade espacial de seus atributos

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Suscetibilidade magnética e sua associação com atributos do solo e do relevo em uma topossequência de Latossolos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)